Owner’s Manual Model Year 2012 Edition: November 2011 TS 1714-B-12 0-1 VAUXHALL Combo Owner’s Manual Model Year 2012 Edition: November 2011 TS 1714-B-12
Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 18 Seats, restraints ........................... 29 Storage ........................................ 44 Instruments and controls ............. 50 Lighting ........................................ 68 Climate control ............................. 73 Driving and operating ................... 78 Vehicle care .................................
2 Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". Thank you for choosing a Vauxhall. We wish you many hours of pleasurable driving.
Introduction 5
6 In brief In brief Vehicle unlocking Unlocking with key Unlocking with radio remote control Initial drive information Turn the key in the driver's door lock to the front. Press button Ä to unlock the doors and load compartment. Open the doors by pulling the handles, to open the tailgate, press the button under the handle. Press button Å; only the load compartment is unlocked. Radio remote control 3 19, Central locking system 3 20, Load compartment 3 23.
In brief Seat adjustment Seat backrests Seat height Turn handwheel. Do not lean on seat when adjusting. Seat position 3 30, Seat adjustment 3 31. Lever pumping motion up = higher down = lower 7 Seat positioning Pull handle, slide seat, release handle. Seat position 3 30, Seat adjustment 3 31. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. Operate lever and adjust body weight on seat to raise or lower it. Seat position 3 30, Seat adjustment 3 31.
8 In brief Head restraint adjustment Seat belt Mirror adjustment Interior mirror Press release catch, adjust height, engage. Head restraints 3 29. Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle. Seat position 3 30, Seat belts 3 32, Airbag system 3 35. Adjust the lever on the underside to reduce dazzle.
In brief Steering wheel adjustment Exterior mirrors Swivel lever in required direction. 9 Select the relevant exterior mirror by turning the control to left _ or right 6. Then swivel the control to adjust the mirror. In position o no mirror is selected. Convex exterior mirrors 3 25, Electric adjustment 3 25, Folding exterior mirrors 3 25, Heated exterior mirrors 3 26. Unlock the lever, adjust the steering wheel, then engage lever and ensure it is fully locked.
10 In brief Instrument panel overview
In brief 1 2 3 Fixed air vents ....................... 77 Side air vents ........................ 76 Light switch .......................... 68 4 Turn and lane-change signals, headlight flash, low beam and high beam ..... 70 Instruments .......................... 55 5 Driver Information Centre ...... 64 Windscreen wiper, windscreen washer system, rear wiper ................ 51 6 7 Trip reset ............................... 55 Centre air vents .................... 76 Headlight range adjustment .......
12 In brief Fog lights Press light switch > = front fog lights r = rear fog light Headlight flash, high beam and low beam headlight flash = pull lever high beam = push lever low beam = pull lever High beam 3 68, Headlight flash 3 68. Turn and lane-change signals lever up = right turn signal lever down = left turn signal Turn and lane-change signals 3 70.
In brief Hazard warning flashers Horn Washer and wiper systems Windscreen wiper Operated with the ¨ button. Hazard warning flashers 3 69. 13 Press j. Twist lever: É = fast È = slow Ç = intermittent wiping = off § For a single wipe when the windscreen wiper is off, move the lever up. Windscreen wiper 3 51, Wiper blade replacement 3 104.
14 In brief Windscreen and headlight washer systems Rear window wiper and washer systems Pull lever: Windscreen and headlight washer system 3 51, Washer fluid 3 102. Twist to activate the rear window wiper. The rear screen wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged. Rear window wiper/washer 3 52. Push lever. Washer fluid is sprayed on the rear window and the wiper wipes a few times.
In brief Demisting and defrosting the windows Set the temperature control to V. Set fan to 4. Set air distribution control to V. Cooling n on. Heated rear window Ü on. Climate control system 3 73. Transmission 15 Manual transmission automated Manual transmission Reverse: with the vehicle stationary, depress the clutch pedal, press the release button on the selector lever and engage the gear.
16 In brief Starting off Starting the engine Stop-start system ■ Turn key to position MAR ■ move the steering wheel slightly to release the steering wheel lock ■ operate clutch and brake ■ do not operate accelerator pedal ■ diesel engines: turn the key to position MAR for preheating and wait until control indicator ! goes out ■ turn key to position AVV and release Starting the engine 3 79.
In brief Parking ■ Always apply the parking brake. Activate the manual parking brake without pressing the release button. Apply as firmly as possible on a downhill slope or uphill slope. Depress foot brake at the same time to reduce operating force. ■ Switch off the engine. Turn the ignition key to position STOP and remove it. Turn the steering wheel until the steering wheel lock is felt to engage. ■ If the vehicle is on a level surface or uphill slope, engage first gear.
18 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 18 Doors ........................................... 21 Vehicle security ............................ 24 Exterior mirrors ............................ 25 Interior mirrors ............................. 26 Windows ...................................... 26 Keys, locks Key with foldaway key section Keys Replacement keys The key number is specified in the Car Pass or on a detachable tag.
Keys, doors and windows Radio remote control Used to operate: ■ Central locking system ■ Anti-theft locking system The radio remote control has an approximate range of up to 5 metres. It can be restricted by external influences. The hazard warning flashers confirm operation. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation.
20 Keys, doors and windows replace the battery (type CR 2032), paying attention to the installation position. Refit the battery holder in the key and secure the screw. Press button Å: The load compartment (rear doors / tailgate and sliding side doors) are unlocked. Locking Close all doors. If the doors are not closed properly, the central locking system will not work. Central locking system Unlocks and locks doors and load compartment.
Keys, doors and windows Unlocking the load compartment from inside the vehicle Child locks 21 Doors Sliding door 9 Warning Press button Å: The load compartment (rear doors / tailgate and sliding side doors) are unlocked. When the load compartment is locked the LED in the button is illuminated. Use the child locks whenever children are occupying the rear seats. Using a key, turn button on sliding door lock to the horizontal position. The door cannot be opened from inside.
22 Keys, doors and windows Rear doors To open the left hand rear door pull the outside handle. The door is opened from inside the vehicle by pressing down the interior handle. Make other road users aware of the vehicle, by using a warning triangle or other equipment specified in the road traffic regulations. The right hand rear door is released using the lever. 9 Warning The rear lights may be obscured if the rear doors are open and the vehicle is parked on the roadside.
Keys, doors and windows 9 Warning Ensure extended opening doors are secured when fully opened. Opened doors may slam closed due to the force of the wind! Always close the right hand door before the left hand door. Load compartment Tailgate Opening Press the button underneath the moulding. 23 Closing 9 Warning Do not drive with the tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases could enter the vehicle.
24 Keys, doors and windows Vehicle security Activating Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. The system deadlocks all the doors. All doors must be closed otherwise the system cannot be activated.
Keys, doors and windows Exterior mirrors 25 Electric adjustment Folding Select the relevant exterior mirror by turning the control to left _ or right 6. Then swivel the control to adjust the mirror. In position o no mirror is selected. For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing.
26 Keys, doors and windows Heated Interior mirrors Windows Manual anti-dazzle Manual windows The door windows can be opened or closed with the window winders. Power windows 9 Warning Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Adjust the lever on the underside to reduce dazzle. Take care when operating the power windows. Risk of injury, particularly to children.
Keys, doors and windows Safety function If the window glass encounters resistance during automatic closing, it is immediately stopped and opened again. Operate the switch for the respective window by pushing to open or pulling to close. Pushing or pulling briefly: window moves up or down in stages if the switch is held. Pushing or pulling firmly and then releasing: window moves up or down fully with safety function enabled. To stop movement, operate the switch once more in the same direction.
28 Keys, doors and windows Rear windows Heated rear window Opening rear windows To open, move lever outwards until the window is fully open. To close, pull lever then push until window is fully closed. Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Sun visors The sun visors can be folded down or swivelled to the side to prevent dazzling. A ticket holder is located on the backside of the sun visor.
Seats, restraints Seats, restraints Head restraints ............................ 29 Front seats ................................... 30 Seat belts ..................................... 32 Airbag system .............................. 35 Child restraints ............................. 38 Head restraints 29 Adjustment Head restraints on front seats Position 9 Warning Only drive with the head restraint set to the proper position. Height adjustment Press the button, adjust height and engage.
30 Seats, restraints Head restraints on rear seats Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. Height adjustment Pull the head restraint upwards or press the catch to release and push the head restraint downwards. Removal Press both catches, pull the head restraint upwards and remove. ■ Sit with buttocks as far back against the backrest as possible. Adjust the distance between the seat and the pedals so that legs are slightly angled when pressing the pedals.
Seats, restraints Seat adjustment 9 Danger Pull handle, slide seat, release handle. Seat height Seat backrests Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat positioning Turn handwheel. Do not lean on backrest when adjusting.
32 Seats, restraints Armrest Heating Raise or lower the armrest as required. Activate heating by pressing ß button for the seat with the ignition on. LED in button ß on: relevant front seat heating on. Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the sitting position. Therefore the risk of injury is considerably reduced. 9 Warning Fasten seat belt before each trip.
Seats, restraints Seat belts are designed to be used by only one person at a time. They are not suitable for people smaller than 150 cm. Child restraint system 3 38. Periodically check all parts of the belt system for damage, pollution and proper functionality. Have damaged components replaced. After an accident, have the belts and triggered belt pretensioners replaced by a workshop. Notice Make sure that the belts are not damaged by shoes or sharp-edged objects or are trapped.
34 Seats, restraints Height adjustment Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing. 1. Pull belt out slightly. 2. Press button down. 3. Adjust height and engage. Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving.
Seats, restraints Removing To release belt, press red button on belt buckle. Seat belts on the rear seats The seat belt for the rear centre seat can only be withdrawn from the retractor if the backrest is in the rear position. Using the seat belt while pregnant 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen. 35 Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment.
36 Seats, restraints Notice The airbag systems and belt pretensioner control electronics are located in the centre console area. Do not put any magnetic objects in this area. Do not fix any objects onto the airbag covers and do not cover them with other materials. Each airbag is triggered only once. Have deployed airbags replaced by a workshop. Furthermore, it might be necessary to have the steering wheel, the instrument panel, parts of the panelling, the door seals, handles and the seats replaced.
Seats, restraints Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system 37 The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and pelvis in the event of a side-on collision considerably. 9 Warning Keep the area in which the airbag inflates clear of obstructions. Notice Only use protective seat covers that have been approved for the vehicle. Be careful not to cover the airbags.
38 Seats, restraints Front passenger seat airbags are deactivated and will not inflate in the event of a collision. Control indicator * illuminates continuously in the instrument cluster. A child restraint system can be installed in accordance with the chart Child restraint installation locations 3 40. 9 Danger Risk of fatal injury for a child using a child restraint system on a seat with activated front passenger airbag.
Seats, restraints deactivated; if not, the triggering of the airbags poses a risk of fatal injury to the child. This is especially the case if rearfacing child restraint systems are used on the front passenger seat. Selecting the right system The rear seats are the most convenient location to fasten a child restraint system. Children should travel facing rearwards in the vehicle as long as possible.
40 Seats, restraints Child restraint installation locations Permissible options for fitting a child restraint system Front passenger seat Second row Third row Weight and age class activated airbag deactivated airbag outboard seat centre seat Group 0: up to 10 kg or approx. 10 months X U1 U, < U X Group 0+: up to 13 kg or approx. 2 years X U1 U, < U X Group I: 9 to 18 kg or approx. 8 months to 4 years X U1 U, < U X Group II: 15 to 25 kg or approx.
Seats, restraints 41 Permissible options for fitting an ISOFIX child restraint system On front passenger seat On outboard seats On centre seat in On the seats in in the second row the second row the third row Weight class Size class Fixture Group 0: up to 10 kg E ISO/R1 X IL X X Group 0+: up to 13 kg E ISO/R1 X IL X X D ISO/R2 X IL X X C ISO/R3 X IL1) X X D ISO/R2 X IL X X C ISO/R3 X IL1) X X B ISO/F2 X IUF X X B1 ISO/F2X X IUF X X A ISO/F3 IUF X X Group
42 Seats, restraints ISOFIX size class and seat device A – ISO/F3 B – ISO/F2 B1 – ISO/F2X C – ISO/R3 D – ISO/R2 E – ISO/R1 = = = = = = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. ISOFIX mounting brackets are indicated by a label on the backrest. Before fastening a child seat adjust the head restraint to use position 3 29. Top-tether fastening eyes In addition to the ISOFIX mounting, fasten the Top-Tether strap to the Top-Tether fastening eyes.
44 Storage Storage Storage compartments Document holder Instrument panel storage Storage compartments ................ 44 Load compartment ....................... 46 Roof rack system ......................... 48 Loading information ..................... 49 Storage compartments are located in the instrument panel. Pull the rear of the document holder upwards from the instrument panel and rest in tilted position.
Storage 45 Glovebox Overhead console Underseat storage The glovebox should be closed whilst driving. Store only lightweight items such as paperwork or maps in the overhead console. Pull the loop on the seat cushion to gain access to the storage area. Cupholders Cupholders are located in the centre console. The cupholders can also be used to hold the portable ashtray unit 3 55.
46 Storage Load compartment To fold up, lower seats to the floor until they engage audibly. Raise backrests and guide them into an upright position until they engage audibly. The backrests are properly engaged when both red marks on the release levers are no longer visible. Ensure that the seat belts are positioned correctly before returning the seats to the upright position. Folding down rear seat backrests The rear seat backrest is divided into two parts. Both parts can be folded down.
Storage 47 Closing Opening Removing Pull the cover towards the rear using the handle and engage it in the retainers at the sides. Remove load compartment cover from the retainers at the sides. Hold the cover and guide it until it is fully rolled up. Open the load compartment cover. Pull the release lever and lift cover from retainers. Installing Insert either side of the load compartment cover in the recess, pull the release lever. Insert the load compartment cover and engage.
48 Storage Lashing eyes Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. Follow the installation instructions and remove the roof rack when not in use. Mounting roof rack The lashing eyes are designed to secure items against slippage, e.g. using lashing straps or luggage net. To fasten a roof rack, insert the mounting bolts in the holes indicated in the illustration.
Storage Loading information ■ Heavy objects in the load compartment should be evenly distributed and placed as far forward as possible. If objects can be stacked, the heavier objects should be placed at the bottom. ■ Secure objects with lashing straps attached to lashing eyes 3 48. ■ Secure loose objects in load compartment to prevent sliding. ■ Do not allow the load to protrude above the upper edge of the backrests. ■ Do not place any objects on the load compartment cover or the instrument panel.
50 Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Controls ....................................... 50 Warning lights, gauges and indicators ..................................... 55 Information displays ..................... 64 Vehicle messages ........................ 65 Trip computer ............................... 66 Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked.
Instruments and controls Horn Windscreen wiper/washer Windscreen wiper 51 Adjustable wiper interval Wiper lever in position Ç. The windscreen wiper will automatically adapt to the speed of the vehicle. Windscreen washer Press j. Twist É È Ç § = = = = fast slow intermittent wiping off For a single wipe when the windscreen wiper is off, move the lever up. Do not use if the windscreen is frozen. Switch off in car washes.
52 Instruments and controls Rear window wiper/washer Outside temperature Values can be adjusted via the SET ESC, R and S buttons in the instrument panel. Set time in Driver Information Centre Twist to activate the rear window wiper. Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times. Do not use if the rear window is frozen. Switch off in car washes. The rear window wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged.
Instruments and controls Press SET ESC and minutes will flash in the display. Press R or S to adjust. To select 12h or 24h clock, select Mode; pressing SET ESC will make the display flash. Press R or S to adjust. Press SET ESC briefly to return to the submenu. Set date Press the SET ESC button. Scroll R or S until Set date is displayed. Press SET ESC, the year will flash in the display. Press R or S to adjust. Press SET ESC and month will flash in the display. Press R or S to adjust.
54 Instruments and controls Short wheelbase van Combi Do not damage the outlet by using unsuitable plugs. Cigarette lighter Long wheelbase van Do not exceed the maximum power consumption of 180 watts. With ignition off, the power outlets are deactivated. Additionally the power outlets are deactivated in the event of low battery voltage. Electrical accessories that are connected must comply with the electromagnetic compatibility requirements laid down in DIN VDE 40 839.
Instruments and controls Ashtrays Caution To be used only for ash and not for combustible rubbish. Warning lights, gauges and indicators 55 Odometer Speedometer Displays the recorded distance in miles. Indicates vehicle speed. The portable ashtray should be placed in the cupholders in the centre console. Trip odometer Displays the recorded distance since the last reset.
56 Instruments and controls To reset the trip odometer, press and hold the TRIP button for approx. 2 seconds while the relevant trip odometer is displayed. Tachometer Caution If the needle is in the red warning zone, the maximum permitted engine speed is exceeded. Engine at risk. Fuel gauge Because of the fuel remaining in the tank, the top-up quantity may be less than the specified tank capacity. The needle will point to E and control indicator $ will flash to indicate a fault in the system.
Instruments and controls Engine coolant temperature gauge Caution If engine coolant temperature is too high, stop vehicle, switch off engine. Danger to engine. Check coolant level. Control indicators Displays the coolant temperature. C = engine operating temperature not yet reached central = normal operating area temperature H = temperature too high If control indicator $ illuminates in conjunction with a message in the information display the coolant temperature is too high.
58 Instruments and controls Control indicators in the instrument cluster
Instruments and controls Generic warning 9 illuminates yellow. Depending on version control indicator 9 may illuminate independently or in conjunction with Æ, t or r. 9 also illuminates if the fuel cut-off switch is triggered. If 9 illuminates together with I; stop engine immediately and seek the assistance of a workshop. Simultaneously a message may be displayed in the Driver Information Centre. Turn signal 2 or 3 flashes green. Flashes A turn signal or the hazard warning flashers are activated.
60 Instruments and controls With the front passenger airbag deactivated: * permanently illuminates yellow. Airbag deactivation 3 37. 9 Danger Risk of fatal injury for a child using a child restraint system together with activated front passenger airbag. Risk of fatal injury for an adult person with deactivated front passenger airbag. Charging system p illuminates red. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts.
Instruments and controls Illuminates after the ignition is switched on if the parking brake is applied 3 88. Brake pad wear F illuminates yellow. The front brake pads are worn, seek the assistance of a workshop immediately. Antilock brake system (ABS) u illuminates yellow. Illuminates for a few seconds after the ignition is switched on. The system is ready for operation when the control indicator extinguishes.
62 Instruments and controls Flashes The system is actively engaged. Engine output may be reduced and the vehicle may be braked automatically to a small degree. Electronic Stability Program 3 90, Traction Control system (ASR) 3 89. Preheating ! illuminates yellow. Preheating is activated. Only activates when outside temperature is low. Diesel particle filter [ illuminates yellow. The diesel particle filter requires cleaning. Continue driving until [ extinguishes.
Instruments and controls Depending on model, I may flash in the following ways: ■ for one minute every two hours ■ for three minute cycles with I off for intervals of five seconds This will continue until the engine oil is changed. Seek the assistance of a workshop. Illuminates when the ignition is switched on and goes out shortly after the engine starts. Low engine oil level Immobiliser y illuminates red. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts.
64 Instruments and controls Door open \ illuminates red. A door or the tailgate is open.
Instruments and controls 65 Vehicle messages Warning chimes When starting the engine or whilst driving Press the SET ESC button to access the menu and/or go to the next screen or confirm your choice. Hold down the SET ESC button to return to the previous screen. Press the R button to scroll up the screen and the menu options or increase the displayed value. Press the S button to scroll down the screen and the menu options or decrease the displayed value. Only one warning chime will sound at a time.
66 Instruments and controls Trip computer The trip computer provides information on driving data, which is continually recorded and evaluated electronically. ■ Average speed ■ Travel time (driving time) Reset trip computer information To reset the trip computer, select one of its functions, then press the TRIP button for a few seconds. The trip computer will reset automatically when the maximum value of any of the parameters is exceeded.
Instruments and controls Distance travelled Trip odometer Average speed Interruption of power supply Displays the distance driven since the last reset. The measurement can be restarted at any time. The average speed since the last reset is displayed. The measurement can be restarted at any time. Travel time The time elapsed since the since the last reset is displayed. The measurement can be restarted at any time.
68 Lighting Lighting Exterior lighting High beam Light switch Exterior lighting ............................ 68 Interior lighting ............................. 71 Turn light switch: § = off / daytime running lights 9 = sidelights / headlights Control indicator 8 3 63. Tail lights Tail lights are illuminated together with headlights and sidelights. To switch from low to high beam, push lever. To switch to low beam, pull lever. Headlight flash To activate the headlight flash, pull lever.
Lighting Headlight range adjustment Manual headlight range adjustment To adapt headlight range to the vehicle load to prevent dazzling: Press À or Á buttons until the required setting is displayed in the Driver Information Centre.
70 Lighting Turn and lane-change signals Switch the indicator off manually by moving the lever to its original position. Rear fog lights Front fog lights Lever up = right turn signal Lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel moves back, the turn signal is automatically deactivated. For five flashes, e.g. when changing lanes, press the lever until resistance is felt and then release.
Lighting Misted light covers The inside of the light covers may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing. The mist disappears quickly by itself; to help, switch on the headlights. Interior lighting Interior lights 71 Front courtesy light with reading lights Depending on vehicle, during entry and exit of the vehicle, the front and rear courtesy lights automatically come on and then switch off after a delay.
72 Lighting Rear courtesy lights Centre switch position: automatic interior light. To operate manually when the doors are closed, press the lens on either side. Load compartment lighting Depending on vehicle, the lighting switches on when the rear doors / tailgate or sliding side door is opened.
Climate control Climate control Climate control systems ............... 73 Air vents ....................................... 76 Maintenance ................................ 77 Climate control systems Heating and ventilation system 73 Heating will not be fully effective until the engine has reached normal operating temperature. Fan speed Adjust the air flow by switching the fan to the desired speed.
74 Climate control ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J. Air conditioning system Cooling (AC) Maximum cooling Air recirculation system Electronic climate control system Operated with the AC button and functional only when the engine and fan are running. The air conditioning system cools and dehumidifies (dries) the air when outside temperature is a little above the freezing point.
Climate control Controls for: ■ Temperature ■ Air distribution and menu selection ■ Fan speed AUTO = Automatic mode = air recirculation 4 Ê = demisting and defrosting OFF = switch on/off Automatic mode Heated rear window Ü 3 28. The preselected temperature is automatically regulated. In the automatic mode the fan speed and air distribution automatically regulate the air flow. The system can be manually adapted by use of air distribution and air flow controls.
76 Climate control Air distribution Press R, S and 6 buttons. LED in buttons illuminate. Arrows shown in the display indicate the distribution settings. Cooling The air conditioning system cools and dehumidifies (dries) when outside temperature is above a specific level. Therefore condensation may form and drip from under the vehicle. If no cooling or drying is required press n again to switch the cooling system off, thus saving fuel.
Climate control Side air vents Maintenance Air intake 77 Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low. Service Slide knob to the left to open vent. Direct the flow of air by swivelling the vent. Slide knob to the right to close vent.
78 Driving and operating Driving and operating Driving hints ................................. 78 Starting and operating ................. 78 Engine exhaust ............................ 82 Manual transmission .................... 83 Manual transmission automated .................................... 84 Brakes .......................................... 87 Ride control systems ................... 89 Cruise control ............................... 91 Object detection systems ............. 92 Fuel .............
Driving and operating Ignition switch positions Starting the engine 79 Starting the vehicle at low temperatures The start of the engine without additional heaters is possible down to -25 °С for diesel engines and -30 °C for petrol engines. Required is an engine oil with the correct viscosity, the correct fuel, performed services and a sufficiently charged battery.
80 Driving and operating Stop-start system Deactivation The engine will be switched off while the ignition stays on. Deactivate the stop-start system manually by pressing the ^ button in the centre console. The deactivation is indicated by the LED in the button illuminating. An Autostop is indicated when ^ flashes in the driver information centre. The stop-start system helps to save fuel and to reduce the exhaust emissions.
Driving and operating ■ The stop-start system is not manually deactivated ■ the driver's door is closed or the driver's seat belt is fastened ■ the battery is sufficiently charged and in good condition ■ the engine is warmed up ■ the ambient temperature is not too low ■ the climate control system does not inhibit an Autostop ■ the self-cleaning function of the diesel particle filter is not active ■ the vehicle has moved since the last Autostop ■ the brake vacuum is sufficient ■ the windscreen wipers are ope
82 Driving and operating an uphill slope, turn the front wheels away from the kerb. If the vehicle is on a downhill slope, engage reverse gear. Turn the front wheels towards the kerb. ■ Lock the vehicle. Engine exhaust 9 Danger Engine exhaust gases contain poisonous carbon monoxide, which is colourless and odourless and could be fatal if inhaled. If exhaust gases enter the interior of the vehicle, open the windows. Have the cause of the fault rectified by a workshop.
Driving and operating Caution If the cleaning process is interrupted, there is a risk of provoking severe engine damage. Cleaning takes place quickest at high engine speeds and loads. The control indicator [ extinguishes as soon as the self-cleaning operation is complete. Catalytic converter The catalytic converter reduces the amount of harmful substances in the exhaust gases. Caution Fuel grades other than those listed on pages 3 93, 3 133 could damage the catalytic converter or electronic components.
84 Driving and operating Caution It is not advisable to drive with the hand resting on the selector lever. Manual transmission automated The manual transmission automated (MTA) permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control. Transmission display Starting the engine Depress the foot brake when starting the engine.
Driving and operating Always move the selector lever in the appropriate direction as far as it will go. Upon release, it automatically returns to the centre position. N = Neutral. A/ = Switch between automatic M and manual mode. The transmission display shows AUTO when in automatic mode. R = Reverse gear. Engage only when vehicle is stationary. The transmission display shows "R" when reverse gear is engaged. + = Shift to a higher gear. = Shift to a lower gear.
86 Driving and operating Engine braking Automatic mode When driving downhill, the manual transmission automated does not shift into higher gears until a fairly high engine speed has been reached. It shifts down in good time when braking. Manual mode To utilise the engine braking effect, select a lower gear in good time when driving downhill. Rocking the vehicle Rocking the vehicle is only permissible if the vehicle is stuck in sand, mud, snow or a hole.
Driving and operating Activation Press the E button on the selector lever housing. Control indicator E is shown in the transmission display to indicate activation. If engine speed is too high the transmission switches to a higher gear, even in manual mode. Without kickdown this automatic shift is not effected in manual mode. Deactivation Eco mode is switched off by: ■ pressing the E button again, ■ switching to manual mode.
88 Driving and operating ABS starts to regulate brake pressure as soon as a wheel shows a tendency to lock. The vehicle remains steerable, even during hard braking. ABS control is made apparent through a pulse in the brake pedal and the noise of the regulation process. For optimum braking, keep the brake pedal fully depressed throughout the braking process, despite the fact that the pedal is pulsating. Do not reduce the pressure on the pedal.
Driving and operating The brakes release automatically as soon as the vehicle begins to accelerate. Ride control systems Traction Control system The Anti-Slip Regulator (ASR) is a component of the Electronic Stability Control system. ASR improves driving stability when necessary, regardless of the type of road surface or tyre grip, by preventing the drive wheels from spinning. As soon as the drive wheels starts to spin, engine output is reduced and the wheel spinning the most is braked individually.
90 Driving and operating ASR is reactivated by pressing the ASR OFF button again. ASR is also reactivated the next time the ignition is switched on. Fault ASR will switch off automatically in the event of a fault. Control indicator x will illuminate in the instrument cluster in conjunction with a message in the driver information centre. Seek the assistance of a workshop. Control indicator x 3 61.
Driving and operating Cruise control The cruise control can store and maintain speeds above approx. 20 mph. Deviations from the stored speeds may occur when driving uphill or downhill. Switching on Reduce speed Activation Deactivation Increase speed Resume stored speed Turn end of lever ON, control indicator m illuminates in the instrument cluster in conjunction with a message in the driver information centre.
92 Driving and operating Object detection systems Parking assist Fault In the event of a fault in the system, r illuminates and a message is displayed in the driver information centre. Additionally, r illuminates and a vehicle message is displayed in the driver information centre if a malfunction of the system due to temporary conditions like snow covered sensors is detected.
Driving and operating Notice The parking assist system automatically detects factory-fitted towing equipment. It is deactivated when the connector is plugged in. The sensor may detect a nonexistent object (echo disturbance) caused by external acoustic or mechanical disturbances. Fuel 93 Caution Fuel for petrol engines Only use unleaded fuel that complies with EN 228. Equivalent standardised fuels with an ethanol content of max. 10 % by volume may be used.
94 Driving and operating Fuel for natural gas operation Use natural gas with a methane content of approx. 78 - 99 %. L-gas (low) has approx. 78 - 87 % and H-gas (high) has approx. 87 - 99 %. Biogas with the same methane content can also be used if it has been chemically prepared and desulphurised. Only use natural gas or biogas that complies with DIN 51624. Liquid gas or LPG must not be used. Fuel selector Pressing button Y in the centre console switches between petrol and natural gas operation.
Driving and operating Close the flap. 9 Danger Fuel filler cap Fuel is flammable and explosive. No smoking. No naked flames or sparks. If you can smell fuel in your vehicle, have the cause of this remedied immediately by a workshop. Caution In case of misfuelling, do not switch on ignition. Release the fuel filler flap by pulling the flap. Insert key into fuel filler cap and turn to the left. To remove fuel filler cap, rotate anticlockwise 95 Only use genuine fuel filler caps.
96 Driving and operating Towing General information Only use towing equipment that has been approved for your vehicle. Vehicles with natural gas engine may require special towing equipment. Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment. Fitting of towing equipment could cover the opening of the towing eye. If this is the case use the coupling ball bar for towing.
Driving and operating The maximum permissible vertical coupling load (75 kg) is specified on the towing equipment identification plate and in the vehicle documents. Always aim for the maximum load, especially in the case of heavy trailers. The vertical coupling load should never fall below 25 kg. Rear axle load The permissible axle loads (see identification plate or vehicle documents) must not be exceeded.
98 Vehicle care Vehicle care General Information ..................... 98 Vehicle checks ............................. 99 Bulb replacement ....................... 105 Electrical system ........................ 109 Vehicle tools .............................. 113 Wheels and tyres ....................... 114 Jump starting ............................. 122 Towing ....................................... 124 Appearance care .......................
Vehicle care ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.g. anti-theft locking system. Putting back into operation When the vehicle is to be put back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir. ■ Check the engine oil level.
100 Vehicle care Closing 9 Danger Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged. The ignition system use extremely high voltage. Do not touch. Engine oil Bonnet Opening Push the safety catch and open the bonnet. Check the engine oil level manually on a regular basis to prevent damage to the engine. Ensure that the correct specification of oil is used. Recommended fluids and lubricants 3 129. Check with the vehicle on a level surface.
Vehicle care 101 Engine coolant Insert dipstick to the stop on the handle and make half a turn. The coolant provides freeze protection down to approx. -28 °C. Caution Only use approved antifreeze. Coolant level Caution When the engine oil level has dropped to the MIN mark, top up engine oil. We recommend the use of the same grade of engine oil that was used at last change. The engine oil level must not exceed the MAX mark on the dipstick.
102 Vehicle care If the cooling system is cold, the coolant level should be between the MIN and MAX mark. Top up if the level is low. Power steering fluid Washer fluid If the fluid level in the reservoir falls below the MIN mark consult a workshop. Fill with clean water mixed with a suitable quantity of windscreen washer fluid which contains antifreeze. 9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly.
Vehicle care Brakes A squealing noise, or illumination of brake pad wear control indicator F indicates that the brake lining is at its minimum thickness. Continued driving is possible but have the brake linings replaced as soon as possible. Once new brake linings are installed, do not brake unnecessarily hard for the first few journeys. Brake pad wear indicator F 3 61. Brake fluid 9 Warning Brake fluid is poisonous and corrosive. Avoid contact with eyes, skin, fabrics and painted surfaces. 103 battery.
104 Vehicle care Replacing the battery Notice Any deviation from the instructions given in this paragraph may lead to a temporary deactivation of the stopstart system. Wiper blade replacement Wiper blade on rear swing door Lift the wiper arm until it stays in the raised position, press button to disengage the wiper blade and remove. Attach the wiper blade slightly angled to the wiper arm and push until it engages. Lower wiper arm carefully.
Vehicle care Wiper blade on tailgate Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. Replace headlight bulbs from within the engine compartment. Lift wiper arm, press retaining clips to detach wiper blade. Attach the wiper blade to the wiper arm and push until it engages. Lower wiper arm carefully.
106 Vehicle care 5. Attach connector to bulb. 6. Engage wire clip. 7. Install protective cover. High beam 1. Remove protective cover. 2. Detach connector from bulb. 3. Disengage wire clip and remove bulb from reflector. 4. Insert new bulb in reflector so that the bulb aligns with the reflector recess. 5. Engage wire clip, plug connector onto bulb. 6. Install protective cover. Daytime running light 1. Remove protective cover. Side light 1. Remove protective cover.
Vehicle care 107 Tail lights 2. Withdraw bulb holder from reflector by turning anticlockwise. 3. Push bulb into holder slightly, rotate anticlockwise, remove and renew bulb. 4. Insert bulb holder in reflector. 5. Rotate clockwise to engage. 6. Install protective cover. 1. Remove three retaining screws. 2. Remove light housing from vehicle. 3. Disengage connector plug from bulb holder. 4. Unscrew the four retaining screws using a screwdriver.
108 Vehicle care 9. Engage connector plug. 10. Insert light housing in body, ensuring proper positioning. Tighten three retaining screws. Number plate light Tailgate Side turn signal lights Have bulbs replaced by a workshop. Brake light (1) Turn signal light (2) Tail light (3) Tail light/fog light (4) 7. Install seal on bulb holder ensuring it is fitted correctly. Install bulb holder in light housing ensuring that it engages properly. Tighten four retaining screws using a screw driver. 8.
Vehicle care Rear Swing doors 109 Electrical system Fuses 2. Turn the bulb holder anticlockwise to remove from the bulb housing. Remove the bulb by pulling. 3. Replace the bulb. 4. Insert bulb holder in bulb housing and rotate clockwise 5. Install the bulb housing ensuring it engages correctly. 1. Insert screwdriver as indicated by the arrows, press to the left and release the bulb housing. 2. Press bulb slightly towards spring clip and remove. 3. Replace the bulb. 4.
110 Vehicle care Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse. Fuse extractor Use a fuse extractor to remove fuses.
Vehicle care Engine compartment fuse box 111 No. Circuit F09 Rear door switch F10 Horn F14 High beam F15 PTCI heater F19 Air conditioning system F20 Heated rear window F21 Fuel pump F30 Fog lights The fuse box is in the front left of the engine compartment. Disengage the cover, and lift it upwards to remove. F84 CNG system F85 Power outlets F86 Cigarette lighter, heated seats F87 Stop-start system F88 Mirror heating After having changed defective fuses refit the fuse box cover.
112 Vehicle care Instrument panel fuse box No. Circuit F12 Right low beam F13 Left low beam, headlight range adjustment F31 Fusebox relays, body control unit relays F32 Courtesy lights F36 Diagnostic connector, climate control system, Infotainment system The fuse box is located on the driver's side behind the cover in the instrument panel.
Vehicle care No. Circuit Vehicle tools F53 Instrument panel Tools F94 Power outlet load compartment F95 Cigarette lighter, power outlet 113 Combi Van F96 Cigarette lighter, power outlet F97 Heated front seat F98 Heated front seat The tools and the vehicle jacking equipment are in the load compartment. The tools and the vehicle jacking equipment are in the storage area behind the front seat.
114 Vehicle care Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage. Seek the assistance of a workshop in the event of damage or unusual wear. Winter tyres Winter tyres improve driving safety at temperatures below 7 °C and should therefore be fitted on all wheels.
Vehicle care Tyres should be replaced for safety reasons at a tread depth of 2-3 mm (4 mm for winter tyres). Tyres age, even if they are not used. We recommend tyre replacement every 6 years. Changing tyre and wheel size The legally permissible minimum tread depth (1.6 mm) has been reached when the tread has worn down as far as one of the tread wear indicators (TWI). Their position is indicated by markings on the sidewall.
116 Vehicle care Tyre chains Tyre repair kit Minor damage to the tyre tread can be repaired with the tyre repair kit. Do not remove foreign bodies from the tyres. Tyre damage exceeding 4 mm or that is at tyre's sidewall cannot be repaired with the tyre repair kit. 9 Warning Tyre chains are only permitted on the front wheels. Always use fine mesh chains that add no more than 10 mm to the tyre tread and the inboard sides (including chain lock). Do not exceed 30 mph when snow chains are fitted.
Vehicle care 11. 12. 13. 5. Screw the flexible filler hose onto the tyre valve. 6. The switch on the compressor must be set to J. 7. Connect the compressor plug to the power outlet or cigarette lighter socket. To avoid discharging the battery, we recommend running the engine. 8. Set the rocker switch on the compressor to I. The tyre is filled with sealant. 9. All of the sealant is pumped into the tyre. Then the tyre is inflated. Tyre pressure 3 138.
118 Vehicle care If tyre pressure is more than 1.8 bar, set it to the correct value. Repeat the procedure until there is no more loss of pressure. If the tyre pressure has fallen below 1.8 bar, the vehicle must not be used. Seek the assistance of a workshop. 15. Stow away tyre repair kit in load compartment. Notice The driving characteristics of the repaired tyre are severely affected, therefore have this tyre replaced.
Vehicle care Make the following preparations and observe the following information: ■ Park the vehicle on a level, firm and non-skid surface. The front wheels must be in the straight-ahead position. ■ Apply the parking brake and engage first or reverse gear. ■ Remove the spare wheel. ■ Never change more than one wheel at once. ■ Use the jack only to change wheels in case of puncture, not for seasonal winter or summer tyre change. ■ If the ground on which the vehicle is standing is soft, a solid board (max.
120 Vehicle care 4. Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping. With the jack correctly aligned, rotate until wheel is clear of the ground. 5. Unscrew the wheel nuts. 6. Change the wheel. 7. Screw on the wheel nuts. 8. Lower vehicle. 9. Install the wheel wrench ensuring that it locates securely and tighten each nut in a crosswise sequence. Tightening torque is 85 Nm (steel wheel) or 120 Nm (alloy wheel). 10.
Vehicle care 121 5. Unscrew knob 2 and release cable attachment 1 from spare wheel. 6. Change the wheel. 7. Position the replaced wheel at the rear of the vehicle with the outside of the wheel facing downwards. 2. Insert the wheel wrench into the aperture in the load compartment floor. 3. Rotate the wheel wrench to lower the spare wheel to the floor. 4. Withdraw spare wheel from under the vehicle. 8.
122 Vehicle care Have the defective tyre renewed or repaired as soon as possible. Jump starting Directional tyres Do not start with quick charger. A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle. Fit directional tyres such that they roll in the direction of travel. The rolling direction is indicated by a symbol (e.g. an arrow) on the sidewall. The following applies to tyres fitted opposing the rolling direction: ■ Driveability may be affected.
Vehicle care ■ The vehicles must not come into contact with each other during the jump starting process. ■ Apply the parking brake, transmission in neutral. Lead connection order: 1. Connect the red lead to the positive terminal of the booster battery. 2. Connect the other end of the red lead to the positive terminal of the discharged battery. 3. Connect the black lead to the negative terminal of the booster battery. 4.
124 Vehicle care Towing Towing the vehicle Release the cap by carefully lifting with a screwdriver. To prevent damage it is recommended to place a cloth between the screwdriver and the frame. The towing eye is stowed with the vehicle tools 3 113. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or better still a tow rod – to the towing eye. The towing eye must only be used for towing and not for recovering the vehicle.
Vehicle care The towing eye is stowed with the vehicle tools 3 113. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or even better a tow bar – to the towing eye. The towing eye must only be used for towing and not for recovering a vehicle. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. After towing, unscrew the towing eye. Insert cap.
126 Vehicle care Exterior lights Headlight and other light covers are made of plastic. Do not use any abrasive or caustic agents, do not use an ice scraper, and do not clean them dry. Polishing and waxing Wax the vehicle regularly (at the latest when water no longer beads). Otherwise, the paintwork will dry out. Polishing is necessary only if the paint has become dull or if solid deposits have become attached to it. Paintwork polish with silicone forms a protective film, making waxing unnecessary.
Vehicle care tank and the pressure valves on the vehicle underbody and the bulkhead in the engine compartment. These components must not be treated using chemical cleaners or preservatives. Have components of the natural gas system cleaned by a workshop authorised to carry out maintenance of natural gas vehicles. Towing equipment Do not clean the coupling ball bar with a steam-jet or high-pressure jet cleaner.
128 Service and maintenance Service and maintenance General information ................... 128 Recommended fluids, lubricants and parts .................................... 129 General information Confirmations In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified. The detailed, up-to-date service schedule for your vehicle is available at the workshop.
Service and maintenance Recommended fluids, lubricants and parts Recommended fluids and lubricants Only use products that meet the recommended specifications. Damage resulting from the use of products not in line with these specifications will not be covered by the warranty. 9 Warning Operating materials are hazardous and could be poisonous. Handle with care. Pay attention to information given on the containers. Engine oil Engine oil is identified by its quality and its viscosity.
130 Service and maintenance The system is factory filled with coolant designed for excellent corrosion protection and frost protection down to approx. -28 °C. This concentration should be maintained all year round. The use of additional coolant additives that intend to give additional corrosion protection or seal against minor leaks can cause function problems. Liability for consequences resulting from the use of additional coolant additives will be rejected.
Technical data Technical data Vehicle identification .................. 131 Vehicle data ............................... 133 131 Vehicle identification Vehicle Identification Number and in the floor on the front passenger side behind a cover. Identification plate The Vehicle Identification Number is visible through the windscreen The identification plate is in the engine compartment.
132 Technical data 8 = Engine type 9-11 = Vehicle-specific or countryspecific data Information on identification label: 1 = Type approval number 2 = Vehicle Identification Number 3 = Vehicle type identification code 4 = Permissible gross vehicle weight rating in kg 5 = Permissible gross train weight in kg 6 = Maximum permissible front axle load in kg 7 = Maximum permissible rear axle load in kg The combined total of front and rear axle loads must not exceed the permissible gross vehicle weight.
Technical data Vehicle data Engine data Sales designation 1.4 1.4 Engine identifier code 1.4i 1.4CNG Number of cylinders 4 4 1368 1368 Engine power [kW] 70 88 at rpm 6000 5000 Torque [Nm] 127 206 at rpm 4500 3000 Fuel type Petrol Compressed Natural Gas/Petrol recommended 95 95 possible 98 98 possible 91 91 Gas – CNG Oil consumption [l/1000 km] 0.6 0.
134 Technical data Sales designation 1.3 Turbo 1.6 Turbo 2.0 Turbo Engine identifier code 1.3CDTI 1.6CDTI1) 2.0CDTI Number of cylinders 4 4 4 1248 1598 1956 Engine power [kW] 66 66 / 77 99 at rpm 4000 4000 3500 Torque [Nm] 200 2002) / 290 320 at rpm 1500 1500 1500 Fuel type Diesel Diesel Diesel Oil consumption [l/1000 km] 0.6 0.6 0.6 Piston displacement 1) 2) [cm3] Low / High output. Vehicles with Manual Transmission Automated (MTA).
Technical data 135 Performance Engine 1.4i 1.4CNG 1.3CDTI 1.6CDTI3) 2.0CDTI 100 107 98 955) 986) / 102 111 – 955) – Maximum speed4) [mph] Manual transmission Manual Transmission Automated – – 986) /– Vehicle dimensions Type Van Wheelbase Short Long Short Length [mm] 4390 4740 4390 Width without exterior mirrors [mm] 1832 1832 Height (without antenna) [mm] Standard roof 1685 3) 4) 5) 6) 7) 8) Combi 1880 / 1832 19277) 1845 / 18958) Low / High output.
136 Technical data Type Van Combi High roof 1685 2115 / 2125 – Length of load compartment floor [mm] 1820 2170 950 Load compartment width [mm] 1230 1230 1230 Load compartment height [mm] Standard roof 1305 1305 1305 High roof 1455 – – Wheelbase [mm] 2755 3105 2755 Turning circle kerb to kerb [m] 11.2 12.5 11.
Technical data Capacities Engine oil Engine 14i 1.4CNG 1.3CDTI 1.6CDTI 2.0CDTI including Filter [l] 2.7 2.7 3.2 4.9 4.9 between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0 Fuel tank Petrol/diesel, nominal capacity [l] 60 Natural gas CNG, nominal capacity [kg] Petrol, nominal capacity [l] 16.15 kg9) / 22.1 kg10) 22 9) 10) SWB version. LWB version.
138 Technical data Tyre pressures Van Comfort with up to 2 people and 100 kg luggage With full load front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 185/65 R15 88T 250/2.5 (36) 250/2.5 (36) 230/2.3 (33) 280/2.8 (41) 185/65 R15 92T 250/2.5 (36) 260/2.6 (38) 290/2.9 (42) 300/3.0 (43) 195/65 R15 95T 240/2.4 (35) 240/2.4 (35) 260/2.6 (38) 270/2.7 (39) 195/60 R16C 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 330/3.3 (48) 360/3.
Technical data Combi Engine All 12) 13) 14) Comfort with up to 3 people With full load front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 185/65 R15, 250/2.5 (36) 250/2.5 (36) 230/2.3 (33) 280/2.8 (41) 185/65 R15, 250/2.5 (36) 260/2.6 (38) 290/2.9 (42) 300/3.0 (43) 195/65 R15, 240/2.4 (35) 240/2.4 (35) 260/2.6 (38) 260/2.6 (38) 195/60 R16C 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 280/2.8 (41)12) 360/3.
140 Customer information Customer information Vehicle data recording and privacy ....................................... 140 Vehicle data recording and privacy Event data recorders The vehicle has a number of sophisticated systems that monitor and control several vehicle data.
Customer information In addition, the manufacturer may use the collected or received diagnostic data: ■ for the manufacturer's research needs ■ to make it available for research needs where appropriate confidentiality is maintained and need is shown ■ to share summary data which is not tied to a specific vehicle with other organisations for research purposes Radio Frequency Identification (RFID) RFID technology is used in some vehicles for functions such as tyre pressure monitoring and ignition system secu
142 Index A Accessories and vehicle modifications ............................ 98 Adjustable air vents ..................... 76 Airbag and belt tensioners ........... 59 Airbag deactivation ................ 37, 59 Airbag system .............................. 35 Air conditioning regular operation 77 Air conditioning system ................ 74 Air intake ...................................... 77 Antilock brake system .................. 87 Antilock brake system (ABS) ....... 61 Anti slip-regulator..........
143 Doors...................................... 21, 23 Drain fuel filter ............................. 63 Driver Information Centre............. 64 Driving characteristics and towing tips ................................ 96 E Electric adjustment ...................... 25 Electrical system......................... 109 Electronic climate control system 74 Electronic driving programmes .... 86 Electronic stability program ......... 90 Electronic Stability Program fault.. 61 End-of-life vehicle recovery .....
144 K Keys ............................................. 18 Keys, locks................................... 18 L Lashing eyes ............................... 48 Light switch .................................. 68 Load compartment ................ 23, 46 Load compartment cover ............. 46 Load compartment lighting........... 72 Loading information ..................... 49 Low engine oil level ..................... 63 M Malfunction indicator light ............ 60 Manual adjustment ....................
145 T Tachometer ................................. 56 Tailgate......................................... 23 Tail lights ................................... 107 Three-point seat belt .................... 33 Tools .......................................... 113 Top-tether fastening eyes ............ 43 Towing.................................. 96, 124 Towing another vehicle ............. 124 Towing the vehicle ..................... 124 Traction Control system ............... 89 Trailer coupling.................
146
