Owner’s Manual SIGNUM Operation, Safety and Maintenance Reproduction or translation, in whole or in parts, is not permitted without prior written consent from Vauxhall Motors Ltd. All rights as understood under the copyright laws are explicitly reserved by Vauxhall Motors Ltd. All information, illustrations and specifications contained in this manual are based on the latest production information available at the time of publication. The right is reserved to make changes at any time without notice.
VAUXHALL Signum Operation, Safety, Maintenance
Data specific to your vehicle Please enter your vehicle’s data here to keep it easily accessible. This information is available under the section "Technical data" as well as on the identification plate and in the Service Booklet.
Your Signum is an intelligent combination of forwardlooking technology, impressive safety, environmental friendliness and economy. It now lies with you to drive your vehicle safely and ensure that it performs perfectly. This Owner’s Manual provides you with all the necessary information to that end. Make sure your passengers are aware of the possible risk of accident and injury which may result from improper use of the vehicle.
Contents Commitment to customer satisfaction: Our aim: to keep you happy with your vehicle. All Vauxhall Authorised Repairers offer first-class service at competitive prices. Experienced, factory-trained technicians work according to factory instructions. Your Authorised Repairer can supply you with GENUINE VAUXHALLAPPROVED PARTS, which have undergone stringent quality and precision checks, and of course useful and attractive VAUXHALL-APPROVED ACCESSORIES.
2 In brief In brief To unlock and open vehicle: Press button q, pull door handle 6 Door locks, child safety locks – see page 37, keys – see page 26, electronic immobiliser – see page 27, remote control – see page 28, central locking – see page 30, anti-theft locking system 3 – see page 30, Vauxhall alarm system 3 – see page 35.
In brief To adjust front seats: Pull handle, slide seat, release handle To adjust front seat backrests: Turn handwheel 6 Seats – see page 48, seat position – see page 50, electrically adjustable front seats – see page 50, adjusting rear seats – see page 56. Do not lean on seat backrest whilst adjusting it. 9 Warning Important: Do not sit nearer than 10 inches (25 cm) from the steering wheel, to permit safe airbag deployment. Move backrest to suit seating position.
4 In brief Adjusting front seat inclination 3: Operate front lever on outboard side of seat Electric seat adjustment 3: Operate switch on outboard side of seat Pump action of lever Upwards: Seat steeper Downwards: Seat flatter 1 2 3 4 5 6 Seats – see page 48, seat position – see page 50, electrically adjustable front seats – see page 50.
In brief To adjust head restraint angle of front and outboard rear seats 3: Swivel bottom edge of head restraint forward or rearward 6 Head restraints – see page 53, head restraint position – see page 54, rear head restraints – see page 54. To put on seat belt: Pull out seat belt without jerking it, pass it over the shoulder and click into the belt buckle The seat belt must not be twisted at any point. The lap belt must lie snugly against the body.
6 In brief To adjust exterior mirrors: Four-way switch in driver’s door If the outer mirror switch is pressed 1 the four-way switch operates the driver and front passenger mirrors 3, and if the inner mirror switch is pressed 2 it only operates the front passenger mirror. 6 Mirrors – see page 40, aspherical exterior mirrors 3 – see page 40, automatic anti-dazzle exterior mirrors – see page 41, heated exterior mirrors – see page 13, electric seat adjustment 3 – see page 50.
In brief Turn light switch: 7 = Off 8 = Parking lights 9 = Dipped or main beam AUTO = Automatic dipped beam activation 3 Push button: > = Fog lights 3 r = Fog tail light 6 Lighting – see page 128, headlight control indicator – see pages 16, 126. Headlight flash, main beam and dipped beam: Headlight flash = Pull stalk towards steering wheel Main beam = Stalk forwards Dipped beam = Lever forward again or toward steering wheel 6 Main beam, headlight flash – see page 129.
8 In brief
In brief 1 Page Side air vents .................................. 142 2 Front passenger airbag .................. 81 3 Centre air vents ............................. 142 4 Infotainment system 3 ................. 137 5 Central information display for time, date, outside temperature Infotainment System 3, Check-Control 3, Trip computer 3, Automatic air conditioning 3 ...... 108 6 Turn signal lights................................. 7 Headlight flash, Dipped beam, main beam ................
10 In brief Control indicators O Turn signal lights, see pages 7, 98. I Engine oil pressure, see page 98. R Brake system, clutch system, see pages 99, 208, 272. p Alternator, see page 99. v Airbag systems, belt tensioners, see pages 72, 81. W Coolant temperature, see pages 100, 106. 8 Exterior lights, see pages 100, 128. 1 Sport program of automatic transmission 3, see pages 171, 178. T Winter program of automatic transmission 3 or Easytronic 3, see pages 172, 180.
In brief Hazard warning lights: On = Press ¨ Off = Press ¨ again 6 Hazard warning lights – page 131. To operate horn: Press j in middle of steering wheel 6 Airbag systems 3 – see page 81, remote control from steering wheel 3 – see page 137. 11 Windscreen wiper: Gently tap lever upwards § = Off $ = Adjustable timed interval wipe % = Slow & = Fast Press the stalk down from position §: Single swipe.
12 In brief Automatic wiping with rain sensor 3: Gently tap stalk upwards $ = Automatic wiping with rain sensor § = Off Automatic wiping $: Low sensitivity: To the left High sensitivity: To the right 6 Windscreen wiper – see page 126, wiper blades – see pages 273, 274, car care – see page 260. Operating windscreen and headlight wash systems 3: Pull stalk towards steering wheel 6 Windscreen wash system and headlight wash system – see page 127, further notes – see pages 260, 273.
In brief Heated rear window, heated exterior mirrors: On = Press Ü Off = Press Ü again 6 Air conditioning – see page 140, heated rear window – see page 143.
14 In brief Manual transmission: Reverse gear: with vehicle stationary, pull the ring up three seconds after de-clutching and engage gear. If the gear does not engage, set the lever in neutral, release the clutch pedal and depress again; then repeat gear selection.
In brief In order to leave P switch on ignition, operate foot brake and press button on selector lever. Before starting off, check: To engage P or R, push button on selector lever. z Engine oil level and fluid levels in engine compartment – see pages 267 to 275. P z All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and operational.
16 In brief Parking the vehicle z Always apply the handbrake firmly without actuating the release knob; to do this fold up the armrest 3. Apply as fully as possible on an uphill or downhill incline. To reduce the amount of force required to activate the brake, depress the foot brake at the same time. Releasing the hand brake: Raise lever slightly, press release button, lower lever fully 6 Handbrake – see page 209. z Switch off the engine - to do this, turn the ignition key to 0.
In brief 17 That was a brief overview of the most important information for your first trip in your vehicle. The other pages of this chapter contain a summary of the interesting functions in your vehicle. The remaining chapters of the Owner’s Manual contain important information on operation, safety and maintenance as well as a complete index.
18 In brief Airbag System The airbag system consists of several separate systems. Front airbag system The front airbag system will be triggered in the event of a serious accident involving a frontal impact and forms safety cushions for the driver and front passenger. The forward movement of the driver and front passenger is checked and the risk of injuries to the upper body and head thereby substantially reduced.
In brief 19 Active head restraints 3 at front seats Operating menus in the information display 3 Selection using multifunction button: rotate and press multifunction button. In the event of a rear-end impact, the active head restraints tilt forward a little. The head is more effectively supported by the head restraint and the danger of injuries caused by whiplash in the area of the neck is reduced.
20 In brief Ü Board Computer BC 1 BC 2 Timer 1 Tyres 8 Selection using left-hand adjuster wheel on steering wheel: rotate and press adjuster wheel. 6 Info Display – see page 108. 19,5° 19:36 All values 257.0 Ø 40 Ø 11.0 7.0 miles Coolant level mph check gals miles/gal OK Trip computer 3 Check control 3 The trip computers provide information on driving data, which is continually recorded and evaluated electronically.
In brief Remote control on steering wheel 3 The functions of the infotainment system 3 and the information display can be operated with the buttons and adjuster wheels on the steering wheel. Further information is available in the infotainment system operating instructions. 6 Remote control on steering wheel 3 – see page 137, Infotainment system – see pages 108, 137.
22 In brief Rear seats To adjust or fold outboard seat backrest Folding the centre seat cushion To adjust outboard seats z When folding the seat, guide the seat belt through the side retainer. z Pull handle beneath seat. z Pull handle on outboard side of seat. z Fold the seat rearward 180° until the cushion points down. z Pull handle beneath seat. z Slide seat forward or rearward. z Release handle and audibly engage seat in position.
In brief 23 Curve lighting The Xenon light beam pivots based on steering wheel position and speed (from approx. 6 mph /10 km/h). The headlights shine at an angle of up to 15° to the right or left of the direction of travel. Turn lighting An additional light comes on at certain steering wheel settings (after approx. 90°), turn signal settings and speeds (up to approx. 25 mph / 40 km/h).
24 In brief Damping and steering 3 become more direct and provide better contact with the road surface. The engine reacts more quickly to accelerator movements. With automatic transmission 3, the shift times are reduced and gear changes occur at higher engine speeds (not when cruise control 3 is active). 6 Sport mode 3 – see page 198. SPORT mode 3 To activate Press the SPORT button. The LED in the button illuminates.
In brief Diesel particle filter 3 The diesel particle filter system removes polluting soot particles out of the engine exhaust gases. The system includes a self-cleaning function that operates automatically while driving. The filter is cleaned by burning the trapped soot particles at a high temperature. There may be an increase in fuel consumption, exhaust smell, and engine cooling fan operation 3 during the self-cleaning operation.
26 Keys, doors, windows, sun roof Keys, doors, windows, sun roof Replacement keys ............................... Car Pass 3............................................ Key with foldaway key section 3 ....... Electronic immobiliser.......................... Store and activate personal vehicle settings using the remote control .... Remote control .................................... Central locking system ........................ Fault when locking or unlocking......... Luggage compartment.................
Keys, doors, windows, sun roof 27 If control indicator A illuminates after the engine is started, there is a fault in the engine electronics or transmission electronics 3 (see pages 174, 182, 192) or there is water in the diesel fuel filter 3, see page 270. Note The immobiliser does not lock the doors. Therefore, after leaving the vehicle always lock it and switch on the Vauxhall alarm system 3 – see pages 30, 35.
28 Keys, doors, windows, sun roof Store and activate personal vehicle settings using the remote control The remote control has a range of approx. 5 metres. This range can be affected by outside influences. Aim the remote control at the vehicle to operate. The last settings selected for z the instrument illumination, Handle the remote control with care, protect it from moisture and high temperatures and avoid unnecessary operation.
Keys, doors, windows, sun roof Fault If the central locking system cannot be operated with the remote control, it may be due to the following: Make sure that you dispose of old batteries in accordance with environmental protection regulations. Remote control synchronisation After a battery change, unlock door with key in lock, see page 33. Inserting the key into the lock synchronises the remote control. z The range of the remote control has been exceeded. z Remote control battery voltage is too low.
30 Keys, doors, windows, sun roof Central locking system For doors, boot lid/tailgate and tank flap. To unlock Press button q on remote control. To lock Press button p on remote control. Mechanical anti-theft locking system 3 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from inside. All doors must be closed. Press button p on remote control again no more than 15 seconds after locking.
Keys, doors, windows, sun roof Automatic locking 3 The central locking can be set to lock automatically at a certain speed. Programming unlocking mode When the vehicle is delivered from the factory, the remote control is preset so that a single press of the q button opens all of the doors and the luggage compartment. The unit can be configured so that a single press of the q button unlocks the entire vehicle or just the driver’s door.
32 Keys, doors, windows, sun roof Note z If the driver’s door is not closed properly, the central locking system will unlock again immediately after locking. In vehicles with electronic windows, the windows can be closed from outside: hold down button p on the remote control until all windows are closed. z 30 seconds after unlocking using the remote control the doors automatically lock again 3 if neither a door nor the luggage compartment has been opened.
Keys, doors, windows, sun roof Automatic closing 3 If the mechanical anti-theft locking system 3 is activated, the electronic windows and sun roof 3 are automatically closed and the electrically retractable exterior mirrors 3 are automatically retracted as soon as the rain sensor 3 detects water on the windscreen.
34 Keys, doors, windows, sun roof Luggage compartment To unlock Press button q on remote control. To open The luggage compartment can be opened by pulling the catch beneath the handle. Illumination of s indicates the the luggage compartment is open. Pay attention to instructions concerning open tailgate, see page 35. To close There is a handle on the inside of the tailgate for closing the luggage compartment.
Keys, doors, windows, sun roof 35 Vauxhall alarm system 3 Monitors z the doors, luggage compartment, bonnet, z the passenger compartment, z vehicle tilt, e.g. if it is raised, z the ignition. 9 Warning To lock Press button p on the remote control – or – central locking switch m in driver’s door press when doors are closed. Open tailgate 9 Warning Do not drive with the luggage compartment open, e.g. when transporting bulky objects, since toxic exhaust gas could penetrate the interior.
36 Keys, doors, windows, sun roof After the first 10 seconds of the Vauxhall alarm system activation: z LED flashes = System switched on slowly z LED comes = Switch-off function on for approx. 1 second If a system fault occurs, contact a workshop for assistance. Activation without monitoring of passenger compartment and vehicle tilt Activate e.g. when animals are left in the vehicle. 1. Close tailgate and bonnet. 2. Press button Ä, LED in button flashes (maximum of 10 seconds), see next column. 3.
Keys, doors, windows, sun roof 37 Note z Changes to the vehicle interior, such as the use of seat covers, could impair the function of passenger compartment monitoring. z Disable interior monitoring if the interior of the vehicle switched off is being heated. Alarm An alarm can be triggered whilst the Vauxhall alarm system is active: z an acoustic signal (horn) and z a visual signal (hazard warning lights). To deactivate Press button q of the remote control – or – turn on the ignition.
38 Keys, doors, windows, sun roof The programmed universal remote control can replace the individual remote control units of the systems to be operated. Three buttons on the underside of the mirror housing can be used to operate various systems. Consult your Vauxhall Authorised Repairer for details on compatible systems. 9 Warning Universal remote control in mirror housing 3 to operate up to 3 different remotely operated systems (e.g. garage door, domestic alarm system, domestic exterior lighting).
Keys, doors, windows, sun roof Programming the universal radio control system for variable code systems 1. Perform basic programming – see previous page. 2. Activate synchronisation mode of system (see system manufacturer’s system operating manual) and briefly press the pre-programmed button on the universal remote control three times within 30 seconds. 3. The radio control system is now programmed for variable code systems.
40 Keys, doors, windows, sun roof Exterior mirrors Adjusting exterior mirrors 3 Adjustment using the four-way switch in the driver’s door: If the outer mirror switch 1 is pressed, the four-way switch operates the driver and passenger mirrors 3, if the inner mirror switch 2 is pressed, it only operates the passenger mirror. The glass of the mirror is adjusted in the relevant direction in accordance with the operation of the four-way switch.
Keys, doors, windows, sun roof 41 Automatic anti-dazzle exterior mirrors 3 on the driver’s side Dazzle from following vehicles at night is automatically reduced. The mirror does not reduce dazzle when: z the ignition is switched off, z reverse gear is engaged or selector lever set to R, z the interior lights are on, z a door is open. Interior mirror To adjust, swivel mirror housing. Swivel lever on underside of mirror housing to reduce dazzle from following vehicles at night.
42 Keys, doors, windows, sun roof Electric windows 9 Warning Take care when operating the electronic windows. Risk of injury, especially for children. Vehicle occupants should be informed accordingly. If there are children on the rear seat, switch on the child safety system 3 for the electric windows. Keep a close watch on the windows when closing them. Ensure that nothing becomes trapped in them as they move.
Keys, doors, windows, sun roof 43 Safety function If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and the window opened again. If the windows do not move easily (e.g. on account of frost), keep pressing the switch for the window in question until the window has been closed in stages.
44 Keys, doors, windows, sun roof Automatic closing 3 see page 33. Overload If the windows are repeatedly operated at short intervals, the power supply is briefly cut off. The system is protected by fuses in the fuse box – see page 243. Fault If the windows cannot be opened and closed automatically, activate the window electronics as follows: 1. Close doors. 2. Switch on ignition. 3. Window completely open. 4. Close window and press on button for at least 3 seconds. 5. Repeat for each window.
Keys, doors, windows, sun roof Sun roof 3 To raise Turn the rotary switch to any position between d and e. The sun roof will automatically move to the desired position. When the switch is in position e, the sun roof is fully raised. 9 Warning Caution when operating the sun roof. Risk of injury, particularly to children. Vehicle passengers should be informed accordingly. To lower Turn rotary switch to d. Keep a close watch on the sliding roof when closing it.
46 Keys, doors, windows, sun roof Automatic closing 3 see page 33. Safety function If the sun roof encounters resistance during automatic closing, it is immediately stopped and opened again, as long as the vehicle is stationary. Sun shade To reduce the sunlight in the interior with the sliding roof closed or raised. 9 Warning Open or close sun shade as required. When the sun roof is opened, the sun shade is also opened.
Keys, doors, windows, sun roof Overload If the system is overloaded, the power supply is automatically cut off for a short time. 3. Turn rotary switch to ü and keep it depressed until the sun roof is open. Fault If the sun roof no longer assumes the desired position automatically, program sun roof electronics as follows: 5. Turn rotary switch to e and leave there until the sun roof is fully raised. 1. Switch on ignition. 47 4. Turn rotary switch to d and keep it depressed until the sun roof is closed.
48 Seats, interior Seats, interior Manually adjustable front seats ........ Electrically adjustable front seats 3 .. Head restraints .................................... Armrest 3 between the front seats .... Armrest between rear seats ............... Rear seats............................................. Travel Assistant 3 ............................... Luggage compartment extension ..... Luggage compartment cover ............ Safety net 3 ......................................... Lashing eyes ........
Seats, interior Adjusting the seat height 3 To adjust height of seat, operate lever on outboard rear side of seat. Pump action of lever Upwards: Seat higher Downwards: Seat lower To adjust seat incline 3 Pump action of lever Upwards: Seat steeper Downwards: Seat flatter 49 Adjusting the lumbar support 3 To adjust, activate the lever on the backrest, relieving pressure on the backrest as you do so. Adjust lumbar support to suit personal requirements.
50 Seats, interior Electrically adjustable front seats 3 9 Warning Care must be taken when operating the electrically adjustable seats. There is a risk of injury, particularly for children, and a danger that articles could become trapped. Keep a close watch on the seats when adjusting them. To adjust thigh support 3 on the sports seats 3 To adjust, press button in recessed grip located in the centre beneath the adjusting cushion and move the thigh support.
Seats, interior Adjusting the longitudinal position Move switch 1 forwards/backwards. Height adjustment Move switch 1 upwards/downwards at rear Seat backrest adjustment Turn switch 2 forwards/backwards. Operate switch until desired seat position is reached. Seat position – see page 51. After adjusting the seat, adjust height of seat belt – see page 75. Electrically operated lumbar support 3 on driver’s seat Adjust lumbar support using four-way switch on outboard side of driver’s seat.
52 Seats, interior Readiness for operation z with ignition on, z within 10 minutes of switching ignition off, z within 10 minutes of opening or closing the driver’s door, z within 10 minutes of inserting or removing the ignition key. Readiness for operation stops when the vehicle is locked. Memory function 3 for electrically adjustable driver’s seat and exterior mirrors Three different seat and mirror settings can be stored (e.g. for three drivers). Storing settings 1. adjust seat, 2.
Seats, interior Retrieving settings Keep position keys 1, 2 or 3 pressed until the stored seat and mirror positions have been reached. For reasons of safety, seat adjustment stops immediately if the position button is released or one of the setting buttons is operated. Adjustments may only be performed with vehicle stationary.
54 Seats, interior To adjust the incline, swivel the bottom edge of the head restraint forward or rearward Adjusting the rear, centre head restraint 3 To adjust head restraints, pull forwards with both hands and slide up or down. To improve visibility if the middle seat is unoccupied or to increase the size of the luggage compartment, push headrest down as far as possible. If seat is occupied, pull head restraint upwards. Head restraint position The middle of the head restraint should be at eye level.
Seats, interior Active head restraints 3 In the event of a rear-end impact, the active head restraints tilt slightly forwards. The head is more effectively supported by the head restraint and the danger of whiplash in the area of the neck. Active head restraints are identified by the lettering ACTIVE on the head restraint guide sleeves. Removing the head restraints Press and release the two catches. Pull and remove the head restraint.
56 Seats, interior The armrest contains a stowage compartment: to open, slide armrest back, press button at front and lift. Armrest between rear seats Rear seats The armrest can be folded down. Move seat Pull handle beneath seat and slide seat forward or backward. Release handle and allow seat to audibly latch. If the rear centre seat is being used or the rear seats are being folded down, fold armrest upward.
Seats, interior Adjusting backrest Pull handle at outboard side of seat and move backrest forward or backward. Release handle and allow seat to audibly latch. Centre rear seat 9 Warning The centre rear seat may only be occupied by persons between 1.50 metres and 1.75 metres tall. When this seat is in use, both outboard seats must be slid all the way back with their backrests flush with the centre seat backrest. Child restraint systems are not to be mounted on the centre rear seat.
58 Seats, interior Travel Assistant 3 The Travel Assistant Contains z z z z z z Armrest Stowage compartments Waste container Drink holders Accessory sockets. Connection console e.g. for DVD player 3 z Electric cool box z Tables z Twin Audio (rear audio module) 3 or stowage compartment. The Travel Assistant and the connecting console are installed above the folded-over centre seat cushion. Installing the Travel Assistant The centre seat cushion must face down.
Seats, interior Swivel the locking lever downwards. Check the locking position of the Travel Assistant: The red mark (see Fig. 17566 J) must not be visible. Otherwise, lock using the key – see page 63, Fig. 17575 J. Remove cap 3 from plug at securing bracket. To lock, insert Travel Assistant into recesses in connecting console and slide back as far as possible. 59 If it is correctly locked, the red mark must no longer be visible in the window, otherwise the procedure must be repeated.
60 Seats, interior Drink holder and accessory sockets Open the drink holder by pressing the marking. Only accessories with maximum power consumption of 120 Watts must be connected to the accessory sockets. For notes – see page 94. Stowage compartments The lower stowage compartment is opened by pressing the mark. The underside of the compartment has an opening through which objects in the compartment can be raised. The upper stowage compartment is located under the armrest.
Seats, interior Swivel up the display holder, slide DVD player display into bracket from below and fix in position with bracket. Maximum load: 1 kg. Electric cool box To open, fold open the armrest together with the stowage compartment. Switch on the cool box as needed.
62 Seats, interior Set required clearance by adjusting longitudinal position of table (4). Swivel armrest down. Tables Fold armrest upward (1). Use recessed grip to pull table upwards as far as it will go (1), swivel table forward (2) and fold downwards (3).
Seats, interior To fold away the table, swivel the armrest up. Push the table forward as far as it will go (1). Fold the table upwards passed the resistance point (2), swivel it rearwards and insert in the Travel Assistant (3). Swivel armrest down. 63 Dismantling the Travel Assistant Open catch using key, red mark appears in window.
64 Seats, interior Pull the Travel Assistant to the front on the connecting console and remove. Fit cap 3 to plug on securing bracket. Press the locking lever down, press the button on the front of the connecting console and swivel the locking lever upwards. Swivel connecting console upward and pull out of recesses.
Seats, interior 65 Luggage compartment extension The maximum amount of luggage space is obtained by folding down the centre seat and the two outboard seats and the passenger seat backrest 3 and removing the luggage compartment cover, see following description. 9 Warning The load must not obstruct operation of the pedals, handbrake and gearshift, or the freedom of movement of the driver. Do not leave unsecured objects in the interior. Note instruction on page 70.
66 Seats, interior Fold down outboard rear seat backrests. Remove luggage compartment cover if necessary – see page 67. Push rear head restraint down as far as possible – see page 54. Slide rear seat back. Fold down centre backrest Fold middle rear seat cushion, see left column. Slide down middle head restraint – see page 54. Pull the strap located on the back of the centre seat backrest and fold the backrest. The outer seats can continue to be used. To move upright, pull loop and audibly engage backrest.
Seats, interior To move the rear seat backrest upright, pull handle on outboard side, move rear seat backrest upright and audibly latch. Folding down the front passenger seat 3 Push head restraint on front passenger’s seat down as far as it will go. Slide front passenger seat backwards. Fold front passenger seat forward by raising release lever. To restore, press the release lever forward, restore the front seat backrest to an upright position and audibly engage. Notes on loading see page 70.
68 Seats, interior Safety net 3 The safety net is installed behind the front seats. Passengers must not be carried behind the safety net. Removing Open luggage compartment cover. Raise the release lever on the right of the luggage compartment cover. Remove cover from the brackets by lifting first on the right, then on the left.
Seats, interior Hook belts into lashing eyes 3 in floor behind front seats and tension. Removing Unhook belts from lashing eyes in floor. Unhook rods from brackets in roof frame. Press retaining knobs on joints and collapse rods. Roll up net and stow in attached bag. 69 Lashing eyes In the luggage compartment, secure items being transported against slipping by attaching lashing straps 3 or a luggage net 3.
70 Seats, interior z Fit safety net 3 when transporting articles in luggage compartment – see page 68. z Objects must not be stored in the airbag inflation area, because they could cause injury if the airbag inflates. z Loose objects in the luggage compartment should be secured against slipping using a luggage net 3 – see page 69. z The load must not obstruct the operation of the pedals, the handbrake or the gears or restrict the driver’s freedom of movement. Do not place loose objects in the interior.
Seats, interior Three-stage safety system Comprising: z three-point seat belts, z belt tensioners at the front seats and the rear outer seats, z airbag systems for driver, front passenger and outboard rear seats 3. The three stages are activated in sequence depending on the severity of the accident: z The automatic seat belt locking devices prevent the belt strap from being pulled out and thus ensure that the vehicle occupants are retained in their seats.
72 Seats, interior 9 Warning Always wear your seat belt, and that means also in urban traffic and when you are a rear seat passenger. It can save your life! Pregnant women must always wear a seat belt – see page 75. In the event of an accident, persons not wearing seat belts endanger their fellow occupants and themselves. Control indicator X for the seat belt – see page 101. Seat belts are only intended for one person. They are not suitable for anyone under 12 years of age or under 150 cm tall.
Seats, interior Actuation of belt tensioners is indicated by illumination of control indicator v, see next page. 73 9 Warning Have the cause of the fault eliminated immediately by a workshop. If the belt tensioners are triggered, they must be replaced by a workshop. The system’s integrated self-diagnostics allows faults to be quickly remedied. Important information – see page 72.
74 Seats, interior Important z Do not fit accessories not specifically released for your vehicle type or store objects in the belt tensioner operating area (in the area of the belt buckles) due to the risk of injury in the event the belt tensioners are triggered. z Do not make any modifications to the components of the belt tensioners, as this will render the vehicle unroadworthy. 9 Warning Incorrect handling (e.g.
Seats, interior Operating the seat belts Fitting seat belts Pull the seat belt out of the retractor and place it across the body, making sure it is not twisted. Insert the latch plate into the buckle. The front seat backrest must not be tilted back too far or the seat belt will not operate properly. The recommended angle of inclination is 25°. Make sure that the lap belt is not twisted and that it fits snugly across the body.
76 Seats, interior Adjust height such that the belt passes over the wearer’s shoulder and rests against the shoulder. It must not pass over the neck or upper arm. Removing the belt To release belt, press red button on belt buckle; the seat belt retracts by itself. Three-point seat belt on centre rear seat Slide open cover in roof and remove seat belt latch plates from roof.
Seats, interior To release belt, press button on belt buckle (2). If the centre seat is folded, press button on belt buckle (1). The seat belt retracts by itself. Engage upper latch plate in bracket and attach lower latch plate to magnetic bracket on roof. Push cover shut. Engage lower latch plate into left-hand buckle (1) of the centre seat. Guide the seat belt by the upper latch plate over the shoulder and abdomen (avoid twisting) and engage in right-hand buckle (2) of the centre seat.
78 Seats, interior Permissible options for fitting a child safety seat1) Weight and age class2) On front passenger seat On outboard rear seats Group 0: up to 10 kg or approx. 10 months B 1, + U, + On centre rear seat X Group 0+: up to 13 kg or approx. 2 years Group I: 9 to 18 kg or approx. 8 months to 4 years Group II: 15 to 25 kg or approx. 3 to 7 years Group III: 22 to 36 kg or approx.
Seats, interior U = Can be used universally in combination with a three-point seat belt. + = Vehicle seat available with ISOFIX fixings. When using ISOFIX, only ISOFIX child restraint systems approved for the vehicle may be used. X = No child restraint system permitted in this weight class. Note z Children under 12 years or under 150 cm tall should only travel in an appropriate child safety system. z When transporting children, use the child restraint systems suitable for the child’s weight.
80 Seats, interior Airbag System The airbag system consists of several separate systems. Front airbag system The front airbag system will be triggered in the event of a serious accident involving a frontal impact and forms safety cushions for the driver and front passenger. The forward movement of the driver and front passenger is checked and the risk of injuries to the upper body and head thereby substantially reduced.
Seats, interior 81 Exception: Passenger seat with seat occupancy recognition system 3. The seat occupancy recognition system deactivates the front and side airbags 3 on the front passenger side if the front passenger seat is unoccupied or a Vauxhall child restraint system with transponders 3 has been fitted to the front passenger seat. Seat occupancy recognition, see page 87. Vauxhall child restraint system with transponders 3, see page 77.
82 Seats, interior When triggered, the front airbags inflate in milliseconds to form a safety cushion for the driver and front passenger. The forward movement of the front seat occupants is checked, thereby substantially reducing the risk of injury to the upper body and head. No impairment of view will occur, because the airbags inflate and deflate so quickly that it is often not even noticed in an accident.
Seats, interior 83 9 Warning Seat belts must therefore always be worn. The front airbag system serves to supplement the three-point seat belts. If you do not wear your seat belt you risk being seriously injured, or even thrown from the vehicle, in the event of an accident. In the event of an accident the seat belt helps to keep you in the correct seating position, so that the front airbag system can provide you with effective protection.
84 Seats, interior 9 Warning There must be no objects in the area in which the airbag inflates or in the area between the seat backrests and the vehicle body. Do not place the hands or arms on the covers of the airbag systems. Important information – see page 89. The three-point seat belt must always be correctly fitted – see page 71. When triggered, the side airbag inflates within milliseconds to form a safety cushion for the driver or front passenger in the respective door area.
Seats, interior Curtain airbag 3 The curtain airbag system is identified by the word AIRBAG on the roof pillar trim.
86 Seats, interior 9 Warning 9 Warning There must be no objects in the area in which the airbag inflates. Do not place the hands or arms on the covers of the airbag systems. Important information – see page 89. Have the cause of the fault eliminated immediately by a workshop. The system’s integrated self-diagnostics allows faults to be quickly remedied. If control indicator v in the instrument panel fails, for reasons of safety, the text AIrbAG appears in the odometer display.
Seats, interior Seat occupancy recognition 3 The seat occupancy recognition system deactivates the front and side airbags for the front passenger if the front passenger seat is not occupied or a Vauxhall child restraint system with transponders 3 is fitted on the front passenger seat. The curtain airbag system 3 remains activated. The control indicator for seat occupancy recognition y is located in the instrument panel. If control indicator y illuminates for approx.
88 Seats, interior Control indicator y for Vauxhall child restraint systems with transponders 3 The presence of a Vauxhall child restraint system with transponders 3 is indicated after the ignition has been switched on by permanent illumination of the control indicator y in the instrument panel, as soon as the seat occupancy recognition system has detected the child restraint system.
Seats, interior If no Vauxhall child restraint system with transponders 3 is fitted, the control indicator must not light or flash as the passenger airbag systems would not deploy. Have the cause of the fault eliminated by a workshop. 9 Warning If the Vauxhall child restraint system with transponders 3 has been fitted according to the instructions, the control indicator for Vauxhall child restraint systems with transponders must illuminate in the instrument panel when the ignition is switched on.
90 Seats, interior z The airbag systems are triggered independently of each other based on the severity of the accident and the type of impact. The side airbag system 3 and the curtain airbag system 3 are triggered together. z Each airbag deploys once only. Have a workshop replace deployed airbags immediately. z The speeds, directions of movement and deformation properties of the vehicles, and the properties of the obstacle concerned, determine the severity of the accident and triggering of the airbags.
Seats, interior z In order to prevent malfunctions when using a Vauxhall child restraint system with transponders 3 on the front passenger seat, no objects (e.g. plastic sheet, stickers or heated mats) may be placed under the child restraint system. 9 Warning Vehicles with passenger airbag and no side airbag 3: child seats facing the rear of the vehicle must not be fitted to the passenger seat, risk of fatal injury.
92 Seats, interior Vehicles with front passenger airbag can be recognised by the word AIRBAG above the glove compartment and the warning sticker on the sun visor of the passenger seat – see Fig. 17424 T. In some versions1), the warning sticker may be on the side of the instrument panel – see Fig. 17118 T. 9 Warning Vehicles with side airbag 3: No child restraint system 3 may be fitted on the front passenger’s seat; risk of fatal injury.
Seats, interior The seat occupancy recognition system detects Vauxhall child restraint systems with transponders 3 and switches off the front and side airbag systems for the front passenger’s seat. The curtain airbag system remains activated. Seat occupancy recognition – see page 87. Vehicles with seat occupancy recognition can be identified by control indicator y in the instrument panel. If control indicator y illuminates for approx.
94 Seats, interior Cigarette lighter 3 Accessory socket 3 The cigarette lighter is in the front centre console. The socket in the centre console and the cigarette lighter socket can be used to connect electrical accessories. The sockets are ready for operation when the ignition is switched on. If the engine is not running the battery will be discharged. More accessory sockets 3 can be found in the centre console beneath the rear air vents and in the Travel Assistant 3.
Seats, interior Ashtray To be used only for ash and not for combustible rubbish. 9 Warning Failure to observe these descriptions can lead to injuries which may be fatal. Vehicle passengers should be informed accordingly. Front ashtray The ash tray is in the front centre console beneath a cover. The cover opens when pressed at the point indicated. To empty, grip both sides of the ashtray insert at the spots illustrated and pull upwards. 95 Rear ashtray 3 The ash tray is in the rear centre console.
96 Seats, interior Stowage compartments Glove compartment To open, pull handle upwards. On the inside of the glove compartment cover there is a pen holder. The glove compartment should remain closed while driving. Cooled glove compartment 3 – see page 143. Centre console stowage compartment 3 Division of the stowage compartment can be changed by moving the partition in the side guides. Stowage compartment in the roof lining 3 To open, press the marked point.
Seats, interior Stowage compartments in the luggage compartment To access press down both bars and open the cover. Warning triangle ¨ 3 and first-aid kit + 3 stowage – see page 232. Stowing the spare wheel – see page 233. Jack and vehicle tools stowage – see page 235. Drink holders Drink holders, front 3 The drink holder can be found between the front seats in the centre console: slide cover 3 open. 97 Drinks holders, rear 3 The drink holder is in the console beneath the centre seat.
98 Instruments, controls Instruments, controls Control indicators The control indicators described here are not present in all vehicles. The description applies to all instrument versions. The control indicator colours mean: z z z z Red Yellow Green Blue Danger, important reminder, Warning, note, fault On confirmation, On confirmation, O Turn signal lights Control indicator flashes green. Control indicators ................................ Instrument display ...............................
Instruments, controls 99 p Alternator Control indicator lights or flashes red. It illuminates when the ignition is switched on and goes out shortly after the engine starts. Flashing while starting Battery voltage too low. Have electrical system tested by a workshop. R Brake system, clutch system Control indicator lights or flashes red. It comes on when the ignition is switched on if the hand brake is applied or if the brake and clutch fluid level is too low.
100 Instruments, controls ( Door open Control indicator lights up red It illuminates with the doors open. j Easytronic 3, start engine Control indicator lights up yellow. W Coolant temperature Control indicator lights up red Illuminates when the engine is running Stop and turn engine off, coolant temperature is too high. Risk of engine damage. For coolant temperature display see page 106. Check coolant level immediately – see page 270. 8 Exterior lights Control indicator lights green.
Instruments, controls s r Bootlid open Control indicator lights up red Parking distance sensor 3 Control indicator lights up yellow. It illuminates with the luggage compartment open, to close luggage compartment – see page 34. Fault in system. Contact a workshop for help. > Fog lights 3 Control indicator lights green. It is illuminated when the fog lights are on – see page 130.
102 Instruments, controls H Coolant level Control indicator lights up yellow. Illuminates when the engine is running Coolant fluid level too low. Stop, turn off engine. Check coolant fluid level immediately – see page 271. u Anti-lock Braking System Control indicator lights up red ! Preheating system 3, diesel particle filter 3 Control indicator lights or flashes yellow. Lights Preheating system active, switches on only if outside temperature is low.
Instruments, controls p Electro-hydraulic power assisted steering Control indicator lights up red Fault in electro-hydraulic power assisted steering system. The power assisted steering may have failed. The vehicle can be steered but considerably more force is required. Contact a workshop for assistance. v Electronic Stability Program (ESP®Plus) 3 Control indicator flashes or lights yellow. Flashing during driving System actively engaged, see page 196.
104 Instruments, controls B Adaptive Forward Lighting 3 (AFL) Control indicator flashes yellow. Flashing Fault in system. Contact a workshop for help. Flashing for 4 seconds when the ignition is switched on System adjusted for driving abroad. AFL – see page 132. Z Exhaust gases 3 Control indicator lights or flashes yellow. It illuminates when the ignition is switched on and goes out shortly after the engine starts. Illuminates when the engine is running Fault in emission control system.
Instruments, controls 105 Odometer Records the miles driven. Display in the event of airbag system malfunction – see page 86. Trip odometer Display of miles covered since reset. To set to zero, hold reset knob down for approx. 2 seconds with ignition switched on. Instrument display Tachometer Indicates engine speed. Warning zone: Maximum permissible engine speed exceeded; danger to engine. Speedometer Indicates the vehicle speed.
106 Instruments, controls For physical reasons, the engine temperature gauge shows the coolant temperature only if the coolant level is adequate. During operation the system is pressurised. The temperature may therefore rise briefly to over 100 °C. Coolant temperature display Pointer in zone at = Engine operating left temperature not yet reached Pointer between the zones = Normal operating temperature Pointer in warning zone at right or W is illuminated = Temperature too high: Stop. Switch off engine.
Instruments, controls 107 For Easytronic 3, the display flashes for a few seconds if A, M or R is selected when the engine is running but the foot brake is not depressed. Transmission display 3 Display of gear selected for automatic transmission 3 or current gear or mode for Easytronic 3.
108 Instruments, controls 12:01 17 ,0°C FM 3 90,6 MHz REG AS RDS TP 11:25 } 21 .5°C Timer Information display Triple information display Display of time, outside temperature and date/infotainment system 3 (when it is on). When the ignition is off, the time, date and outside temperature can be presented for 15 seconds by briefly pressing one of the two buttons below the display. Display F in the display indicates a fault. Have the cause eliminated by a workshop. 1 257.0 Ø 40 8 11.0 Ø 17.
Instruments, controls The type of information and how it is displayed depends on the equipment of the vehicle and the Infotainment system 3, trip computer 3 and climate control system 3 settings. Some information appears in the display in an abbreviated form. For Infotainment system see Infotainment system instructions. For climate control system see page 156. 109 : 8:56 -5 ,5°C 07.04.2004 Display F in the display indicates a fault. Have the cause eliminated by a workshop.
110 Instruments, controls 8:56 5 ,5°C 07.04.2004 Triple information display Set date and time Infotainment system off: press Ö and ; below the display as follows: Press Ö for approx. 2 seconds: Day flashes ;: Set day Ö: Month flashes ;: Set month Ö: Year flashes ;: Set year Ö: Hours flash ;: Set hours Ö: Minutes flash ;: Set minutes Ö: Clock is started. Correcting time 3 Some RDS transmitters do not send a correct time signal.
Instruments, controls 11:25 } 111 21 .5°C Range 257miles Board information display 3, selecting functions Functions and settings of some equipment 3 can be accessed via the board information display. This is done using the menus and the buttons/four-way button on the Infotainment system 3 or the left-hand adjuster wheel 3 on the steering wheel. The respective menu options are then shown in the following lines on the display.
112 Instruments, controls The functions are displayed in the following order: 11:25 } 21 .5°C System Board information display 3, system settings Press the Settings button of the infotainment system. Menu item Audio or System will appear. Press the lower button of the four-way button to reach menu item System. After pressing the right-hand part of the fourway button, the first function of the System menu is shown. Some information appears in the display in an abbreviated form.
Instruments, controls 113 The automatic setting is indicated by } in the display. To correct time with the help of RDS, select the menu item for time synchronisation from the Settings menu. Make the desired setting. Setting date and time Select the menu item for time and date setting from the Settings menu. 11:25 } 21 .5°C Deutsch 11:25 } 21 .5°C Unit Europe-SI Make the desired setting. The setting is executed upon exit from the menu item.
114 Instruments, controls Board information display 3, trip computer 3 The trip computer provides information on driving data, which is continually recorded and evaluated electronically. Access trip computer vehicle data by pressing the BC button on the infotainment system or the left adjuster wheel 3 on the steering wheel. Some information appears in the display in an abbreviated form. Once an audio function has been selected, the subsequent rows of the trip computer function are displayed.
Instruments, controls 11:25 } 21 .5°C Range 257miles Range Range is calculated from current fuel tank content and instantaneous consumption. The display shows average values. After refuelling, the vehicle updates the range automatically after a brief delay. If less than 30 miles (50 km) can be driven with the fuel remaining in the tank, the warning "Range" appears on the display.
116 FM Instruments, controls [TP] 19,5° CDin 90.6 MHz 19:36 Graphical information display 3 or colour information display 3, selecting functions The functions and settings of some equipment 3 can be accessed via the graphical information display or the colour information display. Functions are selected and executed in the menu on the display using the four-way button, the multifunction button 3 on the infotainment system or the left wheel 3 on the steering wheel.
Instruments, controls 7 FM [TP] CDin Settings Time, Date 117 19,5° 19:36 19:36 Language 90.6 MHz Units 10 . 07 . 2004 Contrast Day / Night 19,5° To select using the left adjuster wheel 3 on the steering wheel Push upwards Previous menu item. Push downwards Next menu item. Press Selection of marking, confirmation of commands. 19:36 6 Ign.
118 7 Instruments, controls Time, Date Time Date 19,5° 19:36 19:36 10 . 07 . 2004 6 Synchron. clock automatical. Setting the date and time 3 Select menu item Time, Date from the Settings menu. The menu for Time, Date is displayed. Select the menu items required: Correcting time 3 For systems with GPS receiver1), time and date are automatically set upon receipt of a GPS satellite signal.
Instruments, controls 7 13 Languages 19,5° 19:36 X Deutsch 7 Settings 19,5° 19:36 Language ~ Europe-SI Español Units Japan Nederlands Contrast Français Day / Night | | | Italiano 6 Ign. logic Selections are indicated by a 6 in front of the menu item. In systems with voice output 3, when the language setting of the display is changed the system will ask whether the announcement language should also be changed – see Infotainment system instructions.
120 Instruments, controls Setting display mode 3 The display can be adjusted to suit the light conditions, black or coloured text on a light background or white or coloured text on a dark background. Select menu item Day / Night from the Settings menu. The options are displayed. Automatic: adapted based on vehicle lighting. Always day design: black or coloured text on light background. Always night design: white or coloured text on dark background.
Instruments, controls Distance travelled Distance travelled display. Measurement may be reset to zero at any time and restarted, see "Resetting the trip computer information". Average speed Average speed calculation. Measurement may be reset to zero at any time and restarted, see "Resetting the trip computer information". Range 33miles Timer If less than 30 miles (50 km) can be driven with the fuel remaining in the tank, the warning "Range" appears on the display.
122 Instruments, controls Ü Reset BC 1 19,5° 19:36 257.0 Ø 40 11.0 Ø 17.0 Ü Reset BC 1 19,5° 19:36 All values All values miles mph gal miles/gal The information from both trip computers can be reset separately, making it possible to evaluate data over different time periods. Select the desired trip computer information. The value for the selected function will be reset and recalculated. 257.0 Ø 40 11.0 Ø 17.
Instruments, controls 123 The desired stop watch display can be selected from the Options menu 3: Ü Board Computer 19,5° 19:36 BC 1 BC 2 00:00:00 Timer Tyres Start Reset Options Stop watch Select menu item Timer from the Board Computer menu. The Timer menu is displayed. Driving Time excl. Stops The time the vehicle is in motion is recorded. Stationary time is not included. Driving Time incl. Stops The time the vehicle is in motion is recorded.
124 Instruments, controls Check control 3 Check control monitors several fluid levels, the tyre pressure 3, the remote control batteries, Vauxhall alarm system 3 and the main vehicle lighting systems, including the cables and fuses. When towing, the trailer lighting system is also monitored. Once the ignition has been switched on, all check control functions are automatically verified. Warning messages appear on the display. If there are several warning messages, they are displayed one after the other.
Instruments, controls If there is a fault in the vehicle lighting system, the respective location of the fault is displayed as text, e.g.: Brakelight check right If brake light is defective, the relevant tail light takes over the brake light function. In vehicles with tyre pressure monitoring system 3, if tyre pressure is too low, the display indicates which tyre to check, e.g.: Tyre pressure check rear right (value in bar) Check tyre pressure at next opportunity using suitable gauge.
126 Instruments, controls Warning buzzers Push lever past resistance point and hold: the windscreen wiper stages are run through; an acoustic signal sounds at position §. When starting the engine or whilst driving: z If seat belt is not fastened 3. Adjustable timed interval wipe $: Adjuster wheel right = Short intervals Adjuster wheel left = Long intervals z When driving with a door open or the tailgate ajar. z Once you have reached a certain speed if the hand brake is applied 3.
Instruments, controls Automatic wiping with rain sensor 3: To activate, press stalk briefly up $ § = = Automatic wiping with rain sensor Off The rain sensor detects the amount of water on the windscreen and automatically controls the windscreen wipers. Adjust the sensitivity of the system using the adjuster wheel: Adjuster wheel right Adjuster wheel left = = High sensitivity Low sensitivity Keep sensor area of rain sensor clean by operating the windscreen wash system.
128 Lighting Lighting Versions with daytime running lights 3: Parking lights are on when the ignition is switched on and the light switch is set to 7 or AUTO. Dipped beam is on when the engine is running. The daytime running lights switch off when the ignition is switched off. Exterior lights ....................................... Main beam, headlight flash ............... Automatic dipped beam activation 3 ....................................... Turn signal lights .................................
Lighting 129 To activate the headlight flash, pull stalk on steering wheel. Main beam is engaged for the duration of activation. The blue control indicator C is illuminated when main beam or headlight flash is on. Main beam, headlight flash To switch from dipped to main beam, press stalk forwards. To switch to dipped beam, push stalk forward again or pull towards steering wheel.
130 Lighting After operation, the turn signal stalk returns to its starting position. If the stalk is moved past the resistance point, the turn signal light remains on. When the steering wheel moves back toward the straight-ahead position, the turn signal light is automatically deactivated. Tap signal: Move stalk to resistance point and release to activate three flashes from the turn signals when changing lanes or the like. Turn signal lights To activate, press stalk up or down.
Lighting 131 Fog tail light r The fog tail light can only be switched on when the ignition is on and dipped beam or parking lights are on or if the light switch is in the AUTO 3 position and dipped beam is active. On = Off = Press >, > lights in instrument panel Press > again or switch off ignition or light The fog tail lights of the vehicle are deactivated when towing a caravan/ trailer. Reversing lights Come on when reverse gear is engaged and ignition is switched on.
132 Lighting Vehicles without automatic level control system 0 = Front seats occupied 1 = All seats occupied 2 = All seats occupied and luggage compartment load 3 = Driver’s seat occupied and luggage compartment load Vehicles with automatic level control system 0 = Front seats occupied 1 = All seats occupied 1 = All seats occupied and luggage compartment load 2 = Driver’s seat occupied and luggage compartment load Automatic headlight range adjustment 3 For vehicles with Xenon headlights, headlight beam le
Lighting 133 If the driver’s door is left open, the lights will go out after two minutes. The light is switched off immediately by inserting the key into the ignition or pulling the turn signal stalk again with the driver’s door open. Control indicator B Flashing: Fault in system. The system is not ready for operation. If the curve lighting swivelling device fails, the relevant dipped beam is switched off. The corresponding fog light is automatically switched on for reasons of safety.
134 Lighting Parking lights The front parking light and tail light of one side of the vehicle can be activated when parking: 1. Set light switch to 7 or AUTO 3. 2. Ignition off 3. Move turn signal stalk all the way up (right parking light) or down (left parking light). An acoustic signal sounds and control indicator O illuminates briefly in the instrument panel to indicate activation. Remove the ignition key before leaving the vehicle.
Lighting 135 Entry lighting 3 After unlocking the vehicle, the instrument and switch illumination as well as the courtesy lights come on for a few seconds. Illuminated mirror in the sun visors 3 The lighting switches on when the cover is opened. Glove compartment lighting Glove compartment is illuminated when lid is open and ignition on. Cigarette lighter and ashtray illumination 3 Comes on when ignition is switched on. Front reading lights 3 Left and right reading lights are individually operable.
136 Lighting Battery discharge protection Headlights when driving abroad To prevent the battery from becoming discharged, the courtesy light, reading lights, luggage compartment lighting and glove compartment lighting switch off automatically 5 minutes after the ignition is switched off. The asymmetrical dipped beam increases the field of vision on the passenger side of the lane. Vehicles with Adaptive Forward Lighting 3 (AFL) 1. Open fuse box cover in engine compartment – see page 247.
Infotainment system Infotainment system 137 Radio reception 3 Car radio reception differs from domestic radio reception: As the vehicle antenna is relatively near the ground, the broadcasting companies cannot guarantee the same quality of reception as obtained with a domestic radio using an overhead antenna. Radio reception 3................................ Infotainment system 3........................ Remote control on steering wheel 3 .. Twin Audio 3 .......................................
138 Infotainment system Twin Audio 3 AUX input 3 Twin Audio gives rear seat occupants the opportunity to listen to the audio source set on the infotainment system 3 or one of the other audio sources. The AUX input is in the stowage compartment in the centre console. Only an audio source that is not currently active on the infotainment system can be controlled using Twin Audio. Two headphone connections are available, with separate volume controls.
Infotainment system Mobile telephones and radio equipment (CB) 3 The Vauxhall installation instructions and the operating guidelines provided by the telephone manufacturer must be observed when fitting and operating a mobile telephone. Failure to do so could invalidate the vehicle’s operating permit (EU Directive 95/54/EG). Recommended prerequisites for fault-free operation: z Professionally installed exterior antenna to obtain the maximum range possible. z Maximum transmission power 10 Watt.
140 Climate control Climate control Heating and ventilation system, air conditioning system 3 ...................... Automatic air conditioning system 3 Electronic climate control system 3 ... Air vents ............................................... Cooled glove compartment 3 ............ Heated rear window, heated exterior mirrors ................................................ Heated front seats 3........................... Heated rear seats 3 ............................
Climate control 141 The set values appear on the information display. Electronic climate control system – see page 156. Automatic air conditioning system 3 Electronic climate control system 3 Provides a comfortable interior regardless of the weather, outside temperature or season. Offers the greatest comfort in the vehicle interior regardless of the conditions outside.
142 Climate control Air vents Pleasant ventilation to the head area controlled by the position of the temperature switch. To increase the air supply, set the fan to a higher speed and set the air distribution switch to M. Centre and side air vents (1) To open vent: Turn vertical adjuster wheel up. Adjust the direction of air flow by turning the horizontal and vertical adjuster wheels. To close the vents turn the adjustment wheel fully downwards.
Climate control 143 Heating takes place with the engine running and is switched off automatically after approximately 15 minutes. The heated rear window automatically switches on when the diesel particle filter is being cleaned 3 depending on the engine. Cooled glove compartment 3 Cooled air is fed into the glove compartment through a nozzle. If glove compartment cooling is not needed, turn the wheel downwards.
144 Climate control Heated front seats 3 Heated rear seats 3 Two knurled wheels beneath the centre air vent for the left and right-hand seats. Two switches at rear of centre console in front of the rear seats. Turn relevant wheel to set required heating level. When the ignition is switched on, the heating of the corresponding seat is activated by pressing the button ß. Control indicator above adjustment wheel. We do not recommend prolonged use of the highest level for people with sensitive skin.
Climate control Heating and ventilation system Air distribution Setting with the left rotary switch. L To headroom via adjustable air vents, to footwell M To headroom via adjustable air vents l Towards windscreen and front door windows J To windscreen, to front side windows, to footwell K Towards footwell Open the air vents when the switch is set to L or M. Temperature Setting with the centre rotary switch. Red area = Warm Blue area = Cold 145 Air flow Setting with the right rotary switch.
146 Climate control Heating The amount of heat is dependent on the coolant temperature and is thus not fully attained until the engine is warm. The comfort and general well-being of the vehicle occupants are to a large extent dependent on a suitable ventilation and heating setting. For rapid warming of the passenger compartment: z Set air distribution switch to desired position, preferably position J, see page 145.
Climate control 147 z Turn the temperature switch clockwise as far as it will go (warm). z Set the fan switch to 3 or 4. z Activate heated rear window Ü. z Open side air vents as required and direct them towards the side windows. Heating the foot well z Set air distribution switch to K. z Set the temperature switch in the red zone. z Switch on fan.
148 Climate control Air conditioning system 3 As a supplement to the heating and ventilation system, the air conditioning system cools and dehumidifies (dries) inflowing air. If cooling or dehumidification is not desired, switch off cooling in order to save fuel. Cooling switches off automatically at low outside temperatures. Cooling n Operation only with engine running and fan switched off: On = Press n Off = Press n again Control indicator in the button.
Climate control 149 The switched-on air recirculation system reduces air replacement. The humidity increases and the windows may mist up. The quality of the interior air deteriorates over time, which may cause drowsiness. Comfort setting z Set cooling n as desired. z Air recirculation system 4 off. z Set air distribution switch to M or L. z Set temperature switch as desired. z Switch on fan at desired speed z Open air vents as required.
150 Climate control z Cooling n on, the air conditioning compressor automatically switches itself off at low outside temperatures (icing). z Press button V: The fan will automatically switch to 4, air distribution directed on to the windscreen. z Turn the temperature switch clockwise. z Open side air vents as required and direct them towards door windows. z Switch on heated rear window Ü.
Climate control Automatic mode Basic setting for maximum comfort: z Set fan switch to A. z Set air distribution switch to desired position – see next column. z Use rotary switch to set temperature to 22 °C (a higher or lower temperature can be set as desired). z Air conditioning compressor activation – see page 152. z All front air vents open. If desired, the rear vents also 3. Deactivation of the air conditioning compressor can reduce the level of comfort and safety – see page 152.
152 Climate control When the cooling (air conditioning compressor) is active, the air is cooled and dehumidified. If cooling or dehumidification is not desired, switch off cooling in order to save fuel. Cooling switches off automatically at low outside temperatures. Air flow Setting with the right rotary switch.
Climate control 153 The exchange of fresh air is reduced in air recirculation mode. The quality of the passenger compartment air deteriorates which may cause the vehicle occupants to feel drowsy. In operation without cooling the air humidity increases, so the windows may mist up. Consequently, manual air recirculation should only be run for short periods of time. To deactivate manual air recirculation: Press button 4 again. The control indicator in the button goes off.
154 Climate control Heating The amount of heat is dependent on the coolant temperature and is thus not fully attained until the engine is warm. For rapid warming of the passenger compartment: z Set the air distribution switch to the desired position – see page 145. z Set the centre rotary switch to the desired temperature. We recommend a value of about 22 °C. z Set fan switch to A. The fan can also be manually set: Set the rotary switch to position 1 - 4. Intermediate settings are also possible.
Climate control 155 z Press button V: In switch position A, the fan automatically switches to the highest speed and air is directed to the windscreen. The automatic climate control system provides maximum cooling down to the set value. At settings below 17 °C (rotary switch all the way to the left), the system continually runs with maximum cooling. When the air conditioning compressor is running, air recirculation is automatically switched on. z Set temperature to maximum heating, i.e.
156 Climate control Electronic climate control system 3 Provides a the greatest amount of comfort in the interior regardless of the weather, outside temperature or season. FM To ensure a constant and comfortable climate in the vehicle, the temperature of the inflowing air, the air-flow rate and the air distribution are changed automatically according to climatic conditions outside the vehicle.
Climate control The temperature can be set higher or lower as desired. Different temperatures can be set for the driver and passenger sides. Switching off the air conditioning compressor (Eco appears in the display) can have a detrimental effect on comfort and safety, see page 160. All air vents (except the rear air vents 3) are controlled automatically in automatic mode. The front air vents should therefore always be open. Automatic mode Basic setting for maximum comfort: z Press AUTO button.
158 Climate control Temperature preset Using the outer knobs, temperatures can be individually set to values between 16 °C and 28 °C. For reasons of comfort, temperature can only be changed in small increments. FM [TP] CDin 90.6 MHz Climate Air distribut. AC Autom. blower Auto. recirc Cars with Quickheat 3: Depending on the outside temperature and engine temperature, the passenger compartment can be heated more quickly by means of supplementary electrical heating.
Climate control Air distribut. FM [TP] CDin 90.6 MHz The air flow can be increased or decreased by turning the central knob. To return to automatic mode: press button V or AUTO. Heated rear window, see page 143. Auxiliary heating 3, see page 163. The individual menu items are marked by rotating the centre knob and selected by pressing it. Selecting certain menus by pressing the knob will open a submenu. To exit a menu, turn the centre knob left or right to Return or Main and select.
160 Climate control Climate Air distribut. AC Autom. blower Auto. recirc Air conditioning on / off Inflowing air is neither cooled nor dehumidified. This restricts the level of comfort provided by the electronic climate control system. This may cause the windows to mist up, for example. Air distribut. To activate cooling: Select menu item AC from the manual settings menu and press to activate cooling.
Climate control FM [TP] CDin 90.6 MHz Automatic blower Strong Normal Weak Air flow Turn the centre rotary knob clockwise or anticlockwise (if no menu for manual settings is displayed). The selected fan level is indicated by x and numbers in the display. Fan control in automatic mode 3 Fan regulation in automatic mode can be modified. At speed 0 both the fan and cooling (air conditioning compressor) are switched off.
162 Climate control The air conditioning will operate for a limited period of time. Residual air conditioning on If necessary, the auxiliary heating 3 also automatically switches on. Observe notes on page 163. To cancel air conditioning, press the AUTO button. Manual air recirculation mode The air recirculation system prevents the entry of outside air and the air in the passenger compartment is circulated. Press button 4, control indicator in button.
Climate control Climate Air distribut. AC Autom. blower Auto. recirc Parking heater Auxiliary heating/ventilation 3 If the engine is switched off, the interior is heated or ventilated depending on the values that have been set and the interior temperature. The regulation is in accordance with the most recent temperature settings in the climate control system – see page 158. When the system is switched on, the temperature setting can be varied using the outer rotary knobs.
164 Climate control Parking heater Setting Start 1 Start 1 Start 1 Start 2 Start 2 Start 2 Start 3 Start 3 Start 3 On On Setting Setting Parking heater Switching on at a programmed time Three programmed times can be stored for switching on. For safety reasons only one programmed time for switching on can be active at any one time. After the heating cycle has been completed, the next required time for switching on must be activated afresh.
Climate control 165 The remote control has a range of approx. 600 m. The range can be reduced by obstructions between the sender and receiver (e.g. walls) and by low power in the battery. The system switches itself off automatically after a maximum of 60 minutes depending on the values that have been set and the interior temperature. The auxiliary heating can be switched off at any time by pressing the button §.
166 Climate control Air outlet Note Do not cover the air outlets when storing items in the luggage compartment storage compartments. If the windscreen is misted due to damp weather, temporarily set the system as described under "Window demisting and defrosting", see pages 147, 150, 159. Pollen filter The pollen filter cleans dust, soot, pollen and spores from the air entering from outside. The active carbon layer 3 eliminates most odours and harmful ambient gases from the air.
Climate control When cooling 3 (air conditioning compressor) is switched on condensation forms, which is expelled from the underside of the vehicle. At least one air vent must be open while cooling 3 (air conditioning compressor) is on in order to prevent the evaporator from icing up due to lack of air movement. Cooling switches off automatically at low outside temperatures.
168 Driving and operation Driving and operation Easytronic 3 The automatic Easytronic transmission permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control. 9 Warning Disregard of these instructions may lead to injuries or endanger life. Easytronic 3 ......................................... Automatic transmission 3 .................. Driving hints ......................................... Saving fuel, protecting the environment .......................
Driving and operation 169 It is not necessary to select the neutral position before starting. If no gear is engaged, the transmission automatically shifts into neutral position (N) before starting the engine. This can lead to a slight delay when starting. Starting the engine Operate foot brake when starting the engine. The engine can only be started with the foot brake operated. "N" appears in the transmission display.
170 Driving and operation It is also possible to start off without depressing the foot brake if the accelerator pedal is operated directly after moving the selector lever. If there is no immediate acceleration or the foot brake is not depressed, no gear is engaged and "A" flashes. After a few seconds, the display reverts to "N". Repeat previously described starting procedure. In Automatic mode, selection of other gears is automatic irrespective of driving conditions.
Driving and operation If the vehicle is in automatic mode, on movement of the selector lever to + or Easytronic shifts to manual mode and changes up or down. The transmission display shows the currently selected gear. Move selector lever toward R Reverse gear. Engage only when vehicle is stationary. Depress the foot brake, release the hand brake and move the selector lever to R. Reverse gear is engaged. "R" appears in the transmission display. The vehicle begins to "creep" when the foot brake is released.
172 Driving and operation If the vehicle is switched to manual mode while the winter program is active, the winter programme is interrupted. The winter programme resumes upon return to automatic mode. Winter program T In the event of difficulties starting off on slippery roads, press button T ("A" and T appear in the transmission display). Easytronic switches to automatic mode and the vehicle sets off in second gear.
Driving and operation When the engine speed approaches its upper limit, the transmission shifts to a higher gear during kickdown even in Manual mode. Without kickdown this automatic shift is not effected in Manual mode. Engine braking Automatic mode: When driving downhill, Easytronic does not shift into higher gears until a fairly high engine speed has been reached. When braking, Easytronic shifts down in good time.
174 Driving and operation Stopping the vehicle In Automatic or Manual mode, when the vehicle has stopped first gear (with Winter mode engaged, second gear) is engaged automatically and the clutch released. In R reverse remains engaged. When the engine is running, a gear is engaged and the foot brake is not depressed, a warning buzzer sounds when the driver’s door is opened and the gear shown in the transmission display flashes at a rapid rate. If the hand brake is not engaged, the vehicle creeps.
Driving and operation If the cause of the power failure is not a discharged battery, contact a workshop. If the vehicle must be removed from flowing traffic, release the clutch as follows: 1. Apply hand brake and switch off ignition. 2. Opening and propping up the bonnet – see page 226. 3. Clean Easytronic around the cap (see figure) so that no dirt can get into the opening when the cap is removed.
176 Driving and operation Automatic transmission 3 The automatic transmission allows automatic shifting (Automatic mode) or manual shifting (Manual mode) to take place. The engine can only be started with the selector lever in P or N. When starting in N, depress the foot brake or apply the hand brake. After the engine has started, depress the brake before engaging a gear. Do not accelerate while selecting a gear. Once a gear is engaged and the brake is released, the vehicle "creeps".
Driving and operation 177 The selector lever can only be moved out of position P or N with the ignition switched on and the foot brake applied (selector lever lock). In selector lever position N the selector lever lock is activated after a delay and only if the vehicle is stationary. In positions P or N, the control indicator j lights up red in the selector lever indicator, the selector lever is blocked, see Fig. S 12547. To engage P or R, push button on selector lever.
178 Driving and operation If the engine speed is too slow, the transmission automatically shifts to a lower gear, but not if the gear was selected below a certain speed. Electronically controlled driving programs z With adaptive programs, shifting into other gears is handled automatically based on the driving style, e.g.: If a higher gear is selected below a certain speed a downshift does not take place. – Economical driving style: at slower engine speeds.
Driving and operation z Automatic neutral shift function automatically sets the transmission to N to reduce fuel consumption, e.g. at traffic lights. The automatic neutral shift function is activated when the following occurs simultaneously: 179 z After a cold start, the operating temperature program ensures that the correct gear (increased engine speed) is selected to quickly bring the catalytic converter to the temperature required for optimum pollutant reduction.
180 Driving and operation To deactivate The winter program is switched off by: z pressing button T again, z switching off the ignition, z switching to Manual mode. To protect against damage, the startingoff aid automatically cuts out at very high transmission oil temperatures. Winter program T Press button T if you are having problems starting off on a slippery road surface. To activate The winter program can be switched in Automatic mode (T illuminates in the transmission display, see page 176).
Driving and operation Engine braking The automatic transmission automatically selects the driving program with optimal engine braking effect. As needed, lower gears can also be selected in manual mode to increase engine braking effect. 1st gear has the greatest braking effect.
182 Driving and operation Stopping the vehicle The selector lever can be left in the chosen gear with the engine running. When stopping on gradients engage hand brake or depress brake pedal. To prevent overheating of the transmission, do not increase engine revolutions to ensure smooth idling while standing if a gear has been selected. Switch off engine if stopping for a lengthy period, e.g. in traffic jams or at level crossings.
Driving and operation 183 Illumination of control indicator A can also indicate a fault in the engine electronics – see page 192. For diesel engines1) Z 19 DTL, Z 19 DT, Z 19 DTH illumination of control indicator A could also indicate that the diesel fuel filter must be drained of water, see page 270. Have the cause of the fault eliminated by a workshop. Interruption of power supply If the vehicle battery is flat, the selector lever cannot be moved out of position P or N.
184 Driving and operation Driving hints The first 600 miles / 1000 km Drive your vehicle at various speeds. Do not use full throttle. Never allow the engine to labour at low revs. Make good use of all gears. Depress the accelerator pedal a maximum of around three quarters of the available pedal travel in all gears. Do not drive faster than three quarters of maximum speed. Do not brake unnecessarily hard for the first 120 miles (200 km).
Driving and operation Overrun The fuel supply is automatically shut off during overrun, e.g. when the vehicle is being driven down long gradients or when braking. To enable the overrun cut-off to take effect, do not accelerate during overrun and, if in manual transmission mode, do not de-clutch. To prevent damage to the catalytic converter, overrun cut-off is temporarily deactivated when the catalytic converter temperature is high.
186 Driving and operation Saving fuel, protecting the environment Trend-setting technology In the development and manufacture of your vehicle, environment-friendly and in the main recyclable materials were used. The production methods used to make your vehicle are likewise environmentallycompatible. Recycling of production wastes keeps the circulation of material closed. Reduction of energy and water requirements also helps to conserve natural resources.
Driving and operation Overrun z The fuel supply is automatically shut off during overrun, e.g. when the vehicle is being driven down long gradients or when braking – see page 185. z To enable the overrun cut-off to come into action and save fuel, do not accelerate or de-clutch during overrun. Correct gear selection z High revs increase engine wear and fuel consumption. z Do not race your engine. Avoid driving at high engine speeds. Making use of the tachometer helps to save fuel.
188 Driving and operation Fuels, refuelling Fuel consumption Fuel consumption is determined under specific driving conditions – see page 283. Special equipment increases the weight of the vehicle. As a result, they can increase fuel consumption and reduce the specified maximum speed. For the first few thousand miles, friction between the engine and transmission components is higher. This increases fuel consumption.
Driving and operation 189 9 Warning Fuel is flammable and explosive. When handling fuel or in the immediate vicinity, avoid naked flames or sparks. Do not smoke. This also applies where the presence of fuel is revealed by its characteristic smell. If fuel odours occur in the car, have a workshop eliminate the fault immediately. Fuel filler neck at right rear side of vehicle. The tank flap is locked together with the doors – see page 30. Refuelling 9 Warning Care must be taken when handling fuel.
190 Driving and operation Damage to the catalytic converter or the vehicle may result if the following points are not observed: z On ignition faults, uneven running after cold start, a clear drop-off in engine power or other unusual operating symptoms which could indicate a fault in the ignition system, contact a workshop immediately. Continue driving if necessary for a short time at low speed and low revs.
Driving and operation z If the control indicator Z for exhaust gases flashes, slow down until the flashing stops and the control indicator illuminates. Contact a workshop for assistance immediately. Control indicator Z for exhaust gases – see page 192.
192 Driving and operation Flashing with the engine running indicates a fault which could lead to catalytic converter damage. You may continue driving without damage if you back off until flashing stops and the control indicator comes on. Contact a workshop immediately. Control indicator Z for exhaust Illuminates when the ignition is switched on and during the start attempt. Goes off shortly after the engine starts running.
Driving and operation In some cases, faults can be eliminated by switching off the engine and restarting. If the control light comes on again when the engine is running, contact a workshop to eliminate the cause of the fault. If A illuminates, this may also mean water in the diesel fuel filter in the engines1) Z 19 DTL, Z 19 DT and Z 19 DTH. Where necessary, have the fuel filter inspected by a workshop for any residual water. If it illuminates briefly, but does not recur, it is of no significance.
194 Driving and operation Diesel particle filter 3 The diesel particle filter system removes polluting soot particles out of the engine exhaust gases. The system includes a selfcleaning function that operates automatically while driving. The filter is cleaned by burning the trapped soot particles at a high temperature. There may be an increase in fuel consumption, exhaust smell, and engine cooling fan operation 3 during the self-cleaning operation.
Driving and operation We recommend that you do not turn the ignition off until the self-cleaning operation is complete. If you must turn the ignition off before the operation is complete, then the operation will automatically resume when driving the next time and after the engine has reached its normal operating temperature. The control indicator ! goes off as soon as the self-cleaning operation is complete. 195 Maintenance Have all maintenance work carried out at the intervals specified.
196 Driving and operation Drive Control Systems Interactive Driving System (IDS+) 3 The IDS+ combines the sensors and control units of the Electronic Stability Program (ESP®Plus), the Anti-lock Brake System (ABS) and Continuous Damping Control (CDC). This provides both excellent driving dynamics and greater safety. Electronic Stability Program (ESP®Plus) 3 ESP®Plus improves driving stability when necessary in any driving situation regardless of the type of road surface or tyre grip.
Driving and operation ESP®Plus is ready for operation as soon as the ignition is switched on and control indicator v goes out. Illuminates while driving: The system is switched off or a fault has occurred. The vehicle can continue to be driven. However, driving stability may worsen depending on the nature of the road surface. Control indicator v flashes when ESP®Plus is in action.
198 Driving and operation Continuous Damping Control 3 (CDC) Normal mode CDC automatically adapts vehicle damping to the current driving situation and road conditions. The system continually monitors wheel and vehicle movements and immediately modifies the damping of each shock absorber. Chassis calibration is optimally adapted to the driving situation and road conditions. Continuous Damping Control is always in normal mode with the ignition is switched on.
Driving and operation Deactivating SPORT mode Briefly press the SPORT button again. The LED in the button goes out. The Continuous Damping Control system resumes Normal mode. 199 The system’s integrated self-diagnostics allows faults to be quickly remedied. SPORT mode is switched off by switching off the ignition or switching off the winter program 3 (vehicles with automatic transmission 3). Winter program, see page 180.
200 Driving and operation Cruise control 3 Cruise control can store and maintain speeds of approx. 20 to 125 mph (30 to 200 km/h). Deviation from the saved speed is possible on uphill or downhill inclines. For safety reasons the cruise control cannot be activated until the foot brake has been operated once. Cruise control is operated with buttons m, g, and § on the turn signal stalk. Do not use the cruise control if it is not advisable to maintain a constant speed (e.g.
Driving and operation Decelerate With cruise control active, hold down button g or briefly press it repeatedly: speed is reduced continuously or in steps of 1.2 mph (2 km/h). When button g is released the current speed is stored and maintained. 201 To deactivate Briefly press button §: Cruise control is switched off, control indicator m goes out and the vehicle slowly decelerates. To continue driving, depress the accelerator pedal in the usual manner.
202 Driving and operation Parking distance sensor 3 The parking distance sensor makes reverse parking easier by measuring the distance between the vehicle and an obstacle, and giving an acoustic signal in the passenger compartment. The system registers distance by means of four sensors in each of the front and rear bumpers. To activate With the ignition switched on, the front and rear parking distance sensor systems are automatically activated when reverse gear is engaged.
Driving and operation Caravan/trailer towing equipment 3, caravan/trailer towing The system automatically detects if a towbar is properly fitted to the vehicle. If the vehicle approaches an obstacle to the front or rear, an series of signals is sounded in the vehicle interior. The interval between the signals becomes shorter as the distance is reduced. If the distance is less than 30 cm, the signal will be continuous.
204 Driving and operation The vehicle is automatically raised at the rear, increasing the spring travel and ground clearance. The automatic level control system is activated after approx. 2 miles (3 km), depending on the vehicle loading and the nature of the road surface. Headlight range adjustment – see page 131. Do not use full load in the event of faults. Have the cause of the fault rectified straight away by a workshop.
Driving and operation Once the ignition is switched on, the system is operational and will continuously monitor the tyre pressures at speeds of approx. 20 mph (30 km/h) and above. 9 Warning The tyre pressure monitoring system does not replace manual checks with a suitable gauge. 205 Ü Board Computer BC 1 BC 2 Timer Tyres Check tyre pressures at least every 14 days and prior to any long journey; the tyres should be checked when cold. Don’t forget to check the spare 3. Tyre pressure – see pages 213, 288.
206 Driving and operation Warning messages in the graphical information display 3 or colour information display 3 In the version with check control 3 differing tyre pressures while driving are indicated by messages on the information display. The message appears in abbreviated form depending on the version.
Driving and operation General information The tyre pressure monitoring system is not ready for operation if the emergency/spare wheel is used and is not fitted with a pressure sensor; the control indicator w illuminates yellow. The tyre pressure monitoring system remains operational for the other three wheels. Control indicator w in yellow as fault message If control indicator w illuminates yellow while driving, there is a fault in the tyre pressure monitoring system.
208 Driving and operation Brake system Foot brake The foot brake comprises two independent brake circuits. The brakes are an important factor for traffic safety. If one brake circuit faults, the vehicle can still be braked with the other brake circuit. However the braking effect will occur at a lower pedal position and considerably more force is required. The braking distance is longer. Contact a workshop before continuing to drive.
Driving and operation 209 Check the brake lights before starting out on a journey. On vehicles with check control 3 the brake lights are checked automatically – see page 124. Shortly after starting each journey the effectiveness of the brake system should be tested at low speed and without inconveniencing other traffic, especially if the brakes are wet, e.g. after the vehicle has been washed. The brake fluid level should be checked regularly.
210 Driving and operation Anti-lock Braking System (ABS u) Fault ABS continually monitors the brake system and prevents the wheels from locking regardless of the type of road surface or tyre grip. It starts to regulate the braking pressure as soon as a wheel shows a tendency to lock. The vehicle remains steerable, even in the event of very heavy braking, for instance on bends or when swerving to avoid an obstacle.
Driving and operation Wheels, tyres See page 288 for suitable tyres and restrictions. Tyres fitted in the factory are adapted to the chassis and provide optimum driving comfort and safety. Changing tyre/wheel type Before changing to other tyres or wheels, note the necessary changes. If tyres of a different size than those fitted at the factory are used, the electronic speedometer may require reprogramming to ensure that the correct speed is displayed.
212 Driving and operation Fitting new tyres Fit tyres in pairs or in sets, which is even better. Ensure that tyres on one axle are z the same size z the same design z the same make z and have the same tread pattern. Fit directional tyres such that they roll in the direction of travel. The rolling direction is indicated by a symbol (e.g. an arrow) on the sidewall. Tyres fitted opposing the rolling direction (e.g. when a tyre is changed) should be refitted as soon as possible.
Driving and operation Tyre pressure Check tyre pressures, including the spare wheel, at least every 14 days and prior to any long journey; the tyres should be checked when cold. Don’t forget to check the spare. Use the valve cap key to make unscrewing the valve caps easier. The key is located on the inside of the tank flap. In vehicles with tyre pressure monitoring system 3 there is an adapter in the valve cap key. Screw adapter to valve before attaching tyre pressure gauge, see page 204.
214 Driving and operation Check tyres regularly for damage (penetrated foreign bodies, punctures, cuts, cracks, bulges in side walls). Check wheels for damage. If damage or unusual wear is found, contact a workshop. 9 Warning Damage may lead to tyre blow-out. Tyre condition, wheel condition Drive over edges slowly and at a right angle if possible. Driving over sharp edges can lead to hidden tyre damage and wheel damage which is only noticed later on. Tread depth Check tread depth regularly.
Driving and operation General information z The danger of aquaplaning is greater if the tyres are worn. z Tyres age, even if they are used only very little or not at all. A spare wheel which has not been used for six years should be used only in emergencies; drive slowly when using such tyres. z Never fit used tyres the previous history and use of which you do not know. z So as not to impair brake cooling, use only wheel trims approved for use on your vehicle. The legally permissible minimum tread depth (1.
216 Driving and operation Winter tyres 3 For notes on fitting new tyres – see page 212. See page 288 for restrictions. Winter tyres improve safety at temperatures below 7 °C and should therefore be fitted on all the wheels. The design of summer tyres means they have limited qualities for winter driving.
Driving and operation Wheel trim on steel wheels could come into contact with parts of the chain and be damaged. Remove the wheel trim – see page 237. Tyre chains may only be used at speeds up to 30 mph (50 km/h) and, when travelling on roads that are free of snow, they may be used for brief periods only since they are subject to rapid wear on a hard road and may snap. 217 Temporary wheel 3 Tyre chains must not be used on the temporary spare wheel.
218 Driving and operation Roof racks 3 9 Warning Disregard of these notes can lead to injuries which may be fatal. Vehicle passengers should be informed accordingly. For safety reasons and to avoid roof damage, we recommend using the Vauxhall roof rack system approved for your vehicle. Fasten the roof rack following the instructions that accompany the system. Driving hints – see page 184. Version without roof railing Fold fitting opening covers upward.
Driving and operation 219 Towing equipment 3 9 Warning Disregard of these notes can lead to injuries which may be fatal. Vehicle passengers should be informed accordingly. Only use a trailer towing device approved for the vehicle. Have a towing device fitted by workshop, who will inform you of any possible trailer load increases. They will have the instructions for fitting the device and any necessary changes to the vehicle concerning cooling, heat shields or other devices.
220 Driving and operation Checking the tensioning of the coupling ball bar z Red marking on turn knob points towards green marking on coupling ball bar. z Gap of approx. 6 millimetres between rotary knob and coupling ball bar. z Key is in lock. Otherwise, the coupling ball bar must be tensioned before it is inserted into the coupling housing: z Open coupling ball bar. z Pull turn knob out and then turn it clockwise as far as it will go – see figure.
Driving and operation 221 Important Check that the coupling ball bar is correctly installed: z Red marking on turn knob points towards white marking on coupling ball bar. z No gap between turn knob and coupling ball bar. z Coupling ball bar must be seated firmly in coupling housing. z Coupling ball bar must be locked and key must be removed. Open coupling ball bar. Remove key and put on provided protective clip. When the coupling ball bar is locked the turn knob can no longer be pulled out.
222 Driving and operation Caravan/trailer towing 1) Caravan and trailer loads The permissible caravan/trailer loads are vehicle- and engine-dependent maximum values which must not be exceeded. The actual caravan/trailer load is the difference between the actual gross weight of the caravan/trailer and the actual coupling socket load with the caravan/trailer attached.
Driving and operation Trailer Stability Assist 3 (TSA) TSA monitors vehicle movements when towing a caravan or trailer. If the system detects lurching movements, engine power is reduced and the vehicle/trailer combination is selectively braked until the lurching ceases.
224 Driving and operation Driving characteristics, towing tips In the case of trailers/caravans with brakes, attach breakaway stopping cable to eye. The Parking distance sensor system at the rear 3 is deactivated when towing a caravan/trailer. If it is necessary to apply the brakes fully, depress the brake pedal as hard as possible. Before attaching the trailer/caravan, lubricate the ball of the trailer/caravan towing device.
Driving and operation 225 The cooling fan is electrically operated. Its cooling power is therefore independent of the engine speed. For vehicles with automatic transmission 3 or Easytronic 3 in automatic mode it is sufficient to apply full throttle. Since a considerable amount of heat is generated at high engine speeds and less at slower speeds, do not shift down when climbing hills whilst the vehicle is still coping with the gradient in the higher gear.
226 Self-help, vehicle care Self-help, vehicle care Diesel fuel system, bleeding ............... Bonnet .................................................. Starting................................................. Towing .................................................. Warning triangle ¨ 3, first-aid kit + 3.................................. Spare wheel 3...................................... Jack £ 3 and vehicle tools 3 ............ Changing wheels ................................. Tyre repair kit 3 ...
Self-help, vehicle care 227 Starting Do not start with quick charger This prevents damage to electronic components. Do not start by pushing or towing Because your vehicle is fitted with a catalytic converter, it must not be started by pushing or towing – see page 190. The vehicle can only be started using jump leads – see following page. There is a safety catch on the underside of the bonnet: lift this upwards and open the bonnet.
228 Self-help, vehicle care Starting the engine with jump leads 3 A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle. 9 Warning Be extremely careful when starting with jump leads. Any deviation from the following instructions can lead to injuries or damage caused by battery explosion or damage to the electrical systems of both vehicles. z Never expose the battery to naked flames or sparks.
Self-help, vehicle care z Do not connect leads to negative terminal of discharged battery! z Start the engine of the vehicle providing the jump start. z The connection point should be as far away from the discharged battery as possible. z After 5 minutes, start the other engine. Start attempts should be made at intervals of 1 minute not last longer than 15 seconds. z Route the leads so that they cannot catch on rotating parts in the engine compartment.
230 Self-help, vehicle care Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. 9 Warning For braking and steering, significantly higher forces are required: brake assistance and steering assistance are effective only with the engine running. To prevent the entry of exhaust fumes from the towing vehicle, switch on the air recirculation 3 and close the windows.
Self-help, vehicle care 231 Contact a workshop. If the automatic clutch is released manually after a power failure on vehicles with Easytronic 3, towing is not permitted, see page 174. In this case, contact a workshop immediately. After towing, unscrew towing eye by rotating clockwise and insert and close the cap. Towing service Entrust your vehicle only to the towing service of your choice and obtain an estimate on towing costs before employing any towing service.
232 Self-help, vehicle care When loading vehicle, always ensure that warning triangle, first-aid cushion or firstaid kit is accessible. Warning triangle ¨ 3, first-aid kit + 3 Store the warning triangle and the first-aid kit (or cushion) in the stowage compartment in the luggage compartment right-hand side trim. To open the cover, push bar downward and flip open the cover.
Self-help, vehicle care Spare wheel 3 Some vehicles are equipped with a tyre repair kit instead of a spare wheel. See page 239. The spare wheel (temporary spare wheel) is stowed in the luggage compartment under the floor cover. To open the floor cover, fold out release lever by pushing at the marked point and raise up the floor cover all the way. Remove protective cap and slacken wing nut. Remove spare wheel temporary spare wheel). The vehicle tools and the jack are beneath the spare wheel.
234 Self-help, vehicle care Notes on temporary spare wheel z Using a temporary spare wheel may change the driving behaviour of the vehicle, particularly if using winter tyres 3. Replace defective tyre as quickly as possible, balance wheel and fit to vehicle. z Fit only one temporary spare wheel. z Do not drive faster than 50 mph (80 km/h). z Take curves slowly. Stow away vehicle tools and jack – see page 235. Place defective wheel in spare wheel well with outside facing upward.
Self-help, vehicle care 235 Notes on directional tyres 3 Directional tyres only achieve their full performance potential when mounted in the prescribed direction of rotation. If after a flat tyre the tyre or spare wheel is mounted against the prescribed direction of rotation, observe the following: z Driving conditions may be altered. Replace the defective tyre as soon as possible, balance the wheel and mount it on the vehicle. z Do not drive faster than 50 mph (80 km/h).
236 Self-help, vehicle care Changing wheels There may be a tyre repair kit instead of a spare wheel – see page 239. To ensure your safety, make the following preparations and observe the following information when changing wheels: z Park the vehicle on a level, firm and nonskid surface. z Switch on hazard warning lights, apply hand brake, automatic transmission 3 selector lever in P, manual transmission or Easytronic 3 - engage 1st or reverse gear. z Correctly set up the warning triangle.
Self-help, vehicle care 1. Prise off the wheel trim using the hook included with the vehicle tools. Vehicle tools – see page 235. If the wheel trim has visible wheel bolts 3, the trim can remain on the wheel. The retaining washers 3 on the wheel bolts must not be removed. Alloy wheels 3: Disengage the wheel bolt caps with a screwdriver and remove. Protect the wheel by inserting a soft cloth between the screwdriver and ally wheel. 237 2.
238 Self-help, vehicle care 3. There are plastic retainers at the front and rear of the vehicle underbody for positioning the jack. The location of each retainer is indicated by a mark on the bottom edge of the vehicle. 4. Before attaching jack 3 set to required height by turning the eye by hand. Fit the jack 3 at the front – or rear – in such a way that the jack head engages in the plastic retainer beneath the vehicle. Check that it is properly engaged.
Self-help, vehicle care 10. Before refitting the wheel trim, clean the wheel around the retaining clips. Valve symbol 3 on back of wheel trim must point towards valve on wheel. Align and refit wheel trim or wheel bolt caps 3. Alloy wheels 3: Align and refit wheel bolt caps 3. 11. Stow replaced wheel, tools and warning triangle in luggage compartment – see pages 232, 233 and 235. 6. Change the wheel. For notes on temporary spare wheel – see page 234. 7.
240 Self-help, vehicle care The tyre repair kit is in a compartment in the spare wheel well of the luggage compartment. 1. Take the pouch with the tyre repair kit from the compartment. Carefully remove the components from the pouch. 2. Remove the compressor. 3. Remove the electrical connection cable and air hose from the stowage compartments on the underside of the compressor. 4. Screw the compressor air hose to the connection on the sealant bottle. 5.
Self-help, vehicle care 7. Screw the filler hose to the tyre valve. 8. The switch on the compressor must be set to §. 9. Connect the compressor plug to the accessory socket or cigarette lighter socket. Accessory socket – see page 94. 10. Switch on ignition. To prevent battery discharge, we recommend that you leave the engine running. 11. Set the rocker switch on the compressor to I. The tyre is filled with sealant. 12. While the sealant bottle drains (approx.
242 Self-help, vehicle care Drain excess tyre pressure with the button over the pressure indicator. Do not run the compressor for more than 10 minutes, see "Important information" on page 243. 15. Detach the tyre repair kit. Screw the filler hose to the free connection on the sealant bottle. This prevents sealant leakage. Stow the tyre repair kit in the luggage compartment. 16. Wipe away any sealant spill with a cloth. 17.
Self-help, vehicle care Important 9 Warning Do not drive faster than 50 mph (80 km/h). Do not use the temporary spare wheel for a lengthy period. Steerability and driving behaviour may be impaired. The driving comfort of the repaired tyre is severely affected, therefore have this tyre replaced. If the compressor makes abnormal noises or heats up greatly, switch it off for at least 30 minutes. The integrated safety valve opens at a pressure of 7 bar. Protect the compressor from moisture and rain.
244 Self-help, vehicle care We recommend carrying a complete set of fuses. Before replacing a fuse, turn off the respective switch and the ignition. Spare fuses are kept on back of fuse box cover at instrument panel. For opening cover – see next page. A defective fuse (Fig. 17259 T) can be recognised by its melted wire. A new fuse should only be installed after the cause of the fault has been rectified.
Self-help, vehicle care Fuses and the most important circuits they protect Some circuits may be protected by several fuses. Fuse box in passenger compartment The fuse box is on the left, on the outside of the instrument panel. Open door. Disengage cover by pulling firmly and remove. No.
246 Self-help, vehicle care No. 11 12 13 14 15 Fuse box in luggage compartment The fuse box is located on the left side of the luggage compartment, in the stowage compartment. Press down both bars and open the cover. Spare fuses, fuse extractor – see page 244. Some circuits may be protected by several fuses. No.
Self-help, vehicle care 247 Some circuits may be protected by several fuses. No. Circuit 1 Engine electronics, transmission electronics 2 Starter 3 Horn 4 Air conditioning system, climate control system 5 Windscreen wash system, front and rear 6 Diesel fuel filter heating Fuse box in engine compartment The fuse box is in the box at the front left side of the engine compartment. 9 Warning Switch off engine before opening the fuse box in the engine compartment, risk of injury.
248 Self-help, vehicle care No. 27 28 29 30 31 32 33 No. Circuit 7 Central control unit, ESP®Plus 8 Headlights, windscreen washing nozzles 9 Power steering, brake servo 10 Adaptive Forward Lighting 11 Windscreen wipers 12 Central control unit, ESP®Plus 13 Headlight wash system 14 Oxygen sensor 15 Engine control unit1) 16 ABS Rating 15 A 10 A 7.5 A 10 A 30 A 7.5 A 30 A 10 A 10 A 5A No.
Self-help, vehicle care Bulb replacement Headlight aiming We recommend that headlight adjustment be carried out by a workshop which will have special equipment. Before replacing a bulb, switch ignition off and switch relevant switch off. Only hold new bulb at base! Do not touch the bulb glass with bare hands, otherwise fingerprints on the glass evaporate. Residue builds up on the reflector eventually resulting in a dull reflector.
250 Self-help, vehicle care Halogen headlight system dipped and main beam Dipped beam Headlights with separate systems for main beam 1 (inner bulbs) and dipped beam 2 (outer bulbs). 2. To change the bulb on the left, remove filler neck from windscreen wash system bottle, see page 249. As the headlight has to be removed, have the bulb on the right changed by a workshop. 1. Open bonnet. 3. Turn the headlight cover anticlockwise and remove. 4. Push down bulb at bulb holder.
Self-help, vehicle care 5. Remove the bulb holder with bulb from the reflector. 6. Detach bulb from bulb mounting. Main beam 7. Insert new bulb into bulb mounting, without touching the glass. 1. Open bonnet. 8. Insert new bulb so that the two lugs on the bulb mounting engage in the recesses in the reflector. 9. Engage the bulb holder. 10. Reposition the headlight cover and turn it clockwise. 11.
252 Self-help, vehicle care 5. Press spring wire clip forward, disengage to the right and open. 6. Remove bulb from reflector housing. 7. When fitting a new bulb, engage the lugs in the recesses on the reflector without touching the glass. 8. Engage spring wire clip, plug connector onto bulb. 9. Reposition the headlight cover and turn it clockwise. 10. After changing the bulb on the left, insert and engage filler neck for windscreen wash system bottle, see page 249.
Self-help, vehicle care Main beam 1. Open bonnet. 2. To change the bulb on the left, remove filler neck from windscreen wash system bottle, see page 249. As the headlight has to be removed, have the bulb on the right changed by a workshop. 3. Turn the headlight cover anticlockwise and remove. 4. Detach plug connector from bulb. 5. Press spring wire clip forward, disengage to the right and open. 253 6. Remove bulb from reflector housing. 7.
254 Self-help, vehicle care Adaptive Forward Lighting system 3 Xenon headlight system for main and dipped beam together with curve illumination based on steering angle. 9 Warning Xenon headlights operate at very high voltage. Do not touch, risk of fatal injury. Only have bulbs for dipped beam, main beam, turn lighting, parking lights and indicators changed by a workshop. Halogen headlight system, Xenon headlight system, parking lights 1. Open bonnet. 2.
Self-help, vehicle care 255 Halogen headlight system, Xenon headlight system, front indicator lights Have bulbs changed by a workshop. Side turn signal lights Have bulbs changed by a workshop. Fog lights 3 Have bulbs changed by a workshop. 5. Remove bulb from socket. Tail lights 6. Insert new bulb, without touching the glass. 1. To open the storage compartment, push both bars down. Also remove flap behind storage compartment by pushing the lugs. 7.
256 Self-help, vehicle care 2. Hold bulb housing from outside, slacken fastening nuts using wheel bolt spanner 3 and unscrew by hand. Remove bulb housing to rear. Wheel bolt spanner 3 – see vehicle tools, page 235. 3. Detach cable plug from bulb housing. 4. Press the retaining lugs on the outer edges of the bulb holder towards each other. Remove the bulb holder.
Self-help, vehicle care 257 5. Remove bulb from socket. 6. Insert new bulb, do not touch the glass. Engage light holder in light housing. Engage cable plug. Insert light housing into body and tighten fastening nuts by hand. Close cover and storage compartment. Bulbs in bulb carrier Number plate light 1 2 3 4 5 1. Open luggage compartment. = = = = = Reversing light Turn signal light Rear fog light Tail light Tail light/brake light 2. Unscrew both screws on underside of tailgate handle.
258 Self-help, vehicle care Courtesy light 2. Remove bulb from socket. 4. Insert new bulb, without touching the glass. Front courtesy light, reading lights 3 To ensure that no power is supplied to the lights, close the doors before removing. 3. Insert new bulb without touching the glass with your hands. 5. Insert light insert and secure using a screwdriver. 1. Lever the lens out of the housing recesses. 3. Press bulb slightly towards spring clip and remove. 4. Mount lens and engage in position.
Self-help, vehicle care Instrument illumination, information display illumination 3 Have bulbs changed by a workshop. Glove compartment lighting, luggage compartment lighting, foot well lighting 3 To ensure that no power is supplied to the lights, close the doors or hold the contact switch depressed before removing. 1. Prise the light out with a screwdriver. 2. Press bulb slightly towards spring clip and remove. 3. Insert new bulb, without touching the glass. 4.
260 Self-help, vehicle care Vehicle care When caring for your vehicle, observe all national environmental regulations, particularly when washing it. Regular, thorough care helps to improve the appearance of your vehicle and maintain its value over the years. It is also prerequisite for warranty claims for any paint or corrosion damage. The following pages contain tips for vehicle care which, if used properly, will help combat the unavoidable damaging effects of the environment.
Self-help, vehicle care Clean edges and folds on opened doors and flaps as well as the areas they cover. Thoroughly rinse off and leather-off the vehicle. Rinse leather frequently. Use separate leathers for paint and window surfaces: remnants of wax on the windows will impair vision. Observe national regulations. Waxing Wax your vehicle regularly, in particular after it has been washed using shampoo and at the latest when water no longer forms beads on the paintwork, otherwise the paintwork will dry out.
262 Self-help, vehicle care Plastic and rubber parts For additional cleaning of plastic and rubber parts use Cleaner. Do not use any other agent, and in particular do not use solvents or petrol. Do not use high-pressure jet cleaners. Wheels and tyres Do not use high-pressure jet cleaners. Interior and upholstery Clean the vehicle interior, including the instrument panel fascia, using interior cleaner. The instrument panel should only be cleaned using a soft damp cloth.
Self-help, vehicle care 263 When washing the engine with a steam jet, do not direct the jet at components of the anti-lock braking system, the air conditioning system, the climate control system, the auxiliary heater or the belt drive or its components. Underbody Your vehicle has a factory-applied PVC undercoating in the wheel arches (including the longitudinal members) which provides permanent protection and needs no special maintenance.
264 Service plan, maintenance Service plan, maintenance Inspection system ................................ Genuine Vauxhall Parts and Accessories ........................................ A note on safety .................................. Checking and topping up fluids ......... Engine oil .............................................. Diesel fuel filter .................................... Coolant ................................................. Brake fluid ............................................
Service plan, maintenance The National Conciliation Service, Retail Motor Industry Federation, 9 North Street, RUGBY, CV21 2AB If you have a problem whilst abroad: The Service Departments of Adam Opel GmbH and General Motors branches everywhere will provide information and assistance: In Luxembourg please contact the General Motors Service Department in Antwerp – Belgium Tel.
266 Service plan, maintenance The service interval display takes account of off-the-road periods during which the battery is disconnected. For vehicles with flexible oil change and service intervals, the length of these intervals is based on several parameters stemming from usage. For this reason, various engine-specific data is continually gathered and is used to calculate the remaining distance until the next service.
Service plan, maintenance 267 Genuine Vauxhall Parts and Accessories We recommend that you use "Genuine Vauxhall Parts and Accessories" and conversion parts approved expressly for your vehicle type. These parts have undergone special tests to establish their reliability, safety and specific suitability for Vauxhall vehicles.
268 Service plan, maintenance Engine oil Information on engine oils is found in the Service Booklet. Engine oil level and consumption Every engine consumes engine oil for technical reasons. The engine oil consumption cannot be assessed until a fairly long distance has been driven, and may be above the specified value when the vehicle is first being driven (run-in period). Frequent driving at high revs increases engine oil consumption.
Service plan, maintenance To check the engine oil level, insert wiped oil dipstick into handle as far as it will go. Top engine oil up if the level has dropped into the range of the top-up mark MIN. Top up with the same brand of engine oil that was used during the previous oil change, following the instructions in the service booklet. The engine oil level must not exceed the upper mark MAX on the dipstick. Excess engine oil must be drained off or extracted.
270 Service plan, maintenance Diesel fuel filter Coolant On each engine oil change, have the fuel filter checked for any water residue by a workshop. The –glycol-based – coolant provides excellent corrosion protection for the heating and cooling systems as well as antifreeze protection down to approx. -28 °C. It remains in the cooling system throughout the year and need not be changed.
Service plan, maintenance 271 When the engine is at operating temperature, coolant level rises. It falls again when the system cools. If it falls below the KALT/COLD mark when the system is cold, top up to the mark. Top up antifreeze. If no antifreeze is available, top up with clean tap water. If tap water is unavailable, distilled water can be used. Coolant level Hardly any losses occur since the cooling system is sealed and it is thus rarely necessary to top up the coolant.
272 Service plan, maintenance Coolant temperature If the temperature gauge enters the righthand (warning) zone or control indicator W illuminates, check the coolant level immediately. Use of certain brake fluids can lead to damage or reduced braking effect. We therefore recommend that you use only high performance approved brake fluid. Extreme cleanliness is needed when topping up, since contamination in the brake fluid can cause brake system malfunctions.
Service plan, maintenance Brake fluid change Brake fluid is hygroscopic, i.e. it absorbs water. If the brakes become hot, such as when driving on long downhill stretches, vapour bubbles can occur in the water, which can have an extremely adverse effect on braking power (depending on the proportion of water). Windscreen wiper The fluid change intervals specified in the Service Booklet must therefore be observed.
274 Service plan, maintenance To ensure proper operation of the rain sensor 3, the sensor area must be free from dust, dirt and ice. The windscreen wash system must also be operated at regular intervals and the sensor area must be deiced. Vehicles with rain sensor 3 can be identified by the sensor area near the top of the windscreen. Service setting for front windscreen wipers (e.g. for changing or cleaning the front wiper blades).
Service plan, maintenance Fill only with clean water to prevent the nozzles from clogging. To improve cleaning efficiency, we recommend that you add a little Vauxhall Windscreen Wash Solvent.
276 Service plan, maintenance Laying up the vehicle for more than 4 weeks can lead to battery discharge, which may reduce the service life of the battery. Disconnect battery from on-board power supply by detaching negative terminal (Vauxhall alarm system 3 is then disabled). Protecting electronic components Ensure that ignition is switched off before connecting battery. Then perform the following actions: To avoid damaging the vehicle, do not make any modifications to the electrical system, e.g.
Service plan, maintenance Vehicle decommissioning Observe national regulations. If the vehicle is to be parked for several months, to avoid damage have the following work performed by a workshop. z Wash and preserve the vehicle – see page 260. z Check corrosion protection in engine compartment and on underbody and repair if necessary. z Clean and preserve rubber seals on bonnet and doors. z Change engine oil – see page 269. z Check antifreeze and corrosion protection – see page 270.
278 Technical data Technical data Vehicle documents, identification plate ................................................... Vehicle identification data.................. Coolant, brake fluid, oils ..................... Engine data.......................................... Performance......................................... Fuel consumption, CO2 emissions ...... Weights, payload and roof load ........ Tyres ..................................................... Electrical system ........................
Technical data In other design variants, the identification plate may also be affixed to the dashboard. Engine code and engine number: stamped on left-hand side of engine on crankcase. Vehicle identification data The vehicle identification number is stamped on the identification plate and beneath a cover on the floor of the vehicle between the front door and seat on the right-hand side. 279 Coolant, brake fluid, oils Only use approved fluids.
280 Technical data Engine data Sales designation Engine identifier code 1.8 Z 18 XE 1.8 Z 18 XER 2.0 Turbo Z 20 NET 2.2 DIRECT Z 22 YH 2.8 V6 Z 28 NEL 2.
Technical data Engine data Sales designation Engine identifier code 1.9 CDTI Z 19 DTL 1.9 CDTI Z 19 DT 1.9 CDTI Z 19 DTH 3.0 CDTI Z 30 DT 4 4 4 6 Piston displacement (cm ) 1910 1910 1910 2958 Brake horse power (kW/bhp) at rpm 74 3500 88 3500 to 4000 110 4000 135 4000 Torque (Nm) at rpm 260 1700 to 2500 280 2000 to 2750 320 2000 to 2750 400 1900 to 2700 Diesel Diesel Diesel Diesel Number of cylinders 3 Type of fuel 1) 2) 2) 492) 49 49 Max.
282 Technical data Performance (approx.
Technical data Fuel consumption, CO2 emissions Directive 80/1268/EEC (last changed by 2004/3/EC) has applied for the measurement of fuel consumption since 1996. The directive is oriented to actual driving practices: Urban driving is rated at approx. 1/3 and off-road driving with approx. 2/3 (urban and extra-urban consumption). Cold starts and acceleration phases are also taken into consideration. The specification of CO2 emission is also a constituent of the directive.
284 Technical data Fuel consumption (approx. l/100 km), CO2 emissions (approx. g/km) (tyre width up to 225 mm) Engine1) Z 18 XE Manual/sports/Easytronic/automatic transmission urban extra-urban total CO2 –/11.0/–/– 10.3/10.4/10.0/– –/ 6.1/–/– 5.9/ 6.1/ 5.7/– –/ 7.9/–/– 7.5/ 7.7/ 7.3/– –/ 190/–/– 180/ 185/ 175/– Z 18 XER Z 20 NET Z 22 YH Z 28 NEL Z 28 NET –/12.8/–/– –/ 6.6/–/– –/ 8.9/–/– –/ 214/–/– 10.9/10.9/–/11.6 6.6/ 6.5/–/ 6.4 8.2/ 8.1/–/ 8.3 197/ 194/–/ 199 15.7/–/–/17.4 15.7/–/–/17.4 7.
Technical data Weights, payload and roof load The payload is the difference between the permitted gross vehicle weight (see identification plate, page 278) and the EC kerb weight. To calculate the kerb weight, enter the data for your vehicle below: z Kerb weight from table 1, page 286 + .............. kg z Additional weight of equipment versions from table 2, page 287 + .............. kg z Weight of heavy accessories from table 3, page 287 + .............. kg Total = .............. kg is the EC kerb weight.
286 Technical data Weights (kg), Table 1, kerb weight1) Model Engine2) Manual transmission Easytronic Automatic transmission Signum with air conditioning system or climate control system Z 18 XE 1495 – – Z 18 XER 1495 1495 – Z 20 NET 1575 – – Z 22 YH 1550 – 1580 Z 28 NEL 1650 – 1675 1) 2) Z 28 NET 1650 – 1675 Z 19 DTL 1605 – – Z 19 DT 1605 – – Z 19 DTH 1613 – 1638 Z 30 DT 1715 – 1733 According to EC Directive, including assumed weights for driver (68 kg), lug
Technical data Weights (kg), Table 2, Additional weight of equipment versions Engine1) Z 18 XE Z 18 XER Z 20 NET Z 22 YH Z 28 NEL Z 28 NET Z 19 DTL, Z 19 DT Z 19 DTH Z 30 DT Elegance 18 18 18 18 18 18 18 18 18 Exclusiv, Elite 24 24 24 24 24 24 24 24 24 Design 19 19 19 19 19 19 19 19 19 Weights (kg), Table 3, Heavy accessories Accessories Sun roof Towing equipment Weight 13 24 1) Sales designation – see pages 280, 281.
288 Technical data Tyres Tyre chains 3 Tyre pressure in psi/bar Not all tyres available on the market currently meet the structural requirements. We recommend that you consult a Vauxhall Authorised Repairer concerning suitable tyre makes. Tyre chains may be used on the front wheels only. These tyres have undergone special tests to establish their reliability, safety and specific suitability for Vauxhall vehicles.
Technical data (ctd.) Tyre pressure in psi/bar 289 Tyre pressure for load of up to 4 people Tyre pressure for Tyre pressure ECO1) loaded with full load up to 4 people Engine2) Tyres Front Rear Front Rear Front Rear Z 18 XE, Z 18 XER 195/65 R 153) 205/55 R 16, 215/55 R 16, 215/50 R 17, 225/45 R 17, 225/45 R 18 29/2.0 32/2.2 35/2.4 38/2.6 32/2.2 39/2.7 Z 20 NET 205/55 R 163) 35/2.4 35/2.4 – – 38/2.6 45/3.1 215/55 R 16, 215/50 R 17, 225/45 R 17, 225/45 R 18 33/2.3 33/2.3 38/2.
290 Technical data (ctd.) Tyre pressure in psi/bar Tyre pressure for load of up to 4 people Tyre pressure for full load Engine1) Tyres Front Rear Front Rear Z 28 NEL, Z 28 NET 215/55 R 162) 36/2.5 33/2.3 39/2.7 46/3.2 215/50 R 172), 225/45 R 172), 225/45 R 182) 39/2.7 35/2.4 42/2.9 49/3.4 215/55 R 163) 38/2.6 35/2.4 41/2.8 48/3.3 215/50 R 173), 225/45 R 173), 225/45 R 183) 41/2.8 36/2.5 44/3.0 51/3.5 T 115/70 R 16 (temporary spare)4) 61/4.2 61/4.2 61/4.2 61/4.
Technical data (ctd.) Tyre pressure in psi/bar 291 Tyre pressure for load of up to 4 people Tyre pressure for Tyre pressure ECO1) loaded with full load up to 4 people Engine2) Tyres Front Rear Front Rear Front Rear Z 19 DT 195/65 R 153) 205/55 R 16 33/2.3 33/2.3 – – 35/2.4 42/2.9 215/55 R 16, 215/50 R 17, 225/45 R 17, 225/45 R 18 32/2.2 32/2.2 36/2.5 36/2.5 32/2.2 39/2.7 35/2.4 35/2.4 – – 38/2.6 45/3.1 215/55 R 16, 215/50 R 17, 225/45 R 17, 225/45 R 18 33/2.3 33/2.
292 (ctd.) Technical data Tyre pressure in psi/bar Vehicles with 19-inch wheels Tyre pressure for load of up to 4 people Tyre pressure for full load Engine1) Tyres Front Rear Front Rear Z 18 XE, Z 18 XER, Z 22 YH 235/35 R 19 39/2.7 35/2.4 41/2.8 48/3.3 215/55 R 162), 225/45 R 172), 205/50 R 172) 33/2.3 33/2.3 36/2.5 44/3.0 235/35 R 19 39/2.7 35/2.4 41/2.8 48/3.3 215/55 R 162), 225/45 R 172) 33/2.3 33/2.3 36/2.5 44/3.0 205/50 R 172) 39/2.7 35/2.4 41/2.8 48/3.
Technical data Electrical system Battery Voltage 12 Volt Amp hours 55 Ah / 60 Ah 3 / 66 Ah 3 / 70 Ah 3 / 72 Ah 3 / 85 Ah 3 Battery for remote control of central locking system CR 20 32 Battery for remote control of the auxiliary heating/auxiliary ventilation AAA LR 03 293
294 Technical data Capacities (approx. litre) Engine1) Z 18 XE Z 18 XER Z 20 NET Z 22 YH Z 28 NEL Z 28 NET Fuel tank (nominal content) 60 60 60 60 60 60 Engine oil with filter change between MIN and MAX on dipstick 4.25 1.0 4.5 1.0 6.0 1.0 5.0 1.0 6.0 1.0 6.0 1.0 Windscreen wash reservoir with headlight wash system 2.9 5.6 2.9 5.6 2.9 5.6 2.9 5.6 2.9 5.6 2.9 5.6 1) Sales designation – see pages 280, 281.
Technical data Capacities (approx. litre) Engine1) Z 19 DTL Z 19 DT Z 19 DTH Z 30 DT Fuel tank (nominal content) 60 60 60 60 Engine oil with filter change between MIN and MAX on dipstick 4.3 1.0 4.3 1.0 4.3 1.0 7.5 1.0 Windscreen wash reservoir with headlight wash system 2.9 5.6 2.9 5.6 2.9 5.6 2.9 5.6 1) Sales designation – see pages 280, 281.
296 Technical data Dimensions (approx. mm) Signum Overall length 46511) Overall width 1798 Width with two exterior mirrors 2036 2) 1466 Overall height Length of luggage compartment floor Luggage compartment width maximum between the wheel arches 929 1054 978 Height of luggage compartment opening 727 Wheelbase 2830 Turning circle diameter 1) 2) 3) 3) Version with body kit. At kerb weight with driver. In metres. 11.
Technical data Installation dimensions of trailer towing equipment with removable coupling ball bar All dimensions refer to factory-fitted towing equipment. Dimension mm A 602 B 540 C 380 D 998 E 495 F 492.5 G 486.5 H 238 9 Warning Only use towing equipment approved for your vehicle. We recommend entrusting retrofitting of towing equipment to a workshop.
298 Index Index A ABS (Anti-lock Braking System) ............ 210 Accessories .......................................77, 232 Accessory socket ..................................... 94 Adaptive brake light ............................. 208 Adaptive Forward Lighting .................. 132 Bulb replacement ............................... 254 Driving abroad ................................... 136 Adaptive Forward Lighting (AFL) Bulb replacement ............................... 254 Driving abroad ...............
Index Cold start ................................................ 185 Colour information display ................... 108 Continuous Damping Control (CDC) .... 198 Contrast .................................................. 119 Control indicator ABS (Anti-lock Braking System) ........ 210 Airbag ................................................... 86 Engine electronics .............................. 192 ESP (Electronic Stability Program) .... 196 Exhaust ...............................................
300 Index Exhaust system ...................................... 193 Exterior lighting switch-off delay .......... 133 Exterior mirrors .................................40, 143 F Fan ......................................... 145, 152, 267 Filling station Capacities ...................................294, 295 Engine oil level ................................... 268 Fuel .................................... 188, 280, 281 Opening the bonnet .......................... 226 Tyre pressure .......................
Index J Jack ......................................................... 235 Jump starting ......................................... 228 K Key Extending ............................................. 26 Ignition lock ................................6, 15, 27 Locking doors ....................................... 30 Remove ................................................. 16 Starting the engine .......................... 6, 15 Keys ..........................................................
302 Index Power assisted steering, see electrohydraulic power assisted steering .... 184 Preheating .............................................. 102 Pushing, towing ..................................... 227 Q Quickheat .............................. 146, 154, 158 R Radio ...................................................... 137 Radio equipment (CB) ........................... 139 Radio reception ..................................... 137 Radio remote control Auxiliary heating .........................
Index Time ................................................110, 113 Toll systems ............................................ 138 Tools ....................................................... 235 Towing .................................................... 230 Towing equipment ................................ 219 Towing eye .....................................230, 231 Trailer Stability Assist (TSA) .................. 223 Transmission display ............................. 168 Transmission, automatic ........
304 Index
Owner’s Manual SIGNUM Operation, Safety and Maintenance Reproduction or translation, in whole or in parts, is not permitted without prior written consent from Vauxhall Motors Ltd. All rights as understood under the copyright laws are explicitly reserved by Vauxhall Motors Ltd. All information, illustrations and specifications contained in this manual are based on the latest production information available at the time of publication. The right is reserved to make changes at any time without notice.
