Owner’s Manual Model Year 2014 Edition: November 2013 KTA-2648/8-VX-en 0-1 VAUXHALL Antara Owner’s Manual Model Year 2014 Edition: November 2013 KTA-2648/8-VX-en
Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 18 Seats, restraints ........................... 33 Storage ........................................ 55 Instruments and controls ............. 72 Lighting ...................................... 105 Climate control ........................... 114 Driving and operating ................. 122 Vehicle care ...............................
2 Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". Thank you for choosing a Vauxhall. We wish you many hours of pleasurable driving.
Introduction 5
6 In brief In brief Vehicle unlocking Seat adjustment Seat positioning Initial drive information Press button q to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, operate button above number plate. Radio remote control 3 19, Central locking system 3 20, Load compartment 3 22. Pull handle, slide seat, release handle. Seat position 3 34, Seat adjustment 3 35.
In brief Seat backrests Seat height Power seat adjustment Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly. Do not lean on the seat backrest whilst adjusting it. Seat position 3 34, Seat adjustment 3 35, Seat folding 3 36. Lever pumping motion up = seat higher down = seat lower Operate switches. Seat position 3 34, Seat adjustment 3 35.
8 In brief Positioning = move front switch forwards/backwards Height of = move front part of front part of front switch seat upwards/ downwards Height of = move rear part of rear part of front switch seat upwards/ downwards Height of = move entire front entire seat switch upwards/ downwards Backrest = move upper part of rear switch forwards/backwards Seat position 3 34, Power seat adjustment 3 37. Head restraint adjustment Seat belt Press release button, adjust height and engage. Head restraints 3 33.
In brief Mirror adjustment 9 Exterior mirrors Steering wheel adjustment Select the relevant exterior mirror and adjust it. Convex exterior mirrors 3 27, Electric adjustment 3 27, Folding exterior mirrors 3 27, Heated exterior mirrors 3 28. Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked. Do not adjust steering wheel unless vehicle is stationary and steering wheel lock has been released. Airbag system 3 43, Ignition positions 3 123.
10 In brief Instrument panel overview
In brief 1 2 3 Side air vents ..................... 119 Fixed air vents .................... 120 High beam .......................... 106 Headlight flash ................... 106 Turn and lane-change signals ................................ 108 Exit lighting ......................... 112 Parking lights ..................... 109 4 Cruise control ....................... 90 Remote control on steering wheel ...................... 72 5 6 7 Trip computer ..................... 100 Horn ........................
12 In brief Exterior lighting Turn light switch AUTO = Automatic light control: Headlights are switched on and off automatically. = Off (or deactivation of 7 automatic light control) = Sidelights 8 = Headlights 9 Press button > = Front fog lights r = Rear fog light Lighting 3 105. Headlight flash, high beam and low beam headlight = pull lever flash high = push lever beam low beam = pull lever back towards steering wheel Automatic light control 3 105, High beam 3 106, Headlight flash 3 106.
In brief Hazard warning flashers Horn Washer and wiper systems Windscreen wiper Operated with the ¨ button. Hazard warning flashers 3 107. 13 Press j. & = fast % = slow $ = timed interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Windscreen wiper 3 73, Wiper blade replacement 3 159.
14 In brief Windscreen and headlight washer systems Rear window wiper and washer system Pull lever. Windscreen and headlight washer system 3 73, Washer fluid 3 155. Wiper on = push lever Wiper off = pull lever Wash = press and hold button Rear window wiper and washer system 3 75, Wiper blade replacement 3 159, Washer fluid 3 155. Climate control Heated rear window, heated exterior mirrors Heating is operated by pressing the RÜ button. Heated rear window 3 31, Heated exterior mirrors 3 28.
In brief Demisting and defrosting the windows Air distribution to V (or l). Cooling A/C (or n) and air recirculation 4 are switched on automatically to improve defrosting efficiency (air recirculation 4 is automatically switched off in vehicles with electronic climate control). Set temperature to highest level. Set fan speed to highest level. Switch on heated rear window RÜ. Close centre air vents, open side air vents and direct them towards the door windows. Climate control system 3 114.
16 In brief Automatic transmission Starting off Starting the engine Check before starting off P R N D = = = = park reverse neutral drive Manual mode: move selector lever from D to the left. < = higher gear ] = lower gear The selector lever can only be moved out of P when the ignition is on and the foot brake is applied. To engage P or R, push the release button. Automatic transmission 3 128. ■ Tyre pressure and condition 3 176, 3 207. ■ Engine oil level and fluid levels 3 152.
In brief Stop-start system Parking If the vehicle is at a low speed or at a standstill and certain conditions are fulfilled, activate an Autostop as follows: ■ Depress the clutch pedal ■ shift the selector lever to N ■ release the clutch pedal An Autostop is indicated by the needle at the AUTOSTOP position in the tachometer. To restart the engine, depress the clutch pedal again. Stop-start system 3 124. ■ Always apply the electrical parking brake. Pull switch m. For maximum force, e.g.
18 Keys, doors and windows Keys, doors and windows Keys, locks Key with foldaway key section Keys Replacement keys Keys, locks ................................... 18 Doors ........................................... 22 Vehicle security ............................ 23 Exterior mirrors ............................ 27 Interior mirrors ............................. 28 Windows ...................................... 29 Roof .............................................
Keys, doors and windows Radio remote control Used to operate: ■ Central locking system ■ Anti-theft locking system ■ Anti-theft alarm system The radio remote control has a range of approx. 6 metres. This range can be affected by external influences. The hazard warning flashers confirm operation. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation.
20 Keys, doors and windows Key with fixed key section Open the unit with a small screwdriver in the notch on the cover. Replace the battery (battery type CR2032), paying attention to the installation position. Close the unit. Unlocking Locking Close doors, load compartment, fuel filler flap, bonnet, windows and sunroof. Central locking system Unlocks and locks doors, load compartment and fuel filler flap. A pull on an interior door handle unlocks the respective door.
Keys, doors and windows Note For safety reasons, the vehicle cannot be locked or unlocked via the remote control (and the anti-theft systems will not be activated) if the key is in the ignition switch. If the driver's door is not closed properly, the central locking system will not work. With the engine running, the tailgate will only unlock when the electrical parking brake is applied or automatic transmission is in position P.
22 Keys, doors and windows 9 Warning Use the child locks whenever children are occupying the rear seats. Using a key or suitable screwdriver, turn button on rear door lock to the horizontal position. The door cannot be opened from inside. For deactivation, turn the child lock to the vertical position. Doors Closing Load compartment Tailgate Opening Use the interior handle. Do not operate the button above the number plate while closing the tailgate, as this will unlock it again.
Keys, doors and windows Fault gases, which cannot be seen or smelled, could enter the vehicle. This can cause unconsciousness and even death. Caution To open the tailgate in the event of power interruption: Remove the interior trim cover from the central latch area, then push the lever using a suitable tool. General hints for operating tailgate 9 Warning Do not drive with the tailgate open or ajar, e.g.
24 Keys, doors and windows Activating It monitors: ■ Doors, tailgate, bonnet ■ Passenger compartment including adjoining load compartment ■ Vehicle inclination, e.g. if it is raised ■ Siren power supply ■ Ignition Activation Press button p on the radio remote control twice within 3 seconds. Alternatively, turn key in driver's door towards rear of vehicle again within 3 seconds after locking.
Keys, doors and windows Activation without monitoring of passenger compartment and vehicle inclination 3. Close doors. 4. Activate the anti-theft alarm system. Press button o again to cancel. Control indicator o extinguishes. Status LED 25 Status during the first 30 seconds of anti-theft alarm system activation: LED illu‐ = test, arming delay. minates LED = doors, tailgate or flashes bonnet not completely quickly closed, or system fault.
26 Keys, doors and windows If the alarm has been triggered, the hazard warning lights will not flash upon deactivation. Immobiliser Alarm When triggered, the alarm sounds via a separate battery-backed power sounder, and the hazard warning lights flash simultaneously. The number and duration of alarm signals are stipulated by legislation. The alarm can be silenced by pressing any button of the radio remote control or manually unlocking the driver's door with the ignition key.
Keys, doors and windows Exterior mirrors 27 Folding mirrors Electric folding For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing. With ignition switch in positions ACC or ON, press button n and both exterior mirrors will fold in. Press button n again - both exterior mirrors return to their original position.
28 Keys, doors and windows Heated mirrors Do not use sharp instruments or abrasive cleaners on the exterior mirrors and avoid scratching or damaging the heating elements. Interior mirrors Manual anti-dazzle Automatic dimming Operated by pressing the RÜ button. LED illuminates in the button. Heating works with the key in ignition switch positions ACC or ON and is switched off automatically after a short time. To avoid discharging the battery, operate only with the engine running.
Keys, doors and windows Automatic anti-dazzle Windows Windscreen Heat-reflecting windscreen The heat-reflecting windscreen has a coating which reflects solar radiation. Also data signals, e.g. from toll stations, might be reflected. Windscreen stickers Do not attach stickers such as toll road stickers or similar on the windscreen in the area of the interior mirror. Otherwise the detection zone of the sensor could be restricted.
30 Keys, doors and windows After switching off the ignition, window operation is disabled when the driver's door is opened. Additional switches are located in the front passenger's door and the rear doors. The rear windows do not open fully. Child safety system for rear windows Safety function If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and opened again.
Keys, doors and windows Heated rear window Do not use sharp instruments or abrasive cleaners on the rear window and avoid scratching or damaging the heating elements. Sun visors Operated by pressing the RÜ button. LED illuminates in the button. Heating works with the key in ignition switch positions ACC or ON and is switched off automatically after a short time. To avoid discharging the battery, operate only with the engine running.
32 Keys, doors and windows For incremental operation, briefly press the switch in the required direction. For automatic opening or closing, press and hold the switch. Open Press switch rearwards; it will open automatically unless the switch is pressed again in another direction, or released. Note If the top of the roof is wet, tilt sunroof, allow water to run off and then open sunroof. Close Press and hold switch forwards. Release switch when sunroof reaches desired position.
Seats, restraints Seats, restraints Head restraints ............................ 33 Front seats ................................... 34 Rear seats ................................... 38 Seat belts ..................................... 40 Airbag system .............................. 43 Child restraints ............................. 50 Head restraints 33 Height adjustment Position 9 Warning Only drive with the head restraint set to the proper position. Press release button, adjust height and engage.
34 Seats, restraints Stow head restraints securely in load compartment. Active head restraints In the event of a rear-end impact, the active head restraints automatically tilt forwards. Thus the head is supported so that the risk of whiplash injury is reduced. Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. Note Do not attach objects or components that are not approved for your vehicle to the head restraints.
Seats, restraints Seat adjustment 35 Seat positioning Seat backrests Pull handle, slide seat, release handle. Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly. Do not lean on the seat backrest whilst adjusting it. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. 9 Warning Never store any objects under the seats.
36 Seats, restraints Seat height Lumbar support Seat folding Caution When seat height is in highest position, push head restraints down and lift up sun visors before folding backrest forwards. Lever pumping motion up = seat higher down = seat lower Adjust lumbar support to suit personal requirements using the lever. To increase or decrease lumbar support, move lever forwards or backwards. Push head restraint all the way down. Slide seat as far back as it will go.
Seats, restraints Seat backrests Slide seat forwards. To return the backrest to its original position, slide seat as far back as it will go, lift release lever, move the backrest to upright position, lower lever and the backrest engages. Folding the backrest forwards is possible only when the backrest is in an upright position. Do not operate lever to adjust lumbar support with backrest tilted forward. Power seat adjustment 9 Warning Care must be taken when operating the power seats.
38 Seats, restraints Heating Adjust heating to the desired setting by pressing the ß button for the respective seat one or more times with the ignition switch set to ACC or ON. The control indicator in the button indicates the setting. To deactivate heating, set the heating level to its lowest setting and press the ß button. The control indicator in the button will extinguish. Prolonged use of the highest setting for people with sensitive skin is not recommended.
Seats, restraints 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat folding Push head restraints all the way down, lift backrest release lever and fold backrest forwards and down onto seat cushion. Do not allow passengers to sit on a folded backrest, or place any unrestrained loads on it. To move backrest to its original position, lift and push the backrest into place and ensure the backrest engages.
40 Seats, restraints Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the seated position. Thereby the risk of injury is considerably reduced. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves. Seat belts are designed to be used by only one person at a time. Child restraint system 3 50.
Seats, restraints Height adjustment pretensioners. Do not make any modifications to belt pretensioner components as this will invalidate the vehicle type approval. Three-point seat belt Fastening Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning Withdraw the belt from the retractor, guide it untwisted across the body and insert the latch plate into the buckle.
42 Seats, restraints Removing Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving. To release belt, press red button on belt buckle. Using the seat belt while pregnant 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen.
Seats, restraints Front passenger seat belt reminder Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered, the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning When the engine is running, control indicator k flashes then illuminates if the passenger seat is occupied and the seat belt is not engaged.
44 Seats, restraints EN: NEVER use a rear-facing child restraint system on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD can occur. DE: Nach hinten gerichtete Kindersitze NIEMALS auf einem Sitz verwenden, der durch einen davor befindlichen AKTIVEN AIRBAG geschützt ist, da dies den TOD oder SCHWERE VERLETZUNGEN DES KINDES zur Folge haben kann.
Seats, restraints mesmo, poderá ocorrer a PERDA DE VIDA ou FERIMENTOS GRAVES na CRIANÇA. IT: Non usare mai un sistema di sicurezza per bambini rivolto all'indietro su un sedile protetto da AIRBAG ATTIVO di fronte ad esso: pericolo di MORTE o LESIONI GRAVI per il BAMBINO! EL: ΠΟΤΕ μη χρησιμοποιείτε παιδικό κάθισμα ασφαλείας με φορά προς τα πίσω σε κάθισμα που προστατεύεται από μετωπικό ΕΝΕΡΓΟ ΑΕΡΟΣΑΚΟ, διότι το παιδί μπορεί να υποστεί ΘΑΝΑΣΙΜΟ ή ΣΟΒΑΡΟ ΤΡΑΥΜΑΤΙΣΜΟ.
46 Seats, restraints acest lucru poate duce la DECESUL sau VĂTĂMAREA GRAVĂ a COPILULUI. CS: NIKDY nepoužívejte dětský zádržný systém instalovaný proti směru jízdy na sedadle, které je chráněno před sedadlem AKTIVNÍM AIRBAGEM. Mohlo by dojít k VÁŽNÉMU PORANĚNÍ nebo ÚMRTÍ DÍTĚTE. SK: NIKDY nepoužívajte detskú sedačku otočenú vzad na sedadle chránenom AKTÍVNYM AIRBAGOM, pretože môže dôjsť k SMRTI alebo VÁŽNYM ZRANENIAM DIEŤAŤA.
Seats, restraints 47 Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system The inflated airbags cushion the impact, thereby considerably reducing the risk of injury to the upper body and head of the front seat occupants. 9 Warning Optimum protection is only provided when the seat is in the proper position 3 34. Keep the area in which the airbag inflates clear of obstructions.
48 Seats, restraints Curtain airbag system The curtain airbag system consists of an airbag in the roof frame on each side. This can be identified by the word AIRBAG on the roof pillars. The curtain airbag system is triggered in the event of a side-on impact of a certain severity. The ignition must be switched on. 9 Warning Keep the area in which the airbag inflates clear of obstructions.
Seats, restraints Use the ignition key to choose the position: = front passenger airbag * OFF systems are deactivated and will not inflate in the event of a collision. Control indicator * illuminates continuously on the passenger side of the instrument panel. A child restraint system can be installed in accordance with the chart Child restraint installation locations 3 51. No adult person is allowed to occupy the front passenger seat. V = front passenger airbag ON systems are active.
50 Seats, restraints Child restraints Child restraint systems We recommend the Vauxhall child restraint system which is tailored specifically to the vehicle. When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system. Always comply with local or national regulations. In some countries, the use of child restraint systems is forbidden on certain seats.
Seats, restraints 51 Child restraint installation locations Permissible options for fitting a child restraint system On front passenger seat Weight and age class activated airbag deactivated airbag On rear outboard seats On rear centre seat Group 0: up to 10 kg or approx. 10 months X U1 U, < X Group 0+: up to 13 kg or approx. 2 years X U1 U, < X Group I: 9 to 18 kg or approx. 8 months to 4 years X U1 U, < X Group II: 15 to 25 kg or approx.
52 Seats, restraints Permissible options for fitting an ISOFIX child restraint system On front passenger seat On rear On rear outboard seats centre seat Weight and age class Size class Fixture Group 0: up to 10 kg or approx. 10 months E ISO/R1 X IL X Group 0+: up to 13 kg or approx. 2 years E ISO/R1 X IL X D ISO/R2 X IL X C ISO/R3 X IL X Group I: 9 to 18 kg or approx.
Seats, restraints IL 53 = Suitable for particular ISOFIX restraint systems of the 'vehicle-specific', 'restricted' or 'semi-universal' categories. The ISOFIX restraint system must be approved for the specific vehicle type. IUF = Suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight and age class. X = No ISOFIX child restraint system approved in this weight and age class.
54 Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Permitted installation positions for specific vehicle ISOFIX child restraint systems are marked in the table by IL. No more than two ISOFIX child restraint systems can be installed on the rear seats at the same time, though not on the rear centre seat. ISOFIX mounting brackets are indicated by a label on the backrest.
Storage Storage Storage compartments ................ 55 Load compartment ....................... 67 Roof rack system ......................... 70 Loading information ..................... 70 Storage compartments 9 Warning Do not store heavy or sharp objects in the storage compartments. Otherwise vehicle occupants could be injured by objects being thrown around in the event of hard braking, a sudden change in direction or an accident. Glovebox 55 The glovebox will illuminate when opened.
56 Storage Front storage Coin storage Sunglasses storage Pull handle to open. Push door firmly to close. To open: push the rear part of the cover. To close: pull up cover and push it until it latches into place. Do not use for storing heavy objects. Console net Located in the front passenger foot well. Card holder Located above the coin storage compartment. A card can be retained in the slot for convenient use.
Storage Underseat storage Armrest storage Front passenger seat undertray Console box in front armrest Pull up on front of tray then pull it forwards. Push the tray towards the seat to return it to its original position. To open: pull up lever and lift the lid. To close: lower lid and push it down until it latches into position. Centre console storage To access the storage compartment, power outlet and AUX input, slide the cupholder tray rearwards. Power outlets 3 77.
58 Storage If not in use, the carrier system must be slid back into the vehicle floor. A multifunction box is offered as an accessory for the rear carrier system. There must not be any objects on the bicycles that could become loose during transportation. Completely pull out the rear carrier system until you hear it engage. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again.
Storage Pull up license plate holder and fully insert the holder supports into the retainers. 59 Push the clamping lever and push the bulb holder into the retainer until it hits the stop. Perform this procedure for both tail lamps. Install the tail lamps Open out the bulb holder on the back of the tail lamp completely. First remove the rear (1), then the front (2) tail lamp from the recesses. Check the cable and lamp position to make sure these are correctly installed and are securely located.
60 Storage Lock the rear carrier system Swivel the left clamping lever (1) back first, followed by the right clamping lever (2) until they stop. Both clamping levers must point backwards, otherwise safe functionality is not guaranteed. Note Close the tailgate. Unfold pedal crank recesses Fold one or both pedal crank recesses upwards until the diagonal support engages. Remove the pedal crank mounts from the pedal crank recesses.
Storage Adapting the rear carrier system to a bicycle With the rotary lever on the pedal crank recess, roughly adapt the adjustable pedal crank unit to the protrusion of the pedal crank. If the bicycle has straight pedal cranks, unscrew the pedal crank unit completely (position 5). 61 Press the release lever and withdraw the wheel recesses. If the bicycle has curved pedal cranks, screw in the pedal crank unit all the way (position 1).
62 Storage Prepare the bicycle for attachment Note The maximum width for the pedal crank is 38.3 mm and the maximum depth is 14.4 mm. Rotate the left pedal (without a chain cog) vertically downwards. The pedal on the left pedal crank must be horizontal. The front bicycle must have its front wheel facing left. The rear bicycle must have its front wheel facing right. Attaching a bicycle to the rear carrier system Put on the bicycle.
Storage Attach the pedal crank by rotating the attachment screw on the pedal crank mount. Caution Make sure to pull out the wheel recesses as far as necessary to have both bicycle tyres placed in the recesses. Otherwise a horizontal mounting of the bicycle is not ensured. Disregard could lead to damage of the bicycle wheels caused by hot exhaust fumes. 63 Place the bicycle upright using the rotary lever on the pedal crank recess.
64 Storage Removing a bicycle from the rear carrier system Secure both bicycle wheels to the wheel recesses using strap retainers. Check the bicycle to make sure it is secure. Caution Ensure gap between bicycle and vehicle is at least 5 cm. If necessary, loosen handlebar and swivel sideways. The settings for the wheel recesses and on the rotary lever on the pedal crank recess should be noted and saved for each bicycle. Correct presetting will facilitate refitting of the bicycle.
Storage Retracting the rear carrier system 65 Press release lever and slide in wheel recesses all the way as far as they will go. Insert the strap retainer and pull tightly downwards as far as possible. Push the pedal crank mounts into the pedal crank recess as shown in the illustration. Disengage the locking lever on the diagonal support and fold both pedal crank recesses down. 9 Warning Risk of pinching.
66 Storage Push the clamping lever down and pull both lamp supports out of the recesses. Swivel first the right clamping lever (1) forwards, followed by the left clamping lever (2), until they can be engaged in their respective recesses. Pull up license plate holder and fold down into horizontal position. Fold in the bulb holders on the backs of the tail lamps. First place the front tail lamp (1), then the rear tail lamp (2) in the recesses and push down as far as possible.
Storage Raise the release lever and hold. Lift the system slightly and push it into the bumper until it engages. Release lever must return to original position. Load compartment 67 Closing the cover Storage compartments in the load compartment 9 Warning If the system cannot be correctly engaged, please seek the assistance of a workshop. Located on both sides of the load compartment floor. Load compartment cover Do not place any objects on the cover.
68 Storage Removing the cover Open load compartment cover. Pull socket on either side of cover towards centre of vehicle, lift and remove cover from the side guides. Fit in reverse order. Rear floor storage cover To access the rear floor storage compartment, pull floor cover handle upwards. Depending on version, to access the rear floor storage compartment, push both levers on the floor cover towards the handle and pull up the cover by the handle.
Storage Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor. Jack and vehicle tools 3 173. Tyre repair kit 3 179. Temporary spare wheel 3 185. Where present, hang the hook to the upper part of the tailgate opening. Caution Only use the hook for hanging up the rear floor cover and the height adjustable cover. Lashing eyes 69 The lashing eyes are designed to secure items against slippage, e.g.
70 Storage Roof rack system Loading information Roof rack ■ Heavy objects in the load compartment should be evenly distributed and placed as far forward as possible. Ensure the backrests are securely engaged. If objects can be stacked, the heavier objects should be placed at the bottom. With rear seats in the folded position, objects must not be stacked higher than the seat backrests. ■ Secure objects with lashing straps attached to lashing eyes 3 69. ■ Secure loose objects in the load compartment, e.
Storage To calculate the EC kerb weight, enter the data for your vehicle in the Weights table at the front of this manual. The EC kerb weight includes weights for the driver (68 kg), luggage (7 kg) and all fluids (tank 90 % full). Optional equipment and accessories increase the kerb weight. ■ Driving with a roof load increases the sensitivity of the vehicle to cross-winds and has a detrimental effect on vehicle handling due to the vehicle's higher centre of gravity.
72 Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Controls ....................................... 72 Warning lights, gauges and indi‐ cators ........................................... 79 Information displays ..................... 91 Vehicle messages ........................ 98 Trip computer ............................. 100 Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked.
Instruments and controls Horn Windscreen wiper/washer 73 Adjustable wiper interval Windscreen wiper Press j. & = fast % = slow $ = timed interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Do not use if the windscreen is frozen. Switch off in car washes. To set the wiping interval to a value between 1 and 10 seconds: ■ Switch on ignition. ■ Push lever down from position §.
74 Instruments and controls In this mode, wiping frequency is also affected by vehicle speed. As vehicle speed increases, wiping will become more frequent. Automatic wiping with rain sensor $ = automatic wiping with rain sensor The rain sensor detects the amount of water on the windscreen and automatically regulates the frequency of the windscreen wiper. The wiper operates for one cycle to check the system when the key is turned to ignition switch position ACC.
Instruments and controls Control indicator G illuminates in the instrument cluster when the washer fluid level is low. Wiper activated lighting With light switch in the AUTO position, when the windscreen wiper is operated for 8 cycles or more the exterior lights illuminate automatically. Rear window wiper/washer Move lever to activate the rear window wiper: Push lever = wiper on Pull lever = wiper off To activate rear window washer system, press and hold button on end of lever.
76 Instruments and controls Automatic time synchronisation 9 Warning Board-Info-Display The road surface may already be icy even though the display indicates a few degrees above 0 °C. Clock Graphic-Info-Display, Colour-Info-Display 3 93. Date and time are shown in the Info-Display. Board-Info-Display 3 91. The RDS (Radio Data System) signal of most VHF transmitters automatically sets the time, identified by } in the display. Some RDS transmitters do not send a correct time signal.
Instruments and controls Deactivate (Clock Sync.Off) or activate (Clock Sync.On) automatic time synchronisation with the arrow buttons on the Infotainment system. To set date and time manually, select the menu item for time and date setting from the Settings menu and make the desired setting. The value ready for modification is marked with arrows. Use the arrow buttons to make the required setting. The setting is saved when the menu item is exited.
78 Instruments and controls Electrical accessories that are connected must comply with the electromagnetic compatibility requirements laid down in DIN VDE 40 839. Do not connect any current-delivering accessories, e.g. electrical charging devices or batteries. Do not damage the outlet by using unsuitable plugs. Stop-start system 3 124. 12 Volt power outlets are located beneath the cupholder in the front centre console, in the rear centre console and on the right-hand side of the load compartment.
Instruments and controls Warning lights, gauges and indicators Instrument cluster Odometer The odometer display is located in the centre of the instrument cluster. 79 To reset, press and hold the trip odometer button for a few seconds with the ignition on. Tachometer In some versions, the needles of the instruments briefly rotate to the end position when the ignition is switched on. Speedometer The bottom line displays the recorded distance in miles. Trip odometer Indicates vehicle speed.
80 Instruments and controls Fuel gauge Service display The engine oil life system lets you know when to change the engine oil and filter. Based on driving conditions, the interval at which an engine oil and filter change will be indicated can vary considerably. Change engine oil 3 88. Transmission display Displays the fuel level in the tank. Control indicator Y illuminates if the level in the tank is low. Refuel immediately 3 144. Never run the tank dry.
Instruments and controls Control indicators on the instrument panel 9 Danger Risk of fatal injury for a child using a child restraint system together with activated front passenger airbag. Risk of fatal injury for an adult person with deactivated front passenger airbag. k illuminates red. Front passenger seat belt reminder 3 41. * illuminates yellow. The front passenger airbag is deactivated 3 48.
82 Instruments and controls Control indicators in the instrument cluster
Instruments and controls Turn signal O illuminates or flashes green. The relevant control indicator flashes when the turn signal is switched on 3 108. Rapid flashing: failure of a turn signal bulb or the associated fuse or failure of a turn signal light on trailer. Both control indicators flash when the hazard warning flashers are active 3 107. Bulb replacement 3 159, Fuses 3 165. Turn signals 3 108. Seat belt reminder Seat belt reminder for front seats X for driver's seat illuminates or flashes red.
84 Instruments and controls Interrupt your journey immediately. Remove key and check drive belt condition and tensioning before seeking the assistance of a workshop. Malfunction indicator light Z illuminates or flashes yellow. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. If it does not illuminate, seek the assistance of a workshop. Can illuminate briefly when driving; this is normal and does not indicate a system fault.
Instruments and controls Illuminates when engine is running if fluid level for brake hydraulics is too low 3 155. Brake system 3 135. Electrical parking brake m illuminates or flashes red. When the engine is started, m illuminates briefly. If it does not illuminate, seek the assistance of a workshop. Illuminates Electrical parking brake is applied 3 136. Flashes Electrical parking brake is not fully applied or released.
86 Instruments and controls Flashes briefly when the engine is running The system is temporarily disabled. Flashes continuously when the engine is running System fault. Seek the assistance of a workshop immediately. All wheel drive 3 133. Descent control system u illuminates yellow and/or green. Both the yellow and green control indicators illuminate briefly when the ignition is switched on. Green Illuminates when system is ready for operation.
Instruments and controls Flashes The system is actively engaged. Engine output may be reduced and the vehicle may be braked automatically to a small degree. Electronic Stability Control 3 137. Electronic Stability Control off t illuminates yellow. When the ignition is switched on, t illuminates briefly. If it does not illuminate, seek the assistance of a workshop. Illuminates when ESC has been switched off manually by pressing button t on the centre console. Electronic Stability Control 3 137.
88 Instruments and controls Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. If it does not illuminate, seek the assistance of a workshop. Illuminates when the engine is running Caution Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels. 1. Depress clutch. 2. Select neutral gear, set selector lever to N. 3. Move out of the flow of traffic as quickly as possible without impeding other vehicles. 4.
Instruments and controls Low fuel Immobiliser Y illuminates yellow. When the engine is started, Y illuminates briefly. If it does not illuminate, seek the assistance of a workshop. Illuminates during driving when fuel level in tank is too low. Refuel immediately 3 144. Never run the tank dry. Erratic fuel supply can cause catalytic converter to overheat 3 128. Diesel engines: if the tank has been run dry, bleed the fuel system 3 159. Fuel tank capacity 3 206. Catalytic converter 3 128.
90 Instruments and controls Illuminates when the front fog lights are switched on 3 108. Rear fog light r illuminates yellow. Illuminates when the rear fog light is switched on 3 109. Cruise control m illuminates yellow or green. Illuminates yellow The system is ready for operation. Illuminates green A certain speed is stored. Cruise control 3 140. Speed warning à illuminates yellow.
Instruments and controls Information displays Board-Info-Display The Info-Display is located in the instrument panel above the Infotainment system. The Info-Display is located in the instrument panel above the Infotainment system. An F in the display indicates a fault. Have the cause of the fault remedied by a workshop. Trip computer, Board-Info-Display 3 100.
92 Instruments and controls Select using the left adjuster wheel on the steering wheel System settings ■ ■ ■ ■ ■ ■ ■ Time, setting minutes Date, setting day Date, setting month Date, setting year Ignition logic Language selection Setting units of measure Automatic time synchronisation Turn the adjuster wheel to call up the required function. Press the adjuster wheel to open the BC menu, to select marked items and confirm commands.
Instruments and controls Some transmitters do not send a correct time signal. In such cases, switch off automatic time synchronisation and set the time manually. Deactivate (Clock Sync.Off) or activate (Clock Sync.On) automatic time synchronisation with the arrow buttons. The value ready for modification is marked with arrows. Use the arrow buttons to make the required setting. The setting is saved when the menu item is exited.
94 Instruments and controls The type of information and how it is displayed depends on the equipment of the vehicle and the settings of the trip computer and Infotainment system. Some information appears on the display in an abbreviated form. An F in the display indicates a fault. Have the cause of the fault remedied by a workshop. Trip computer, Graphic-Info-Display, Colour-Info-Display 3 101.
Instruments and controls Turn ■ To mark a menu option ■ To set a numeric value or to display a menu option Press ■ To select or activate the marked option ■ To confirm a set value ■ To switch a system function on/off To exit a menu, turn the multifunction knob left or right to Return or Main and select. Select using the left adjuster wheel on the steering wheel Turn the adjuster wheel to call up the required function. Press the adjuster wheel to select marked items and confirm commands.
96 Instruments and controls System settings ■ Contrast ■ Day / Night ■ Ignition logic Setting date and time The settings are accessed via the Settings menu. Press the Main button (not found on all Infotainment systems) on the Infotainment system, to call up main display. Press the Settings button. On Infotainment System CD 30, ensure no menu has been selected. The Settings menu is displayed.
Instruments and controls Language selection The display language for some functions can be selected. Select menu item Language from the Settings menu. The available languages are displayed. 97 Setting units of measure Select the desired language. Selections are indicated by a 6 in front of the menu item.
98 Instruments and controls Adjusting contrast (Graphic-Info-Display) Always day design; black or coloured text on a light background. Always night design; white or coloured text on a dark background. Selections are indicated by a o in front of the menu item. Ignition logic See Infotainment system instruction manual. Select menu item Contrast from the Settings menu. The menu is displayed. Confirm the required setting.
Instruments and controls ■ During automatic self-cleaning of the diesel particle filter 3 127. ■ In vehicles equipped with engine overspeed warning; when vehicle speed exceeds 75 mph 3 90. When the vehicle is parked and/ or the driver's door is opened ■ When the key is in the ignition switch. ■ With exterior lights on. In vehicles with tyre pressure monitoring system, if low tyre pressures are detected, relevant information appears on the information display.
100 Instruments and controls Trip computer Trip computer in BoardInfo-Display The trip computer provides information on driving data, which is continually recorded and evaluated electronically. Access trip computer vehicle data by pressing the BC button on the Infotainment system or the left adjuster wheel on the steering wheel. Some of the functions appear on the display in an abbreviated form. Once a function has been selected, the subsequent rows of the trip computer function are displayed.
Instruments and controls After refuelling, the range is updated automatically after a brief delay. If the fuel in the tank allows less than 30 miles of travel, the warning Range appears on the display. If the fuel in the tank allows less than 20 miles of travel, the warning Refuel! appears on the display. Acknowledge the menu item 3 91.
102 Instruments and controls page provides information on range, average consumption and instantaneous consumption. To display other trip computer data, press the BC button on the Infotainment system and select the trip computer menu in the display. The information of the two trip computers can be reset separately, making it possible to display different trip distances. Graphic-Info-Display, Colour-Info-Display 3 93. Range is calculated from current fuel tank content and instantaneous consumption.
Instruments and controls 103 Stop watch Average consumption Display of average consumption. The measurement can be reset at any time. Resetting trip computer information To reset all information of a trip computer, select menu item All values. After resetting, "- - -" is displayed for the trip computer information selected. The recalculated values are displayed after a brief delay. Select BC 1 or BC 2 from the trip computer menu.
104 Instruments and controls Travel Time: Measurement of the time from manual activation via Start to manual deactivation via Reset. Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost.
Lighting Lighting Exterior lighting Light switch Exterior lighting .......................... 105 Interior lighting ........................... 110 Lighting features ........................ 112 105 Tail lights Tail lights illuminate together with low beam/high beam and sidelights. Automatic light control Turn light switch: AUTO = Automatic light control: Headlights are switched on and off automatically depending on external lighting conditions. = Off (or deactivation of 7 automatic light control).
106 Lighting To ensure automatic light control functions properly, do not cover the light sensor on top of the instrument panel. Driving abroad 3 107. Wiper activated lighting With light switch in the AUTO position, when the windscreen wiper is operated for 8 cycles or more the exterior lights illuminate automatically. To switch from low to high beam, push lever. To switch to low beam, pull lever back again. Control indicator C 3 89.
Lighting Vehicles without automatic level control system Turn thumb wheel ? to required position: 0 = front seats occupied 1 = all seats occupied 2 = all seats occupied and load compartment laden 3 = driver's seat occupied and load compartment laden Vehicles with automatic level control system Turn thumb wheel to required position: 0 = front seats occupied 1 = all seats occupied 1 = all seats occupied and load compartment laden 2 = driver's seat occupied and load compartment laden Automatic level control 3
108 Lighting Turn and lane-change signals For three flashes, e.g. when changing lanes, press the lever until resistance is felt and then release. Move the lever to the resistance point and hold for longer indication. The volume of the turn signal audible warning is dependent upon vehicle speed. Switch the turn signal off manually by moving the lever to its original position. Control indicators O 3 83.
Lighting Rear fog lights The vehicle rear fog light is deactivated when towing. Parking lights 109 Confirmed by a signal tone and the corresponding turn signal control indicator. To deactivate, switch on the ignition or move the turn signal lever in the opposite direction. Reversing lights The reversing lights come on when the ignition is on and reverse gear is selected. Centre high-mounted brake light Operated with the r button.
110 Lighting Interior lighting Instrument panel illumination control If driver's door is opened or q is pressed on the remote control, instrument panel illuminates automatically for 30 seconds until ignition switch is turned to position ACC. Display mode 3 93. Front courtesy light Interior lights During entry and exit of the vehicle, the front and rear courtesy lights automatically switch on and then off after a delay.
Lighting Load compartment lighting 111 Reading lights Front reading lights Courtesy lights can be turned off immediately by pressing button K. Ignition switch illumination Illuminates when you open a door. Switch off immediately by pressing button K in the roof lining. Glovebox illumination Illuminates when the glovebox is opened. Illuminates when a door or the tailgate is opened. Operated with the L and M buttons.
112 Lighting Rear reading lights Lighting features Switching on Entry lighting Welcome lighting Depending upon outside light conditions, when unlocking the vehicle with the remote control the hazard warning lights flash twice and the exterior and interior lights illuminate for 20 seconds. This function facilitates locating the vehicle when it is dark. Left and right rear reading lights are individually operable. Press to activate and deactivate.
Lighting Battery discharge protection To prevent the battery from becoming discharged, the exterior lights turn off automatically 10 minutes after the ignition is switched off. Battery discharge protection will not work if the lights are turned on 10 minutes after the ignition has been switched off; the key cannot be removed from the ignition switch until the battery is recharged.
114 Climate control Climate control Climate control systems ............. 114 Air vents ..................................... 119 Maintenance .............................. 120 Climate control systems Heating and ventilation system Temperature red = warm blue = cold Heating will not be fully effective until the engine has reached normal operating temperature. Air distribution Controls for: ■ Temperature ■ Air distribution ■ Fan speed ■ Demisting and defrosting Heated rear window Ü 3 31.
Climate control Demisting and defrosting ■ Set the air distribution switch to l or J ■ Set temperature control to warmest level ■ Set fan to highest level ■ Close centre air vents ■ Open side air vents and direct them towards the door windows Heated rear window Ü 3 31. Air conditioning system In addition to the heating and ventilation system, the air conditioning system has controls for: n = cooling 4 = air recirculation Ü = demisting and defrosting Heated seats ß 3 38.
116 Climate control directed to it. If windscreen mists up from outside, activate windscreen wiper and deactivate l. Demisting and defrosting Maximum cooling Briefly open the windows and sunroof so that hot air can disperse quickly. ■ Press button n to activate air conditioning. ■ Press button 4 to activate air recirculation. ■ Set air distribution switch to M. ■ Set temperature control to coldest level. ■ Set fan to highest level. ■ Open all vents.
Climate control Temperature preselection ■ Fan speed ■ Temperature on front passenger side AUTO = Automatic mode t = Automatic air recirculation = Demisting and defrosting V Cooling A/C, Air recirculation 4 3 115. Note Do not cover the interior temperature sensor (located beside the fan switch) or the sunlight sensor (located in front of the windscreen defroster vents) as this could cause the system to malfunction. Heated rear window RÜ 3 31, Heated seats ß 3 38.
118 Climate control Climate control system settings can be changed by pressing button A/C or by adjusting the fan speed or air distribution switch. Changing a setting will deactivate Automatic mode. To return to Automatic mode: Press AUTO button. Cooling A/C 3 115. Fan speed x To deactivate Automatic mode, change fan speed manually or turn fan to position off x. To return to Automatic mode: Switch on fan and press AUTO button.
Climate control To switch off window demisting and defrosting, press button V again, press AUTO button, adjust fan speed or air distribution switch. Air vents Adjustable air vents 119 Control the air temperature at the side air vents by adjusting the temperature control switch. At least one air vent must be open while the cooling A/C is on. Direct the flow of air by tilting and swivelling the slats. To open and close the vents, turn the horizontal adjuster wheel to the left or right.
120 Climate control Fixed air vents Additional air vents are located beneath the windscreen, door windows and in the front and rear foot wells. The area underneath the front seats must be kept clear, to allow air flow to the rear passenger foot well. Maintenance Air intake Active carbon filter In addition to the particle filter the active carbon filter reduces odours.
Climate control ■ Cleaning of condenser and evaporator drainage ■ Performance check 121
122 Driving and operating Driving and operating Driving hints ............................... 122 Starting and operating ............... 122 Engine exhaust .......................... 127 Automatic transmission .............. 128 Manual transmission .................. 132 Drive systems ............................ 133 Brakes ........................................ 135 Ride control systems ................. 137 Driver assistance systems ......... 140 Fuel ............................................
Driving and operating Ignition switch positions Starting the engine LOCK ACC Manual transmission: operate clutch and brake pedals. Automatic transmission: operate brake pedal and move selector lever to P or N. Do not operate accelerator pedal. Diesel engines: turn the key to position ON for preheating until control indicator ! extinguishes 3 87. Turn key briefly to position START and release. Key returns automatically to position ON.
124 Driving and operating 30 seconds. If engine does not start, wait 10 seconds before repeating starting procedure. Ensure the engine oil is of the correct viscosity, the correct fuel is used, vehicle services are performed regularly and the battery is sufficiently charged. Overrun cut-off The fuel supply is automatically cutoff during overrun, i.e. when the vehicle is driven with a gear engaged but accelerator is released.
Driving and operating An Autostop is indicated by the needle at the AUTOSTOP position in the tachometer. During an Autostop, the heating, power steering and brake performance will be maintained. Air conditioning system may or may not inhibit the stop-start system according to the cooling performance. Caution The steering assist can be reduced during an Autostop. Conditions for an Autostop The stop-start system checks if each of the following conditions is fulfilled.
126 Driving and operating If the selector lever is shifted out of neutral before depressing the clutch first, control indicator - illuminates. Control indicator - 3 89. Restart of the engine by the stop-start system The selector lever must be in neutral to enable an automatic restart. If one of the following conditions occurs during an Autostop, the engine will be restarted automatically by the stop-start system.
Driving and operating Engine exhaust 9 Danger Engine exhaust gases contain poisonous carbon monoxide, which is colourless and odourless and could be fatal if inhaled. If exhaust gases enter the interior of the vehicle, open the windows. Have the cause of the fault rectified by a workshop. Avoid driving with an open load compartment, otherwise exhaust gases could enter the vehicle. The filter is cleaned by periodically burning off the soot particles at high temperature.
128 Driving and operating may be a fault in the diesel particle filter 3 84. Cleaning is not possible, seek the assistance of a workshop immediately. Caution If the cleaning process is interrupted, there is a risk of provoking severe engine damage. Cleaning takes place quickest at high engine speeds and loads. Do not switch off the engine until the cleaning process is complete. This is indicated by the extinguished control indicator %.
Driving and operating D = drive position (automatic mode) 1-6 = selected gear in manual mode Selector lever P = park position, wheels are locked, engage only when the vehicle is stationary and the electrical parking brake is applied R = reverse gear, engage only when vehicle is stationary N = neutral or idle D = drive position (automatic mode with all gears) The selector lever is locked in position P and N and can only be moved when the ignition is on and the foot brake is applied.
130 Driving and operating Manual mode Move selector lever out of position D towards the left and then forwards or backwards. < = Shift to a higher gear. ] = Shift to a lower gear. Tip selector lever in the appropriate direction. It then returns to the centre position. Gearshifting in manual mode can be achieved whilst accelerating. If the engine speed is too low, the transmission will automatically shift to a lower gear, even in manual mode, to prevent the engine from stalling.
Driving and operating Activation In automatic mode, press button s; control indicator s illuminates in the instrument cluster 3 88. The settings of certain electronic systems are adapted to reduce fuel consumption: ■ The engine reacts less quickly to the accelerator pedal. ■ Automatic upshift points occur sooner and downshift points occur later. ■ The transmission locks itself to the engine at cruising speeds, to improve efficiency and increase power and torque.
132 Driving and operating 3. Remove trim cover. Manual transmission Caution It is not advisable to drive with the hand resting on the selector lever. 4. Press and hold shift lock release button. 5. Shift to neutral (N). 6. Replace trim cover. 7. Start engine and shift to chosen gear. Have the cause of the power supply interruption remedied by a workshop. To engage reverse, with the vehicle stationary, wait 3 seconds after depressing clutch pedal and engage the gear.
Driving and operating Drive systems All-wheel drive All-wheel drive is an active-ondemand system that engages automatically, with no action required by the driver. Depending on the driving environment, the vehicle switches between two-wheel drive and four-wheel drive, to give the vehicle more traction and stability when necessary. If the front wheels begin to slip, the rear wheels will automatically begin to drive the vehicle as required.
134 Driving and operating Towing the vehicle 3 188. Driving through water Do not exceed the maximum wading depth 3 204. Check the depth of water: choose the lowest entry and departure angles before entering. Maintain a steady engine speed, to help prevent water from entering the exhaust system, but do not exceed 3 mph, to avoid splashing the water. Drive with the flow wherever possible, not against it.
Driving and operating ■ Transfer box and underguard ■ Engine oil pan and underguard Observe the following: ■ Do not spray high-pressure water directly at the vehicle seals ■ The wheels must be removed to clean all mud and stones from the brake calipers and to check brake pad wear ■ The areas on the upper side of the underguards must be cleared of stones, to prevent damage to the engine oil pan and the fuel tank Brakes The brake system comprises two independent brake circuits.
136 Driving and operating hard braking, the vehicle can no longer be steered and may swerve. You can continue driving, provided you drive with care and anticipation. Have the cause of the fault remedied by a workshop. Parking brake Electrical parking brake Applying when vehicle is stationary Pull switch m, the electrical parking brake operates automatically with adequate force. For maximum force, e.g. parking with a trailer or on inclines, pull switch m twice.
Driving and operating Fault Failure mode of electrical parking brake is indicated by control indicator j 3 85. In the event of a fault, to apply electrical parking brake: pull and hold the switch m for a few seconds. If control indicator m illuminates, electrical parking brake has been applied successfully. To release electrical parking brake: push and hold the switch m for a few seconds. If control indicator m extinguishes, electrical parking brake has been released successfully.
138 Driving and operating 9 Warning Do not let this special safety feature tempt you into taking risks when driving. Adapt speed to the road conditions. Deactivation Switch off ESC function, to allow engine rpm to increase, by pressing button t briefly. Control indicator t illuminates in the instrument cluster. ESC is reactivated by pressing button t again. The control indicator extinguishes. Control indicator t 3 87.
Driving and operating Activation At speeds below approx. 30 mph, press button u. The green control indicator u flashes in the instrument cluster, to show DCS is in operation. DCS will not activate at speeds above 30 mph, even if the button is pressed. Deactivation Press button u again. The green control indicator u extinguishes. Depressing the foot brake or accelerator will also cause the system to be deactivated.
140 Driving and operating Driver assistance systems stored and maintained. Control indicator m illuminates green. Accelerator pedal can be released. Vehicle speed can be increased by depressing the accelerator pedal. When the accelerator pedal is released, the previously stored speed is resumed. 9 Warning Driver assistance systems are developed to support the driver and not to replace the driver's attention. The driver accepts full responsibility when driving the vehicle.
Driving and operating 141 Deactivation Parking assist Activation Resume stored speed The parking assist system makes parking easier by measuring the distance between the vehicle and obstacles to the front and rear, and giving acoustic signals. It is the driver, however, who bears full responsibility for the parking manoeuvre. The system consists of four ultrasonic parking sensors in both the front and rear bumpers. Control indicator r 3 86. With the ignition on, the system must be activated manually.
142 Driving and operating 30 cm, the signal is continuous. The acoustic signal may differ depending on the type of object detected. Deactivation To deactivate, press the button again and the LED in the button will extinguish. The control indicator r in the instrument cluster will illuminate until the vehicle speed exceeds 18 mph. The system is deactivated automatically when the vehicle speed is above 5 mph or when selector lever is in neutral (automatic transmission in N or P).
Driving and operating Fuel Caution Fuel for petrol engines Only use unleaded fuel that complies with European standard EN 228 or E DIN 51626-1 or equivalent. Your engine is capable of running with E10 fuel that fulfills these standards. E10 fuel contains up to 10 % bioethanol. Use fuel with the recommended octane rating 3 202. Use of fuel with too low an octane rating can reduce engine power and torque and slightly increases fuel consumption.
144 Driving and operating Caution Certain additives in petrol could, in combination with ethanol, cause reduced driveability. For this reason, refuel with a full tank of petrol every 6000 miles. Use up the majority of this before refuelling the car again. Fuel for diesel engines Only use diesel fuel that complies with EN 590. In countries outside the European Union use Euro-Diesel fuel with a sulphur concentration below 50 ppm.
Driving and operating The fuel filler cap can be retained in the holder on the inside of the fuel filler flap. When refuelling, fully insert the pump nozzle and switch it on. After the automatic cut-off, the fuel tank can be topped up with a maximum two doses of fuel. Caution Wipe off any overflowing fuel immediately. After refuelling, replace the fuel filler cap and turn it clockwise until you hear several clicks.
146 Driving and operating Trailer hitch General information The coupling ball bar is kept in a bag, fastened with a strap and is stowed below the floor cover in the load compartment. Only use towing equipment that has been approved for your vehicle. Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment.
Driving and operating The permitted trailer load applies up to the specified incline and up to an altitude of 1000 metres above sea level. Since engine power decreases as altitude increases due to the air becoming thinner, therefore reducing climbing ability, the permissible gross train weight also decreases by 10 % for every 1000 metres of additional altitude. The gross train weight does not have to be reduced when driving on roads with slight inclines (less than 8 %, e.g. motorways).
148 Driving and operating Remove sealing plug from the hole for the coupling ball bar and stow it in the load compartment. Confirm that the colour marking on the lever is red. Inserting the coupling ball bar Insert the coupling ball bar into the coupling housing and push firmly downwards until the coupling ball bar audibly engages. If it does not engage, repeat fitting procedure. Do not swing the coupling ball bar to the left or right, or upwards and downwards, to avoid disrupting correct fitting.
Driving and operating 9 Warning Towing a trailer is permitted only when the coupling ball bar is fitted correctly. If the coupling ball bar cannot be properly attached, seek the assistance of a workshop. Eye for break-away stopping cable In the case of trailers with brakes, attach the break-away stopping cable to the eye - not to the coupling ball bar. Dismounting the coupling ball bar Unlock coupling ball bar and remove key. Push lever to the left, towards the coupling ball bar and turn it downwards.
150 Vehicle care Vehicle care General Information ................... 150 Vehicle checks ........................... 151 Bulb replacement ....................... 159 Electrical system ........................ 165 Vehicle tools .............................. 173 Wheels and tyres ....................... 175 Jump starting ............................. 187 Towing ....................................... 188 Appearance care .......................
Vehicle care ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.g. anti-theft alarm system. Putting back into operation When the vehicle is to be put back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir. ■ Check the engine oil level.
152 Vehicle care Bonnet Caution Opening Do not press the bonnet into the latch to avoid dents. Engine oil Pull the release lever and return it to its original position. Locate the safety catch, found slightly left of centre on the underside of the bonnet, push the catch upwards and lift the bonnet gently. The bonnet is held open automatically. If the bonnet is opened during an Autostop, the engine will be restarted automatically for safety reasons. Air intake 3 120.
Vehicle care Insert dipstick to the stop on the handle and make half a turn. 153 Control indicators for engine oil pressure I 3 87, low engine oil S 3 88 and engine oil life C 3 88. Once the engine oil has been changed, the engine oil life monitor needs to be reset. Seek the assistance of a workshop. Engine coolant Different dipsticks are used depending on engine variant. When the engine oil level has dropped to the MIN mark, top up engine oil.
154 Vehicle care the coolant concentration checked and have the cause of the coolant loss remedied by a workshop. Engine coolant temperature control indicator W 3 87. Power steering fluid Caution If the cooling system is cold, the coolant level should be between the MIN and MAX marks. Top up if the level is low. 9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly.
Vehicle care Washer fluid Do not spray washer fluid onto windscreen in freezing weather, to avoid ice forming and impairing vision. In cold weather, do not fill the washer fluid reservoir more than three quarters full, to allow enough room for expansion if the fluid freezes, and to prevent damage to the reservoir. 155 Brake fluid 9 Warning Brake fluid is poisonous and corrosive. Avoid contact with eyes, skin, fabrics and painted surfaces.
156 Vehicle care battery. Short-distance-driving and frequent engine starts can discharge the vehicle battery. Avoid the use of unnecessary electrical consumers. Caution Only use high-performance brake fluid approved for the vehicle. Brake fluid 3 195. Brake fluid level control indicator R 3 84. Clutch fluid 9 Warning Clutch fluid is poisonous and corrosive. Avoid contact with eyes, skin, fabrics and painted surfaces.
Vehicle care Retrofitted electrical or electronic accessories can place an additional load on the vehicle battery or discharge the battery. Seek the assistance of a workshop regarding technical possibilities, such as fitting a more powerful battery. Ensure the ignition is switched off before reconnecting the vehicle battery. Then perform the following actions: 1. Set date and time in the information display 3 76. 2. If necessary, activate the power windows and sun roof 3 29, 3 31.
158 Vehicle care Charging the vehicle battery 9 Warning On vehicles with stop-start system, ensure that the charging potential does not exceed 14.6 volts when using a battery charger. Otherwise the vehicle battery might be damaged. Jump starting 3 187. Warning label Meaning of symbols: ■ No sparks, naked flames or smoking. ■ Always shield eyes. Explosive gases can cause blindness or injury. ■ Keep the vehicle battery out of reach of children.
Vehicle care operation 3 times or more while the engine is switched off, to avoid air entering the fuel line. Check diesel fuel filter at shorter intervals if the vehicle is subjected to extreme operating conditions. If there is water in the diesel fuel filter, control indicator U illuminates in the instrument cluster 3 89. Drain the water immediately. Wiper blade replacement Bulb replacement Wiper blades on the windscreen Switch off the ignition and turn off the relevant switch or close the doors.
160 Vehicle care 1. Switch off the ignition and headlight switch. 2. Open the bonnet, release the 11 retainers and remove the radiator cover. 3. Remove 3 bolts and withdraw headlamp. 4. Depress harness connector tags and disconnect headlamp wiring. 5. Remove the headlamp assembly. Headlamp assembly installation is the reverse of removal - ensure locating dowel aligns with its socket. Do not overtighten bolts or retainers.
Vehicle care 5. Engage bulb retaining spring and replace headlamp cap. 6. Reinstall headlamp assembly. Front turn signal 5. Reinstall bulb holder in lamp assembly by rotating it clockwise. 6. Reinstall headlamp assembly. Sidelights 161 5. Reinstall bulb holder in lamp assembly and replace headlamp cap. 6. Reinstall headlamp assembly. Xenon headlights 1. Remove headlamp assembly 3 159. 2. Rotate bulb holder anticlockwise and withdraw bulb holder from lamp assembly. 3.
162 Vehicle care Low and high beam 9 Danger Xenon headlights work under extremely high electrical voltage. Do not touch. Have bulbs replaced by a workshop. Front turn signal 1. Remove headlamp assembly 3 159. 2. Rotate bulb holder anticlockwise and withdraw bulb holder from lamp assembly. 3. Press and rotate bulb anticlockwise to remove it from bulb holder. 4. Insert new bulb into bulb holder by pressing and rotating it clockwise. 5. Reinstall bulb holder in lamp assembly by rotating it clockwise. 6.
Vehicle care 1. Remove 2 screws from panel on underside of vehicle below front fog lights and remove panel. 2. Disconnect harness connector from bulb holder and rotate bulb holder anticlockwise. 3. Remove bulb holder from lamp assembly, rotate bulb anticlockwise and remove from bulb holder. 4. Insert new bulb into bulb holder and rotate it clockwise. 5. Reinstall bulb holder in lamp assembly and reconnect harness connector. 6. Reinstall panel to underside of vehicle using 2 screws removed earlier.
164 Vehicle care Side turn signal lights Centre high-mounted brake light Have bulbs replaced by a workshop. Number plate light 5. Reinstall bulb holder into lamp assembly, rotate bulb holder clockwise and ensure it is secure. 6. Replace lamp covers using the 4 screws removed earlier. Interior lights Front reading lights 1. Using a suitable screwdriver, pry lamp assembly away from wing. 2. Rotate bulb holder anticlockwise. 3. Remove bulb from lamp assembly by pulling bulb straight out of bulb holder.
Vehicle care Rear reading lights Load compartment light 165 Electrical system Fuses 1. Using a suitable screwdriver, pry lamp lens away from roof lining. 2. Remove bulb. 3. Insert new bulb. 4. Reinstall lamp lens in roof lining. 1. Using a suitable screwdriver, remove lens from lamp assembly. 2. Remove bulb. 3. Insert new bulb. 4. Reinstall lens to lamp assembly. Glovebox light Have bulbs replaced by a workshop. Instrument panel illumination Have bulbs replaced by a workshop.
166 Vehicle care It is advisable to carry a full set of spare fuses. Spare fuses can be stored in the engine compartment fuse box. Fuse extractor A fuse extractor may be located in the engine compartment fuse box. Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse.
Vehicle care Engine compartment fuse box The fuse box is located next to the coolant reservoir in the engine compartment. To open, disengage cover and tilt upwards.
168 Vehicle care
Vehicle care 169 Fuse Circuit Fuse Circuit Fuse Circuit ABS Anti-lock Brake System FAN1 Cooling fan LO BEAM RH A/C Climate control, air conditioning system FAN3 Cooling fan Low beam (righthand) FRT FOG Front fog lights PRK LP LH FRT WPR Front wiper Parking light (lefthand) Fuel pump, vacuum pump PRK LP RH Parking light (right-hand) PWM FAN Pulse width modu‐ lation fan BATT1 Instrument panel fuse box FUEL/VAC BATT2 Instrument panel fuse box HDLP WASHER Headlight washer BATT
170 Vehicle care After changing of defective fuses close the fuse box cover and press until it engages. If the fuse box cover is not closed correctly, malfunctions may occur. Instrument panel fuse box The fuse box is located on the lefthand side of the front passenger seat foot well, or, in right-hand drive vehicles, on the left-hand side of the driver's seat foot well. Release latch to open cover.
Vehicle care 171
172 Vehicle care Fuse Circuit Fuse Circuit Fuse Circuit AMP Amplifier CIM HVAC BLWR APO JACK (CONSOLE) Power outlet (centre console) Communica‐ tions Integration Module Climate control, air conditioning fan APO JACK (REAR CARGO) Power outlet (load compart‐ ment) CLSTR Instrument cluster IPC Instrument panel cluster DRL ISRVM/RCM AWD/VENT All-wheel drive, ventilation Daytime running lights DR/LCK Driver door lock Interior mirror, remote compass module BCM (CTSY) Courtesy lights
Vehicle care Fuse Circuit Fuse Circuit Vehicle tools RUN 2 Power battery key on run XBCM Export Body Control Module Tools RUN/CRNK Run crank XM/HVAC/DLC Vehicles with spare wheel SDM (BATT) Safety Diag‐ nosis Module (Battery) XM satellite radio, climate control, data link connection SDM (IGN 1) Safety Diag‐ nosis Module (Ignition) SPARE - S/ROOF Sunroof S/ROOF BATT Sunroof battery SSPS Power steering STR/WHL SW Steering wheel TRLR Trailer TRLR BATT Trailer battery 173 After
174 Vehicle care To remove the jack and vehicle tools, open the tailgate. Remove wing bolt from the jack by rotating it anticlockwise and remove the jack and wheel wrench bag. Remove straps holding the bag containing the wheel wrench. Remove wheel wrench from the bag. Vehicles with tyre repair kit Where present, hang the hook to the upper part of the tailgate opening. Push both levers on the floor cover towards the handle and pull up the cover by the handle.
Vehicle care Wheels and tyres Tyre condition, wheel condition To remove the tyre repair kit, open the tailgate and pull the floor cover handle upwards 3 68. Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor. Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking.
176 Vehicle care V = up to 150 mph W = up to 168 mph Tyre pressure Check the pressure of cold tyres at least every 14 days and before any long journey. Do not forget the spare wheel. This also applies to vehicles with tyre pressure monitoring system. Use the valve cap key to make unscrewing the valve caps easier. The valve cap key is located on the inside of the tank flap. Tyre pressure 3 207. The tyre pressure data refers to cold tyres. It applies to summer and winter tyres.
Vehicle care The current tyre pressures can be shown in the menu item Tyres in the Board Computer menu. Press the BC button on the Infotainment system and select the menu item. The tyre pressure monitoring system automatically detects the vehicle load. A message appears on the information display if inconsistent tyre pressures are detected. In some versions, the message is displayed in abbreviated form.
178 Vehicle care If the tyre pressure is to be reduced or increased, switch off the ignition. Tyre pressures 3 176, 3 207. External high-power radio equipment could disrupt the tyre pressure monitoring system. The tyre pressure monitoring system valve cores and sealing rings must be replaced each time the tyres are changed. For safety reasons it is recommended that the tread depth of the tyres on one axle should not vary by more than 2 mm. Tread depth Check tread depth at regular intervals.
Vehicle care Wheel covers Tyre chains Tyre chains are permitted only on 16 inch wheels. We recommend you consult your service partner. If the use of tyre chains is required after suffering a flat front tyre, fit the temporary spare wheel on the rear axle and transfer one of the rear wheels to the front axle. General The use of tyre chains is not permitted on the temporary spare wheel. Tyre chains are only permitted on the front wheels.
180 Vehicle care 9 Warning Do not drive faster than 50 mph. Do not use for a lengthy period. Steering and handling may be affected. If you have a flat tyre: Apply the electrical parking brake 3 136 and engage first gear, reverse gear or P. The tyre repair kit is in a storage compartment below the floor cover in the load compartment. To remove the tyre repair kit, open the tailgate. Pull the floor cover handle upwards 3 68. Vehicle tools 3 173.
Vehicle care 6. Press the on/off button to turn the tyre repair kit on. The tyre is filled with sealant. The pressure gauge briefly shows a high pressure while the sealant canister is emptying. Then the pressure starts to drop. All of the sealant is pumped into the tyre. Then the tyre is inflated. 7. Inflate the tyre to the recommended inflation pressure using the pressure gauge. The prescribed tyre pressure should be obtained within 10 minutes 3 207.
182 Vehicle care not be driven. Seek the assistance of a workshop. 12. To adjust tyre pressure, screw compressor air hose (arrowed) directly onto tyre valve. 13. Turn the selector switch clockwise to the air only position. Switch on the compressor to inflate the tyre with air only. Note The driving characteristic of the repaired tyre is severely affected, therefore have this tyre replaced. If unusual noise is heard or the compressor becomes hot, turn compressor off for at least 30 minutes.
Vehicle care Make the following preparations and observe the following information: ■ Park the vehicle on a level, firm and non-slippery surface. The front wheels must be in the straightahead position. ■ Apply the electrical parking brake 3 136 and engage first gear, reverse gear or P. ■ Remove the spare wheel 3 185. ■ Never change more than one wheel at a time. ■ Block wheel diagonally opposite the wheel to be changed, by placing wedge blocks or equivalent in front and behind the wheel.
184 Vehicle care 8. Screw on the wheel nuts and tighten slightly by hand by turning clockwise until wheel is held against the hub. 9. Rotate wrench anticlockwise and lower vehicle to the ground. 4. Before positioning the jack, set it to the necessary height by rotating the eye by hand. Position jack at the jacking point located nearest to the wheel concerned so that the jack claw spans the vertical base. Ensure the jack is positioned correctly.
Vehicle care Have the defective tyre renewed and replace temporary spare wheel with a full specification wheel without delay. corresponding speed limits apply, even though no label indicates this. Seek the assistance of a workshop to check the applicable speed limit. Use of the temporary spare wheel could affect driveability, particularly if using winter tyres. Have the defective tyre renewed as soon as possible and have the wheel balanced and fitted to the vehicle.
186 Vehicle care The temporary spare wheel is located in the load compartment below the floor cover and is secured with a screw-in retainer. Push both levers on the floor cover towards the handle and pull up the cover by the handle. Hang the hook to the upper part of the tailgate opening. Vehicle tools 3 173. Remove the retainer by rotating it anticlockwise and remove temporary spare wheel from the spare wheel well. Only mount one temporary spare wheel. Do not drive faster than 50 mph.
Vehicle care Jump starting Do not start with quick charger. A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle. 9 Warning Be extremely careful when starting with jump leads. Any deviation from the following instructions can lead to injuries or damage caused by battery explosion or damage to the electrical systems of both vehicles. 9 Warning Avoid contact of the battery with eyes, skin, fabrics and painted surfaces.
188 Vehicle care 3. Connect the black lead to the negative terminal 3 of the booster battery. 4. Connect the other end of the black lead to a vehicle grounding point, such as the engine block 4 or an engine mounting bolt. Connect as far away from the discharged battery as possible, however at least 60 cm. Route the leads so that they cannot catch on rotating parts in the engine compartment. To start the engine: 1. Start the engine of the vehicle providing the jump start. 2.
Vehicle care Turn key to ignition switch position ACC and release the electrical parking brake before towing the vehicle. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope - or better still a tow rod - to the front towing eye, never to the bumper or front suspension units. Do not tow the vehicle from the rear.
190 Vehicle care Towing another vehicle The towing eye must only be used for towing and not for recovering a vehicle. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. Remove the cover located on the rear bumper by pressing the lower part of the cover. The rear towing eye attachment is stored below the floor cover in the load compartment.
Vehicle care If using a car wash, comply with the car wash manufacturer's instructions. The windscreen wiper and rear window wiper must be switched off. Remove antenna and external accessories such as roof racks etc. If you wash your vehicle by hand, make sure that the insides of the wheel housings are also thoroughly rinsed out. Clean edges and folds on opened doors and the bonnet as well as the areas they cover. Caution Always use a cleaning agent with a pH value of 4 to 9.
192 Vehicle care Wheels and tyres Before and after winter, wash the underbody and have the protective wax coating checked. Do not use high-pressure jet cleaners. Clean rims with a pH-neutral wheel cleaner. Rims are painted and can be treated with the same agents as the body. Towing equipment Paintwork damage Rear carrier system Rectify minor paintwork damage with a touch-up pen before rust forms. Have more extensive damage or rust areas repaired by a workshop.
Vehicle care Plastic and rubber parts Plastic and rubber parts can be cleaned with the same cleaner as used to clean the body. Use interior cleaner if necessary. Do not use any other agent. Avoid solvents and petrol in particular. Do not use highpressure jet cleaners.
194 Service and maintenance Service and maintenance General information ................... 194 Recommended fluids, lubricants and parts .................................... 195 General information Service information In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified.
Service and maintenance Make sure that the Service and Warranty Booklet is completed correctly as continuous proof of service is essential if any warranty or goodwill claims are to be met, and is also a benefit when selling the vehicle. Service interval with remaining engine oil life duration The service interval is based on several parameters depending on usage. The service display lets you know when to change the engine oil. Service display 3 80.
196 Service and maintenance Select the appropriate engine oil based on its quality and on the minimum ambient temperature 3 199. Additional engine oil additives The use of additional engine oil additives could cause damage and invalidate the warranty. Engine oil viscosity The SAE viscosity grade gives information of the thickness of the oil. Multigrade oil is indicated by two figures, e.g. SAE 5W-30.
Technical data Technical data Vehicle identification .................. 197 Vehicle data ............................... 199 197 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is also engraved on the top right-hand side of the bulkhead near the centre of the engine firewall. The Vehicle Identification Number is visible through the windscreen.
198 Technical data Identification plate The identification label is located on the front left door frame.
Technical data 199 Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries (except Belarus, Moldova, Russia, Turkey) Engine oil quality Only Israel Petrol engines (including E85) Diesel engines Petrol engines (including E85) Diesel engines dexos 1 – – ✔ – dexos 2 ✔ ✔ – ✔ In case dexos quality is unavailable you may use max. 1 litre engine oil quality ACEA C3 once between each oil change.
200 Technical data International service schedule Required engine oil quality All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Turkey Petrol engines (including E85) Diesel engines Petrol engines (including E85) Diesel engines dexos 1 ✔ – – – dexos 2 – ✔ ✔ ✔ In case dexos quality is unavailable you may use the oil qualities listed below: All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Turkey Petrol en
Technical data All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Turkey Petrol engines (including E85) Diesel engines Petrol engines (including E85) Diesel engines ACEA A3/B3 ✔ – ✔ – ACEA A3/B4 ✔ ✔ ✔ ✔ ACEA C3 ✔ ✔ ✔ ✔ API SM ✔ – ✔ – API SN resource conserving ✔ – ✔ – Engine oil viscosity grades All countries outside Europe (except Israel), including Belarus, Moldova, Russia, Turkey Ambient temperature Petrol and diesel engines down
202 Technical data Engine data Sales designation 2.4 3.0 V6 2.2 CDTI 2.
Technical data 203 Performance All-wheel drive Engine A 24 XF A 30 XF A 22 DM A 22 DMH Manual transmission 115 – 116 124 Automatic transmission 109 123 113 119 A 24 XF A 30 XF A 22 DM A 22 DMH Manual transmission 118 – 117 – Automatic transmission – – 114 – Maximum speed [mph] 4) Front-wheel drive Engine Maximum speed [mph] 4) 4) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload.
204 Technical data Vehicle weight Kerb weight, basic model without any optional equipment Manual transmission / Automatic transmission.
Technical data Turning circle diameter, wall to wall [m] 12.78 Turning circle diameter, kerb to kerb [m] 11.
206 Technical data Capacities Engine oil Engine A 24 XF A 30 XF A 22 DM A 22 DMH including filter [l] 4.7 5.7 5.6 5.6 between MIN and MAX [l] 1.0 1.0 1.0 1.
Technical data 207 Tyre pressures Up to full load Engine Tyres All 5) 6) Up to full load ECO Trailer towing front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 240/2.4 (35) 240/2.4 (35) 260/2.6 (38) 260/2.6 (38) 240/2.4 (35) 280/2.8 (41) T 155/90 R 166) 420/4.2 (60) (Temporary spare) 420/4.2 (60) – – 420/4.2 (60) 420/4.
208 Customer information Customer information Customer information Customer information ................ 208 Vehicle data recording and pri‐ vacy ........................................... 208 This vehicle has systems that transmit and/or receive radio waves subject to Directive 1999/5/EC. These systems are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Copies of the original Declarations of Conformity can be obtained on our website.
Customer information ■ Vehicle reactions in particular driving situations (e.g. inflation of an airbag, activation of the stability regulation system) ■ Environmental conditions (e.g. temperature) These data are exclusively technical and help identifying and correcting errors as well as optimizing vehicle functions. Motion profiles indicating travelled routes cannot be created with these data. If services are used (e.g.
210 Index A Accessories and vehicle modifications .......................... 150 Accessory sockets........................ 77 Active head restraints............. 33, 34 Adjustable air vents ................... 119 Airbag and belt tensioners ........... 83 Airbag deactivation ...................... 48 Airbag label................................... 43 Airbag system .............................. 43 Air conditioning regular operation ................................ 120 Air conditioning system ............
211 Centre high-mounted brake light.................................. 109, 164 Change engine oil ....................... 88 Changing tyre and wheel size . . . 178 Charging system .......................... 83 Check control................................ 99 Child locks ................................... 21 Child restraint installation locations ................................... 51 Child restraints.............................. 50 Child restraint systems ................ 50 Cleaning the vehicle...........
212 Fuel consumption - CO2Emissions ............................... 145 Fuel economy mode..................... 88 Fuel filler cap................................ 84 Fuel for diesel engines .............. 144 Fuel for petrol engines ............... 143 Fuel gauge ................................... 80 Fuses ......................................... 165 G Gauges......................................... 79 General information ................... 146 Glovebox .....................................
213 N New vehicle running-in .............. 122 Number plate light ..................... 164 O Object detection systems........... 141 Octane rating.............................. 202 Odometer ..................................... 79 Oil............................................... 152 Oil, engine.......................... 195, 199 Oil life monitor............................... 88 Outside temperature .................... 75 Overrun cut-off ........................... 124 P Parking ...................
214 Tailgate open ............................... 90 Tail lights ................................... 163 Technical data............................ 202 Three-point seat belt .................... 41 Tools .......................................... 173 Top-tether fastening eyes ............ 54 Tow bar....................................... 146 Towing................................ 146, 188 Towing another vehicle ............. 190 Towing a trailer........................... 146 Towing equipment ..............
