Owner’s Manual Model Year 2014 Edition: October 2013 KTA-2683/6-VX-en 0-1 VAUXHALL Movano Owner’s Manual Model Year 2014 Edition: October 2013 KTA-2683/6-VX-en
Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 18 Seats, restraints ........................... 35 Storage ........................................ 60 Instruments and controls ............. 68 Lighting ........................................ 87 Climate control ............................. 94 Driving and operating ................. 106 Vehicle care ...............................
2 Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". Thank you for choosing a Vauxhall. We wish you many hours of pleasurable driving.
Introduction 5
6 In brief In brief Vehicle unlocking Unlocking with remote control Unlocking with key Initial drive information Turn the key in the driver's door lock. Open the doors by pulling the handles. Press button c to unlock the front doors. Press again to unlock entire vehicle. Open the doors by pulling the handles. Press button G; only the load compartment and sliding side doors are unlocked. Radio remote control 3 18, Central locking system 3 19, Anti-theft alarm system 3 27.
In brief Seat adjustment Seat backrests Seat height Pull lever, adjust inclination and release lever. Allow the seat to engage audibly. Seat position 3 36, Seat adjustment 3 37. Lever motion up = seat higher down = seat lower 7 Seat positioning Pull handle, slide seat, release handle. Seat position 3 36, Seat adjustment 3 37. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. Seat position 3 36, Seat adjustment 3 37.
8 In brief Head restraint adjustment Seat belt Mirror adjustment Interior mirror Press release catch, adjust height, engage. Head restraints 3 35. Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle. Seat position 3 36, Seat belts 3 43, Airbag system 3 45.
In brief Exterior mirrors 9 Electric adjustment Steering wheel adjustment Select the relevant exterior mirror and adjust it. Convex exterior mirrors 3 30, Electric adjustment 3 30, Folding exterior mirrors 3 30, Heated exterior mirrors 3 31. Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked. Do not adjust steering wheel unless vehicle is stationary and steering wheel lock has been released. Airbag system 3 45, Ignition positions 3 107.
10 In brief Instrument panel overview
In brief 1 2 Fixed air vents .................... 104 Headlight range adjustment ........................... 88 Ultrasonic parking assist ..... 124 6 Horn ..................................... 69 7 Driver airbag ........................ 49 Remote control on steering wheel ....................... 68 8 Cruise control ..................... 121 Windscreen wiper, windscreen washer system .. 69 Traction control system ...... 119 3 4 Electronic stability program 120 Side air vents .....................
12 In brief Exterior lighting Front and rear fog lights Turn light switch: = Off 7 = Sidelights 0 9 P = Headlights AUTO = Automatic light control: Headlights are switched on and off automatically. = Front fog lights > = Rear fog lights r Turn light switch: > = Front fog lights r = Rear fog lights Lighting 3 87, Headlight warning device 3 84, Adaptive forward lighting 3 89. Headlight flash, high beam and low beam Pull lever. High beam 3 88, Headlight flash 3 88.
In brief Turn and lane-change signals Hazard warning flashers Horn lever up = right turn signal lever down = left turn signal Operated with the ¨ button. Hazard warning flashers 3 89. Press j. Turn and lane-change signals 3 89.
14 In brief Washer and wiper systems Windscreen washer Windscreen wiper 0 = off P = timed interval wiping or automatic wiping with rain sensor 1 = slow 2 = fast Windscreen wiper, automatic wiping with rain sensor 3 69, Wiper blade replacement 3 139. Climate control Heated rear window, heated exterior mirrors Pull lever.
In brief Demisting and defrosting the windows ■ Air distribution to V. ■ Set temperature control to warmest level. ■ Set fan speed to highest level. ■ Cooling AC on. ■ Press button Ü. Climate control system 3 94. Vehicles with Electronic climate control, press button V. Temperature and air distribution are set automatically and the fan runs at a high speed. Electronic climate control system 3 96.
16 In brief Manual transmission automated Starting off Starting the engine Check before starting off N o + A/M R = = = = = neutral drive higher gear lower gear switch between automatic and manual mode = reverse gear Manual transmission automated 3 114. ■ Tyre pressure and condition 3 152, 3 189. ■ Engine oil level and fluid levels 3 134. ■ All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and are operational.
In brief Stop-start system Parking Caution Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface. If the vehicle is at low speed or in standstill and certain conditions are fulfilled, activate an Autostop as follows: ■ Depress the clutch pedal ■ shift the selector lever to N ■ release the clutch pedal An Autostop is indicated when Ï illuminates green in the instrument cluster. To restart the engine, depress the clutch pedal again.
18 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 18 Doors ........................................... 24 Vehicle security ............................ 27 Exterior mirrors ............................ 30 Interior mirrors ............................. 31 Windows ...................................... 32 Roof .............................................
Keys, doors and windows Handle with care, protect it from moisture and high temperatures and avoid unnecessary operation. Fault If the central locking system cannot be operated with the remote control, it may be due to the following: ■ Range exceeded. ■ Battery voltage too low. ■ Frequent, repeated operation of the remote control while not in range, which will require reprogramming by a workshop. ■ Interference from higher-power radio waves from other sources. Unlocking 3 19.
20 Keys, doors and windows Unlocking the vehicle Unlocking with 2-button remote control Unlocking with 3-button remote control Locking the vehicle Close all doors and load compartment. If the doors are not closed properly, the central locking system will not work. Locking with 2-button remote control Press button c: All doors and the load compartment are unlocked. Depending on vehicle configuration: ■ Press button c: Front doors are unlocked.
Keys, doors and windows Locking with 3-button remote control Load compartment Locking and unlocking load compartment with 2-button remote control Press button e: All doors and the load compartment are locked. Note Where fitted, alarm monitoring of the passenger compartment 3 27 is switched off by pressing and holding button e (which is confirmed by an audible signal). If this was done unintentionally, unlock the doors again and press button e briefly to lock the vehicle.
22 Keys, doors and windows Fault in central locking system Unlocking Manually unlock the front door by turning the key in the lock. The other doors can be opened by pulling the interior handles. Press the e switch to lock or unlock. LED in switch illuminates when the vehicle is locked. Fault in remote control system Unlocking Manually unlock the front door by turning the key in the lock. Switch on the ignition and press the central locking switch e to open all doors and the load compartment.
Keys, doors and windows Child locks Warning lights in the appropriate doors remain illuminated. To unlock, press 0 side of switch. Fault In the event of a fault in the system, the warning light alongside the switch remains illuminated and an audible warning will sound. Check the doors are manually unlocked (interior door lock switches). If necessary, have the cause of the fault remedied by a workshop.
24 Keys, doors and windows Doors Power sliding door Sliding door Opening Closing Press switch again; the LED flashes and a chime sounds during operation. In the event of opening or closing difficulties, e.g. due to frost, press and hold the switch to increase power to the sliding door. 9 Warning Open and close the sliding side door only when the vehicle is at a standstill with the parking brake applied.
Keys, doors and windows 25 Emergency exit Maintenance Power side step In an emergency, the door can be opened manually after releasing the interior handle. It is the owner's responsibility to have the drive belt replaced after every 15,000 cycles, and for this purpose a counter is incorporated in the lower Bpillar. Seek the assistance of a workshop. If the drive belt should fail, the door may still be opened and closed manually.
26 Keys, doors and windows The indicator illuminates during operation of the power side step. If it remains illuminated with the door closed, the step has not retracted. In this event, manually retract the power side step by pulling the declutching mechanism located behind the step. Seek the assistance of a workshop. Rear doors To open the right-hand rear door, pull the outside handle. The door is opened from inside the vehicle by pulling the interior handle.
Keys, doors and windows When opening the doors to 270º, the doors are retained in the fully open position by magnets on the body side. 9 Warning Ensure extended opening doors are secured when fully opened. Opened doors may slam closed due to the force of the wind! When closing the doors, secure each locking stay to the catch on the door frame. Close the left-hand door before the right-hand door.
28 ■ ■ ■ ■ Keys, doors and windows Load compartment Vehicle inclination, e.g. if it is raised Ignition Interruption of alarm siren power supply Activation All doors and the bonnet must be closed. Deactivation Unlocking the vehicle or switching on the ignition deactivates the anti-theft alarm system. Hazard warning lights flash once to confirm deactivation. Note If the alarm has been triggered, unlocking the vehicle with the key will not stop the alarm siren. To stop the siren, switch on the ignition.
Keys, doors and windows Activation without monitoring of vehicle inclination Additionally, disable monitoring of vehicle inclination because of high volume ultrasonic signals or movements triggering the alarm, e.g. when the vehicle is on a ferry or train: Switch ignition on and off three times in quick succession, then close doors and activate the anti-theft alarm system. An audible signal will sound as confirmation. The status will remain until the doors are unlocked.
30 Keys, doors and windows Exterior mirrors Electric adjustment Folding mirrors Select the relevant exterior mirror by switching the control to the left or right, then swivel the control to adjust the mirror. No mirror is selected when the control is in the centre position. The lower mirrors are not adjustable. For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force.
Keys, doors and windows Heated mirrors Heating works with the engine running and is switched off automatically after a short time. Climate control system 3 94. Electronic climate control system 3 96. 31 Interior mirrors Manual anti-dazzle Operated by pressing the Ü button on either system. To reduce dazzle, adjust the lever on the underside of the mirror housing.
32 Keys, doors and windows Windows Overload If the windows are repeatedly operated within short intervals, the window operation is disabled for some time. Manual windows The door windows can be opened or closed with the window winders. Rear windows Power windows Sliding side windows 9 Warning Take care when operating the power windows. Risk of injury, particularly to children. Keep a close watch on the windows when closing them. Ensure that nothing becomes trapped in them as they move.
Keys, doors and windows Press catch and slide window to open. Ensure catch engages when closing. 33 Opening side windows Emergency exit Pull handle to open window. To provide an emergency exit from the vehicle, use hammer 1 to strike glass 2.
34 Keys, doors and windows Heated rear window Heating works with the engine running and is switched off automatically after a short time. Climate control system 3 94. Electronic climate control system 3 96. Roof Glass panel Emergency exit Sun visors Operated by pressing the Ü button on either system. The sun visors can be folded down or swivelled to the side to prevent dazzling. If the sun visors have integral mirrors, the mirror covers should be closed when driving.
Seats, restraints Seats, restraints Head restraints ............................ 35 Front seats ................................... 36 Rear seats ................................... 41 Seat belts ..................................... 43 Airbag system .............................. 45 Child restraints ............................. 51 Head restraints 35 Height adjustment Position 9 Warning Only drive with the head restraint set to the proper position.
36 Seats, restraints Removal Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. Press both catches, pull the head restraint upwards and remove. Stow head restraints securely in load compartment. Do not drive with head restraints removed if the seat is occupied. ■ Sit with buttocks as far back against the backrest as possible. Adjust the distance between the seat and the pedals so that legs are slightly angled when pressing the pedals.
Seats, restraints Seat adjustment 9 Danger Pull handle, slide seat, release handle. Seat backrests Suspension seat positioning Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat positioning Pull handle, slide seat, release handle. Pull lever, adjust inclination and release lever. Allow the seat to engage audibly.
38 Seats, restraints Suspension seat backrests Seat height Suspension seat height Pull lever, adjust inclination and release lever. Allow the seat to engage audibly. Lever pumping motion up = seat higher down = seat lower Pull up front release lever up to adjust height of front part of seat. Pull up rear release lever to adjust height of rear part of seat.
Seats, restraints 39 Lumbar support Suspension seat lumbar support Suspension seat sensitivity Adjust lumbar support to suit personal requirements. Increasing and decreasing support: turn the handwheel while relieving the load on the backrest. Adjust lumbar support to suit personal requirements. Operate hand pump repeatedly (located on underside of unit) to increase firmness. Press release button (located at front of unit) to decrease firmness.
40 Seats, restraints Armrest Heating Armrest can be folded up when not required. Press the ß button for the respective seat. Press the ß button again to switch off. Seat heating is thermostatically controlled and switches off automatically when seat temperature is sufficient. Control indicator in the button illuminates when the system is on, not just when heating is active. Prolonged use of the highest setting for people with sensitive skin is not recommended.
Seats, restraints Rear seats Removable rear seats Rear seat access Removal On some variants, the cargo area can be increased by removing the rear seats. 41 9 Warning Removable rear seats are heavy! Do not attempt to remove without assistance. Installation Caution The rear seats are not interchangeable and must be fitted back into their original position. To facilitate access to the rear seats, pull release lever and fold the seat backrest forwards.
42 Seats, restraints Position the seat guides immediately behind the front floor anchor points, and slide forwards to engage. Bus Removal Using the tool from the tool kit located in the glovebox, turn levers to unlock the seat. 9 Warning Removable rear seats are heavy! Do not attempt to remove without assistance. Installation 1. Position the seat over the anchor points. 2. Lower the seat until it engages. 3. Ensure the seat is locked securely in position.
Seats, restraints Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle, holding the occupants in the sitting position. Therefore, the risk of injury is considerably reduced. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves. Seat belts are designed to be used by only one person at a time. Child restraint system 3 51.
44 Seats, restraints Three-point seat belt Height adjustment Fastening Withdraw the belt from the retractor, guide it untwisted across the body and insert the latch plate into the buckle. Tighten the lap belt regularly whilst driving by pulling the shoulder belt. Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body.
Seats, restraints Removing Using the seat belt while pregnant 45 Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning To release belt, press red button on belt buckle. 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen.
46 Seats, restraints Each airbag is triggered only once. Have deployed airbags replaced by a workshop. Furthermore, it may be necessary to have the steering wheel, the instrument panel, parts of the panelling, the door seals, handles and the seats replaced. Do not make any modifications to the airbag system as this will invalidate the vehicle type approval. When the airbags inflate escaping hot gases may cause burns. Control indicator v for airbag systems 3 78.
Seats, restraints DA: Brug ALDRIG en bagudvendt autostol på et forsæde med AKTIV AIRBAG, BARNET kan komme I LIVSFARE eller komme ALVORLIGT TIL SKADE. SV: Använd ALDRIG en bakåtvänd barnstol på ett säte som skyddas med en framförvarande AKTIV AIRBAG. DÖDSFALL eller ALLVARLIGA SKADOR kan drabba BARNET. FI: ÄLÄ KOSKAAN sijoita taaksepäin suunnattua lasten turvaistuinta istuimelle, jonka edessä on AKTIIVINEN TURVATYYNY, LAPSI VOI KUOLLA tai VAMMAUTUA VAKAVASTI.
48 Seats, restraints BLAZINO, saj pri tem obstaja nevarnost RESNIH ali SMRTNIH POŠKODB za OTROKA. SR: NIKADA ne koristiti bezbednosni sistem za decu u kome su deca okrenuta unazad na sedištu sa AKTIVNIM VAZDUŠNIM JASTUKOM ispred sedišta zato što DETE može da NASTRADA ili da se TEŠKO POVREDI. MK: НИКОГАШ не користете детско седиште свртено наназад на седиште заштитено со АКТИВНО ВОЗДУШНО ПЕРНИЧЕ пред него, затоа што детето може ДА ЗАГИНЕ или да биде ТЕШКО ПОВРЕДЕНО.
Seats, restraints Front airbag system The front airbag system consists of one airbag in the steering wheel and one in the instrument panel on the front passenger side. These can be identified by the word AIRBAG. The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and head of the front seat occupants considerably. Side airbag system 9 Warning Optimum protection is only provided when the seat is in the proper position 3 36.
50 Seats, restraints 9 Warning Keep the area in which the airbag inflates clear of obstructions. Note Only use protective seat covers that have been approved for the vehicle. Be careful not to cover the airbags. Airbag deactivation Front airbag and side airbag systems for the front passenger seat must be deactivated if a child restraint system is to be fitted on this seat. The belt pretensioners and all driver airbag systems will remain active.
Seats, restraints As long as control indicator * is not illuminated, the airbag systems for the front passenger seat will inflate in the event of a collision. If control indicator A remains illuminated together with v, this indicates a fault within the system. Seek the assistance of a workshop. Change status only when the vehicle is stopped with the ignition off. Status remains until the next change. Control indicator for airbag deactivation 3 78.
52 Seats, restraints Ensure that the mounting location of the child restraint system within the vehicle is correct. Allow children to enter and exit the vehicle only on the side facing away from the traffic. When the child restraint system is not in use, secure the seat with a seat belt or remove it from the vehicle. Note Do not affix anything on the child restraint systems and do not cover them with any other materials.
Seats, restraints 53 Child restraint installation locations Permissible options for fitting a child restraint system Front seats - All variants Weight and age class Group 0: up to 10 kg or approx. 10 months Group 0+: up to 13 kg or approx. 2 years Group I: 9 to 18 kg or approx. 8 months to 4 years Group II: 15 to 25 kg or approx. 3 to 7 years Group III: 22 to 36 kg or approx.
54 Seats, restraints Crew cab - rear seats Weight and age class Group 0: up to 10 kg or approx. 10 months Group 0+: up to 13 kg or approx. 2 years Group I: 9 to 18 kg or approx. 8 months to 4 years Group II: 15 to 25 kg or approx. 3 to 7 years Group III: 22 to 36 kg or approx.
Seats, restraints 55 Combi - rear seats Weight and age class 2nd row seats 3rd row seats Driver side outer seat Centre seat Passenger side outer seat Group 0: up to 10 kg or approx. 10 months Group 0+: up to 13 kg or approx. 2 years U3), < X X X Group I: 9 to 18 kg or approx. 8 months to 4 years U4), < UF4), < UF4) X Group II: 15 to 25 kg or approx. 3 to 7 years Group III: 22 to 36 kg or approx.
56 Seats, restraints Bus - rear seats Weight and age class Rear seats Group 0: up to 10 kg or approx. 10 months Group 0+: up to 13 kg or approx. 2 years X Group I: 9 to 18 kg or approx. 8 months to 4 years Group II: 15 to 25 kg or approx. 3 to 7 years Group III: 22 to 36 kg or approx. 6 to 12 years U X X = Suitable for universal category restraint systems for use in this weight and age class, in conjunction with three-point seat belt.
Seats, restraints 57 Permissible options for fitting an ISOFIX child restraint system Combi Weight class Size class Fixture Front seats 2nd row seats 3rd row seats Driver side Passenger side outer seat Centre seat outer seat Group 0: up to 10 kg or approx. 10 months E ISO/R1 X IL X X X Group 0+: up to 13 kg or approx. 2 years E ISO/R1 X IL X X X D ISO/R2 X IL X X X C ISO/R3 X IL X X X Group I: 9 to 18 kg D or approx.
58 Seats, restraints ISOFIX size class and seat device A - ISO/F3 B - ISO/F2 B1 - ISO/F2X C - ISO/R3 D - ISO/R2 E - ISO/R1 = = = = = = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. When using ISOFIX mounting brackets for seat mounting, universally approved child restraint systems for ISOFIX may be used. Permissible mounting location positions for ISOFIX child restraint systems are marked in the tables by <, IL and IUF. Top-tether fastening eyes Top-Tether fastening eyes are located on the back of the seat.
60 Storage Storage Storage compartments ................ 60 Load compartment ....................... 63 Roof rack system ......................... 66 Loading information ..................... 66 Storage compartments 9 Warning Do not store heavy or sharp objects in the storage compartments. Otherwise, the storage compartment lid could open and vehicle occupants could be injured by objects being thrown around in the event of hard braking, a sudden change in direction or an accident.
Storage To fold away, raise the base until the document holder is horizontal, then push fully in. Glovebox The cupholders can also be used to hold the portable ashtray unit 3 72. Front storage Three coat hooks are located on the cabin bulkhead The front door pockets contain bottle holders. 61 The swivelling shelf, which can be used for writing or documents, must be returned to its original position before raising the seat backrest.
62 Storage Overhead console Underseat storage Overcab storage The total weight in these compartments must not exceed 5 kg. Using the two loops on the passenger seat cushion, pull the cushion forwards to gain access to the storage under the seat. The total weight in this compartment must not exceed 35 kg. Rear storage Bus Objects can be stored in the overhead storage racks above the rear passenger seating. The total weight in each storage rack must not exceed 35 kg.
Storage Load compartment 63 Removable lashing eyes Lashing eyes Lashing eyes are mounted in the load compartment to enable cargo to be secured in position using lashing straps or a luggage floor net. The maximum force applied to the lashing eyes should not exceed 5000 N at 30°. To reposition, press down on the centre cap and slide to the desired position. Ensure the lashing eye engages correctly in the recess. Loading information 3 66.
64 Storage Store the partition wall to one side of the load compartment when not in use. Telescopic blocking bars Ratchet straps Using the appropriate ratchet straps, objects can be secured to the removable lashing eyes in the side or floor load rails. The maximum loading for the side rails is 100 daN/700mm. Removable lashing eyes 3 63, Loading information 3 66. The telescope blocking bars can be used in a vertical or horizontal position.
Storage Safety net 65 Underseat storage 3 62. First aid kit The first aid kit can be accommodated in the space under the front seats or in the overhead console. A label is located on the overhead console should the first aid kit be stored there. Underseat storage 3 62. Overhead console 3 62. Lower the safety net from the roof area and attach to the lashing eyes 3 63. Adjust the tension on the straps to ensure the load is secure. When not in use the safety net should be stored in the roof area.
66 Storage An additional extinguisher may be located in the front door panel. As a visible indication of this, a label is located on the overhead console. Roof rack system Loading information Roof rack ■ Heavy objects in the load compartment should be evenly distributed and placed as far forward as possible. If objects can be stacked, the heavier objects should be placed at the bottom. ■ Secure objects with lashing straps attached to lashing eyes 3 63.
Storage 9 Warning Always make sure that the load in the vehicle is securely stowed. Otherwise objects can be thrown around inside the vehicle and cause personal injury or damage to the load or car. ■ The payload is the difference between the permitted gross vehicle weight (see identification plate 3 171) and the EC kerb weight. To calculate the EC kerb weight, enter the data for your vehicle in the Weights table at the front of this manual.
68 Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Controls ....................................... 68 Warning lights, gauges and indi‐ cators ........................................... 73 Information displays ..................... 83 Vehicle messages ........................ 83 Trip computer ............................... 85 Tachograph ..................................
Instruments and controls Horn Windscreen wiper/washer 69 Automatic wiping with rain sensor Windscreen wiper Press j. The horn will sound regardless of ignition switch position. Steering column controls The Infotainment system can also be operated via the controls on the steering column. Further information is available in the Infotainment system manual. K = Automatic wiping with rain sensor K = timed interval wipe 1 = slow 2 = fast Do not use if the windscreen is frozen. Switch off in car washes.
70 Instruments and controls Adjustable sensitivity of the rain sensor Turn the adjuster wheel to adjust the sensitivity: Low = turn adjuster wheel sensi‐ downwards tivity High = turn adjuster wheel sensi‐ upwards tivity Keep the sensor free from dust, dirt and ice. Windscreen washer Outside temperature Pull lever. Washer fluid is sprayed onto the windscreen.
Instruments and controls 9 Warning The road surface may already be icy even though the display indicates a few degrees above 0 °C. Clock Depending on vehicle, the current time and/or date may appear in the information display 3 83 or the Driver Information Centre 3 83. Hours and minutes can be adjusted by pressing the appropriate buttons by the display or with the Infotainment system controls. Further information is available in the Infotainment system manual.
72 Instruments and controls Connecting electrical accessories while the engine is off will discharge the vehicle battery. Do not exceed the maximum power consumption of 120 watts. Electrical accessories that are connected must comply with the electromagnetic compatibility requirements laid down in DIN VDE 40 839. Do not connect any current-delivering accessories, e.g. electrical charging devices or batteries. Do not damage the outlet by using unsuitable plugs.
Instruments and controls Warning lights, gauges and indicators Instrument cluster In some versions, the needles of the instruments briefly rotate to the end position when the ignition is switched on. Speedometer Maximum speed may be restricted by a speed regulator. As a visible indication of this, a warning label is located on the instrument panel. A warning buzzer will sound for 10 seconds if the vehicle briefly exceeds the set limit. Note Under certain conditions (e.g.
74 Instruments and controls Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Caution If the needle is in the red warning zone, the maximum permitted engine speed is exceeded. Engine at risk. Fuel gauge Control indicator Y illuminates if the level in the tank is low. Refuel immediately 3 127. Never run the tank dry. Diesel fuel system, bleeding 3 139.
Instruments and controls If the engine oil level is correct when the ignition is switched on OIL LEVEL CORRECT appears briefly in the Driver Information Centre. If the engine oil is above the minimum level, press the trip computer button on the end of the wiper lever within 30 seconds of switching on the ignition. The message OIL LEVEL is displayed in combination with the squares that correspond to the oil level. As the oil level diminishes, the squares in the display are replaced with dashes.
76 kg V T W Instruments and controls = = = = Laden mode Winter mode Apply footbrake Transmission electronics Manual transmission automated 3 114. Control indicators The control indicators described are not present in all vehicles. The description applies to all instrument versions. Depending on the equipment, the position of the control indicators may vary. When the ignition is switched on, most control indicators will illuminate briefly as a functionality test.
Instruments and controls Control indicators in the instrument cluster 77
78 Instruments and controls Turn signal O flashes green. Flashes if a turn signal or the hazard warning flashers are activated. Rapid flashing: failure of a turn signal light or associated fuse. An audible warning can be heard when the turn signals are on. When towing a trailer, the pitch of the audible warning changes. Bulb replacement 3 140. Fuses 3 148. Turn signals 3 89. Seat belt reminder X illuminates red. If the seat belt is not fastened, X will flash when vehicle speed exceeds approx. 10 mph.
Instruments and controls Illuminates when the engine is running Stop, switch off engine. Vehicle battery is not charging. Engine cooling may be interrupted. The brake servo unit may cease to be effective. Seek the assistance of a workshop. Malfunction indicator light Z illuminates or flashes yellow. Illuminates briefly when the ignition is switched on. Illuminates when the engine is running Fault in the emission control system. The permitted emission limits may be exceeded.
80 Instruments and controls 9 Warning Stop. Do not continue your journey. Consult a workshop. Brake system 3 118. Brake pad wear F illuminates yellow. Illuminates when the brake pads are worn 3 118. Seek the assistance of a workshop. Antilock brake system (ABS) u illuminates yellow. Illuminates briefly when the ignition is switched on. The system is ready for operation when u extinguishes.
Instruments and controls Caution Coolant temperature too high. Check coolant level 3 135. If there is sufficient coolant, consult a workshop. Preheating ! illuminates yellow. Preheating is activated. Only activates when outside temperature is low. Diesel particle filter 8 Not used. Diesel particle filter 3 79, 3 112. Engine oil pressure I illuminates red. Illuminates briefly when the ignition is switched on. Illuminates when the engine is running Caution Engine lubrication may be interrupted.
82 Instruments and controls Illuminates when the engine is running High beam Indicates the presence of water in the diesel. Seek the assistance of a workshop immediately. P illuminates blue. Illuminated when high beam is on and during headlight flash 3 88. Stop-start system Fog light Ï illuminates or flashes yellow / green. Illuminates Illuminates green during an Autostop. If Ï illuminates yellow there is a fault in the stop-start system. Seek the assistance of a workshop.
Instruments and controls Information displays Triple-Info-Display Driver Information Centre 83 Vehicle messages Messages appear in the Driver Information Centre, in combination with control indicator A or C.
84 Instruments and controls remains illuminated. The fault will then be stored in the on board system. Warning messages Fault messages ENGINE OVERHEATING CHECK GEARBOX Warning chimes ■ If the vehicle speed briefly exceeds a set limit. ■ During closing of the power sliding door. ■ If the sliding door is open and the parking brake is released. ■ During activation and deactivation of alarm monitoring of vehicle inclination.
Instruments and controls Trip computer The trip computer provides information on driving data, which is continually recorded and evaluated electronically. ■ ■ ■ ■ ■ Distance travelled Average speed Distance before service Clock Cruise control and speed limiter stored speed ■ Fault and information messages Fuel used Displays the amount of fuel consumed since the last reset. The measurement can be restarted at any time by pressing and holding button.
86 Instruments and controls The average speed since the last reset is displayed. The measurement can be restarted at any time. Interruptions in the journey with the ignition off are not included in the calculations. Interruption of power supply If the power supply has been interrupted or if the vehicle battery voltage has dropped too low, the values stored in the trip computer will be lost.
Lighting Lighting Exterior lighting 87 Automatic light control Light switch Exterior lighting ............................ 87 Interior lighting ............................. 90 Lighting features .......................... 92 Turn light switch: = Off 7 = Sidelights 0 9 P = Headlights AUTO = Automatic light control = Front fog lights > = Rear fog lights r High beam control indicator P 3 82. Low beam control indicator 9 3 82.
88 Lighting High beam Headlight range adjustment Manual headlight range adjustment To change between low and high beam, pull lever until a click is felt. Headlight flash To activate the headlight flash, pull lever. Headlights when driving abroad The asymmetrical headlight beam extends visibility at the edge of the road at the passenger side. However, when driving in countries where traffic drives on the opposite side of the road, adjust the headlights to prevent dazzling of oncoming traffic.
Lighting Adaptive forward lighting Cornering light Turn and lane-change signals Depending on the steering angle, vehicle speed and gear selected when cornering, an additional light will illuminate the corner of the road. 89 If the lever is moved past the first stop, the indicator is switched on constantly. Switch the indicator off manually by moving the lever to its original position.
90 Lighting Rear fog lights Misted light covers The inside of the light covers may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing. The mist disappears quickly by itself; to help, switch on the headlights. Interior lighting Interior lights With the switch in its central position, the light functions as a courtesy light and illuminates when the front doors are opened. When the front doors are closed, the courtesy light extinguishes after a delay.
Lighting The courtesy light extinguishes immediately when the ignition is switched on. Rear courtesy lights Bus Low level and overhead courtesy lights are located in the rear passenger compartment. Operate rocker switch on the instrument panel: Press c = on Press OFF = off Load compartment lighting Load compartment lighting can be set to illuminate when the side and rear doors are opened, or switched on constantly.
92 Lighting Rear reading lights Lighting features Bus Exit lighting Each reading light can then be operated individually and directed as required. Operate rocker switch on the instrument panel: press l = on. press OFF = off. Headlights come on for approx. 1 minute after the vehicle is parked and the system is activated. Activating 1. Switch off ignition. 2. Remove ignition key. 3. Pull turn signal lever towards steering wheel.
Lighting This action can be repeated up to four times to a maximum period of 4 minutes. The lighting is turned off immediately by turning the light switch to any position and returning to 7.
94 Climate control Climate control Climate control systems ............... 94 Air vents ..................................... 103 Maintenance .............................. 104 Climate control systems Heating and ventilation system Temperature red = warm blue = cold Heating will not be fully effective until the engine has reached normal operating temperature. Fan speed Adjust the air flow by switching the fan to the desired speed.
Climate control ■ Switch on heated rear window Ü. ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J. Air conditioning system Additional to the heating and ventilation system, the air conditioning system has controls for: AC = cooling u = air recirculation Heated rear window Ü 3 34, Heated seats ß 3 40. Cooling (AC) Operated with the AC button and functional only when the engine and fan are running.
96 Climate control Demisting and defrosting the windows ■ Switch cooling n on. ■ Set temperature control to warmest level. ■ Set fan speed to highest level. ■ Set air distribution control to V. ■ Switch on heated rear window Ü. ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J.
Climate control red = warm blue = cold Heating will not be fully effective until the engine has reached normal operating temperature. If the minimum temperature of 15 ℃ is set, the electronic climate control system runs at maximum cooling. If the maximum temperature of 27 ℃ is set, the electronic climate control system runs at maximum heating. Fan speed The selected fan speed is indicated with x in the display. If the fan is switched off the air conditioning is also deactivated.
98 Climate control During operation, power from the vehicle battery is used. For short journey times, check the vehicle battery regularly and recharge if necessary. To ensure efficient performance, the low level air vents in the rear passenger compartment must not be obstructed. 9 Warning Do not operate the system when refuelling, when dust or combustible vapours are present or in enclosed spaces (e.g. garage). Setting the time and day Press button Ö until the time display flashes.
Climate control Neutral position or no stored programme activated Press P button until their is no stored programme number visible in the display. Bus 99 Fan speed Rear air vents Adjusting the temperature To adjust the temperature of the heating, turn the rotary knob located on the control panel.
100 Climate control With the front passenger compartment air conditioning system switched on, adjust the air flow to select the desired speed. Ensure the air vents are open when in use, to prevent ice forming in the system due to lack of air movement. Auxiliary heater Coolant heater The Eberspächer engineindependent, fuel-powered coolant heater provides rapid heating of the engine coolant to enable heating of the vehicle interior without the engine running.
Climate control Remote control 9 Warning When refuelling, switch off the remote control unit as well as the heater! The control buttons operate identically to the timer unit described previously. To activate the remote control, press activation button X and release it when the menu bar appears in the display. The signal indicator and SENd appear briefly in the display, followed by the temperature. To switch off, press and hold activation button X to prevent inadvertent operation.
102 Climate control Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point.
Climate control Pressing button X during the procedure will exit without storing programme adjustments. To delete a preset departure time, follow the steps for programming until heating symbol Y flashes. Press button q or r until oFF appears in the display and confirm. Heating stops automatically 5 minutes after the programmed departure time.
104 Climate control Side air vents Fixed air vents Additional air vents are located beneath the windscreen and door windows and in the foot wells. Maintenance Air intake Glovebox cooler The air conditioning system can also keep the contents of the glovebox cool. Press the vent to open. Direct the flow of air by swivelling the vent. Depending upon the position of the temperature control, air will be directed into the vehicle via the side air vents.
Climate control Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low.
106 Driving and operating Driving and operating Driving hints Control of the vehicle Driving hints ............................... 106 Starting and operating ............... 106 Engine exhaust .......................... 112 Manual transmission .................. 113 Manual transmission automa‐ ted .............................................. 114 Brakes ........................................ 118 Ride control systems ................. 119 Driver assistance systems ......... 121 Fuel ..................
Driving and operating Ignition switch positions Starting the engine St = Ignition off A = Steering wheel lock released, ignition off M = Ignition on, for diesel engine: preheating D = Starting Manual transmission: operate clutch. Manual transmission automated: operate brake; transmission automatically shifts to N. Do not accelerate. Turn the key to position M for preheating, until control indicator N extinguishes from the Driver Information Centre. Turn key to position D and release.
108 Driving and operating Idle speed control Overrun cut-off Deactivation The fuel supply is automatically cut off during overrun, i.e. when the vehicle is driven with a gear engaged but accelerator is released. Stop-start system To increase the idle speed press the switch. After a few seconds the function will be activated.
Driving and operating The engine will be switched off while the ignition stays on if the required conditions are met. An Autostop is indicated when Ï illuminates green in the instrument cluster. During an Autostop, the brake performance will be maintained. Conditions for an Autostop The stop-start system checks if each of the following conditions is fulfilled, otherwise an Autostop will be inhibited.
110 Driving and operating If the selector lever is shifted out of N before depressing the clutch first, a restart will not take place. Restart of the engine by the stop-start system The selector lever has to be in N to enable an automatic restart. If one of the following conditions occurs during an Autostop, the engine will be restarted automatically by the stop-start system. Control indicator Ï will flash green in the instrument cluster during an automatic engine restart.
Driving and operating Master switch Remote control Caution Handle with care, protect from moisture and high temperatures and avoid unnecessary operation. Pre-programmed settings The air suspension system must be switched off when the vehicle is being towed, jump‐started, raised off the ground or transported. Do not switch off the air suspension system when driving. The master switch is located on the door pillar. 111 Adjusts the suspension height to one of three pre-programmed positions.
112 Driving and operating Service mode Press button i for 5 seconds to put the vehicle into service mode. The indicator light will illuminate. When service mode has been activated, the air suspension master switch must be turned off. To exit service mode, press button i again for 5 seconds. Fault If a fault is detected, i button will flash intermittently. If the service mode has been activated and there is a fault h, S and R buttons will flash simultaneously.
Driving and operating Caution Malfunction indicator light 3 79. 113 Manual transmission Fuel grades other than those listed on page 3 127, 3 174 could damage the catalytic converter or electronic components. Unburnt petrol will overheat and damage the catalytic converter. Therefore avoid excessive use of the starter, running the fuel tank dry and starting the engine by pushing or towing.
114 Driving and operating Caution It is inadvisable to drive with hand resting on the selector lever. Manual transmission automated The manual transmission automated (MTA) permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control. Transmission display Starting the engine Depress the foot brake when starting the engine. If the foot brake is not depressed, T illuminates in the transmission display and the engine cannot be started.
Driving and operating Always move the selector lever in the appropriate direction as far as it will go. Upon release, it automatically returns to the centre position. N = Neutral. A/ = Switch between automatic M and manual mode. The transmission display shows "A" when in automatic mode. R = Reverse gear. Engage only when vehicle is stationary. The transmission display shows "R" when reverse gear is engaged. + = Shift to a higher gear. = Shift to a lower gear.
116 Driving and operating Rocking the vehicle Rocking the vehicle is only permissible if the vehicle is stuck in sand, mud, snow or a hole. Move the selector lever between R and A/M (or between + and -) in a repeat pattern, while applying light pressure to the accelerator pedal. Do not race the engine and avoid sudden acceleration. Parking Apply the parking brake. The most recently engaged gear (see transmission display) remains engaged. With N, no gear is engaged.
Driving and operating Deactivation The Winter mode is switched off by: ■ pressing the V button again, ■ turning off the ignition, ■ switching to manual mode. In order to protect the transmission at extremely high clutch temperatures, an intermittent audible warning may sound. In such cases, depress the foot brake, select "N" and apply the parking brake to allow the clutch to cool down. Laden mode kg It is possible to use the Laden mode in both manual and automatic modes.
118 Driving and operating Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when you depress the brake pedal firmly. You need to use considerably more force for this. The braking distance is extended. Seek the assistance of a workshop before continuing your journey.
Driving and operating Parking brake Brake assist If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied (full braking). Maintain steady pressure on the brake pedal for as long as full braking is required. Maximum brake force is automatically reduced when the brake pedal is released. Always apply parking brake firmly without operating the release button, and apply as firmly as possible on a downhill or uphill slope.
120 Driving and operating 9 Warning Do not let this special safety feature tempt you into taking risks when driving. Adapt speed to the road conditions. Control indicator v 3 80. Deactivation Press the v button. Control indicator v illuminates in the instrument cluster. TC is reactivated by pressing the v button again. Control indicator v extinguishes in the instrument cluster. TC is also reactivated the next time the ignition is switched on.
Driving and operating Deactivation When vehicle speed reaches 30 mph the ESP®Plus function will be restored automatically. Fault If the system detects a fault, control indicator A illuminates in the instrument cluster and the message CHECK ESP appears in the Driver Information Centre. Have the cause of the fault remedied by a workshop. Vehicle messages 3 83. When spinning of the drive wheels is required ESP®Plus can be deactivated: Press the v button.
122 Driving and operating Do not use the cruise control if it is not advisable to maintain a constant speed. With manual transmission automated, only activate cruise control in automatic mode. Control indicators m and U 3 82. Cruise control is now in standby mode and a corresponding message appears in the Driver Information Centre. Activation Accelerate to the desired speed and press switch < or ]. The current speed is now stored and maintained and the accelerator pedal can be released.
Driving and operating Increase speed Automatic deactivation: ■ Vehicle speed drops below 20 mph, ■ The brake pedal is depressed, ■ The clutch pedal is depressed, ■ Selector lever in N. The speed is stored and a corresponding message appears in the Driver Information Centre. Reduce speed Press switch R at a speed above 20 mph. If the stored speed is much higher than the current speed, the vehicle will accelerate powerfully until the stored speed is obtained.
124 Driving and operating Where the limit speed cannot be maintained, e.g. when driving on a steep decline, the limit speed will flash in the Driver Information Centre. Increase limit speed The limit speed can be increased continuously or in small increments by holding down or tapping switch < repeatedly. Reduce limit speed The limit speed can be decreased continuously or in small increments by holding down or tapping switch ] repeatedly.
Driving and operating closer to the obstacle. When the distance is less than 1 ft, the buzzer is continuous. 9 Warning Under certain circumstances, various reflective surfaces on objects or clothing as well as external noise sources may cause the system to fail to detect obstacles. Special attention must be paid to low obstacles which can damage the lower part of the bumper. vans). Object identification in the upper part of these vehicles cannot be guaranteed.
126 Driving and operating Fault If the system detects an operating fault, a continuous acoustic alarm will sound for approx. 5 seconds when selecting reverse gear. Consult a workshop to have the cause of the fault remedied. Rear view camera The remaining buttons on the monitor enable the user to select source AV1 or AV2 and adjust the brightness and contrast of the display monitor. To achieve the optimum visibility, the rear view camera must not be obscured by dirt, snow or ice.
Driving and operating Fuel Fuel for diesel engines Only use diesel fuel that complies with EN 590. The fuel must have low sulphur content (max. 10 ppm). Equivalent standardised fuels with a biodiesel (= FAME according to EN14214) content of max. 7% by volume (like DIN 51628 or equivalent standards) may be used. In countries outside the European Union use Euro-Diesel fuel with a sulphur concentration below 50 ppm.
128 Driving and operating Fuel consumption - CO2Emissions For the values specific to your vehicle, refer to the EEC Certificate of Conformity provided with your vehicle or other national registration documents. General information Remove the fuel filler cap by turning it anti-clockwise. The fuel filler cap can be hung on the lower hook of the fuel filler flap. Caution Wipe off any overflowing fuel immediately. When refuelling is complete, replace the filler cap and turn it clockwise.
Driving and operating Trailer hitch General information Only use towing equipment that has been approved for your vehicle. Entrust fitting of towing equipment at a later date to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment. Driving characteristics and towing tips In the case of trailers with brakes, attach the breakaway stopping cable. Before attaching a trailer, lubricate the coupling ball.
130 Driving and operating in the case of heavy trailers. The vertical coupling load should never fall below 25 kg. In the case of trailer loads of 1200 kg or more, the vertical coupling load should not be less than 50 kg. Rear axle load When the trailer is coupled and the towing vehicle fully loaded (including all occupants), the permissible rear axle load (see identification plate or vehicle documents) must not be exceeded.
Driving and operating If the system does not operate, repeat the procedure or gradually release the clutch pedal. To deactivate, depress the clutch pedal and press switch on the instrument panel.
132 Vehicle care Vehicle care General Information ................... 132 Vehicle checks ........................... 133 Bulb replacement ....................... 140 Electrical system ........................ 148 Vehicle tools .............................. 150 Wheels and tyres ....................... 151 Jump starting ............................. 160 Towing ....................................... 162 Appearance care .......................
Vehicle care ■ ■ ■ ■ Fill up the washer fluid reservoir. Check the engine oil level. Check the coolant level. Fit the number plate, if necessary. End-of-life vehicle recovery Information on end-of-life vehicle recovery centres and the recycling of end-of-life vehicles is available on our website. Only entrust this work to an authorised recycling centre. Vehicle checks Bonnet Performing work Opening 133 9 Warning Only perform engine compartment checks when the ignition is off.
134 Vehicle care Closing Before closing the bonnet, press the support into the holder. Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged. Caution It is the owner's responsibility to maintain the proper level of an appropriate quality oil in the engine. Engine oil Pull the safety catch, located slightly left of centre, and open the bonnet. Check the engine oil level manually on a regular basis to prevent damage to the engine.
Vehicle care 135 thousand miles. Only then can the actual degree of consumption be established. If consumption exceeds more than 0.5 litres every 600 miles after this running-in period, consult a workshop. Capacities 3 188, Engine oil level monitor 3 74. Fit the cap on straight and tighten it. We recommend the use of the same type of engine oil that was used at the last change. The engine oil level must not exceed the maximum mark MAX on the dipstick.
136 Vehicle care concentration checked and have the cause of the coolant loss remedied by a workshop. If a substantial amount of coolant is required, it will be necessary to bleed any trapped air from the cooling system. Seek the assistance of a workshop. Washer fluid A squealing noise, or illumination of brake pad wear control indicator F indicates that the brake lining is at its minimum thickness. Continued driving is possible but have the brake linings replaced as soon as possible.
Vehicle care 137 Battery access The brake fluid level must be between the MIN and MAX marks. When topping up, ensure maximum cleanliness as contamination of the brake fluid can lead to brake system malfunctions. Have the cause of the loss of brake fluid remedied by a workshop. Only use brake fluid approved for your vehicle. Brake and clutch fluid 3 168. Vehicle battery The vehicle battery is maintenancefree. Batteries do not belong in household waste.
138 Vehicle care Warning label ■ See the Owner's Manual for further information. ■ Explosive gas may be present in the vicinity of the battery. Diesel fuel filter Battery maintenance 9 Danger Meaning of symbols: ■ No sparks, naked flames or smoking. ■ Always shield eyes. Explosive gases can cause blindness or injury. ■ Keep the battery out of reach of children. ■ The battery contains sulfuric acid which could cause blindness or serious burn injuries.
Vehicle care Diesel fuel system bleeding 3. Manually operate the in-line supply pump slowly and steadily until fuel discharging from the loosened vent screw is free of air bubbles. 4. Retighten the vent screw. If the engine cannot be started after several attempts to bleed the diesel fuel system, seek the assistance of a workshop. Wiper blade replacement Wiper blades on the windscreen If the fuel tank has been run dry, it will be necessary to air vent or bleed the diesel fuel system.
140 Vehicle care Bulb replacement Headlights High beam Switch off the ignition and turn off the relevant switch or close the doors. Only hold a new bulb at the base. Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. Bulb check After a bulb replacement, switch on the ignition, operate and check the lights. Headlights have separate systems for high beam 1 and low beam 2. 1. Remove headlamp protective cover. 2. Detach wiring connector from bulb.
Vehicle care 141 Low beam 3. Release spring clip. 4. Withdraw bulb from reflector housing. 5. Renew bulb and secure with spring clip. 6. Reattach wiring connector to bulb. 7. Replace headlamp protective cover. 1. Remove headlamp protective cover. 2. Detach wiring connector from bulb. 3. Rotate bulb holder anti-clockwise to disengage. 4. Withdraw bulb holder from reflector housing. 5. Detach bulb from bulb holder and renew the bulb. 6.
142 Vehicle care Adaptive forward lighting Sidelights Cornering light 1. Remove protective cover. 2. Detach wiring connector from bulb. 3. Rotate bulb holder anti-clockwise to disengage. 4. Withdraw bulb holder from reflector housing. 5. Detach bulb from bulb holder and renew the bulb. 6. Insert the bulb holder, engaging the two lugs in the reflector housing and rotate clockwise to secure. 7. Reattach wiring connector to bulb. 8. Replace protective cover.
Vehicle care 143 Front turn signal lights 5. Detach bulb from bulb holder and renew the bulb. 6. Insert the bulb holder, engaging the two lugs in the reflector housing and rotate clockwise to secure. 7. Reattach wiring connector to bulb. 8. Replace protective cover. Fog lights Have bulbs replaced by a workshop. 1. Remove protective cover. 2. Detach wiring connector from bulb. 3. Rotate bulb holder anti-clockwise to disengage. 4. Withdraw bulb holder from reflector housing. 5.
144 Vehicle care Tail lights Rear brake, tail, turn signal, reverse and fog tail lights 5. Remove the three screws from the rear of the lamp assembly. 6. Remove bulb holder from the lamp assembly. 1. Remove the upper and lower trim panels from the rear pillar. 2. Unscrew the two nuts from the locating pins on the rear of the lamp assembly. 3. Withdraw the lamp assembly rearwards from the outer side. 4. Detach wiring connector from lamp assembly. 7.
Vehicle care Side turn signal lights 1. Push the lamp assembly to the right and pull at the left-hand side of the lamp assembly to release from the aperture. 5. Reattach wiring connector. 6. Install lamp assembly into aperture and push to the left to secure. Mirror turn signal lights 145 5. Replace bulb holder. 6. Replace the screw. Centre high-mounted brake light 1. Move the lower mirror assembly from the front to access the screw. 2. Remove the screw using a torx screwdriver. 2.
146 Vehicle care 8. Replace the nut onto the locating pin on the rear of the lamp assembly. 9. Install cover on the inside of the rear door. Interior lights Front courtesy light Number plate light 3. Remove the lamp assembly from the aperture on the outer side. 4. Detach wiring connector from lamp assembly. 5. Remove bulb holder from lamp assembly and renew bulb. 6. Install bulb holder in lamp assembly and reattach wiring connector to lamp assembly. 7.
Vehicle care Load compartment light Front door panel light 147 Instrument panel illumination Have bulbs replaced by a workshop. 1. Remove lamp assembly using a flat blade screwdriver. 2. Detach wiring connector from lamp assembly. 3. Remove lens cover and renew bulb. 4. Reattach wiring connector and reinstall lamp assembly. 1. Remove lamp assembly using a flat blade screwdriver. 2. Remove lens on lamp assembly. 3. Renew bulb and install lens. 4. Reinstall lamp assembly.
148 Vehicle care Electrical system Fuse extractor Fuses Data on the replacement fuse must match the data on the defective fuse. There are two fuse boxes in the vehicle: ■ on the left-hand side of the instrument panel, behind the trim panel. ■ in the engine compartment located below the coolant expansion tank. Before replacing a fuse, turn off the respective switch and the ignition. A blown fuse can be recognised by its melted wire. Do not replace the fuse until the cause of the fault has been remedied.
Vehicle care Due to restricted accessibility, have fuses replaced by a workshop. Symbol Circuit S Right side lights T Left side lights W Right low beam a Left low beam > Front fog light To help in replacing fuses, a fuse extractor is located in the instrument panel fuse box. Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse.
150 Vehicle care Symbol Circuit Symbol Circuit Infotainment system, seat heating, vehicle display screen, audio connections, alarm n Right heated rear window R Windscreen washer M Electronic immobiliser ? Power outlet U Heated seats Ì Cigarette lighter FBL Cornering light e Instrument panel l Hands-free connection U Central locking & Tachograph O Turn signals, rear fog lights, body control module PTO Power take-off DIAG Diagnostic connector j Horn u ABS, Electronic stabil
Vehicle care To access this unit, slide the seat fully forwards and fold down the backrest. Tyre repair kit 3 154. Spare wheel 3 159. Vehicles with Rear-wheel drive: A hydraulic jack and a set of extension pieces for use with the jack are also included. 151 Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage.
152 Vehicle care In accordance with country-specific regulations, a notice indicating the maximum permissible speed for the tyres must be affixed within the driver's field of vision. Tyre designations E.g. 215/65 R 16 C 109 R 215 = Tyre width, mm 65 = Cross-section ratio (tyre height to tyre width), % R = Belt type: Radial RF = Type: RunFlat 16 = Wheel diameter, inches C = Cargo or commercial use 88 = Load index e.g. 109 is equivalent to approx.
Vehicle care Changing tyre and wheel size If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogramme the speedometer as well as the nominal tyre pressure and make other vehicle modifications. 153 9 Warning Use of unsuitable tyres or wheel covers could lead to sudden pressure loss and thereby accidents. Tyre chains 9 Warning The legally permissible minimum tread depth (1.
154 Vehicle care Always use fine mesh chains that add no more than 15 mm to the tyre tread and the inboard sides (including chain lock). Tyre damage exceeding 4 mm or that is at the tyre's sidewall near the rim cannot be repaired with the tyre repair kit. 9 Warning 9 Warning Damage may lead to tyre blowout. Wheel covers on steel wheels may come into contact with parts of the chains. In such cases, remove the wheel covers.
Vehicle care 7. Screw the sealant filler hose to the tyre valve. 8. The rocker switch on the compressor must be set to position O. 9. Connect the red < power supply lead on the compressor to the jump start terminal 3 160. 10. Connect the black ] power supply lead to a vehicle grounding point, e.g. the engine block or an engine mounting bolt. To avoid discharging the battery, we recommend running the engine. 155 11. Set the rocker switch on the compressor to position I. The tyre is filled with sealant.
156 Vehicle care 14. The prescribed tyre pressure should be obtained within 10 minutes. Tyre pressure 3 189. When the correct pressure is obtained, turn off the compressor by setting rocker switch to position O. If the prescribed tyre pressure is not obtained within 10 minutes, remove the tyre repair kit. Move the vehicle one tyre rotation (approx. 2 metres). Reattach the tyre repair kit and continue the filling procedure for 10 minutes.
Vehicle care not be driven. Seek the assistance of a workshop. 20. Stow tyre repair kit under the front seat. Note The driving characteristics of the repaired tyre are severely affected, therefore have this tyre replaced. If unusual noise is heard or the compressor becomes hot, turn compressor off for at least 30 minutes. The built-in safety valve opens at a pressure of 7 bar (102 psi). Note the expiry date of the kit. After this date its sealing capability is no longer guaranteed.
158 Vehicle care jacking hole located nearest the wheel concerned. Ensure the jack is positioned correctly. The jack base must be on the ground directly below the jacking hole in a manner that prevents it from slipping. Attach wheel wrench onto the jack and raise the vehicle by turning the wrench until the wheel is clear of the ground. 4. 3.
Vehicle care twin rear wheels), 264 Nm (Rearwheel drive with single rear wheels). 9. Refit wheel cover. 10. Stow the replaced wheel 3 159 and the vehicle tools 3 150. 11. Have the new wheel balanced on the vehicle. Check the tyre pressure of the installed tyre 3 189 and also the wheel bolt/nut torque as soon as possible. Have the defective tyre renewed or repaired. could affect driveability. Have the defective tyre replaced as soon as possible.
160 Vehicle care Twin rear wheel vehicles have an additional mounting plate attached to the spare wheel. Before using the wheel, undo the nut and remove the mounting plate. downwards. Tighten cable using the wheel wrench and adapter until the wheel is secured. Summer and winter tyres If you use winter tyres, the spare wheel may still be fitted with a summer tyre.
Vehicle care Caution The air suspension system must be switched off prior to jump starting. 9 Warning Avoid contact of the battery with eyes, skin, fabrics and painted surfaces. The fluid contains sulphuric acid which can cause injuries and damage in the event of direct contact. ■ Never expose the vehicle battery to naked flames or sparks. ■ A discharged vehicle battery can already freeze at a temperature of 0 °C. Defrost the frozen vehicle battery before connecting jump leads.
162 Vehicle care Jump starting procedure Lead connection order: 1. Connect the red lead to the positive terminal of the booster battery. 2. Connect the other end of the red lead to the jump start terminal of the vehicle with the discharged vehicle battery. 3. Connect the black lead to the negative terminal of the booster battery. 4. Connect the other end of the black lead to a vehicle grounding point, such as the engine block or an engine mounting bolt.
Vehicle care Caution Do not tow the vehicle from the rear. The front towing eye must only be used for towing and not recovering a vehicle. Switch on ignition to release steering wheel lock and to permit operation of brake lights, horn and windscreen wipers. Switch off the air suspension system 3 110. Transmission in neutral. If neutral cannot be selected on vehicles with MTA transmission, the vehicle must only be towed with the drive wheels raised off the ground.
164 Vehicle care Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only when absolutely necessary, as this has a degreasing effect and impairs lock function. After using a de-icing agent, have the locks regreased by a workshop. Washing The paintwork of your vehicle is exposed to environmental influences. Wash and wax your vehicle regularly.
Vehicle care Windows and windscreen wiper blades Use a soft lint-free cloth or chamois leather together with window cleaner and insect remover. When cleaning the rear window from inside, always wipe in parallel to the heating element to prevent damage. For mechanical removal of ice, use a sharp-edged ice scraper. Press the scraper firmly against the glass so that no dirt can get under it and scratch the glass. Clean smearing wiper blades with a soft cloth and window cleaner.
166 Vehicle care Caution Close Velcro fasteners as open Velcro fasteners on clothing could damage seat upholstery. The same applies to clothing with sharp-edged objects, like zips or belts or studded jeans. Plastic and rubber parts Plastic and rubber parts can be cleaned with the same cleaner as used to clean the body. Use interior cleaner if necessary. Do not use any other agent. Avoid solvents and petrol in particular. Do not use highpressure jet cleaners.
Service and maintenance Service and maintenance General information ................... 167 Recommended fluids, lubricants and parts .................................... 168 General information Service information In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified. The detailed, up-to-date service schedule for the vehicle is available at the workshop.
168 Service and maintenance The service display, located in the Driver Information Centre, indicates when the next service is due. Seek the assistance of a workshop. Service display 3 75. Engine oil lever monitor 3 74. Recommended fluids, lubricants and parts Recommended fluids and lubricants Only use products that meet the recommended specifications. Damage resulting from the use of products not in line with these specifications will not be covered by the warranty.
Service and maintenance Additional engine oil additives The use of additional engine oil additives could cause damage and invalidate the warranty. Engine oil viscosity grades The SAE viscosity grade gives information of the thickness of the oil. Multigrade oil is indicated by two figures, e.g. SAE 5W-30. The first figure, followed by a W, indicates the low temperature viscosity and the second figure the high temperature viscosity.
170 Technical data Technical data Vehicle identification .................. 170 Vehicle data ............................... 173 Vehicle identification Vehicle Identification Number The VIN is also displayed behind a removable plastic cover on the front right hand door step. Unclip the covers using a flat blade screwdriver to access. The Vehicle Identification Number (VIN) is visible through the windscreen.
Technical data Identification plate The identification plate is located on the right hand door pillar.
172 Technical data Engine identification The technical data tables show the engine identifier code. Engine data 3 174. To identify the respective engine, refer to the engine power in the EEC Certificate of Conformity provided with your vehicle or other national registration documents.
Technical data 173 Vehicle data Recommended fluids and lubricants Required engine oil quality Engine oil quality dexos 2 ✔ In case dexos quality is unavailable you may use max. 1 litre engine oil quality ACEA C3 once between each oil change.
174 Technical data Engine data Sales designation 2.3 CDTI2) 2.3 CDTI2) 2.3 CDTI2) Engine identifier code M9T M9T M9T Number of cylinders 4 4 4 Piston displacement [cm3] 2299 2299 2299 Engine power [kW] (brake horse power) 74 (100) 92 (125) 107 (146) at rpm 3500 3500 3500 Torque [Nm] 285 310 350 at rpm 1250 - 2000 1250 - 2500 1500 - 2750 Fuel type Diesel Diesel Diesel 2) With or without diesel particle filter.
Technical data 175 Vehicle weight Kerb weight, basic model Model Drive wheels Length Roof height Gross vehicle weight Kerb weight3)4) Van Front-wheel drive L1 H1 2800 1806 3300 1811 3500 1816 2800 1834 3300 1839 3500 1844 3300 1885 3500 1890 3300 1921 3500 1931 H2 3500 1970 H3 3500 2010 H2 L2 H2 H3 L3 3) Kerb weight and gross vehicle weight increase on models fitted with bad road equipment package - refer to identification plate.
176 Technical data Model Drive wheels Length Roof height Gross vehicle weight Kerb weight3)4) Van Rear-wheel drive L3 H2 35005) 2110 35006) 2246 4500 2246 35005) 2148 35006) 2279 4500 2279 35006) 2324 4500 2324 35006) 2366 4500 2366 H3 L4 H2 H3 4) 3) 5) 6) Minimum vehicle weight according to type approval, including all fluids, vehicle tools and a 90% fuel load. Excludes the weight of the driver and deletable options, e.g. spare wheel, bulkhead and sliding side door.
Technical data Model Drive wheels Length Roof height Gross vehicle weight Kerb weight3)4) Platform Cab Front-wheel drive L1 H1 3500 1570 L2 H1 3500 1578 H2 3500 1593 H1 3500 1599 H2 3500 1613 L3 Model Drive wheels Length Roof height Gross vehicle weight Kerb weight3)4) Chassis Cab Front-wheel drive L2 H1 3500 1686 L3 H1 3500 1707 3) 4) 177 Kerb weight and gross vehicle weight increase on models fitted with bad road equipment package - refer to identification plate
178 Technical data Model Drive wheels Length Roof height Gross vehicle weight Kerb weight3)4) Chassis Cab Rear-wheel drive L2 H1 35005) 1835 L3 H1 35005) 1860 35006) 1975 45006) 1975 35006) 2005 45006) 2005 L4 H1 Model Drive wheels Length Roof height Gross vehicle weight Kerb weight3)4) Crew Cab Front-wheel drive L2 H1 3500 1887 L3 H1 3500 1915 3) 4) 5) 6) Kerb weight and gross vehicle weight increase on models fitted with bad road equipment package - refer to i
Technical data Model Drive wheels Length Roof height Gross vehicle weight Kerb weight3)4) Crew Cab Rear-wheel drive L2 H1 35005) 2037 L3 H1 35005) 2068 35006) 2154 45006) 2154 35006) 2223 45006) 2223 L4 H1 Model Drive wheels Length Roof height Gross vehicle weight Kerb weight3)4) Bus Front-wheel drive L3 H2 3900 2493 3) 4) 5) 6) 179 Kerb weight and gross vehicle weight increase on models fitted with bad road equipment package - refer to identification plate.
180 Technical data Vehicle dimensions Van, Doublecab Front-wheel drive Gross vehicle weight 2800, 3300, 3500 3300, 3500 3500 Size L1 L2 L3 Length [mm] 5048 5548 6198 Width without mirrors [mm] 2070 2070 2070 Width with mirrors [mm] 2470 2470 2470 Height - unladen (without antenna) [mm] H1 2303 - - H2 2496/25007) 2496/24997) 2488 H3 - 2745/27497) 2744 Wheelbase [mm] 3182 3682 4332 Track width [mm] Front 1750 1750 1750 Rear 1730 1730 1730 7) 3500 GVW.
Technical data Van, Doublecab Rear-wheel drive Gross vehicle weight 3500, 4500 3500, 4500 3500, 4500 Size L3 L3 L4 Length [mm] 6198 6198 6848 Width without mirrors [mm] 2070 2070 2070 Width with mirrors [mm] 2470 2470 2470 Height - unladen (without antenna) [mm] H2 25278)/25499) 2549 2557 H3 27868)/28159) 2815 2808 Wheelbase [mm] 3682 3682 4332 Track width [mm] Front 1750 1750 1750 Rear 17308)/16129) 1612 1612 8) 9) With Single rear wheels. With Twin rear wheels.
182 Technical data Combi Front-wheel drive Gross vehicle weight 2800, 3500 2800, 3500 Size L1 L2 Length [mm] 5048 5548 Width without exterior mirrors [mm] 2020 2020 Width with mirrors [mm] 2470 2470 Height - unladen (without antenna) [mm] H1 2303 - H2 - 2502 Wheelbase [mm] 3182 3682 Track width [mm] Front 1750 1750 Rear 1730 1730
Technical data Chassis Cab 183 Front-wheel drive Rear-wheel drive Gross vehicle weight 3500 3500 350010) 350010) 350011), 4500 350011), 4500 350011), 4500 Size L2 L3 L2 L3 L2 L3 L4 Length [mm] 5643 6293 5643 6293 5819 6192 6842 Width without mirrors [mm] 2070 2070 2070 2070 2070 2070 2070 Width with mirrors [mm] 2470 2470 2470 2470 2470 2470 2470 Height - unladen (without antenna) [mm] H1 2265 2258 2284 2276 2400 2283 2273 Wheelbase [mm] 3682 4332 3682
184 Technical data Crew Cab Front-wheel drive Rear-wheel drive 350012) 350013), 4500 350013), 4500 Gross vehicle weight 3500 3500 350012) Size L2 L3 L2 L3 L3 L4 Length [mm] 5643 6293 5643 6293 6192 6842 Width without mirrors [mm] 2070 2070 2070 2070 2070 2070 Width with mirrors [mm] 2470 2470 2470 2470 2470 2470 Height - unladen (without antenna) [mm] H1 2272 2263 2295 2285 2283 2273 Wheelbase [mm] 3682 4332 3682 4332 3682 4332 Track width [mm] Front 175
Technical data Platform Cab Front-wheel drive Gross vehicle weight 3500 3500 Size L2 L3 Length [mm] 5530 6180 Width without mirrors [mm] 2070 2070 Width with mirrors [mm] 2470 2470 Height - unladen (without antenna) [mm] H1 2270 2264 H2 2463 2457 Wheelbase [mm] 3682 4332 Track width [mm] Front 1750 1750 Rear 1730 1730 185
186 Technical data Bus Front-wheel drive Rear-wheel drive Gross vehicle weight 3900 4500 Size L3 L4 Length [mm] 6198 6848 Width without mirrors [mm] 2070 2070 Width with mirrors [mm] 2470 2470 Wheelbase [mm] 4332 4332 Height - unladen (without antenna) [mm] H2 2488 - H3 - 2808 Track width [mm] Front 1750 1750 Rear 1730 1612
Technical data Loadspace dimensions Van Front-wheel drive Length L2 Roof height H2 H3 H2 H3 Gross vehicle weight 3300, 3500 3500 3500 3500 Maximum rear door aperture height [mm] 1820 1820 1820 1820 Rear door aperture width (at floor) [mm] 1580 1580 1580 1580 Maximum load area height [mm] 1894 2144 1894 2144 Maximum load area width [mm] 1765 1765 1765 1765 Width between wheel arches [mm] 1380 1380 1380 1380 Maximum load floor length [mm] 3083 3083 3733 3733 L3 187
188 Technical data Van Rear-wheel drive Length L3 Roof height H2 Gross vehicle weight 3500 4500 3500 Maximum rear door aperture height [mm] 1724 1724 Rear door aperture width (at floor) [mm] 1580 Maximum load area height [mm] L4 H3 H2 H3 4500 4500 4500 1724 1724 1724 1724 1580 1580 1580 1580 1580 1798 1798 2048 2048 1798 2048 Maximum load area width [mm] 1765 1765 1765 1765 1765 1765 Width between wheel arches [mm] 1380 1080 1380 1080 1080 1080 Maximum lo
Technical data Tyre pressures Front-wheel drive Tyre pressure with full load14) Engine Gross Vehicle Weight Tyre Front [kPa/bar] (psi) Rear [kPa/bar] (psi) M9T 2800 215/65 R16 C 340/3.4 (49) 360/3.6 (52) 3300 215/65 R16 C 360/3.6 (52) 430/4.3 (62) 3500 225/65 R16 C 380/3.8 (55) 460/4.6 (68) Rear-wheel drive, with single rear wheels Tyre pressure with full load14) Engine Gross Vehicle Weight Tyre Front [kPa/bar] (psi) Rear [kPa/bar] (psi) M9T 3500 235/65 R16 C 360/3.
190 Customer information Customer information Customer information Customer information ................ 190 Vehicle data recording and pri‐ vacy ........................................... 190 This vehicle has systems that transmit and/or receive radio waves subject to Directive 1999/5/EC. These systems are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Copies of the original Declarations of Conformity can be obtained on our website.
Customer information ■ Vehicle reactions in particular driving situations (e.g. inflation of an airbag, activation of the stability regulation system) ■ Environmental conditions (e.g. temperature) These data are exclusively technical and help identifying and correcting errors as well as optimizing vehicle functions. Motion profiles indicating travelled routes cannot be created with these data. If services are used (e.g.
192 Index A Accessories and vehicle modifications .......................... 132 Adaptive forward lighting ..... 89, 142 Adjustable air vents ................... 103 Airbag and belt tensioners ........... 78 Airbag deactivation ................ 50, 78 Airbag label................................... 45 Airbag system .............................. 45 Air conditioning regular operation ................................ 105 Air conditioning system ................ 95 Air intake ...............................
193 Climate control systems............... 94 Clock ............................................ 71 Control indicators.......................... 76 Control of the vehicle ................. 106 Controls........................................ 68 Convex shape .............................. 30 Coolant....................................... 135 Coolant and antifreeze............... 168 Coolant heater............................ 100 Cornering light...................... 89, 142 Coupling ball bar.................
194 H Hand brake - see Parking brake. 119 Hazard warning flashers .............. 89 Headlight flash ............................. 88 Headlight range adjustment ........ 88 Headlights...................... 87, 88, 140 Headlights when driving abroad . . 88 Head restraint adjustment ............. 8 Head restraints ............................ 35 Heated mirrors ............................. 31 Heated rear window ..................... 34 Heating ........................................
195 Pollen filter ................................. 104 Power door locks.......................... 22 Power outlets ............................... 71 Power side step............................ 24 Power sliding door........................ 24 Power steering fluid.................... 136 Power take-off............................ 130 Power windows ............................ 32 Preheating ................................... 81 Puncture.............................
196 Tread depth ............................... 152 Trip computer .............................. 85 Triple-Info-Display ....................... 83 Trip odometer .............................. 73 Turn and lane-change signals ..... 89 Turn signal ................................... 78 Tyre chains ................................ 153 Tyre changing............................. 157 Tyre designations ...................... 152 Tyre pressure ............................ 152 Tyre pressures .........................
