VAUXHALL Ampera 0-1 VAUXHALL Ampera Owner’s Manual Model Year 2012 Edition: September 2011 TS 1710-B-12
Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 19 Seats, restraints ........................... 32 Storage ........................................ 49 Instruments and controls ............. 54 Lighting ........................................ 90 Climate control ............................. 95 Driving and operating ................. 101 Vehicle care ...............................
2 Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
4 Introduction Danger, Warnings and Cautions 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Disregarding this information may endanger life. 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3.
Introduction 5
6 In brief In brief Vehicle unlocking Open&Start Radio remote control Initial drive information Press button ( to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, press the button under the tailgate moulding. Radio remote control 3 20, Central locking system 3 23, Load compartment 3 25. With the radio remote control within the opening range, simply press the lock/unlock button on the door handle to unlock the driver's door.
In brief Seat adjustment Seat backrests Seat height Pull lever, adjust inclination and release lever. Allow the seat to engage audibly. Seat position 3 33, Seat adjustment 3 34. Lever pumping motion: up = seat higher down = seat lower 7 Seat positioning Pull handle, slide seat, release handle. Seat position 3 33, Seat adjustment 3 34. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. Seat position 3 33, Seat adjustment 3 34.
8 In brief Head restraint adjustment Inclination adjustment Seat belt To adjust horizontally, pull the head restraint forwards. It engages in several positions. To return to its rearmost position, pull fully forwards and release. Head restraints 3 32. Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle.
In brief Mirror adjustment 9 Exterior mirrors Steering wheel adjustment Select the relevant exterior mirror and adjust. Convex exterior mirrors 3 28, Electric adjustment 3 28, Folding exterior mirrors 3 29, Heated exterior mirrors 3 29. Unlock lever (A), adjust steering wheel, then engage lever and ensure it is fully locked. Do not adjust steering wheel unless vehicle is stationary and steering wheel lock has been released. Airbag system 3 40.
10 In brief Instrument panel overview
In brief A B C D E F G H I J K L M O P Q R S T Heated front seats ................ 35 Automatic climate control ...... 95 Instrument panel storage ...... 49 Charge status indicator ....... 127 Daytime running light ............ 90 Colour-Info-Display ............... 69 Turn and lane-change signals ................................... 92 Light switch ........................... 90 Pedestrian safety alert .......... 55 Instrument cluster display ..... 68 Driver Information Centre (DIC) ......................
12 In brief Exterior lighting Turn adjuster wheel: AUTO = automatic light control: Exterior lighting is switched on and off automatically depending on external lighting conditions. m = exterior lighting is switched off. = sidelights 8 = headlights 9 Turn and lane-change signals r = Turn the rear fog lamp band on the lever to r and release it, to turn the rear fog lamp on or off. The band will return to its original position.
In brief Hazard warning flashers Horn 13 Pedestrian safety alert Press j. Horn 3 55. Operated with the ¨ button. Hazard warning flashers 3 91. Use this feature to alert people who may not hear your vehicle approaching. Momentarily push 4 on the end of the turn and lane-change lever and a soft‐ note alert will momentarily sound. Repeat for additional activations of the pedestrian safety alert. Pedestrian safety alert 3 55.
14 In brief Washer and wiper systems Adjustable wiper interval Heated rear window, heated exterior mirrors Windscreen wiper 2 1 5 § = = = = fast slow interval wiping Off For a single wipe, press the lever down to 5. For several wipes, hold the lever down. Do not use if the windscreen is frozen. Switch off in car washes. Windscreen wiper 3 55, Wiper blade replacement 3 142. Climate control Wiper lever in position 5.
In brief Automatic climate control system 3 95. Electric drive unit P R N D L = = = = = Park Reverse Neutral Drive Low The shift lever can only moved out of P when the ignition is on, the regular brake is applied first and then the shift lever button is pressed. If you are not able to shift out of P (Park), ease pressure on the shift lever, then push the shift lever all the way into P (Park) as you maintain 15 brake application.
16 In brief Starting off Starting the vehicle Check before starting off ■ Tyre pressure and condition 3 156, 3 185. ■ Engine oil level and fluid levels 3 138. ■ All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and are operational. ■ Proper position of mirrors, seats, and seat belts 3 28, 3 33, 3 37. ■ Brake function at low speed, particularly if the brakes are wet.
In brief 17 mode transitions the vehicle to extended range mode to maintain the battery charge reserve. Hold mode will not change normal vehicle acceleration or braking performance. Electric vehicle operation modes 3 106. Operated with the DRIVE MODE button. Press DRIVE MODE as long as the desired drive mode is highlighted. Then release the DRIVE MODE button. Sport: This mode provides more responsive acceleration than normal mode, but can reduce efficiency.
18 In brief Parking ■ Do not park the vehicle on an easily ignitable surface. Things that can burn could touch hot exhaust parts under the vehicle and ignite. ■ Always apply the electrical parking brake. Pull switch m. ■ Switch off the ignition. Turn the steering wheel until the steering wheel lock engages. ■ If the vehicle is on a level surface or uphill slope, set the parking brake and then shift the selector lever to P, before switching off the ignition.
Keys, doors and windows Keys, doors and windows Keys, locks 19 Key with foldaway key section Keys Replacement keys The key number is specified in the Car Pass or on a detachable tag. The key number must be quoted when ordering replacement keys as it is a component of the immobiliser system. Locks 3 173. Lock cylinders Designed to free-wheel if they are forcefully rotated without the correct key or if the correct key is not fully inserted.
20 Keys, doors and windows Radio remote control The radio remote control has an approximate range of up to 200 feet. It can be restricted by external influences. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation.
Keys, doors and windows The remote start can be initiated two separate times between driving. For each remote start, the passenger compartment will be heated or cooled for 10 minutes. Extending the time To extend the time of the first remote start, repeat the steps for activating remote start. Remote start can only be extended once between driving.
22 Keys, doors and windows To replace the battery: 1. Extend the key and open the battery cover on the back of the unit. 2. Remove the used battery. Avoid touching the circuit board to other components. 3. Replace the battery (battery type CR 2032), paying attention to the installation position. 4. Close the unit. 5. Check the operation of the radio remote control. Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point.
Keys, doors and windows Locking Driver door handle To lock the doors, press the lock/ unlock button on the door handle if: ■ More than five seconds have passed. ■ The lock/unlock button was used to unlock all doors. ■ All doors are closed. Passenger door handle To lock the doors, press the lock/ unlock button on the door handle if: ■ The lock/unlock button was used to unlock all doors. ■ All doors are closed.
24 Keys, doors and windows Central locking buttons Locks or unlocks all doors. Press the ) button to lock. Press the ( button to unlock. Delayed locking If delayed locking is enabled, a chime will sound to indicate that any door or the tailgate is open when the doors are locked with the ) button on the instrument panel. The doors will automatically lock and the theftdeterrent system will arm after all doors are closed and five seconds have passed. Press ) again to lock the doors immediately.
Keys, doors and windows The rear door child locks prevent passengers from opening the rear doors from inside the vehicle. Press H% to activate. The LED (A) comes on when activated. Press H% again to deactivate. Doors 25 Closing Load compartment Tailgate Opening To open the tailgate with all doors unlocked, press the button on the underside of the tailgate handle and lift up. Use the inside pull handle to lower and close the tailgate. Always close the tailgate before driving.
26 Keys, doors and windows General hints for operating tailgate 9 Warning Do not drive with the tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases, which can not be seen or smelled, could enter the vehicle. This can cause unconsciousness and even death. Caution Before opening the tailgate, check overhead obstructions, such as a garage door, to avoid damage to the tailgate. Always check the moving area above and behind the tailgate.
Keys, doors and windows Anti-theft alarm system It monitors: ■ Doors, tailgate, bonnet ■ Passenger compartment including adjoining load compartment ■ Vehicle inclination, e.g. if it is raised ■ Removing of the charge cord Activation ■ Press the ) button on the radio remote control after all of the doors and windows have been closed. ■ Press the ) button on the instrument panel when the Prevent doorlock while door open function is turned off. Vehicle personalisation 3 82.
28 Keys, doors and windows If the vehicle loses battery power when the anti-theft alarm system is armed, the power sounder will activate automatically. The number and duration of alarm signals are stipulated by legislation. To turn off the system alarm: ■ Press ( on the radio remote control or ■ Start the vehicle by pressing the m button on the instrument panel with the brake pedal applied and the radio remote control located inside the vehicle.
Keys, doors and windows Select the relevant exterior mirror by moving the selector switch to left (L) or right (R). Then press the arrows on the control pad to adjust the respective mirror. In the centre position of the selector switch no mirror is selected. Folding For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing.
30 Keys, doors and windows The passenger and rear windows can just be lowered without holding the switch. Power windows can work until the driver's door is opened or at the latest for 10 minutes after the ignition is switched off. Child safety system for rear windows Safety function Operate the switch for the respective window by pushing to open or pulling to close. Pushing or pulling gently to the first detent: window moves up or down as long as the switch is operated.
Keys, doors and windows Activate the window electronics as follows: 1. Close all doors with the ignition on or when retained power off is active. 2. Pull switch until the window is closed and keep pulling for additional 2 seconds. 3. Repeat for each window. Press and hold ( button to open windows. Release button to stop window movement. Overload If the windows are repeatedly operated within short intervals, the window operation is disabled for some time.
32 Seats, restraints Seats, restraints Head restraints Adjustment Head restraints on front seats Position 9 Warning Only drive with the head restraint set to the proper position. Height adjustment Press the button, adjust height and make sure that the head restraint is engaged. The upper edge of the head restraint should be at upper head level. If this is not possible for extremely tall people, set to highest position, and set to lowest position for small people.
Seats, restraints Head restraints on rear seats 33 Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. Inclination adjustment To adjust horizontally, pull the head restraint forwards. It engages in several positions. To return to its rearmost position, pull fully forwards and release. Height adjustment Pull the head restraint upwards or press the catch to release and push the head restraint downwards. Make sure that the head restraint is engaged.
34 Seats, restraints ■ Sit with shoulders as far back against the backrest as possible. Set the backrest rake so that it is possible to easily reach the steering wheel with arms slightly bent. Maintain contact between shoulders and the backrest when turning the steering wheel. Do not angle the backrest too far back. We recommend a maximum rake of approx. 25°. ■ Adjust the steering wheel 3 54. ■ Set seat height high enough to have a clear field of vision on all sides and of all display instruments.
Seats, restraints Lever pumping motion: up = seat higher down = seat lower Auto heated seats Heating Manual heated seats Adjust heating to the desired setting by pressing the ß button for the respective seat one or more times. The LEDs next to the heating symbol indicate the setting. Prolonged use of the highest setting for people with sensitive skin is not recommended. Activation To activate auto heated seats: 1. Press the Climate control button on the instrument panel. 2.
36 Seats, restraints Remote start heated seats When it is cold outside, the heated seats can be programmed to turn on automatically during a remote vehicle start. Unless the auto heated seats function is available and enabled, the heated seats will be cancelled when the vehicle is turned on. If the auto heated seats function is enabled, the seat heating level will automatically change to the level required by the vehicle's interior temperature when the ignition is switched on.
Seats, restraints 9 Warning Incorrect handling (e.g. removal or fitting of belts) can trigger the belt pretensioners. Three-point seat belt Fastening Deployment of the belt pretensioners is indicated by continuous illumination of control indicator v 3 61. Triggered belt pretensioners must be replaced by a workshop. Belt pretensioners can only be triggered once. Note Do not affix or install accessories or other objects that may interfere with the operation of the belt pretensioners.
38 Seats, restraints Removing There is one guide for each passenger position in the rear seat. When using a comfort guide, remove the seat belt from the seat‐mounted guide before using the comfort guide. To install a comfort guide to the seat belt, proceed as follows: 2. Place the guide over the belt, and insert the two edges of the seat belt into the slots of the guide. To release belt, press red button on belt buckle.
Seats, restraints 3. The seat belt should not be twisted and it should lie flat. The elastic cord must be under the seat belt and the guide on top. 9 Warning A seat belt that is not properly worn may not provide the protection needed in a crash. The person wearing the seat belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. 4.
40 Seats, restraints Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner. Note The airbag systems and belt pretensioner control electronics are located in the centre console area.
Seats, restraints Curtain airbag system 9 Warning The curtain airbag system consists of an airbag in the roof frame on each side. This can be identified by the word AIRBAG along the headliner or trim. The curtain airbag system is triggered in the event of a side-on impact of a certain severity. The ignition needs to be switched on. Optimum protection is only provided when the seat is in the proper position 3 33. Keep the area in which the airbag inflates clear of obstructions.
42 Seats, restraints 9 Warning Keep the area in which the airbag inflates clear of obstructions. The hooks on the handles in the roof frame are only suitable for hanging up light articles of clothing, without coat hangers. Do not keep any items in these clothes. Knee airbag system The knee airbags are located below the steering column and below the glovebox. With knee airbags, the word AIRBAG will appear on the lower portion of the instrument panel.
Seats, restraints V: Front passenger frontal and knee airbags are active. A child restraint system must not be installed. 9 Danger Risk of fatal injury for a child using a child restraint system on a seat with activated front passenger frontal and knee airbag. Risk of fatal injury for an adult person on a seat with deactivated front passenger frontal and knee airbag.
44 Seats, restraints 9 Danger When using a child restraint system on the front passenger seat, the airbag systems for the front passenger seat must be deactivated; if not, the triggering of the airbags poses a risk of fatal injury to the child. This is especially the case if rearfacing child restraint systems are used on the front passenger seat. Selecting the right system The rear seats are the most convenient location to fasten a child restraint system.
Seats, restraints Child restraint installation locations Permissible options for fitting a child restraint system On front passenger seat Mass group activated airbag deactivated airbag On rear outboard seats Group 0: Up to 10 kg X U1 U Group 0+: Up to 13 kg X U1 U Group I: 9 to 18 kg X U1 U Group II: 15 to 25 kg X X U Group III: 22 to 36 kg X X U = Seating position must be adjusted to full up seat height travel.
46 Seats, restraints Mass group Size class Fixture On front passenger seat On rear outboard seats Group 0+: up to 13 kg E ISO/R1 X IL1 D ISO/R2 X IL2 C ISO/R3 X IL3 D ISO/R2 X IL2 C ISO/R3 X IL3 B ISO/F2 X IL, IUF B1 ISO/F2X X IL, IUF A ISO/F3 X IL Group I: 9 to 18 kg IL = Suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories. The ISOFIX restraint system must be approved for the specific vehicle type.
Seats, restraints B1 – ISO/F2X C – ISO/R3 D – ISO/R2 E – ISO/R1 F – ISO/L1 G – ISO/L2 = = = = = = Reduced‐height forward‐facing toddler child restraint system. Full‐size rear‐facing toddler child restraint system. Reduced‐size rear-facing toddler child restraint system. Rear‐facing infant child restraint system. Left side‐facing position carrycot. Right side‐facing position carrycot.
48 Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. No more than two ISOFIX child restraint systems can be installed on the rear seats at the same time. ISOFIX mounting brackets are indicated by a label & on the backrest. Top-tether fastening eyes The Top-Tether anchors for outboard rear seating positions are on the back of the rear seatback.
Storage Storage Storage compartments 49 Door panel storage Instrument panel storage There is a storage compartment on top of the instrument panel that includes an auxiliary power outlet. A transmitter slot for the radio remote control transmitter is located inside the storage compartment. Radio remote control 3 20. Glovebox Open the glove box by lifting up on the lever. The glovebox should be closed whilst driving. Slide an umbrella into the opening either the driver or passenger door.
50 Storage Load compartment Floor console storage Folding the seat backrests 9 Warning Inside the front of the floor console is an auxiliary power outlet (C) and jack for auxiliary input devices (B). Cords can be routed in the pass-through (A). For more information, see the infotainment manual. The console has cupholders and a storage area. The rear console has open storage with an auxiliary power outlet (A) and cupholders. Only drive the vehicle if the backrests are securely locked into position.
Storage Fold seat backrests up 3. Remove the seat belt from the seat belt guide (A) and place it in the storage clip (B). 4. Pull the seatback release lever to unlock the seatback and fold the seatback forward. Note Damage to the seat belt or seat backrest locking mechanism can occur if the seat belt is caught between the rear seat backrest and the seat backrest locking mechanism. The seat belt must be out of the way when the rear seat is raised to the upright, locked position.
52 Storage Loading information Warning triangle The warning triangle is located in the right rear cargo storage door. First aid kit The first aid kit is located in the right rear cargo storage door. ■ Heavy objects in the load compartment should be placed against the seat backrests. Make sure that the backrests are securely engaged. If objects can be stacked, heavier objects should be placed at the bottom. ■ Secure objects with lashing straps attached to lashing eyes.
Storage Optional equipment and accessories increase the kerb weight.
54 Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Unlock lever (A), adjust steering wheel, then engage lever and ensure it is fully locked. Do not adjust steering wheel unless vehicle is stationary and steering wheel lock has been released. The Infotainment system and the cruise control can be operated via the controls on the steering wheel.
Instruments and controls 55 Windscreen wiper/washer Windscreen wiper Further information is available in the Infotainment system manual. Cruise control 3 118. Horn Press the j symbol on the steering wheel to sound the horn. Do not use the horn as pedestrian safety alert. Pedestrian safety alert Pedestrian safety alert enables the driver to alert people who may not hear the vehicle approaching.
56 Instruments and controls Wiper lever in position 5. Turn the adjuster wheel to adjust the desired wipe interval: short = turn adjuster wheel interval upwards long = turn adjuster wheel interval downwards Windscreen washer Pull lever. Washer fluid is sprayed onto the windscreen and the wiper wipes a few times. Clock The clock is shown in the Colour-InfoDisplay. Set clock 1. Press the time program button to go directly to the time setting page or press the CONFIG button and select Time from the list.
Instruments and controls Do not connect any current-delivering accessories, e.g. electrical charging devices or batteries. Do not damage the outlets by using unsuitable plugs. Warning lights, gauges and indicators 57 Fuel gauge Speedometer Indicates vehicle speed. The shown unit can be changed in the Driver Information Centre (DIC). Driver Information Centre (DIC) 3 67. Odometer Displays the recorded distance.
58 Instruments and controls Battery gauge Driving efficiency gauge Total vehicle range This indicator displays the high voltage battery charge level. When this indicator is displayed in the foreground, the vehicle is operating in electric mode. The value next to the indicator displays an estimate of how far the vehicle can be driven while in this mode. Electric mode 3 106. This gauge is a guide to driving in an efficient manner by keeping the ball green and in the centre of the gauge.
Instruments and controls The system must be reset every time the engine oil is changed to allow proper functionality. Seek the assistance of a workshop. Avoid accidental resetting of the engine oil life system. It cannot be reset accurately until the next oil change. When the system has calculated that engine oil life has been diminished, Change Engine Oil Soon appears in the Driver Information Centre. Have engine oil and filter changed by a workshop within the next 600 miles.
60 Instruments and controls Control indicators in the instrument cluster
Instruments and controls Turn signal Illuminates or flashes green. Flashes The control indicator flashes if a turn signal or the hazard warning flashers are activated. Fast flashing: failure of a turn signal light or associated fuse. Bulb replacement 3 143. Fuses 3 147. Turn signals 3 92. Seat belt reminder Seat belt reminder on front seats X for driver's seat illuminates or flashes red. k for front passenger seat illuminates or flashes red, when seat is occupied.
62 Instruments and controls Driver Information Centre (DIC) 3 67. Airbag deactivation V illuminates yellow. The front passenger frontal and knee airbag are activated. W illuminates yellow. The front passenger frontal and knee airbag are deactivated 3 42. 9 Danger Risk of fatal injury for a child using a child restraint system on a seat with activated front passenger frontal and knee airbag. Risk of fatal injury for an adult person on a seat with deactivated front passenger frontal and knee airbag.
Instruments and controls Should the light continues to flash: 1. Move out of the flow of traffic as quickly as possible without impeding other vehicles. 2. Stop, switch off the ignition. 3. Wait at least 10 seconds and switch the ignition on again. If the light is still flashing, seek the assistance of a workshop. Brake system R illuminates red. Illuminates after the ignition is switched on. The brake fluid level is too low or any other problem with the brake system exists. Brake fluid level 3 140.
64 Instruments and controls When the ABS control indicator remains on after resetting the system or comes on again while driving, seek the assistance of a workshop. Antilock brake system 3 113. Should the warning lights of the ABS and the regular brake system come on, the vehicle may have a problem with the regular and the antilock brakes. Have the vehicle towed for service. Towing 3 172. Sport mode Sport illuminates when sport mode is selected. Sport mode 3 107.
Instruments and controls Caution If engine coolant temperature is too high, stop vehicle, switch off the ignition. Danger to engine. Check coolant level. If the control indicator remains on, seek the assistance of your workshop. Tyre pressure monitoring system A illuminates or flashes yellow. Illuminates One or more of the tyres are significantly underinflated. Stop immediately and check tyre pressure. Flashes Fault in system. After about one minute the control indicator illuminates continuously.
66 Instruments and controls Cruise control Door(s) open m illuminates white or green. Illuminates white The system is on. Illuminates green A certain speed is stored. Cruise control 3 118. Door open If a door, the bonnet or the tailgate is opened, a light comes on together with a graphic in the Driver Information Centre (DIC). Bonnet open Tailgate open The DIC indicates when a door, the bonnet, or the tailgate is open. The light displays the open area as shaded.
Instruments and controls Information displays Selecting menus and functions At the main DIC menu: 1. Turn the SELECT knob to scroll through the possible DIC menus. 2. Press the centre of the SELECT knob when a menu item is highlighted to enter that menu. 3. Continue to turn and press the SELECT knob to scroll through and select the available menu items: Driver Information Centre The Driver Information Centre (DIC) display is located in the instrument cluster.
68 Instruments and controls Seek the assistance of a workshop. Tyre pressure 3 156. Tyre pressure monitoring system 3 157. Vehicle messages 3 Turn the SELECT knob to scroll through any active warning message. Press SELECT to review the messages. Vehicle messages 3 81. Unit 7 Turn the SELECT knob to change the unit display between metric and imperial. Press SELECT to confirm the setting. Tutorial mode T A screen that explains some of the unique features of the cluster is displayed by selecting this item.
Instruments and controls 69 Colour-Info-Display This screen indicates that charging is active and the estimated charge completion time is 10:00 a.m. This screen indicates that the vehicle is fully charged and the charge cord is not connected. This screen indicates that charging is programmed to be delayed with an estimated completion time of 7:00 a.m. This screen indicates that the charge cord is connected, but the vehicle cannot be charged. Colour-Info-Display is located in the instrument panel.
70 Instruments and controls Battery Power‐ Battery is active with energy flowing to the wheels. Engine Power - Engine is active with energy flowing to the wheels. Battery Power - Vehicle is stationary in electric mode and no power is flowing to the wheels. Engine Power - Vehicle is stationary in extended range mode and no power is flowing to the wheels. To view Power Flow, Charging and Energy Info, press 8 on the instrument panel.
Instruments and controls 71 Charging Engine & Battery Power ‐ Both the engine and battery are active with energy flowing to the wheels. Regen Power Recovery ‐ Power from the wheels returns to the battery during regenerative braking or coasting. Power off ‐ No power is flowing to the wheels. Programmable charging There are three programmable charge modes.
72 Instruments and controls Charge mode status Immediately: The vehicle starts charging as soon as it is connected to an electrical outlet. Charging 3 125. Delayed (Departure Time): The vehicle estimates the charging start time considering the programmed departure time for the current day of the week. Charging begins at the start time and is complete by the departure time only if sufficient time is allowed after the charge cord is plugged in.
Instruments and controls location is required for this mode. Also, if the selected electric rate settings result in a very long charge completion time, the vehicle will start charging immediately upon plug-in. For example, if the electric rate table is setup with all peak rates and the rate preference is to charge during off-peak rates only, then the vehicle will start charging immediately upon plug-in. Charge mode selection From the charge mode status screen, press Change Charge Mode.
74 Instruments and controls ■ Reduced Level 2 - 9 Amps: Limits AC current to 9 ampere ■ Reduced Level 3 - 6 Amps: Limits AC current to 6 ampere Exact current levels for a particular region may vary from values shown in this manual. Please check vehicle for available levels. The charge level preference settings are not directly related to the charge level button on the charge cord. The vehicle will adhere to the setting that minimises the AC current used to charge the vehicle.
Instruments and controls Charging begins at the start time and is complete by the departure time only if sufficient time is allowed after the charge cord is plugged in. For example, if the vehicle is plugged in for only one hour prior to the departure time and the battery is completely discharged, the vehicle will not be fully charged by the departure time regardless of the rate selection.
76 Instruments and controls 1. Press Summer Start. 2. Press + or − to set the month and day for the start of summer. 3. Press Winter Start. 4. Press + or − to set the month and day for the start of winter. 5. Press Edit Summer Schedule or Edit Winter Schedule to edit the daily electric rate schedule. Electric rate schedule editing From the Enter Summer/Winter Start Dates screen, press Edit Summer Schedule or Edit Winter Schedule.
Instruments and controls 77 1. Press + or − to adjust the time. 2. Press Peak, Mid-Peak or OffPeak to select the electric rate. 3. Press Back to store changes. Only the finish time can be edited. The start time is automatically populated in the rate table. Electric rate schedule viewing From the Select Electric Rate Plan screen, press either View Summer Schedule, View Winter Schedule or View Yearly Schedule.
78 Instruments and controls the Colour-Info-Display, there are also other ways to temporarily override a delayed charge mode. Charging 3 125. To temporarily override a delayed charge mode to immediate charge mode from inside the vehicle: 1. Press the release button of the charge port door on the driver door to view the charge mode status pop-up in the Colour-InfoDisplay. 2. Press Temporary Override. 3. Press Charge Immediately on Plug-in to temporarily override an immediate charge mode.
Instruments and controls Charging override / interruption popup 2. Press Temporary Override. 3. Press the + or – button to change the next departure time. 4. Press Confirm Departure Time to temporarily override the next planned departure time. The revised charge complete time will be automatically displayed in the temporary charge mode screen. Temporary departure time can only be updated for the same day as the original next planned departure time.
80 Instruments and controls Programmable charging disabled If the programmable charging system is consistently disabled, seek the assistance of a workshop. Energy information To view the Energy Usage, Energy Efficiency and Efficiency Tips, press 8 on the instrument panel and then press Energy Info at the top of the touch screen. Energy Usage When the programmable charging system is disabled, the screen and the pop-up of the default charge mode status will display - -:- - for the charge complete time.
Instruments and controls This automatic pop-up can be disabled through the vehicle personalisation. Vehicle personalisation 3 82. Efficiency Tips Energy efficiency This screen is accessed by pressing Energy Efficiency on the Energy Usage screen. This screen displays the energy efficiency over the drive cycle based on driving style and climate settings. Driving in a more efficient manner will result in a higher percentage displayed for driving style.
82 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Instruments and controls Brakes Ride control systems Cruise control Object detection systems Lighting, bulb replacement Wiper/washer system Doors, windows Radio remote control Airbag systems Engine and electric drive unit Tyres Battery and charging Vehicle operation modes Speed limit Vehicle personalisation Vehicle Personalisation can be accessed by using either the infotainment controls or the touch screen in the Colour-Info-Display.
Instruments and controls Turning a function on or off 1. Turn the TUNE/MENU knob to highlight the function. 2. Press the TUNE/MENU knob to turn the function on or off. A checkmark next to the function indicates that the function is on. Using the touch screen Use the touch screen icons and menus on the Colour-Info-Display to select personalisation features. { = Touch to scroll up. } = Touch to scroll down. Back: Touch Back in the upper right corner of the display to return to the previous menu.
84 Instruments and controls Auto fan speed Auto fan speed sets the automatic fan speed to maintain the desired interior temperature. Choose a blower setting: High: Increased speed. Medium: Moderate speed. Low: Reduced speed. To select the Auto fan speed: 1. Press the vehicle menu. 2. Select Climate and air quality. 3. Select Auto fan speed. 4. Select the fan speed. 5. Press Back to return to the previous menu.
Instruments and controls 3. Select the temperature level. 4. Press Back to return to the previous menu. Engine Assisted Heating (Plugged‐ In) This feature will enable or disable Engine Assisted Heating whenever the vehicle is plugged in. A change in setting will not take affect until after the vehicle is first powered down. To turn Engine Assisted Heating (Plugged‐In) on or off: 1. Press the vehicle menu. 2. Select Climate and air quality. 3. Turn Engine Assisted Heating (Plugged‐In) on or off. 4.
86 Instruments and controls 3. Turn Charging Power Loss Alert on or off. 4. Press Back to return to the previous menu. Personalization by driver This allows the radio to store favourites by driver: 1. Press the vehicle menu. 2. Select Comfort & Convenience. 3. Turn Personalization by driver on or off. 4. Press Back to return to the previous menu. Languages This allows selection of the desired language. To select the language: 1. Press the vehicle menu. 2. Select Languages. 3.
Instruments and controls Auto door unlock This allows selection of which doors will automatically unlock when the vehicle is shifted into P. The available options are: ■ All doors ■ Driver door ■ Off To select how the doors will automatically unlock: 1. Press the vehicle menu. 2. Select Power door locks. 3. Select Auto door unlock. 4. Select how the doors will automatically unlock. 5. Press Back to return to the previous menu.
88 Instruments and controls To select remote lock feedback: 1. Press the vehicle menu. 2. Select Remote Lock / Unlock / Start. 3. Select Remote lock feedback. 4. Select the remote feedback. 5. Press Back to return to the previous menu. Exterior lighting by unlocking When on, the exterior lights will flash when unlocking the vehicle with the radio remote control. To turn Exterior lighting by unlocking on or off: 1. Press the vehicle menu. 2. Select Remote Lock / Unlock / Start. 3.
Instruments and controls 4. Select which doors to unlock. 5. Press Back to return to the previous menu. Passive door lock This allows passive locking to be turned on or off and select what type of feedback. The available options are: ■ Off ■ On ■ ON with Active Chirp To select how the doors will unlock: 1. Press the vehicle menu. 2. Select Remote Lock / Unlock / Start. 3. Select Passive door lock. 4. Select On, Off or ON with Active Chirp. 5. Press Back to return to the previous menu.
90 Lighting Lighting Exterior lighting Automatic light control Light switch Automatic light control function Exterior lighting ............................ 90 Interior lighting ............................. 93 Lighting features .......................... 94 Turn adjuster wheel S: AUTO = automatic light control: exterior lighting is switched on and off automatically depending on external lighting conditions. m = exterior lighting is switched off.
Lighting Note Do not cover the light sensor otherwise the AUTO mode will not operate properly. Headlight range adjustment 91 Hazard warning flashers Automatic headlight activation During poor lighting conditions the headlights are switched on. Tunnel detection When a tunnel is entered, the headlights are switched on. High beam To switch from low to high beam, push the turn signal lever. To switch to low beam, push lever again or pull.
92 Lighting Turn and lane-change signals lever up = right turn signal lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel moves back, the turn signal is automatically deactivated. For three flashes, e.g. when changing lanes, press the lever until resistance is felt and then release. Switch the turn signal off manually by moving the lever to its original position. Turn signal control indicator 3 61.
Lighting Interior lighting 93 Dome lights Front reading lights The dome light controls are located in the overhead console. To operate, press the following buttons: Press w = automatic switching on and off Press u = on Press v = off The front reading lights are located in the overhead console.
94 Lighting The rear reading lights are located in the headliner. Lighting features Entry lighting Headlights, taillights, reversing lights, sidelights and the interior lights turn on briefly by pressing ( on the radio remote control. The lights turn off immediately when the m button is pressed or automatically after a brief period. Exit lighting The headlights, parking lights, tail lights, reverse light and the number plate lights come on by doing the following: 1. Switch off ignition. 2.
Climate control Climate control Climate control systems ............... 95 Air vents ..................................... 100 Maintenance .............................. 100 Climate control systems Automatic climate control system Note The vehicle may require the use of an auxiliary heat source under certain cold conditions. This provides additional heating and defrost capability obtained by running the engine, even if the high voltage battery is adequately charged.
96 E F G H I J K Climate control = = = = = = = Outside air temperature display Climate modes Climate power gauge Manual fan control Temperature setting display Air conditioning indicator Heat status indicator Climate control touch screen The climate mode, fan, air delivery, recirculation and auto heated seats are controlled by pressing the CLIMATE button on the instrument panel and viewing information in the Colour-Info-Display.
Climate control Climate power gauge When the climate mode is changed, the climate power gauge displays the impact that the changes have on energy use. The higher the reading, the more energy is being used. Air conditioning / Heat status indicators Air conditioning / Electric heating Air conditioning and electric heating could be on at the same time when dehumidifying is required in ECO or Comfort modes.
98 Climate control Manual operation Fan control Press the fan control buttons x on the instrument panel or the touch screen fan control, to increase or decrease the fan speed. The fan speed setting is displayed. Press AUTO to return to automatic operation. To turn the fan or climate control system off, press the fan down button repeatedly. If the fan is manually turned off while in ECO or Comfort mode, the display will automatically change to Fan Only mode.
Climate control Manual recirculation Press 4 to recirculate air inside the vehicle, press it again to select outside air. When selected, the touch screen button lights up to indicate that air is being recirculated. This helps to quickly cool the air inside the vehicle or prevent outside air and odours from entering. Pressing 4 cancels automatic recirculation. Press AUTO or AUTO 4 to return to automatic operation; recirculation runs automatically as needed.
100 Climate control Air vents Maintenance Use the slats on the air vents to change the direction of the airflow. Use the thumbwheels near each vent to open and close off the airflow. Air intake 9 Warning Do not attach any objects to the slats of the air vents. Risk of damage and injury in case of an accident. The air intake in front of the windscreen in the engine compartment must be kept clear to allow air intake. Remove any leaves, dirt or snow.
Driving and operating Driving and operating Driving hints Driving economically Driving hints ............................... 101 Starting and operating ............... 102 Electric vehicle operation modes ........................................ 106 Engine exhaust .......................... 111 Electric drive unit ....................... 111 Brakes ........................................ 113 Ride control systems ................. 116 Driver assistance systems ......... 118 Charging .....................
102 Driving and operating Vehicle charging / maintenance Charging Keep the vehicle plugged in, even when fully charged, to keep the battery temperature ready for the next drive. This is important when outside temperatures are extremely hot or cold. Maintenance Always keep the tyres properly inflated and the vehicle properly aligned. The weight of excess cargo in the vehicle affects efficiency and range. Avoid carrying more than is needed.
Driving and operating button light is on steady when the ignition is on. When the ignition is switched off, the m button light will also turn off.1) The radio remote control must be in the vehicle for the system to operate. If the vehicle will not start, place the mechanical key of the radio remote control inside the transmitter slot located in the instrument panel storage compartment. Starting and stopping the vehicle 3 104.
104 Driving and operating If the vehicle must be shut off in an emergency: 9 Warning Switching off the ignition while moving may disable the airbags. While driving, only shut the propulsion system off in an emergency. 1. Brake using a firm and steady pressure. Do not pump the brakes repeatedly. This may deplete power assist, requiring increased brake pedal force. 2. Shift the vehicle to N. This can be done while the vehicle is moving.
Driving and operating A welcome, ready, and goodbye audio message will be heard in the vehicle and animated on the instrument cluster when opening the driver's door upon entry, when the vehicle is ready to be driven and when the ignition is switched off. The instrument cluster displays an active fuel or battery gauge, along with an audio start-up cue, when the vehicle is ready to be driven. This could take up to 15 seconds at extremely cold temperatures. The engine will only start if needed.
106 Driving and operating Parking ■ Do not park the vehicle on an easily ignitable surface. Things that can burn could touch hot exhaust parts under the vehicle and ignite. ■ Always apply the electrical parking brake. Pull switch m. ■ Switch off the ignition. Turn the steering wheel until the steering wheel lock engages. ■ If the vehicle is on a level surface or uphill slope, set the parking brake and then shift the selector lever to P before switching off the ignition.
Driving and operating vehicle can be plugged in to recharge the high voltage battery and restore electric mode. The high voltage battery will continue to provide some power and work together with the engine to provide peak performance when it is required, such as driving up a steep incline or for high acceleration manoeuvres. The battery will not be charged nor will electric vehicle range be restored by the engine.
108 Driving and operating If in Sport, Mountain or Hold mode, the mode may become unavailable and the vehicle will return to Normal mode. The indicator light goes off and a DIC message displays. Driver Information Centre (DIC) 3 67. Control indicator Sport3 64. Mountain mode Sport mode Sport mode provides more responsive acceleration than Normal mode, but can reduce efficiency. Use Normal mode whenever possible. Press DRIVE MODE to select Sport mode.
Driving and operating Each time the vehicle is started, it will return to Normal mode to maintain a smaller battery charge reserve for normal driving. Control indicator Mountain 3 64. Hold mode Hold mode is only available when the vehicle is in electric mode. This mode places the remaining battery charge into a reserve for the driver to use as desired. Selecting this mode transitions the vehicle to extended range mode to maintain the battery charge reserve.
110 Driving and operating If the engine maintenance mode request was delayed for one day, it will automatically start the engine at the next vehicle start. An engine maintenance mode notification screen will appear in the Colour-InfoDisplay. reduced, or no power. An adequate fuel level must be maintained in the vehicle to keep it operational. maximise the length of time before another fuel maintenance mode is needed. During fuel maintenance mode the engine may turn on and off.
Driving and operating If the fuel maintenance mode request was delayed for one day, it will start at the next vehicle start and display the fuel maintenance mode notification screen on the Colour-Info-Display. If fuel maintenance mode is required and the fuel level is low, fuel maintenance mode may eventually empty the fuel tank if fuel is not added. This will result in reduced, or no power. An adequate fuel level must be maintained in the vehicle to keep it operational.
112 Driving and operating 9 Warning It is dangerous to get out of the vehicle if the shift lever is not fully in P with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the propulsion system is running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P.
Driving and operating Note Spinning the tyres or holding the vehicle in one place on a hill using only the accelerator pedal may damage the electric drive unit. If you are stuck, do not spin the tyres. When stopping on a hill, use the brakes to hold the vehicle in place. Brakes Antilock brake system Antilock brake system (ABS) prevents the wheels from locking. ABS starts to regulate brake pressure as soon as a wheel shows a tendency to lock. The vehicle remains steerable, even during hard braking.
114 Driving and operating Parking brake Electrical parking brake The electrical parking brake can always be activated, even if the ignition is off. To prevent draining of the 12 volt battery, avoid repeated cycles of the electrical parking brake system when the ignition is off. In case of insufficient electrical power, the electrical parking brake cannot be applied or released. Before leaving the vehicle, check the control indicator m to ensure the parking brake is applied.
Driving and operating If the electrical parking brake fails to apply, the rear wheels should be blocked to prevent vehicle movement. For maximum electrical parking brake force when parking on a hill, pull the electrical parking brake switch twice. Electrical parking brake release To release the electrical parking brake, switch the ignition on, apply and hold the brake pedal and push down momentarily on the m switch.
116 Driving and operating In the event of a controller problem, the brake pedal may be harder to push and the stopping distance may be longer. Driver Information Centre (DIC) 3 67. Ride control systems Traction Control system The Traction Control system (TC) is a component of the Electronic Stability Control. TC improves driving stability when necessary, regardless of the type of road surface or tyre grip, by preventing the drive wheels from spinning.
Driving and operating Control indicator k illuminates and a message in the Driver Information Centre (DIC) is displayed. TC is reactivated by pressing the b button again. TC is also reactivated the next time the ignition is switched on. Fault If there is a problem detected with TC, a message is displayed on the DIC. When this message is displayed and b illuminates, the vehicle is safe to drive but the system is not operational. Driving should be adjusted accordingly.
118 Driving and operating depressed until k and n illuminate and a message in the Driver Information Centre (DIC) is displayed. ESC is reactivated by pressing the b button again. If cruise control is being used when ESC activates, cruise control will automatically disengage. Press the cruise control button to re-engage when road conditions allow. Cruise control 3 118. Driver Information Centre (DIC) 3 67. Fault If there is a problem detected with ESC, a message is displayed on the DIC.
Driving and operating SET/- (Set/Coast): Move the thumbwheel down to set a speed and activate cruise control or to make the vehicle decelerate. Setting cruise control The cruise control buttons are on the steering wheel. m (On/Off): Press to turn the cruise control system on and off. An indicator light will turn on or off in the instrument cluster. y (Cancel): Press to disengage cruise control without erasing the set speed from memory.
120 Driving and operating Reducing speed If the cruise control system is already activated: ■ Move the thumbwheel toward SET/ − and hold until the desired lower speed is reached, then release it. ■ To slow down in very small amounts, move the thumbwheel toward SET/− briefly. Each time this is done, the vehicle goes about 1 mph slower. Passing another vehicle Use the accelerator pedal to increase vehicle speed.
Driving and operating When the vehicle is in R, the system may be active. If the vehicle is in a car wash, the sensors may detect objects in the car wash. High-toned beeps from the front speakers are for objects detected near the front bumper. Low-toned beeps from the rear speakers are for objects detected near the rear bumper. The interval between the beeps becomes shorter as the vehicle gets closer to the obstacle. When the distance is less than 12 inch the beeping is a continuous tone for five seconds.
122 Driving and operating ■ An object was hanging out of the tailgate during the last drive cycle. Once the object is removed, ultrasonic parking assist will return to normal operation. ■ An object or cover is attached to the front of the vehicle. ■ The bumper is damaged. Take the vehicle to a workshop to repair the system. ■ Other conditions, such as vibrations from a jackhammer or the compression of air brakes on a very large truck, are affecting system performance.
Driving and operating Rear view camera 9 Warning The rear view camera system does not display pedestrians, bicyclists, animals or any other object located outside the camera's field of view, below the bumper or under the vehicle. Do not back the vehicle using only the rear view camera screen or by using the screen during longer, higher speed backing manoeuvres or where there could be cross-traffic. Perceived distances may be different from actual distances.
124 Driving and operating Guidelines The rear view camera system has a guideline overlay that can help the driver align the vehicle when backing into a parking spot. To turn the guidelines on or off: 1. Shift into P. 2. Press the CONFIG button on the instrument panel. 3. Select display. 4. Select guidelines. When a checkmark appears next to guidelines, guidelines will appear. Rear view camera location The rear view camera is located above the number plate. The area displayed by the camera is limited.
Driving and operating Charging This section explains the process for charging the vehicle's high voltage battery. Do not allow the vehicle to remain in temperature extremes for long periods without being driven or plugged in. It is recommended that the vehicle be plugged in when temperatures are below 0°C and above 32°C to maximise high voltage battery life. The charging system may run fans and pumps that result in sounds from the vehicle while it is turned off.
126 Driving and operating End charge charge level. The charge level selection can be done either by using the charging screen in the Colour-Info-Display or by using the charge level button on the charge cord, depending on the car model. 1. Unlock the vehicle with the radio remote control to disarm the charge cord theft alert. 9 Warning Using a charge level that exceeds the electrical circuit or AC outlet capacity may start a fire or damage the electrical circuit.
Driving and operating compartment. The vehicle plug (B) should be on the right side of the charge cord. 7. Push the charge cord handle down until it locks into the handle clip at the rear of the storage compartment. 127 Charging status Programmed charging override 6.
128 Driving and operating ■ Long flashing green – Two horn chirps: Vehicle is plugged in. Battery is not fully charged. Battery charging is delayed. ■ Short flashing green – No horn chirp: Vehicle is plugged in. Battery is fully charged. ■ Solid yellow – No horn chirp: Vehicle is plugged in. It is normal for the charging status indicator to turn yellow for a few seconds after plugging in a compatible charge cord. Otherwise, the charging system has detected a fault and will not charge the battery.
Driving and operating 9 Warning Using the charge cord with a worn or damaged AC outlet may cause burns or start a fire. Periodically, check the AC wall plug and charge cord while the vehicle is charging. If the AC wall plug feels hot, unplug the charge cord and have the AC outlet replaced by a qualified electrician. Replace the charge cord if the AC wall plug or cord are damaged. Do not use an AC outlet that is worn or damaged. 9 Warning An extension cord should not be used to charge the vehicle.
130 Driving and operating A portable charge cord used to charge the vehicle high voltage battery is stored under the load compartment. The charge cord used to charge the vehicle is a high‐powered electrical device. During normal operation, the AC wall plug of the charge cord may feel warm. The AC wall plug must fit tightly into an AC outlet that is in good condition. Charge cord status indicators The charge cord status indicators illuminate green or flash red to identify the charge cord status.
Driving and operating The charge level cannot be changed when the vehicle plug is plugged into the charge port on the vehicle. If the charge level button is pressed while the vehicle plug is plugged into the charge port on the vehicle, the charge level indicators will flash briefly. To change the charge level, unplug the vehicle plug from the charge port on the vehicle and select the desired charge level. Normal level: This level is recommended. All four charge level indicators will be lit.
132 Driving and operating Fuel Caution Fuel for petrol engines Only use unleaded fuel that complies with EN 228. Usage of fuel with quality, not complying to the Technical Regulations can lead to engine damage and loss of all warranty obligations. Equivalent standardised fuels with an ethanol content of max. 10 % by volume may be used. In this case only use fuel that complies with E DIN 51626-1. Use fuel with the recommended octane rating 3 183.
Driving and operating 1. Press the fuel door button on the driver door for one second. A message displays on the Driver Information Centre (DIC) to wait. passenger side will unlock. Push the rearward edge of the fuel door in and release to open the door. 3. Turn the fuel cap counterclockwise to remove. While refuelling, hang the fuel cap tether from the hook on the inside of the fuel door. Complete refuelling within 30 minutes of pushing the fuel door button found on the driver side door.
134 Driving and operating The specification of CO2 emission is also a constituent of the directive. The figures given must not be taken as a guarantee for the actual fuel consumption of a particular vehicle. Furthermore, fuel consumption is dependent on personal driving style as well as road and traffic conditions. All values are based on the EU base model with standard equipment.
Vehicle care Vehicle care General Information ................... 135 Vehicle checks ........................... 137 Bulb replacement ....................... 143 Electrical system ........................ 146 Wheels and tyres ....................... 156 Jump starting ............................. 168 Towing ....................................... 172 Appearance care .......................
136 Vehicle care When lifting the vehicle from the front, place the service jack directly under the cradle mount. Ramps may be needed under the front tyres to provide the necessary clearance for certain service jacks in this location. The front lifting points can be accessed from either side of the vehicle, behind the front tyres. The rear lifting points can be accessed from either side of the vehicle, in front of the rear tyres.
Vehicle care Vehicle checks Performing work 9 Danger Never try to do your own service on high voltage battery components. You can be injured and the vehicle can be damaged if you try to do your own service work. Service and repair of these high voltage battery components should only be performed by a trained service technician with the proper knowledge and tools. Exposure to high voltage can cause shock, burns, and even death.
138 Vehicle care Engine oil Check the engine oil manually on a regular basis to prevent damage to the engine. Ensure that the correct specification of oil is used. Recommended fluids and lubricants 3 177. Check with the vehicle on a level surface. The engine must be at operating temperature and switched off for at least 5 minutes. Pull out the dipstick, wipe it clean, insert it to the stop on the handle, pull out and read the engine oil level.
Vehicle care Caution Only use approved antifreeze. If the engine cooling system is cold, the coolant level should be above the filling line mark. Top up if the level is low. 9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly. High voltage battery cooling system 9 Danger The high voltage battery coolant may only be serviced by a qualified technician. Improper handling could cause serious injuries or death.
140 Vehicle care Check to see if coolant is visible in the power electronics and charger modules coolant reservoir. If coolant is visible but the coolant level is below the cold fill line, there could be a leak in the cooling system. The power electronics and charger modules cooling system in the vehicle is filled with a 1:1 mixture of approved coolant concentrate and deionised water. Engine overheating The vehicle has an indicator to warn of engine overheating.
Vehicle care Only use high-performance brake fluid approved for the vehicle, consult a workshop. Brake fluid 3 177. Battery 9 Danger With the vehicle not running for at least one minute, the maximum fluid level (A) is at the top of the reservoir body. With the vehicle running, the fluid level should be in the proper operating range (B) between the MIN and MAX marks. If it is not, have the brake hydraulic system checked to see if there is a leak.
142 Vehicle care charger. If available, use the AGM setting on the charger, to limit charge voltage to 14,8 volts. Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point. Vehicle storage In addition, to avoid potential damage to the high voltage battery, perform the following recommended steps: ■ Store the high voltage battery with 1/2 charge or less. ■ Always store the vehicle in an environment between −10°C and 30°C.
Vehicle care Headlight aiming Headlight aim has been preset and should need no further adjustment. When driving in countries where the traffic drives on the opposite side of the road, it is not necessary to adjust the headlights. If the vehicle is damaged in a crash, the headlight aim may be affected. If adjustment to the headlights is necessary, seek the assistance of a workshop. Bulb replacement Halogen headlights Switch off the ignition and switch off the relevant switch or close the doors.
144 Vehicle care Passenger side headlights To replace the high/low‐beam headlight: Tail lights Have the lights replaced by a workshop. Side turn signal lights Have bulbs replaced by a workshop. Reversing light 1. Remove the cover from the back of the headlight assembly by turning it counterclockwise. 2. Remove the bulb from the headlight assembly by turning it counterclockwise. 3. Disconnect the bulb from the wiring harness connector. 4.
Vehicle care Number plate light 1. Press the spring clip on the right end of the light assembly to the left to unlock the light assembly. 2. Pull down on the light assembly to remove it from the fascia. 3. Turn the bulb socket (A) counterclockwise to remove it from the light assembly (C). 4. Pull the bulb (B) straight out of the bulb socket (A). 5. Push the replacement bulb straight into the bulb socket (A) and turn the bulb socket (A) clockwise to install it into the light assembly (C). 6.
146 Vehicle care 6. Reinstall the bulb socket by lining up the tabs and turn it clockwise to lock it into place. 7. Replace the three inboard screws into the aero panel. Electrical system High voltage devices and wiring 9 Warning Exposure to high voltage can cause shock, burns, and even death. The high voltage components in the vehicle can only be serviced by technicians with special training. High voltage components are identified by labels. Do not remove, open, take apart, or modify these components.
Vehicle care Windscreen wipers If the wiper motor overheats due to heavy snow or ice, the windscreen wipers will stop until the motor cools and the wiper control is turned off. After removal of the blockage, the wiper motor will restart when the control is then moved to the desired operating position. Although the circuit is protected from electrical overload, overload due to heavy snow or ice, may cause wiper linkage damage.
148 Vehicle care Engine compartment fuse box Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse. The fuse box is in the front left of the engine compartment. To open the fuse block cover, press the clips at the front and back and rotate the cover up to the side.
Vehicle care 149 Mini fuses Usage Mini fuses Usage 1 Engine control module – switched power 14 Theft deterrent — Power sounder 2 Emissions 15 3 – 4 Ignition coils / Injectors Traction power inverter module and transmission control module — Battery 5 Column lock 17 Engine control module — Battery 6a – 22 Left high‐beam headlight 6b – 24 – 7 – 25 – 8 – 26 Theft deterrent — Horn 9 Heated mirrors 31 – 10 Air conditioning control module 32 11 Traction power inverter mo
150 Vehicle care Mini fuses Usage Mini fuses Usage Mini fuses Usage 33 46 – 53 47 – Traction power inverter module — Run/Crank 49 – 54 50 Run/Crank — Rear view camera, accessory power module, tyre pressure monitor, headlight levelling motors Run/Crank — Fuel system control module, air conditioning control module, on‐board charger Run/Crank — Vehicle integration control module 34 Vehicle integration control module — Battery 35 – 36 Power electronics coolant pump 37 Cabin heater cont
Vehicle care 151 J-case fuses Usage Micro relays Usage Instrument panel fuse box 30 1 – 2 – Instrument panel fuse box on the left side end 6 – 8 – 10 – Antilock brake system motor 42 Right cooling fan 43 Front wipers 44 Charger 45 – 48 Left cooling fan Mini relays Usage 3 Powertrain 4 Heated mirrors 7 – 9 – 11 – 12 – 13 – 14 Run/Crank Ultra-micro relays Usage 5 Charge port door After having changed defective fuses, close the fuse box cover and press until it
152 Vehicle care Fuses Usage Fuses Usage F1 Power outlet – Top of IP storage bin F10 F2 Radio F3 Instrument cluster (left hand drive) F4 Infotainment display F5 Heating, ventilation & air conditioning/ Integrated centre stack switches Body control module 1/Body control module electronics/ Remote entry/Power moding/ Centre high‐ mounted stoplight/ Number plate lights/Left daytime running light/Left position lights/ Tailgate release relay control/ Washer pump relay control/Switch indicator light
Vehicle care 153 Relays Usage Fuses Usage R1 Retained accessory power relay for power outlets F1 Steering wheel switch backlighting R2 – F2 R3 – Column lock (right hand drive) R4 Deadbolt (left hand drive), Child lockout (right hand drive) F3 Cluster (right hand drive) F4 Body control module 3/Right headlight F5 Body control module 2/Body control module electronics/ Tail light/Right daytime running light/ Shifter lock/ Switch backlighting/Rear fog light F6 Body control module 5/ Retai
154 Vehicle care Fuses Usage Relays Usage F8 R1 – R2 – R3 – R4 Deadbolt (right hand drive), Child lockout (left hand drive) Body control module 7/Left front turn signal/Right rear stop and turn signal light/ Child security lock relay control F9 Body control module 8/Locks F10 Right secondary data link connector (left hand drive), Right primary data link connector (right hand drive) F11 Intrusion and inclination sensor F12 Blower motor (left hand drive) F13 – F14 – F15 – F16 – F
Vehicle care Fuses Usage Fuses Usage Diodes Usage F1 – F12 Rear power windows DIODE – F2 Fuel system control module F13 Electrical parking brake F3 Passive start/ Passive entry module F14 Rear defog (Upper grid) F4 Heated seats F15 – F5 Driver door switches (Outside rearview mirror/ Charge port door release/ Refuel request/Driver window switch) F16 Tailgate release F17 – F18 – F6 Fuel (Diurnal valve and evap.
156 Vehicle care Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage. Seek the assistance of a workshop in the event of damage or unusual wear. Tyres Directional tyres Fit directional tyres such that they roll in the direction of travel. The rolling direction is indicated by a symbol (e.g.
Vehicle care Unscrew the valve cap. The tyre and loading information label on the front left centre B-pillar indicates the original equipment tyres and the correct cold tyre inflation pressures. Additional to that: See tyre pressure 3 185. The tyre pressure data refers to cold tyres. It applies to summer and winter tyres. The ECO tyre pressure serves to achieve the smallest amount of fuel consumption possible.
158 Vehicle care Please note that the tyre pressure monitoring system is not a substitute for proper tyre maintenance and it is the driver's responsibility to maintain correct tyre pressure, even if under‐ inflation has not reached the level to trigger illumination of the tyre pressure monitoring system low tyre pressure telltale. The tyre pressure monitoring system malfunction indicator is combined with the low tyre pressure telltale.
Vehicle care If the tyre pressure shall be reduced, switch off ignition before reducing. Sensor matching process Manual Each tyre pressure monitoring system sensor has a unique identification code. The identification code needs to be matched to a new tyre/wheel position after rotating the vehicle’s tyres or replacing one or more of the sensors.
160 Vehicle care 10. Proceed to the right rear tyre and repeat the procedure in Step 8. 11. Proceed to the left rear tyre and repeat the procedure in Step 8. The horn sounds two times to indicate the sensor identification code has been matched to the left rear tyre and the tyre pressure monitoring system sensor matching process is no longer active. The message on the DIC display screen goes off. 12. Switch off the ignition. 13. Set all four tyres to the recommended air pressure level.
Vehicle care ■ Replacement tyres or wheels do not match the original equipment tyres or wheels. Tyres and wheels other than those recommended could prevent the tyre pressure monitoring system from functioning properly. ■ Operating electronic devices or being near facilities using radio wave frequencies similar to the tyre pressure monitoring system could cause the tyre pressure monitoring system sensors to malfunction.
162 Vehicle care Wheel covers Tyre chains Wheel covers and tyres that are factory approved for the respective vehicle and comply with all of the relevant wheel and tyre combination requirements must be used. If the wheel covers and tyres used are not factory approved, the tyres must not have a rim protection ridge. Wheel covers must not impair brake cooling. Tyre repair kit 9 Warning Use of unsuitable tyres or wheel covers could lead to sudden pressure loss and thereby accidents.
Vehicle care D E F G H = = = = = Pressure deflation button Tyre sealant canister Sealant/Air hose (clear) Air only hose (black) Power plug If you have a flat tyre: Move the shift lever to P. The tyre repair kit is under a cover in the load compartment. A = Selector switch (Sealant/Air or Air only) B = On/Off button C = Pressure gauge Note The driving characteristics of the repaired tyre is severely affected, therefore have this tyre replaced.
164 Vehicle care When using the tyre repair kit during cold temperatures, warm the kit in a heated environment for five minutes. This will help to inflate the tyre faster. If a tyre goes flat, avoid further tyre and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. Hazard warning flashers 3 91. Do not remove any objects that have penetrated the tyre. 1. Take the tyre repair kit from the compartment. 2. Unwrap the sealant/air hose (F) and the power plug (H). 3.
Vehicle care 10. Inflate the tyre to the recommended inflation pressure using the pressure gauge (C). Tyre and loading information label 3 156. Tyre pressures 3 185. The pressure gauge (C) may read higher than the actual tyre pressure while the compressor is on. Turn the compressor off to get an accurate pressure reading. The compressor may be turned on/off until the correct pressure is reached.
166 Vehicle care 19. Stop at a safe location and check the tyre pressure. Refer to steps 1 through 11 under using the tyre repair kit without sealant to inflate a tyre (Not Punctured). If the tyre pressure has fallen more than 0.7 bar below the recommended inflation pressure, stop driving the vehicle. The tyre is too severely damaged and the tyre sealant cannot seal the tyre. If the tyre pressure has not dropped more than 0.
Vehicle care Hazard warning flashers 3 91. 1. Take the tyre repair kit from the compartment. 2. Unwrap the air only hose (G) and the power plug (H). 3. Place the kit on the ground. Make sure the tyre valve stem is positioned close to the ground so the hose will reach it. 4. Remove the tyre valve stem cap from the flat tyre by turning it counterclockwise. 5. Attach the air only hose (G) onto the tyre valve stem by turning it clockwise until it is tight. 6.
168 Vehicle care 4. Replace with a new canister which is available from a workshop. 5. Push the new canister into place. The tyre repair kit has an accessory adapter located in a compartment on the bottom of its housing that may be used to inflate air mattresses, balls, etc. Removal and installation of the sealant canister To remove the sealant canister: 1. Unwrap the sealant hose. 2. Press the canister release button. 3. Pull up and remove the canister.
Vehicle care 9 Warning Be extremely careful when starting with jump leads. Any deviation from the following instructions can lead to injuries or damage caused by battery explosion or damage to the electrical systems of both vehicles. 9 Warning Avoid contact of the battery with eyes, skin, fabrics and painted surfaces. The fluid contains sulphuric acid which can cause injuries and damage in the event of direct contact.
170 Vehicle care 6. Check that the jumper cables do not have loose or missing insulation or a shock could result and the vehicles could be damaged. Before connecting the jumper cables, here are some basic things to know. Positive (+) jumper cable goes to positive (+) battery terminal or a remote positive (+) terminal if available. Negative (−) jumper cable goes to negative (−) battery terminal or a remote negative (−) terminal if available.
Vehicle care 2. Park both vehicles close enough so that the jumper cables can reach both vehicles' positive (+) and negative (−) terminals. The vehicles must not touch each other. It could cause an unwanted ground connection that could damage both vehicles' electrical systems. Put both vehicles in P for an automatic transmission or electric drive unit. For a manual transmission, place the vehicle in neutral and apply the parking brake. 3. Turn off both vehicles.
172 Vehicle care 2. Connect the other end of the red positive (+) jumper cable to the positive (+) battery terminal of the vehicle. 3. Connect the black negative (−) jumper cable to the negative (−) battery terminal of the vehicle. Do not let the other end touch anything until the next step. 4. Make the final connection to a heavy, unpainted metal engine part or to the remote negative (−) terminal on the other vehicle with the run‐down battery. 5. Press m to start the vehicle.
Vehicle care Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only when absolutely necessary, as this has a degreasing effect and impairs lock function. After using de-icing agent, have the locks regreased by a workshop. Washing The paintwork of your vehicle is exposed to environmental influences. Wash and wax your vehicle regularly. When using automatic vehicle washes, select a programme that includes waxing.
174 Vehicle care For mechanical removal of ice, use a sharp-edged ice scraper. Press the scraper firmly against the glass so that no dirt can get under it and scratch the glass. Clean smearing wiper blades with a soft cloth and window cleaner. Wheels and tyres Do not use high-pressure jet cleaners. Clean rims with a pH-neutral wheel cleaner. Rims are painted and can be treated with the same agents as the body. The front air deflector allows air to flow cleaner under the vehicle.
Vehicle care Caution Close Velcro fasteners as open Velcro fasteners on clothing could damage seat upholstery. The same applies to clothing with sharp-edged objects, like zips or belts or studded jeans. Plastic and rubber parts Plastic and rubber parts can be cleaned with the same cleaner as used to clean the body. Use interior cleaner if necessary. Do not use any other agent. Avoid solvents and petrol in particular. Do not use highpressure jet cleaners.
176 Service and maintenance Service and maintenance General information ................... 176 Recommended fluids, lubricants and parts .................................... 177 General information Service information In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified.
Service and maintenance Recommended fluids, lubricants and parts Recommended fluids and lubricants Only use products that have been tested and approved. Damage resulting from the use of nonapproved materials will not be covered by the warranty. 9 Warning Operating materials are hazardous and could be poisonous. Handle with care. Pay attention to information given on the containers. Engine oil Engine oil is identified by its quality and its viscosity.
178 Service and maintenance Coolant and antifreeze Use only silicate-free long life coolant (LLC) antifreeze approved for the vehicle, consult a workshop. The system is factory filled with coolant designed for excellent corrosion protection and frost protection down to approx. -28 °C. This concentration should be maintained all year round. The use of additional coolant additives that intend to give additional corrosion protection or seal against minor leaks can cause function problems.
Technical data Technical data Vehicle identification .................. 179 Vehicle data ............................... 180 Vehicle identification Vehicle Identification Number 179 Engine identification The eighth character in the VIN is the engine code. This code identifies the vehicle's engine, specifications, and replacement parts. Service Parts identification label The Vehicle Identification Number (VIN) is located in the left front corner of the instrument panel.
180 Technical data Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries (except Belarus, Moldova, Russia, Serbia, Turkey) Engine oil quality Only Israel Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (including CNG, LPG, E85) Diesel engines dexos 1 – – ✔ – dexos 2 ✔ ✔ – ✔ In case dexos quality is unavailable you may use max. 1 litre engine oil quality ACEA C3 once between each oil change.
Technical data 181 International service schedule Required engine oil quality All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (including CNG, LPG, E85) Diesel engines dexos 1 ✔ – – – dexos 2 – ✔ ✔ ✔ In case dexos quality is unavailable you may use the oil qualities listed below: All countries outside Europe except Israel Engine oil quality Only Belarus, Moldov
182 Technical data All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (including CNG, LPG, E85) Diesel engines ACEA A3/B3 ✔ – ✔ – ACEA A3/B4 ✔ ✔ ✔ ✔ ACEA C3 ✔ ✔ ✔ ✔ API SM ✔ – ✔ – API SN ✔ – ✔ – Engine oil viscosity grades All countries outside Europe (except Israel), including Belarus, Moldova, Russia, Serbia, Turkey Ambient temperature Petrol and
Technical data Engine data Engine A14XFL Petrol Electric motor Number of cylinders 4 - Piston displacement [cm3] 1398 - Power (Engine/Electric motor) [kW] 63 111 at rpm 4800 5000 Torque [Nm] 126 370 at rpm 4250 250-2800 Fuel type Petrol - recommended 95 - possible 98 - Octane rating RON 183
184 Technical data Performance A14XFL Petrol Electric motor Maximum speed1) [mph] 100 mph Vehicle weight Kerb weight [kg] 1735 Vehicle dimensions Length [mm] 4498 Width [mm] 1787 Height (unladen) [mm] 1439 Wheelbase [mm] 2685 1) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle.
Technical data 185 Capacities Engine oil Engine A14XFL including Filter [l] 3,5 between MIN and MAX [l] 1 Fuel tank Petrol, nominal capacity [l] 35,2 Tyre pressures Tyres Comfort with up to 3 people ECO with up to 3 people With full load front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 240/2.4 (35) 240/2.4 (35) 270/2.7 (39) 270/2.7 (39) 250/2.5 (36) 290/2.9 (42) 225/45 R182) 260/2.
186 Customer information Customer information Customer information Service network Customer information ................ 186 Vehicle data recording and privacy ....................................... 187 Open source information This vehicle contains open source software, including without limitation, software distributed and/ or modified under the GNU General Public License, Version 2, June 1991 and the GNU Lesser General Public License, Version 2.1, February 1999. See www.oss.gm.
Customer information ■ Greece: 00800 331 52 963 ■ Hungary: 0680204997 ■ Ireland: 1800 812 450 ■ Italy: 800089741 ■ Luxembourg: 800 40004 ■ Netherlands: 0800 020 5915 ■ Norway: 800 62072 ■ Poland: 00800 331 1407 ■ Romania: 0800 801020 ■ Slovakia: 800 116 981 ■ Spain: 900 900 428 ■ Sweden: 020 120 3022 ■ Switzerland: 0800 455565 ■ United Kingdom: 0800 0260275 187 Vehicle data recording and privacy Event data recorders The vehicle has a number of sophisticated systems that monitor and control several vehicl
188 Customer information service history of the vehicle. This enables the workshop to offer you efficient maintenance and repair, tailored to your individual vehicle, each time you bring it back to the workshop.
Customer information 189
190 Index A Accessories and vehicle modifications .......................... 135 Airbag and belt tensioners ........... 61 Airbag deactivation ................ 42, 62 Airbag system .............................. 40 Air intake .................................... 100 Air vents ..................................... 100 Antilock brake system ................ 113 Antilock brake system (ABS) ....... 63 Anti-theft alarm system ................ 27 Anti-theft locking system ..............
191 Driving economically................... 101 Driving efficiency gauge............... 58 E Electric adjustment ...................... 28 Electrical parking brake................ 63 Electrical parking brake fault........ 63 Electrical requirements............... 131 Electrical system overload ......... 146 Electric drive unit.......................... 15 Electric mode.............................. 106 Electric vehicle operation modes.. 16 Electronic Stability Control..........
192 M Maintenance modes................... 109 Malfunction indicator light ............ 62 Mirror adjustment ........................... 9 Misted light covers ....................... 92 Mountain mode............................. 64 N New vehicle running-in .............. 102 Number plate light ..................... 145 O Odometer ..................................... 57 Oil, engine.......................... 177, 180 Open&Start system ..................... 22 Operation............................
193 Tyre pressure monitoring system............................... 65, 157 Tyre pressures ........................... 185 Tyre repair kit ............................. 162 Tyres .......................................... 156 U Ultrasonic parking assist............. 120 Using this manual .......................... 3 V Vehicle dimensions .................... 184 Vehicle Identification Number .... 179 Vehicle messages ....................... 81 Vehicle personalisation ............... 82 Vehicle ready......
194
