Owner’s Manual Model Year 2013 Edition: August 2012 TS 1714-A-13 0-1 VAUXHALL Combo Owner’s Manual Model Year 2013 Edition: August 2012 TS 1714-A-13
Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 18 Seats, restraints ........................... 31 Storage ........................................ 48 Instruments and controls ............. 56 Lighting ........................................ 82 Climate control ............................. 88 Driving and operating ................... 94 Vehicle care ...............................
2 Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". Thank you for choosing a Vauxhall. We wish you many hours of pleasurable driving.
Introduction 5
6 In brief In brief Vehicle unlocking Unlocking with key Unlocking with radio remote control Initial drive information Turn the key in the driver's door lock towards the front of the vehicle. Press button Ä to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, press the button under the tailgate handle. Press button Å; only the load compartment is unlocked.
In brief Seat adjustment Seat backrests Seat height Turn handwheel. Do not lean on backrest when adjusting. Seat position 3 32, Seat adjustment 3 32. Lever pumping motion up = higher down = lower 7 Seat positioning Pull handle, slide seat, release handle. Seat position 3 32, Seat adjustment 3 32. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. Operate lever and adjust body weight on seat to raise or lower it.
8 In brief Head restraint adjustment Seat belt Mirror adjustment Interior mirror Press release catch, adjust height, engage. Head restraints 3 31. Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle. Seat position 3 32, Seat belts 3 36, Airbag system 3 39. Adjust the lever on the underside to reduce dazzle.
In brief Steering wheel adjustment Exterior mirrors Swivel lever in required direction. 9 Select the relevant exterior mirror by turning the control to left _ or right 6. Then swivel the control to adjust the mirror. In position o no mirror is selected. Convex exterior mirrors 3 26, Electric adjustment 3 26, Folding exterior mirrors 3 26, Heated exterior mirrors 3 27. Unlock the lever, adjust the steering wheel, then engage lever and ensure it is fully locked.
10 In brief Instrument panel overview
In brief 1 2 3 Fixed air vents ....................... 92 Side air vents ........................ 91 Light switch .......................... 82 4 Turn and lane-change signals, headlight flash, low beam and high beam ..... 84 Instruments .......................... 62 5 Driver Information Centre ...... 73 Windscreen wiper, windscreen washer system, rear wiper ................ 57 6 7 Trip reset ............................... 62 Centre air vents .................... 91 Headlight range adjustment .......
12 In brief Fog lights Press light switch > = front fog lights r = rear fog light Headlight flash, high beam and low beam headlight flash = pull lever high beam = push lever low beam = pull lever High beam 3 82, Headlight flash 3 82. Turn and lane-change signals lever up = right turn signal lever down = left turn signal Turn and lane-change signals 3 84.
In brief Hazard warning flashers Horn Washer and wiper systems Windscreen wiper Operated with the ¨ button. Hazard warning flashers 3 84. 13 Press j. Twist lever: É = fast È = slow Ç = intermittent wiping = off § For a single wipe when the windscreen wiper is off, move the lever up. Windscreen wiper 3 57, Wiper blade replacement 3 123.
14 In brief Windscreen and headlight washer systems Rear window wiper and washer systems Pull lever. Windscreen and headlight washer system 3 57, Washer fluid 3 121. Twist to activate the rear window wiper. The rear window wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged. Push lever: Washer fluid is sprayed on the rear window and the wiper wipes a few times. Rear window wiper/washer 3 58.
In brief Demisting and defrosting the windows Set the temperature control to V. Set fan to 4. Set air distribution control to V. Cooling n on. Heated rear window Ü on. Climate control system 3 88. Transmission 15 Manual transmission automated Manual transmission Reverse: with the vehicle stationary, wait 3 seconds after depressing the clutch pedal, pull up the collar on the selector lever and engage the gear.
16 In brief Starting off Starting the engine Stop-start system ■ Turn key to position MAR ■ move the steering wheel slightly to release the steering wheel lock ■ operate clutch and brake ■ do not operate accelerator pedal ■ diesel engines: turn the key to position MAR for preheating and wait until control indicator ! goes out ■ turn key to position AVV and release Starting the engine 3 95.
In brief Parking ■ Always apply the parking brake. Activate the manual parking brake without pressing the release button. Apply as firmly as possible on a downhill slope or uphill slope. Depress foot brake at the same time to reduce operating force. ■ Switch off the engine. Turn the ignition key to position STOP and remove it. Turn the steering wheel until the steering wheel lock is felt to engage. ■ If the vehicle is on a level surface or uphill slope, engage first gear.
18 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 18 Doors ........................................... 22 Vehicle security ............................ 25 Exterior mirrors ............................ 26 Interior mirrors ............................. 27 Windows ...................................... 27 Keys, locks Key with foldaway key section Keys Replacement keys The key number is specified in the Car Pass or on a detachable tag.
Keys, doors and windows Radio remote control Used to operate: ■ Central locking system 3 20 ■ Anti-theft locking system 3 25 ■ Power windows 3 27 The radio remote control has a range of up to 5 metres. It can be restricted by external influences. The hazard warning flashers confirm operation. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation.
20 Keys, doors and windows replace the battery (type CR 2032), paying attention to the installation position. Refit the battery holder in the key and secure the screw. Central locking system Unlocks and locks doors and load compartment. A pull on an interior door handle unlocks the entire vehicle and opens the respective door. Press button Ä: All doors, including rear doors / tailgate and sliding side doors are unlocked.
Keys, doors and windows Automatic locking The vehicle can be configured to automatically lock the doors when vehicle speed exceeds 12 mph. Driver Information Centre (DIC) 3 73. Unlocking the load compartment from inside the vehicle Press button Å: The load compartment (rear doors / tailgate and sliding side doors) are unlocked. When the load compartment is locked, the LED in the button is illuminated. Child locks 9 Warning Use the child locks whenever children are occupying the rear seats.
22 Keys, doors and windows Doors Caution Sliding door To avoid damage, do not attempt to operate the sliding side door when the fuel filler flap is open. Refuelling 3 112. Emergency lock Using a key or suitable screwdriver, turn the emergency lock switch on the sliding side door to locked position 1. The door cannot be opened from outside. The emergency lock remains engaged even after unlocking the vehicle with the remote control. To disengage, turn the switch to unlocked position 2.
Keys, doors and windows The right hand rear door is released using the lever. 9 Warning The door is opened from inside the vehicle by pressing down the interior handle. The rear lights may be obscured if the rear doors are open and the vehicle is parked on the roadside. Make other road users aware of the vehicle, by using a warning triangle or other equipment specified in the road traffic regulations. 23 The doors are retained in the 90º position by locking stays.
24 Keys, doors and windows Load compartment Tailgate Caution Before opening the tailgate check overhead obstructions, such as a garage door, to avoid damage to the tailgate. Always check the moving area above and behind the tailgate. Opening Note The installation of certain heavy accessories onto the tailgate may affect its ability to remain open. Closing Press the button underneath the moulding. 9 Warning Do not drive with the tailgate open or ajar, e.g.
Keys, doors and windows Vehicle security Activating Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. The system deadlocks all the doors. All doors must be closed otherwise the system cannot be activated.
26 Keys, doors and windows Exterior mirrors Electric adjustment Folding Select the relevant exterior mirror by turning the control to left _ or right 6. Then swivel the control to adjust the mirror. In position o no mirror is selected. For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing.
Keys, doors and windows Heated Interior mirrors Windows Manual anti-dazzle Windscreen 27 Windscreen stickers Do not attach stickers such as toll road stickers or similar on the windscreen in the area of the interior mirror. Manual windows Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. The door windows can be opened or closed with the window winders.
28 Keys, doors and windows Keep a close watch on the windows when closing them. Ensure that nothing becomes trapped in them as they move. Switch on ignition to operate power windows. Pushing or pulling firmly and then releasing: window moves up or down fully with safety function enabled. To stop movement, operate the switch once more in the same direction. With the ignition key removed or in the STOP position, the windows can be operated for approx.
Keys, doors and windows Rear windows Child safety system for rear windows Press switch , to deactivate rear door power windows. To activate, press , again. Operating windows from outside The windows can be operated remotely from outside the vehicle when locking or unlocking the vehicle. Central locking system 3 20. 29 Opening rear windows Press and hold the Ä button to open windows. Press and hold the e button to close windows. Release button to stop window movement.
30 Keys, doors and windows Heated rear window Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Sun visors The sun visors can be folded down or swivelled to the side to prevent dazzling. If the sun visors have integral mirrors, the mirror covers should be closed when driving. A ticket holder is located on the backside of the sun visor.
Seats, restraints Seats, restraints Head restraints ............................ 31 Front seats ................................... 32 Rear seats ................................... 34 Seat belts ..................................... 36 Airbag system .............................. 39 Child restraints ............................. 43 Head restraints 31 Adjustment Head restraints on front seats Position 9 Warning Only drive with the head restraint set to the proper position.
32 Seats, restraints Head restraints on rear seats Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. Height adjustment Pull the head restraint upwards or press the catch to release and push the head restraint downwards. Removal Press both catches, pull the head restraint upwards and remove. Note Approved accessories may only be attached if the seat is not in use. ■ Sit with buttocks as far back against the backrest as possible.
Seats, restraints 9 Danger Seat backrests Seat height Turn handwheel. Do not lean on backrest when adjusting. Lever pumping motion up = higher down = lower 33 Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat positioning Operate lever and adjust body weight on seat to raise or lower it. Pull handle, slide seat, release handle.
34 Seats, restraints Armrest Heating Rear seats Third row seats 9 Warning Never adjust seats while driving as they could move uncontrollably. Folding the seats The load compartment area can be increased by folding up the rear seats. Raise or lower the armrest as required. Activate heating by pressing ß button for the seat with the ignition on. LED in button ß on: relevant front seat heating on. Prolonged use for people with sensitive skin is not recommended.
Seats, restraints ■ Pull the release lever and fold down the backrest onto the seat cushion. Pull the lower strap and fold the seat assembly forwards. ■ Secure the folded seat in the upright position by attaching the flexible cord located on the seat frame, to the rear seat head restraint. ■ To lower the seat, remove the flexible cord and lower the seat assembly to the floor, ensuring the rear support is located on the anchor point and securely latched. ■ Raise the backrest and adjust the head restraint.
36 Seats, restraints Replacing the seats ■ Raise the backrest and replace the head restraint. ■ The backrest is properly engaged when red mark on the release lever is no longer visible. Seat belts 9 Warning ■ Attach the seat assembly front supports on the anchor points. ■ Push the release lever to ensure the seat is securely latched. ■ Remove the head restraint from the rear of the seat frame.
Seats, restraints Seat belts are designed to be used by only one person at a time. Child restraint system 3 43. Periodically check all parts of the belt system for damage, pollution and proper functionality. Have damaged components replaced. After an accident, have the belts and triggered belt pretensioners replaced by a workshop. Note Make sure that the belts are not damaged by shoes or sharp-edged objects or trapped. Prevent dirt from getting into the belt retractors. Seat belt reminder X 3 67.
38 Seats, restraints Height adjustment Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing. 1. Pull belt out slightly. 2. Press button down. 3. Adjust height and engage. Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving.
Seats, restraints Removing To release belt, press red button on belt buckle. Seat belts on the rear seats The seat belt for the rear centre seat can only be withdrawn from the retractor if the backrest is in the rear position. Using the seat belt while pregnant 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen. 39 Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment.
40 Seats, restraints 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner. Note The airbag systems and belt pretensioner control electronics are located in the centre console area. Do not put any magnetic objects in this area. Do not fix any objects onto the airbag covers and do not cover them with other materials. Each airbag is triggered only once. Have deployed airbags replaced by a workshop.
Seats, restraints 9 Warning Optimum protection is only provided when the seat is in the proper position 3 32. Keep the area in which the airbag inflates clear of obstructions. Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system The side airbag system consists of an airbag in each front seat backrest. This can be identified by the word AIRBAG. The side airbag system is triggered in the event of a side impact of a certain severity.
42 Seats, restraints Deactivate the front passenger airbag system as follows: 1. Press the SET ESC button once to access the settings menu. 2. Press SET ESC again (repeatedly) to cycle through the menu functions until menu option Pass bag (in Standard version) - or Passenger bag (in Multifunction version) is displayed. 3. Press the R or S button to switch from Pass bag On to Pass bag off (Standard version) - or from Passenger bag On to Passenger bag Off (Multifunction version) 4.
Seats, restraints Child restraints Child restraint systems We recommend the Vauxhall child restraint system which is tailored specifically to the vehicle. When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system. Always comply with local or national regulations. In some countries, the use of child restraint systems is forbidden on certain seats.
44 Seats, restraints Child restraint installation locations Permissible options for fitting a child restraint system Front passenger seat Second row Third row Weight and age class activated airbag deactivated airbag outboard seat centre seat Group 0: up to 10 kg or approx. 10 months X U1 U, < U X Group 0+: up to 13 kg or approx. 2 years X U1 U, < U X Group I: 9 to 18 kg or approx. 8 months to 4 years X U1 U, < U X Group II: 15 to 25 kg or approx.
Seats, restraints 45 Permissible options for fitting an ISOFIX child restraint system On front passenger seat On outboard seats On centre seat in On the seats in in the second row the second row the third row Weight class Size class Fixture Group 0: up to 10 kg E ISO/R1 X IL X X Group 0+: up to 13 kg E ISO/R1 X IL X X D ISO/R2 X IL X X C ISO/R3 X IL1) X X D ISO/R2 X IL X X C ISO/R3 X IL1) X X B ISO/F2 X IUF X X B1 ISO/F2X X IUF X X A ISO/F3 IUF X X Group
46 Seats, restraints ISOFIX size class and seat device A – ISO/F3 B – ISO/F2 B1 – ISO/F2X C – ISO/R3 D – ISO/R2 E – ISO/R1 = = = = = = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. ISOFIX mounting brackets are indicated by a label on the backrest. Before fastening a child seat adjust the head restraint to use position 3 31. Top-tether fastening eyes In addition to the ISOFIX mounting, fasten the Top-Tether strap to the Top-Tether fastening eyes.
48 Storage Storage Storage compartments Document holder Instrument panel storage Storage compartments ................ 48 Load compartment ....................... 50 Roof rack system ......................... 53 Loading information ..................... 54 Storage compartments are located in the instrument panel. Pull the rear of the document holder upwards from the instrument panel and rest in tilted position.
Storage 49 Glovebox Overhead console Underseat storage To open the glovebox, pull the handle. Depending on version, the glovebox may be lockable. The glovebox should be closed whilst driving. Store only lightweight items such as paperwork or maps in the overhead console. Pull the loop on the seat cushion to gain access to the storage area. Cupholders Cupholders are located in the centre console. The cupholders can also be used to hold the portable ashtray unit 3 61.
50 Storage Load compartment To fold up, lower seats to the floor until they engage audibly. Raise backrests and guide them into an upright position until they engage audibly. The backrests are properly engaged when both red marks on the release levers are no longer visible. Ensure that the seat belts are positioned correctly before returning the seats to the upright position. Folding down rear seat backrests The rear seat backrest is divided into two parts. Both parts can be folded down.
Storage 51 Closing Opening Removing Pull the cover towards the rear using the handle and engage it in the retainers at the sides. Remove load compartment cover from the retainers at the sides. Hold the cover and guide it until it is fully rolled up. Open the load compartment cover. Pull the release lever and lift cover from retainers. Installing Insert either side of the load compartment cover in the recess, pull the release lever. Insert the load compartment cover and engage.
52 Storage Rear parcel shelf or the lower position. In the lower position, the maximum load permissible is 70 kg. The rear parcel shelf consists of two parts - a front part and rear part. The front part can be opened or closed, allowing for greater flexibility in the load compartment. Do not place any excessively heavy or sharp-edged objects on the rear parcel shelf.
Storage To remove, lift the front part of the parcel shelf by releasing it from the front retainers (1) on both sides. Lift the rear part of the parcel shelf by releasing it from the rear retainers (2 and 3) on both sides. Installing Refit the parcel shelf by engaging in front and rear retainers on both sides. Lashing eyes Van 53 The lashing eyes are designed to secure items against slippage, e.g. using lashing straps or a luggage net.
54 Storage To fasten a roof rack, insert the mounting bolts in the holes indicated in the illustration. Loading information ■ Heavy objects in the load compartment should be evenly distributed and placed as far forward as possible. If objects can be stacked, the heavier objects should be placed at the bottom. ■ Secure objects with lashing straps attached to lashing eyes 3 53. ■ Secure loose objects in load compartment to prevent sliding.
Storage Optional equipment and accessories increase the kerb weight. ■ Driving with a roof load increases the sensitivity of the vehicle to cross-winds and has a detrimental effect on vehicle handling due to the vehicle's higher centre of gravity. Distribute the load evenly and secure it properly with retaining straps. Adjust the tyre pressure and vehicle speed according to the load conditions. Check and retighten the straps frequently. Do not drive faster than 75 mph.
56 Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Controls ....................................... 56 Warning lights, gauges and indicators ..................................... 62 Information displays ..................... 73 Vehicle messages ........................ 79 Trip computer ............................... 80 Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked.
Instruments and controls Horn Windscreen wiper/washer Windscreen wiper 57 Adjustable wiper interval Wiper lever in position Ç. The windscreen wiper will automatically adapt to the speed of the vehicle. Windscreen washer Press j. Twist É È Ç § = = = = fast slow intermittent wiping off For a single wipe when the windscreen wiper is off, move the lever up. Do not use if the windscreen is frozen. Switch off in car washes.
58 Instruments and controls Rear window wiper/washer Outside temperature Clock Depending on model variant, the current time and/or date may appear in the Driver Information Centre (DIC) 3 73. Values can be adjusted via the SET ESC, R and S buttons on the instrument panel. Twist to activate the rear window wiper. Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times. Do not use if the rear window is frozen. Switch off in car washes.
Instruments and controls Set time in Driver Information Centre - Standard version 6. Press R or S to increase or decrease the displayed value. 7. Press SET ESC briefly to confirm changes and automatically return to the previous display screen. Set time and date in Driver Information Centre Multifunction version 1. Press the SET ESC button once to access the settings menu. 2. Scroll through the menu options using the R or S buttons until HOUR is displayed. 3.
60 Instruments and controls To change the clock mode between 12 hour and 24 hour clock: 1. Press R or S to select Mode and press SET ESC to access this submenu option; the display will flash. 2. Press R or S to change clock mode between 12h and 24h. 3. Press SET ESC briefly to confirm changes and automatically return to the previous display screen. Setting the date 1. Press the SET ESC button once to access the settings menu. 2.
Instruments and controls Long wheelbase van Combo Tour Do not exceed the maximum power consumption of 180 watts. With ignition off, the power outlets are deactivated. Additionally the power outlets are deactivated in the event of low battery voltage. Electrical accessories that are connected must comply with the electromagnetic compatibility requirements laid down in DIN VDE 40 839. Do not connect any current-delivering accessories, e.g. electrical charging devices or batteries.
62 Instruments and controls Warning lights, gauges and indicators Odometer Speedometer The portable ashtray should be placed in the cupholders in the centre console. Indicates vehicle speed. Displays the recorded distance in miles. H may appear in the display until the vehicle has travelled 60 miles. Trip odometer Displays the recorded distance since the last reset.
Instruments and controls To reset the trip odometer, press and hold the TRIP button for a few seconds while the relevant trip odometer is displayed. Tachometer Caution If the needle is in the red warning zone, the maximum permitted engine speed is exceeded. Engine at risk. Fuel gauge 63 Never run the tank dry. Because of the fuel remaining in the tank, the top-up quantity may be less than the specified tank capacity.
64 Instruments and controls the cylinders. As the fuel level diminishes, the bars in the CNG fuel gauge disappear. CNG and the one remaining bar will flash if the methane level in the cylinders is low. Refuelling 3 112. Engine coolant temperature gauge Caution If engine coolant temperature is too high, stop vehicle, switch off engine. Danger to engine. Check coolant level. Fuel selector Y illuminates in the Driver Information Centre.
Instruments and controls 3 73. Based on driving conditions, the interval at which a service will be indicated can vary considerably. When the remaining distance before the next service is less than 1,250 miles, Serv. appears in the Driver Information Centre. The service reminder is repeated after every additional 125 miles and becomes more frequent when the remaining distance is below 125 miles. The vehicle needs a service. Seek the assistance of a workshop.
66 Instruments and controls Control indicators in the instrument cluster
Instruments and controls Generic warning 9 illuminates yellow. Depending on model variant, control indicator 9 may illuminate independently or in conjunction with Æ, t, Z or r. If 9 illuminates together with I; stop engine immediately and seek the assistance of a workshop. Simultaneously a warning message may be displayed in the Driver Information Centre (DIC) 3 73. 9 also illuminates if the fuel cut-off switch is triggered, or if a fault is detected in the engine oil pressure sensor. Consult a workshop.
68 Instruments and controls driving, there is a fault in the airbag system. Seek the assistance of a workshop. The airbags and belt pretensioners may fail to trigger in the event of an accident. Deployment of the belt pretensioners or airbags is indicated by continuous illumination of v. 9 Warning Have the cause of the fault remedied immediately by a workshop. Belt pretensioners, airbag system 3 36, 3 39. Airbag deactivation * illuminates yellow.
Instruments and controls Flashes when the engine is running Fault that could lead to catalytic converter damage. Ease up on the accelerator until the flashing stops. Seek the assistance of a workshop immediately. Brake system R illuminates red. Illuminates when the parking brake is released if the brake fluid level is too low 3 122. 9 Warning Stop. Do not continue your journey. Consult a workshop. Illuminates if the brake vacuum servo fails; the brake pedal becomes stiff when pressed.
70 Instruments and controls message may also be displayed in the Driver Information Centre (DIC) 3 73. Generic warning 9 3 67. Ultrasonic parking assist 3 108. Generic warning 9 3 67. Hill start assist 3 105. Electronic Stability Program fault Ultrasonic parking assist x illuminates or flashes yellow. r illuminates yellow. Fault in system or Fault due to sensors that are dirty or covered by ice or snow or Interference due to external sources of ultrasound.
Instruments and controls Preheating ! illuminates yellow. Preheating is activated. Only activates when outside temperature is low. Diesel particle filter [ illuminates yellow. The diesel particle filter requires cleaning. Continue driving until [ extinguishes. If possible, do not allow engine speed to drop below 2000 rpm. Illuminates The diesel particle filter is full. Start cleaning process as soon as possible. Diesel particle filter 3 98, Stop-start system 3 96. Engine oil pressure I illuminates red.
72 Instruments and controls Centre (DIC), to indicate that engine oil life has been diminished and the oil needs changing. Based on driving conditions, the interval at which an oil change will be indicated can vary considerably. Depending on model variant, I may flash in the following ways: ■ for 1 minute every 2 hours, or ■ for 3 minute cycles with I off for intervals of 5 seconds.
Instruments and controls Depending on version, 9 will illuminate as an alternative if control indicator Æ is not present. A warning message may also be displayed in the Driver Information Centre (DIC) 3 73. Generic warning 9 3 67. Stop-start system 3 96. Exterior light 8 illuminates green. The exterior lights are on 3 82. Exterior light failure µ illuminates yellow. One or more of the exterior lights is faulty 3 124.
74 Instruments and controls ■ ■ ■ ■ Transmission display 3 100 Stop-start system indicator 3 96 Vehicle messages 3 79 Trip computer 3 80 Selecting menus and options The menus and options can be selected via the buttons on the instrument panel. and a Multifunction version with further adjustable settings. Some of the displayed functions differ when the vehicle is being driven or at a standstill. Some options are only available when the vehicle is being driven.
Instruments and controls Settings menu options Standard version Press the R button to scroll up the screen and the menu options or to increase the displayed value. Press and hold to increase value rapidly (press again to stop on the required value). Press the S button to scroll down the screen and the menu options or to decrease the displayed value. Press and hold to decrease value rapidly (press again to stop on the required value).
76 Instruments and controls BAG P (Passenger front and side airbags activation/deactivation) Activate the front passenger airbags if an adult is occupying the front passenger seat. Deactivate airbags when a child restraint system is installed on this seat. 9 Danger Risk of fatal injury for a child using a child restraint system on a seat with activated front passenger airbag. Risk of fatal injury for an adult person on a seat with deactivated front passenger airbag.
Instruments and controls Press the SET ESC button when activated (On) to access the current set speed. Adjust as required and confirm. Warning chimes 3 79. TRIP B DATA Activate or deactivate the second trip computer (set to On or Off). Trip B records average consumption, distance travelled, average speed and travel time (driving time). The measurement can be restarted at any time. Trip computer 3 80.
78 Instruments and controls BUTTON VOLUME A chime is sounded every time the SET ESC, R or S button is pressed. Adjust the volume of these chimes and confirm. 8 volume levels are available. Warning chimes 3 79. SEAT BELT BUZZER (Reactivate warning chime for driver and/or front passenger seat belt reminder) This menu option is available only when the seat belt reminder has already been deactivated by a workshop.
Instruments and controls Vehicle messages Warning chimes Only one warning chime will sound at a time. When starting the engine or whilst driving ■ If seat belt is not fastened. ■ If a certain speed is exceeded with the parking brake applied. ■ If the parking assist detects an object. ■ If a fault is detected in the parking assist. ■ If a door or the tailgate is not fully closed when starting-off. ■ If the vehicle speed briefly exceeds a set limit.
80 Instruments and controls Trip computer The trip computer provides information on driving data, which is continually recorded and evaluated electronically. The following functions can be selected by pressing the TRIP button repeatedly on the end of the wiper lever: Standard version ■ Average consumption ■ Instantaneous consumption ■ Range ■ Distance travelled ■ Average speed ■ Travel time (driving time) Trip B can be deactivated via the Driver Information Centre (DIC) 3 73.
Instruments and controls The trip computer will reset automatically when the maximum value of any of the parameters is exceeded. Average consumption Average consumption is displayed, taking into consideration the distance travelled and the fuel used since the last reset. The measurement can be restarted at any time. Instantaneous consumption Display of the instantaneous fuel consumption. _ _ _ _ will appear in the display if the vehicle is left parked with the engine running for a long time.
82 Lighting Lighting Exterior lighting High beam Light switch Exterior lighting ............................ 82 Interior lighting ............................. 85 Turn light switch: § = off / daytime running lights 9 = sidelights / headlights Control indicator 8 3 73. Tail lights Tail lights are illuminated together with headlights and sidelights. To switch from low to high beam, push lever. To switch to low beam, pull lever. Headlight flash To activate the headlight flash, pull lever.
Lighting Headlight range adjustment Manual headlight range adjustment To adapt headlight range to the vehicle load to prevent dazzling: Press À or Á buttons until the required setting is displayed in the Driver Information Centre (DIC) 3 73.
84 Lighting Hazard warning flashers Turn and lane-change signals Switch the indicator off manually by moving the lever to its original position. Front fog lights Operated with the ¨ button. Lever up = right turn signal Lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel moves back, the turn signal is automatically deactivated. For five flashes, e.g.
Lighting Rear fog lights Misted light covers The inside of the light covers may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing. The mist disappears quickly by itself; to help, switch on the headlights. Operated with the r button. The rear fog light can only be switched on when both the ignition and headlights or sidelights (with front fog lights) are on. Press the button again to turn the rear fog light off, or turn off the headlights and/or the front fog lights.
86 Lighting Multifunction version of DIC 1. Press the SET ESC button to access the settings menu. 2. Scroll through the menu options using the R or S buttons until menu option LIGHTING appears in the display. 3. Press the R or S button to increase or decrease the displayed value. 4. Press SET ESC briefly to confirm changes and automatically return to the previous display screen. It is also possible to adjust the brightness using the R or S buttons without accessing the settings menu.
Lighting Rear courtesy lights Removable rear courtesy light Centre switch position: automatic interior light. To operate manually when the doors are closed, press the lens on either side. Depending on model variant, the removable rear courtesy light may illuminate when the rear doors / tailgate or sliding side doors are opened and the central switch is in the middle position. Switch the light on permanently by pressing the top part of the central switch c.
88 Climate control Climate control Climate control systems ............... 88 Air vents ....................................... 91 Maintenance ................................ 92 Climate control systems Heating and ventilation system Heating will not be fully effective until the engine has reached normal operating temperature. Fan speed Adjust the air flow by switching the fan to the desired speed.
Climate control ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J. Air conditioning system Cooling (AC) Operated with the AC button and functional only when the engine and fan are running. The air conditioning system cools and dehumidifies (dries) the air when outside temperature is a little above the freezing point. Therefore condensation may form and drip from under the vehicle.
90 Climate control Electronic climate control system Controls for: ■ Temperature ■ Air distribution and menu selection ■ Fan speed AUTO = Automatic mode = air recirculation 4 Ê = demisting and defrosting OFF = switch on/off Heated rear window Ü 3 30. The preselected temperature is automatically regulated. In the automatic mode the fan speed and air distribution automatically regulate the air flow. The system can be manually adapted by use of air distribution and air flow controls.
Climate control Demisting and defrosting the windows Press the Ê button. Temperature and air distribution are set automatically and the fan runs at a high speed. When the vehicle reaches normal operating temperature the function remains active for approx. 3 minutes. To return to automatic mode: press button n or AUTO. Air distribution Press R, S and 6 buttons. LED in buttons illuminate. Arrows shown in the display indicate the distribution settings.
92 Climate control Slide knob to the left to open vent. Direct the flow of air by swivelling the vent. Slide knob to the right to close vent. Fixed air vents Additional air vents are located beneath the windscreen and door windows and in the foot wells. Maintenance Air intake Side air vents Slide knob to the left to open vent. Direct the flow of air by swivelling the vent. Slide knob to the right to close vent.
Climate control Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low.
94 Driving and operating Driving and operating Driving hints ................................. 94 Starting and operating ................. 94 Engine exhaust ............................ 98 Manual transmission .................. 100 Manual transmission automated .................................. 100 Brakes ........................................ 104 Ride control systems ................. 106 Cruise control ............................. 107 Object detection systems ........... 108 Fuel ...................
Driving and operating Ignition switch positions Starting the engine 95 Starting the vehicle at low temperatures The start of the engine without additional heaters is possible down to -25 °С for diesel engines and -30 °C for petrol engines. Required is an engine oil with the correct viscosity, the correct fuel, performed services and a sufficiently charged battery.
96 Driving and operating Note In addition, the vehicle is automatically unlocked and the interior lights are illuminated. Turn the ignition key to position STOP to prevent battery discharge and seek the assistance of a workshop immediately. Have the vehicle checked for fuel leaks in the engine compartment, beneath the vehicle and near the fuel tank. To reset the fuel cut-off system and enable the vehicle to be driven: 1. Turn the ignition key to position MAR 3 95 2.
Driving and operating Deactivate the stop-start system manually by pressing the ^ button in the centre console. LED in the button illuminates to confirm deactivation. Autostop If the vehicle is at a low speed or at a standstill, activate an Autostop as follows: ■ Depress the clutch pedal ■ set the lever to neutral ■ release the clutch pedal The engine will be switched off while the ignition stays on. An Autostop is indicated when ^ flashes in the Driver Information Centre (DIC) 3 73.
98 Driving and operating The selector lever must be in neutral to enable an automatic restart. Depress the clutch pedal to restart the engine. Manual transmission automated If the lever is in position N, select another gear, otherwise release the brake pedal or move the lever to +, – or R. When one of the following conditions occurs during an Autostop, the engine will need to be restarted manually using the key.
Driving and operating take up to 25 minutes. Typically it needs 15 minutes. Autostop is not available and fuel consumption may be higher during this period. The emission of smells and smoke during this process is normal. Under certain driving conditions, e.g. short distances, the system cannot clean itself automatically. If the cleaning of the filter is required and if previous driving conditions did not enable automatic cleaning, it will be indicated by control indicator [.
100 Driving and operating Manual transmission Caution It is not advisable to drive with the hand resting on the selector lever. When gearshifting is recommended to improve fuel economy, control indicator [ or Ò illuminates in the Driver Information Centre (DIC) 3 69. Manual transmission automated The manual transmission automated (MTA) permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control.
Driving and operating Starting the engine Selector lever Depress the foot brake when starting the engine. If the foot brake is not depressed, a warning message appears in the Driver Information Centre (DIC) in conjuction with a warning chime 3 79 and the engine cannot be started. Note The volume of the warning chime can also be adjusted via the DIC. Driver Information Centre (DIC) 3 73. When the foot brake is depressed, the transmission automatically shifts to N (neutral) and the engine can be started.
102 Driving and operating start off quickly, release the foot brake and accelerate immediately after engaging a gear. Move the selector lever towards A/M to engage automatic mode; the transmission shifts to other gears automatically, dependent on driving conditions. To engage manual mode, move the selector lever towards A/M. The current gear will appear in the transmission display.
Driving and operating Manual mode If engine speed is too low, the transmission automatically shifts to a lower gear. In manual mode, no automatic shifting to a higher gear takes place at high engine revolutions. If engine speed is too high, the transmission only switches to a higher gear via kickdown. Kickdown 3 103. Electronic driving programmes Eco mode E When automatic mode is engaged, the Eco mode can be selected to reduce fuel consumption.
104 Driving and operating If engine speed is too high the transmission switches to a higher gear, even in manual mode. Without kickdown this automatic shift is not effected in manual mode. Fault In the event of a fault, control indicator Ñ is shown in the transmission display. Continued driving is possible, provided the vehicle is driven with care and anticipation. A warning message may appear in the Driver Information Centre (DIC) in conjunction with a warning chime 3 79.
Driving and operating hard braking, the vehicle can no longer be steered and may swerve. Have the cause of the fault remedied by a workshop. Parking brake Manual parking brake To release the parking brake, pull the lever up slightly, press the release button and fully lower the lever. To reduce the operating forces of the parking brake, depress the foot brake at the same time. A warning chime will sound if a certain speed is exceeded with the parking brake applied.
106 Driving and operating Ride control systems Traction Control system The Anti-Slip Regulator (ASR) is a component of the Electronic Stability Control system. ASR improves driving stability when necessary, regardless of the type of road surface or tyre grip, by preventing the drive wheels from spinning. As soon as the drive wheels starts to spin, engine output is reduced and the wheel spinning the most is braked individually.
Driving and operating considerably improves the driving stability of the vehicle on slippery road surfaces. ESP is operational as soon as control indicator x extinguishes. When ESP comes into action x flashes. The ESP system is automatically activated when the vehicle is started and cannot be deactivated Seek the assistance of a workshop. Control indicator x 3 70. 107 Cruise control The cruise control can store and maintain speeds above approx. 20 mph.
108 Driving and operating Switching on Turn end of lever ON, control indicator m illuminates in the instrument cluster in conjunction with a message in the driver information centre. Reduce speed With cruise control active, push lever downwards - or briefly push lever downwards - repeatedly: speed decreases continuously or in small increments.
Driving and operating System operation The parking assist is turned on automatically when reverse gear is engaged. The intervals between the beeps become shorter as the vehicle gets closer to the obstacle. When the distance is less than 30 cm, the beeping is a continuous tone which stops immediately when the distance is increased. Fault In the event of a fault in the system, r illuminates and a message is displayed in the Driver Information Centre (DIC) 3 73.
110 Driving and operating Caution Performance of the sensor can be reduced when sensors are covered, e.g. by ice or snow. Performance of the parking assist systems can be reduced due to heavy loading. Special conditions apply if there are taller vehicles involved (e.g. off-road vehicles, mini vans, vans). Object identification in the upper part of these vehicles cannot be guaranteed.
Driving and operating Caution Do not use fuel or fuel additives that contain metallic compounds such as manganese-based additives. This may cause engine damage. Caution Use of fuel that does not comply to EN 228 or E DIN 51626-1 or equivalent can lead to deposits or engine damage and may affect your warranty. Caution Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage. Fuel for diesel engines Only use diesel fuel that complies with EN 590.
112 Driving and operating Pressing button Y in the centre console switches between petrol and natural gas operation. The LED 1 status shows the current operating mode. 1 off = natural gas operation. 1 illuminates = petrol operation. As soon as the natural gas tanks are empty, petrol operation is automatically engaged. Control indicator Y illuminates in the Driver Information Centre (DIC) 3 73 until the ignition is switched off. A slight loss of power and torque can be expected in petrol operation.
Driving and operating Note Depending on model, the sliding side door may be fitted with a safety system that prevents the door from being opened fully when the fuel filler flap is open. Sliding side door 3 22. Caution Wipe off any overflowing fuel immediately. To close, replace fuel filler cap and turn clockwise. Insert key into fuel filler cap and turn clockwise to lock, then remove key. Close the fuel filler flap.
114 Driving and operating Terms for "natural gas" abroad: German Erdgas English CNG = Compressed Natural Gas French GNV = Gaz Naturel (pour) Véhicules - or CGN = carburantgaz naturel Italian Metano (per auto) Fuel filler cap Only use genuine fuel filler caps. Diesel-engined vehicles have special fuel filler caps. Fuel cut-off system In the event of a collision of a certain severity, the fuel system is cut-off and the engine is switched off automatically, for safety reasons.
Driving and operating Towing General information Only use towing equipment that has been approved for your vehicle. Vehicles with natural gas engine may require special towing equipment. Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment. Fitting of towing equipment could cover the opening of the towing eye. If this is the case use the coupling ball bar for towing.
116 Driving and operating The maximum permissible vertical coupling load (75 kg) is specified on the towing equipment identification plate and in the vehicle documents. Always aim for the maximum load, especially in the case of heavy trailers. The vertical coupling load should never fall below 25 kg. Rear axle load The permissible axle loads (see identification plate or vehicle documents) must not be exceeded.
Vehicle care Vehicle care General Information ................... 117 Vehicle checks ........................... 118 Bulb replacement ....................... 124 Electrical system ........................ 130 Vehicle tools .............................. 133 Wheels and tyres ....................... 134 Jump starting ............................. 143 Towing ....................................... 145 Appearance care .......................
118 Vehicle care ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.g. anti-theft locking system. Putting back into operation When the vehicle is to be put back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir.
Vehicle care 119 Closing 9 Danger Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged. The ignition system uses extremely high voltage. Do not touch. Engine oil Bonnet Opening Push the safety catch and open the bonnet. Check the engine oil level manually on a regular basis to prevent damage to the engine. Ensure that the correct specification of oil is used. Recommended fluids and lubricants 3 151. Check with the vehicle on a level surface.
120 Vehicle care Engine coolant Insert dipstick to the stop on the handle and make half a turn. The coolant provides freeze protection down to approx. -28 °C. In northern countries with very low temperatures, the factory filled coolant provides frost protection down to approx. -37°C. Caution Only use approved antifreeze. When the engine oil level has dropped to the MIN mark, top up engine oil. We recommend the use of the same grade of engine oil that was used at last change.
Vehicle care the coolant concentration checked and have the cause of the coolant loss remedied by a workshop. 121 Washer fluid Power steering fluid If the cooling system is cold, the coolant level should be between the MIN and MAX mark. Top up if the level is low. 9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly. To top up use a 1:1 mixture of released coolant concentrate mixed with clean tap water.
122 Vehicle care Brakes Battery A squealing noise, or illumination of brake pad wear control indicator F indicates that the brake lining is at its minimum thickness. Continued driving is possible but have the brake linings replaced as soon as possible. Once new brake linings are installed, do not brake unnecessarily hard for the first few journeys. Brake pad wear indicator F 3 69. The vehicle battery is maintenancefree provided that the driving profile allows sufficient charging of the battery.
Vehicle care The anti-theft alarm siren must be deactivated as follows: Switch the ignition on then off, disconnect the vehicle's battery within 15 seconds. Replacing the battery Note Any deviation from the instructions given in this paragraph may lead to a temporary deactivation of the stopstart system. volts when using a battery charger. Otherwise the battery might be damaged.
124 Vehicle care Wiper blade on tailgate Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. Replace headlight bulbs from within the engine compartment. Lift wiper arm, press retaining clips to detach wiper blade. Attach the wiper blade to the wiper arm and push until it engages. Lower wiper arm carefully.
Vehicle care 5. Attach connector to bulb. 6. Engage wire clip. 7. Install protective cover. High beam 1. Remove protective cover. 2. Detach connector from bulb. 3. Disengage wire clip and remove bulb from reflector. 4. Insert new bulb in reflector so that the bulb aligns with the reflector recess. 5. Engage wire clip, plug connector onto bulb. 6. Install protective cover. 125 Daytime running light 1. Remove protective cover. Side light 1. Remove protective cover.
126 Vehicle care Tail lights 2. Withdraw bulb holder from reflector by turning anticlockwise. 3. Push bulb into holder slightly, rotate anticlockwise, remove and renew bulb. 4. Insert bulb holder in reflector. 5. Rotate clockwise to engage. 6. Install protective cover. 1. Remove three retaining screws. 2. Remove light housing from vehicle. 3. Disengage connector plug from bulb holder. 4. Unscrew the four retaining screws using a screwdriver.
Vehicle care 9. Engage connector plug. 10. Insert light housing in body, ensuring proper positioning. Tighten three retaining screws. 127 Number plate light Tailgate Side turn signal lights Have bulbs replaced by a workshop. Brake light (1) Turn signal light (2) Tail light (3) Tail light/fog light (4) 7. Install seal on bulb holder ensuring it is fitted correctly. Install bulb holder in light housing ensuring that it engages properly. Tighten four retaining screws using a screw driver. 8.
128 Vehicle care Back doors Interior lights Front and rear courtesy light 2. Turn the bulb holder anticlockwise to remove from the bulb housing. Remove the bulb by pulling. 3. Replace the bulb. 4. Insert bulb holder in bulb housing and rotate clockwise 5. Install the bulb housing ensuring it engages correctly. 1. Insert screwdriver as indicated by the arrows, press to the left and release the bulb housing. 2. Press bulb slightly towards spring clip and remove. 3. Replace the bulb. 4.
Vehicle care Front courtesy light, reading lights Removable rear courtesy light 129 2. Prise the lamp assembly out with a flat blade screwdriver at the points illustrated. 3. Renew bulb. 4. Reinstall lamp assembly. Instrument panel illumination Have bulbs replaced by a workshop. 1. Remove lens using a flat blade screwdriver. 2. Open the rear cover. 3. Renew bulbs. 4. Close rear cover. 5. Reinstall lens. 1. Press the button at the top of the lamp assembly to release it and pull down gently to remove.
130 Vehicle care Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. There are two fuse boxes in the vehicle: ■ on the right of the engine compartment, next to the battery ■ behind a cover on the lower part of the instrument panel, on the driver's side Before replacing a fuse, turn off the respective switch and the ignition. A blown fuse can be recognised by its melted wire. Do not replace the fuse until the cause of the fault has been remedied.
Vehicle care Engine compartment fuse box Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse. The fuse box is on the right of the engine compartment, next to the battery. To remove the protective cover and access the fuses, remove the two screws (see illustration).
132 Vehicle care No. Circuit Instrument panel fuse box F09 Rear door switch F10 Horn F14 High beam F15 PTCI heater F19 Air conditioning system F20 Heated rear window F21 Fuel pump F30 Fog lights F84 CNG system F85 Power outlets F86 Cigarette lighter, heated seats F87 Stop-start system F88 Mirror heating After having changed defective fuses refit the fuse box cover. If the fuse box cover is not closed correctly, malfunction may occur.
Vehicle care No. Circuit No.
134 Vehicle care Combo Tour Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage. Seek the assistance of a workshop in the event of damage or unusual wear. The tools and the vehicle jacking equipment are in the load compartment.
Vehicle care Unscrew the valve cap. Tyre pressure 3 168 and on the label on the door frame. The tyre pressure data refers to cold tyres. It applies to summer and winter tyres. Always inflate the spare tyre to the pressure specified for full load. Incorrect tyre pressures will impair safety, vehicle handling, comfort and fuel economy and will increase tyre wear. For safety reasons, it is recommended that the tread depth of the tyres on one axle should not vary by more than 2 mm.
136 Vehicle care Wheel covers Tyre chains 9 Warning 9 Warning Use of unsuitable tyres or wheel covers could lead to sudden pressure loss and thereby accidents. Tyre repair kit Minor damage to the tyre tread can be repaired with the tyre repair kit. Do not remove foreign bodies from the tyres. Tyre damage exceeding 4 mm or that is at tyre's sidewall cannot be repaired with the tyre repair kit.
Vehicle care The tyre repair kit is on the right side in the load compartment behind a cover. 1. Take the tyre repair kit from the vehicle. 2. Remove the compressor. 3. Set the compressor upright near the tyre. 4. Unscrew valve cap from defective tyre. 5. Screw the flexible filler hose onto the tyre valve. 6. The switch on the compressor must be set to J. 7. Connect the compressor plug to the power outlet or cigarette lighter socket. To avoid discharging the battery, we recommend running the engine.
138 11. 12. 13. 14. Vehicle care 5 minutes, the tyre is too badly damaged. Seek the assistance of a workshop. Do not run the compressor longer than 20 minutes. Detach the tyre repair kit. Remove any excess sealant using a cloth. Take the label indicating maximum permitted speed from the sealant bottle and affix in the driver's field of view. Continue driving immediately so that sealant is evenly distributed in the tyre. After driving approx.
Vehicle care 2. Turn the canister anticlockwise to lift it out. 3. Insert the new canister and turn it clockwise. 4. Connect the compressor air hose to the canister and fit the flexible filler tube into its allocated space. Wheel changing Some vehicles are equipped with a tyre repair kit instead of a spare wheel 3 136. Make the following preparations and observe the following information: ■ Park the vehicle on a level, firm and non-skid surface. The front wheels must be in the straight-ahead position.
140 Vehicle care 2. Attach wheel wrench securely and loosen each wheel nut by half a turn. 3. Vehicle jacking points are located at the front and rear. 4. Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping. With the jack correctly aligned, rotate until wheel is clear of the ground. 5. Unscrew the wheel nuts. 6. Change the wheel. Spare wheel 3 141. 7. Screw on the wheel nuts. 8. Lower vehicle. 9.
Vehicle care 141 Spare wheel Some vehicles are equipped with a tyre repair kit 3 136 instead of a spare wheel. The spare wheel can be classified as a temporary spare wheel depending on the size compared to the other mounted wheels and country regulations. Caution The use of a spare wheel that is smaller than the other wheels or in combination with winter tyres could affect driveability. Have the defective tyre replaced as soon as possible.
142 Vehicle care 5. Unscrew knob 2 and release cable attachment 1 from spare wheel. 6. Change the wheel. 7. Position the replaced wheel at the rear of the vehicle with the outside of the wheel facing downwards. Have the defective tyre renewed or repaired as soon as possible. CNG vehicles Vehicles with CNG; the spare wheel is located in the load compartment. 4. Withdraw spare wheel from beneath the vehicle. 8.
Vehicle care 2. Change the wheel. 3. Position the replaced spare wheel onto the bracket ensuring correct alignment of the locating pin. 4. Secure spare wheel by tightening two bolts using the wheel wrench. Have the defective tyre renewed or repaired as soon as possible. Directional tyres Fit directional tyres such that they roll in the direction of travel. The rolling direction is indicated by a symbol (e.g. an arrow) on the sidewall.
144 Vehicle care ■ A discharged battery can already freeze at a temperature of 0 °C. Defrost the frozen battery before connecting jump leads. ■ Wear eye protection and protective clothing when handling a battery. ■ Use a booster battery with the same voltage (12 Volts). Its capacity (Ah) must not be much less than that of the discharged battery. ■ Use jump leads with insulated terminals and a cross section of at least 16 mm2 (25 mm2 for diesel engines).
Vehicle care 4. Switch on electrical consumers (e.g. headlights, heated rear window) of the vehicle receiving the jump start. 5. Reverse above sequence exactly when removing leads. Towing Towing the vehicle 145 Caution The towing eye must only be used for towing and not for recovering the vehicle. Switch on ignition to release steering wheel lock and to permit operation of brake lights, horn and windscreen wiper. Transmission in neutral. Release the cap by carefully lifting with a screwdriver.
146 Vehicle care To prevent the entry of exhaust gases from the towing vehicle, switch on the air recirculation and close the windows. Seek the assistance of a workshop. After towing, unscrew the towing eye and replace the cap. Towing another vehicle The towing eye is stowed with the vehicle tools 3 133. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or even better a tow bar – to the towing eye.
Vehicle care If using a vehicle wash, comply with the vehicle wash manufacturer's instructions. The windscreen wiper and rear window wiper must be switched off. Remove antenna and external accessories such as roof racks etc. If you wash your vehicle by hand, make sure that the insides of the wheel housings are also thoroughly rinsed out. Clean edges and folds on opened doors and the bonnet as well as the areas they cover. Caution Always use a cleaning agent with a pH value of 4 to 9.
148 Vehicle care Clean rims with a pH-neutral wheel cleaner. Rims are painted and can be treated with the same agents as the body. Paintwork damage Rectify minor paintwork damage with a touch-up pen before rust forms. Have more extensive damage or rust areas repaired by a workshop. Underbody Some areas of the vehicle underbody have a PVC undercoating while other critical areas have a durable protective wax coating. After the underbody is washed, check the underbody and have it waxed if necessary.
Vehicle care Plastic and rubber parts Plastic and rubber parts can be cleaned with the same cleaner as used to clean the body. Use interior cleaner if necessary. Do not use any other agent. Avoid solvents and petrol in particular. Do not use highpressure jet cleaners.
150 Service and maintenance Service and maintenance General information ................... 150 Recommended fluids, lubricants and parts .................................... 151 General information Service information In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified.
Service and maintenance Recommended fluids, lubricants and parts Recommended fluids and lubricants Only use products that meet the recommended specifications. Damage resulting from the use of products not in line with these specifications will not be covered by the warranty. 9 Warning Operating materials are hazardous and could be poisonous. Handle with care. Pay attention to information given on the containers. Engine oil Engine oil is identified by its quality and its viscosity.
152 Service and maintenance temperatures the factory filled coolant provides frost protection down to approx. -37°C. This concentration should be maintained all year round. The use of additional coolant additives that intend to give additional corrosion protection or seal against minor leaks can cause function problems. Liability for consequences resulting from the use of additional coolant additives will be rejected. Brake and clutch fluid Only use high-performance brake fluid approved for the vehicle.
Technical data Technical data Vehicle identification .................. 153 Vehicle data ............................... 154 153 Vehicle identification Vehicle Identification Number and in the floor on the front passenger side behind a cover. Identification plate The Vehicle Identification Number is visible through the windscreen The identification plate is in the engine compartment.
154 Technical data 8 = Engine type 9-11 = Vehicle-specific or countryspecific data Information on identification label: 1 = Type approval number 2 = Vehicle Identification Number 3 = Vehicle type identification code 4 = Permissible gross vehicle weight rating in kg 5 = Permissible gross train weight in kg 6 = Maximum permissible front axle load in kg 7 = Maximum permissible rear axle load in kg The combined total of front and rear axle loads must not exceed the permissible gross vehicle weight.
Technical data Engine oil viscosity grades Engine oil viscosity grade Petrol / CNG engines Diesel engines SAE 0W-30 - ✔ SAE 0W-40 ✔ - 155
156 Technical data Engine data Sales designation 1.4 1.4 1.4 Engine identifier code 1.4i 1.4Turbo 1.4CNG Number of cylinders 4 4 4 Piston displacement [cm3] 1368 1368 1368 Engine power [kW] 70 88 88 at rpm 6000 5000 5000 Torque [Nm] 127 206 206 at rpm 4500 3000 3000 Fuel type Petrol Petrol Compressed Natural Gas/Petrol recommended 95 95 95 possible 98 98 98 possible 91 91 91 Gas – – CNG Oil consumption [l/1000 km] 0.6 0.6 0.
Technical data 157 Sales designation 1.4 1.4 1.4 Engine identifier code 1.4i 1.4Turbo 1.
158 Technical data Sales designation 1.4 1.4 1.4 Engine identifier code 1.4i 1.4Turbo 1.
Technical data Sales designation 1.3 Turbo 1.6 Turbo 2.0 Turbo Engine identifier code 1.3CDTI 1.6CDTI1) 2.0CDTI Number of cylinders 4 4 4 1248 1598 1956 Engine power [kW] 66 66 / 77 99 at rpm 4000 4000 3500 Torque [Nm] 200 2002) / 290 320 at rpm 1500 1500 1500 Fuel type Diesel Diesel Diesel Oil consumption [l/1000 km] 0.6 0.6 0.6 Piston displacement 1) 2) [cm3] Low / High output. Vehicles with manual transmission automated (MTA).
160 Technical data Performance The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle. Engine 1.4i 1.4Turbo 1.4CNG Manual transmission 100 107 107 Manual transmission automated – – – Maximum speed [mph] Engine 1.3CDTI 1.6CDTI3) 2.0CDTI 98 / 955) 102 / 984) / 955) 111 Maximum speed [mph] Manual transmission Manual transmission automated 3) 5) 4) Low / High output.
Technical data Vehicle weight Kerb weight, basic model - Van Length Roof height Engine Gross vehicle weight Kerb weight L1 H1 1.4i 1990 / 2160 1240 / 1260 1.4Turbo – / 2325 – / 1400 1.4Turbo CNG 2430 / – 1450 / – 1.3CDTI 2020 / 2290 1270 / 1290 1.6CDTI 2060 / 2330 1310 / 1330 2.0CDTI 2100 / 2370 1350 / 1370 1.4i 2010 / 2180 1260 / 1280 1.4Turbo – / 2345 – / 1420 1.4Turbo CNG 2420 / – 1470 / – 1.6CDTI 2080 / 2350 1330 / 1350 2.
162 Technical data Length Roof height Engine Gross vehicle weight Kerb weight L2 H1 1.4i 2200 / – 1300 / – 1.4Turbo 2365 / – 1440 / – 1.4Turbo CNG 2470 / 2450 1490 / 1540 1.3CDTI 2330 / – 1330 / – 1.6CDTI 2370 / – 1370 / – 2.0CDTI 2410 / – 1410 / – 1.4Turbo 2455 1455 1.6CDTI 2460 1460 2.
Technical data Kerb weight, basic model - Combi Length Roof height Engine Gross vehicle weight Kerb weight L1 H1 1.4i 2060 1350 1.4Turbo 2225 1500 1.3CDTI 2090 1380 1.6CDTI 2130 1420 2.0CDTI 2170 1460 1.4i 2160 1360 1.3CDTI 2190 1390 1.6CDTI 2230 1430 2.0CDTI 2270 1470 1.4i 2200 1400 1.4Turbo 2265 1540 1.3CDTI 2230 1430 1.6CDTI 2270 1470 2.0CDTI 2310 1510 2.
164 Technical data Kerb weight, basic model - Combo Tour Length Roof height Engine Gross vehicle weight Kerb weight L1 H1 1.4i 1940 1340 1.4Turbo 2030 1490 1.4Turbo CNG 2110 1540 1.3CDTI 1970 1370 1.6CDTI 2010 1410 2.0CDTI 2050 1450 1.4i 2210 1430 1.6CDTI 2400 1500 2.0CDTI 2440 1540 1.4i 2055 1370 1.4Turbo 2135 1490 1.3CDTI 2085 1400 1.6CDTI 2115 1430 2.0CDTI 2165 1480 2.
Technical data 165 Vehicle dimensions Type Van Wheelbase Short Long Short Long Short Long Length [mm] 4390 4740 4390 4740 4390 4740 Width without exterior mirrors [mm] 1832 1832 1832 1832 1832 1832 Width with exterior mirrors [mm] Combi 2119 Height (without antenna) [mm] Standard roof 1845 / High roof 2100 2119 18956) 1880 / Combo Tour 2119 19277) 1845 / 2119 18956) 1880 / 2119 19277) 1845 / 2119 18956) 1880 / 19277) – 2100 – 2100 – Length of load compartment f
166 Technical data Type Van Combi Combo Tour Wheelbase [mm] 2755 3105 2755 3105 2755 3105 Turning circle kerb to kerb [m] 11.2 12.5 11.2 12.5 11.2 12.
Technical data Capacities Engine oil Engine 1.4i 1.4Turbo 1.4CNG 1.3CDTI 1.6CDTI 2.0CDTI including Filter [l] 2.7 2.9 2.7 3.2 4.9 4.9 between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0 1.0 Fuel tank Petrol/diesel, nominal capacity [l] 60 Natural gas CNG, nominal capacity [kg] Petrol, nominal capacity [l] 16.15 kg8) / 22.1 kg9) 22 8) 9) Short wheelbase version. Long wheelbase version.
168 Technical data Tyre pressures Van Comfort with up to 2 people and 100 kg luggage With full load front rear front [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 185/65 R15 88T 250/2.5 (36) 250/2.5 (36) 290/2.9 (42) 290/2.9 (42) 185/65 R15 92T 250/2.5 (36) 260/2.6 (38) 290/2.9 (42) 300/3.0 (44) 195/65 R15 95T 240/2.4 (35) 240/2.4 (35) 260/2.6 (38) 270/2.7 (39) 195/60 R16 C 99/97T 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 330/3.3 (48) 360/3.
Technical data Combi Engine All Comfort with up to 3 people With full load front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 185/65 R15 88T 250/2.5 (36) 250/2.5 (36) 290/2.9 (42) 290/2.9 (42) 185/65 R15 92T 250/2.5 (36) 260/2.6 (38) 290/2.9 (42) 300/3.0 (44) 195/65 R15 95T 240/2.4 (35) 300/3.0 (44) 260/2.6 (38) 320/3.2 (46) 195/60 R16 C 99/97T 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 360/3.
170 Technical data Combo Tour Engine All Comfort with up to 3 people With full load front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 185/65 R15 88T 250/2.5 (36) 250/2.5 (36) 290/2.9 (42) 290/2.9 (42) 185/65 R15 92T 250/2.5 (36) 260/2.6 (38) 290/2.9 (42) 300/3.0 (44) 195/65 R15 95T 240/2.4 (35) 240/2.4 (35) 260/2.6 (38) 260/2.6 (38) 195/60 R16 C 99/97T 270/2.7 (39) 270/2.7 (39) 270/2.7 (39) 280/2.8 (41) 12) 360/3.
Customer information Customer information Vehicle data recording and privacy ....................................... 171 Vehicle data recording and privacy Event data recorders Data storage modules in the vehicle A large number of electronic components of your vehicle contain data storage modules temporarily or permanently storing technical data about the condition of the vehicle, events and errors.
172 Customer information When using the vehicle, situations may occur in which technical data related to other information (accident report, damages on the vehicle, witness statements etc.) may be associated with a specific person possibly, with the assistance of an expert. Additional functions contractually agreed upon with the client (e.g. vehicle location in emergency cases) allow the transmission of particular vehicle data from the vehicle.
Customer information 173
174 Index A Accessories and vehicle modifications .......................... 117 Adjustable air vents ..................... 91 Airbag activation........................... 73 Airbag and belt tensioners ........... 67 Airbag deactivation .......... 41, 68, 73 Airbag system .............................. 39 Air conditioning regular operation 93 Air conditioning system ................ 89 Air intake ...................................... 92 Air vents........................................ 91 Alert.........
175 Control of the vehicle ................... 94 Controls........................................ 56 Convex shape .............................. 26 Coolant and antifreeze............... 151 Cruise control ...................... 73, 107 Cupholders .................................. 49 D Danger, Warnings and Cautions . . . 3 Date.............................................. 73 Daytime running lights............ 73, 83 Diesel particle filter................. 71, 98 Distance to next service...............
176 Hill start assist...................... 69, 105 Horn ....................................... 13, 57 I Identification plate ..................... 153 Ignition switch positions ............... 95 Immobiliser ............................ 25, 72 Indicators...................................... 62 Information displays...................... 73 Instrument panel fuse box ......... 132 Instrument panel illumination ..... 129 Instrument panel illumination control ......................................
177 Rear fog light ............................... 73 Rear fog lights ............................. 85 Rear parcel shelf.......................... 50 Rear windows .............................. 29 Rear window wiper/washer .......... 58 Recommended fluids and lubricants ........................ 151, 154 Refuelling ................................... 112 Reversing lights ........................... 85 Ride control systems.................. 106 Roof load...................................... 54 Roof rack .....
178 Vehicle shutdown................... 79, 95 Vehicle specific data ...................... 3 Vehicle storage........................... 117 Vehicle tools............................... 133 Vehicle unlocking ........................... 6 Vehicle weight ........................... 161 Ventilation..................................... 88 Volume......................................... 73 W Warning chime.............................. 73 Warning chimes ........................... 79 Warning lights.............
