Owner’s Manual Model Year 2013.5 Edition: March 2013 KTA-2682/5a-VX-en 0-1 VAUXHALL Vivaro Owner’s Manual Model Year 2013.
Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 18 Seats, restraints ........................... 32 Storage ........................................ 53 Instruments and controls ............. 58 Lighting ........................................ 77 Climate control ............................. 82 Driving and operating ................... 91 Vehicle care ...............................
2 Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available under the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". Thank you for choosing a Vauxhall. We wish you many hours of pleasurable driving.
Introduction 5
6 In brief In brief Vehicle unlocking Unlocking with remote control Unlocking with key Initial drive information Turn the key in the driver's door lock. Open the doors by pulling the handles. Press button c (or press and hold) to unlock vehicle. Radio remote control 3 18, Central locking system 3 20, Load compartment 3 25.
In brief Seat adjustment 7 Seat backrests Seat height Pull lever, adjust inclination and release lever. Allow the seat to engage. Do not lean on backrest when adjusting. Seat position 3 33, Seat adjustment 3 34. Lift lever and adjust body weight on seat to raise or lower it. Seat position 3 33, Seat adjustment 3 34. Seat positioning Pull handle, slide seat, release handle. Seat position 3 33, Seat adjustment 3 34.
8 In brief Head restraint adjustment Seat belt Mirror adjustment Interior mirror Raise or lower head restraint to the desired height. Head restraints 3 32. Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25°). To release belt, press red button on belt buckle. Seat position 3 33, Seat belts 3 39, Airbag system 3 42.
In brief Exterior mirrors 9 Electric adjustment Steering wheel adjustment Select the relevant exterior mirror and adjust it. Convex exterior mirrors 3 28, Electric adjustment 3 28, Folding exterior mirrors 3 28, Heated exterior mirrors 3 29. Unlock the lever, adjust the steering wheel, then engage the lever and ensure it is fully locked. Do not adjust the steering wheel unless vehicle is stationary and the steering wheel lock has been released. Airbag system 3 42, Ignition positions 3 92.
10 In brief Instrument panel overview
In brief 1 Ashtray .................................. 63 8 Cupholders ........................... 54 2 3 4 Fuse box ............................. 126 Fixed air vents ....................... 89 Side air vents ........................ 88 Light switch .......................... 77 Rear fog light ......................... 80 Front fog lights ..................... 79 Exit lighting ............................ 81 Turn and lane-change signals ................................... 79 Sidelights ..................
12 In brief 27 Auxiliary heater ..................... 85 28 Bonnet release lever ........... 113 Exterior lighting Front and rear fog lights Turn light switch = Off 7 = Sidelights 0 9P = Headlights = Front fog lights > >r = Front and rear fog lights Turn light switch = Front fog lights > >r = Front and rear fog lights Lighting 3 77, Automatic light control 3 77, Headlight warning device 3 73.
In brief Headlight flash, high beam and low beam Pull lever. High beam 3 78, Headlight flash 3 78. Turn and lane-change signals Hazard warning flashers lever up = right turn signal lever down = left turn signal Operated with the ¨ button. Hazard warning flashers 3 79. Turn and lane-change signals 3 79.
14 Horn In brief Washer and wiper systems Windscreen wiper Press j. K = timed interval wiping 1 = slow 2 = fast Windscreen wiper 3 59, Wiper blade replacement 3 120. Windscreen and headlight washer systems Pull lever. short = wiper swipes once pull long = wiper swipes for a few pull strokes and washer fluid is sprayed onto the windscreen Windscreen and headlight washer system 3 59, Wiper blade replacement 3 120, Washer fluid 3 117.
In brief Rear window wiper and washer system Turn lever. 0 = off e = wiper f = washer Rear window wiper and washer system 3 60, Wiper blade replacement 3 120, Washer fluid 3 117. Climate control Heated rear window, heated exterior mirrors Heating is operated by pressing the Ü button. Heated exterior mirrors 3 29, Heated rear window 3 31. 15 Demisting and defrosting the windows Air distribution to V. Set temperature control to warmest level. Set fan speed to highest level. Cooling AC on.
16 In brief Transmission Manual transmission automated Manual transmission Reverse: with the vehicle stationary, wait 3 seconds after depressing clutch pedal and then pull up the collar on the selector lever and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection. Manual transmission 3 94.
In brief Starting the engine ■ Turn key to position A ■ move the steering wheel slightly to release the steering wheel lock ■ operate clutch and brake ■ do not operate accelerator pedal ■ diesel engines: turn the key to position M for preheating and wait until control indicator ! extinguishes in the Driver Information Centre. ■ turn key to position D and release. Starting the engine 3 92. Parking ■ Always apply parking brake without pushing the release button.
18 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 18 Doors ........................................... 24 Vehicle security ............................ 25 Exterior mirrors ............................ 28 Interior mirrors ............................. 29 Windows ...................................... 29 Keys, locks Keys Replacement keys The key number is specified on the key or on a detachable tag.
Keys, doors and windows The remote control has a range of approx. 5 metres. It can be restricted by external influences. The hazard warning flashers confirm operation. Handle with care, protect it from moisture and high temperatures and avoid unnecessary operation.
20 Keys, doors and windows Replace screw and tighten. Central locking system Unlocking with 2-button remote control Unlocking with 3-button remote control Depending on vehicle configuration: ■ Press button c: All doors and the load compartment are unlocked. ■ Press button c once to unlock the front doors, and press c twice to unlock all doors and the load compartment. Depending on vehicle configuration: ■ Press button c: Front doors are unlocked.
Keys, doors and windows 21 ■ Press button c: Front doors and sliding side doors are unlocked. Press and hold button c: All doors and the load compartment are unlocked. ■ Press button c: Driver's door only is unlocked. Press and hold c: All doors and the load compartment are unlocked. If no door is opened within approx. 30 seconds after the vehicle has been unlocked, the vehicle is re-locked automatically.
22 Keys, doors and windows Load compartment Locking and unlocking load compartment with 2-button remote control Locking and unlocking load compartment with 3-button remote control Press switch: e = lock y = unlock Depending on vehicle configuration: ■ Press button e or c once: Load compartment is locked or unlocked. ■ Press button e or c twice: Load compartment is locked or unlocked. Depending on vehicle configuration: ■ Press button G: Load compartment is locked or unlocked.
Keys, doors and windows Automatic locking Child locks Automatic locking after driving off This security feature can be configured to automatically lock the doors, load compartment and fuel filler flap as soon as the vehicle is driven. Activation With the ignition switched on, press and hold e on the central locking switch for approx. 5 seconds. An audible signal confirms activation. Deactivation With the ignition switched on, press and hold y on the central locking switch for approx. 5 seconds.
24 Keys, doors and windows Doors Sliding door The right hand rear door is released using the lever. Ensure the side door is fully closed and secure before driving the vehicle. The door can be locked from inside the vehicle with the interior lock switch. Rear doors To open the left hand rear door pull the outside handle. The door is opened from inside the vehicle by pulling the interior handle.
Keys, doors and windows Load compartment Central locking system 3 20. Vehicle security Tailgate Closing Close tailgate using the interior strap. Ensure tailgate is fully closed. Central locking system 3 20. Anti-theft locking system Opening General hints for operating tailgate 9 Warning Do not drive with the tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases, could enter the vehicle.
26 Keys, doors and windows Activation It monitors: ■ Doors, tailgate, bonnet ■ Passenger compartment, ■ Load compartment, ■ Vehicle inclination, e.g. if it is raised ■ Ignition ■ Interruption of alarm siren power supply. Activation All doors and the bonnet must be closed. Press button e twice. - or Turn key in driver's door lock towards rear of vehicle twice. Deactivation Unlock the doors with the key or button c on the remote control.
Keys, doors and windows deactivate the anti-theft alarm system if the vehicle battery must be disconnected. To silence the alarm siren (if triggered) and therefore deactivate the anti-theft alarm system, reconnect vehicle battery and unlock vehicle with remote control button c (or switch on the ignition). Immobiliser Press and hold button e; an audible signal will sound as confirmation. The status will remain until the doors are unlocked.
28 Keys, doors and windows Exterior mirrors Electric adjustment Folding Select the relevant exterior mirror by switching the control to the left or right, then swivel the control to adjust the mirror. No mirror is selected when the control is in the centre position. The lower mirrors are not adjustable. For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force.
Keys, doors and windows Heated Interior mirrors Windows Manual anti-dazzle Windscreen 29 Heat-reflecting windscreen The heat-reflecting windscreen has a coating which reflects solar radiation. Also data signals, e.g. from toll stations, might be reflected. Operated by pressing the Ü button. Heating functions with the engine running. It is switched off automatically after a short time. Climate control system 3 82. To reduce dazzle, adjust the lever on the underside of the mirror housing.
30 Keys, doors and windows Rear windows Windscreen stickers Do not attach stickers such as toll road stickers or similar on the windscreen in the area of the interior mirror. Sliding side windows Manual windows The door windows can be opened or closed with the window winders. Power windows 9 Warning Take care when operating the power windows. Risk of injury, particularly to children. Keep a close watch on the windows when closing them. Ensure that nothing becomes trapped in them as they move.
Keys, doors and windows Heated rear window Operated by pressing the Ü button. Heating functions with the engine running and is switched off automatically after a short time. Climate control system 3 82. Sun visors The sun visors can be folded down or swivelled to the side to prevent dazzling. If the sun visors have integral mirrors, the mirror covers should be closed when driving.
32 Seats, restraints Seats, restraints Head restraints ............................ 32 Front seats ................................... 33 Rear seats ................................... 36 Seat belts ..................................... 39 Airbag system .............................. 42 Child restraints ............................. 45 Head restraints Adjustment Position 9 Warning Only drive with the head restraint set to the proper position.
Seats, restraints Head restraint removal Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. To remove the head restraints, pull lock tab and pull the restraint upwards. Stow head restraints securely in load compartment. Do not drive with head restraints removed if the seat is occupied. ■ Sit with buttocks as far back against the backrest as possible. Adjust the distance between the seat and the pedals so that legs are slightly angled when pressing the pedals.
34 Seats, restraints Seat adjustment 9 Danger Pull handle, slide seat, release handle. Seat height Seat backrests Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat positioning Lift lever and adjust body weight on seat to adjust height. Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly. Do not lean on seat when adjusting.
Seats, restraints 35 Lumbar support Armrest Heating Adjust lumbar support using handwheel to suit personal requirements. Rotate handwheel to increase and decrease support. Adjust armrest support to suit personal requirements. ■ Raise armrest in increments to desired height. ■ To reposition, fully raise armrest before lowering. Press the ß button for the respective seat. Press the ß button again to switch off.
36 Seats, restraints Seat heating is operational when the engine is running. Rear seats Second row seats To enable long items to be stored under the seats the centre seat trim cover can be unclipped. When folding or removing the rear seat ensure the armrests are folded away in their most upright position. Also remove the lower seat trim side pocket by disconnecting it from the fixings.
Seats, restraints Rear seat access Folding seats On some variants, the cargo area can be increased by folding up the rear seats. 37 Lift and fold the seat assembly, until the seat frame rests in place. 9 Warning When folding the seat use caution - beware of moving parts. Ensure the seat is secure when completely folded. To facilitate access to the rear seats, fold the seat backrest forwards. If necessary release the two-latch seat belt from its buckles.
38 Seats, restraints Gradually lower the seat assembly, allowing the rear support legs to fold down. Lower the seat completely, ensuring the rear support legs are located, and latched. Raise the backrest, reinstall head restraints and connect the seat belts. When installing the seats, ensure that the seats are properly located on the anchor points and that the locking catches are fully engaged. Removable rear seats On some variants, the cargo area can be increased by removing the rear seats.
Seats, restraints Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the sitting position. Therefore, the risk of injury is considerably reduced. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves. Seat belts are only designed for use by one person at a time. Child restraint system 3 45.
40 Seats, restraints Three-point seat belt Height adjustment Fitting Withdraw the belt from the retractor, guide it untwisted across the body and insert the latch plate into the buckle. Tighten the lap belt regularly whilst driving by pulling the shoulder belt. Seat belt reminder 3 68. Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body.
Seats, restraints Removing Seat belts on the rear seats Two-latch belt When releasing the seat belt, ensure that the central buckle is always released before the buckle on the side of the seat. Always remove the lower latch plate from the outside buckle before removing seats from the vehicle or to facilitate access to the rear seats. Second row seats 3 36. To release belt, press red button on belt buckle.
42 Seats, restraints 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen. Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner.
Seats, restraints The front airbag system is triggered in the event of an accident of a certain severity. The ignition needs to be switched on. The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and head of the front seat occupants considerably. 43 Side airbag system 9 Warning Optimum protection is only provided when the seat is in the proper position 3 33. Keep the area in which the airbag inflates clear of obstructions.
44 Seats, restraints Curtain airbag system 9 Warning Keep the area in which the airbag inflates clear of obstructions. The airbag deactivation system is indicated by a label on the side of the instrument panel, visible when the front passenger door is open. Airbag deactivation The curtain airbag system consists of an airbag in the roof frame on each side. This can be identified by the word AIRBAG on the headlining trim.
Seats, restraints instrument cluster. A child restraint system can be installed in accordance with the installation locations chart 3 47. 9 Danger Risk of fatal injury for a child using a child restraint system together with activated front passenger airbag. Risk of fatal injury for an adult person with deactivated front passenger airbag. As long as control indicator W is not illuminated, the airbag systems for the front passenger seat will inflate in the event of a collision.
46 Seats, restraints Allow children to enter and exit the vehicle only on the side facing away from the traffic. When the child restraint system is not in use, secure the seat with a seat belt or remove it from the vehicle. Note Do not stick anything on the child restraint systems and do not cover them with any other materials. A child restraint system which has been subjected to stress in an accident must be replaced.
Seats, restraints 47 Child restraint installation locations Permissible options for fitting a child restraint system Front seats - All variants Single seat - front passenger side1) Bench seat - front passenger side without airbag with airbag Weight and age class without airbag with airbag centre outer centre outer Group 0: up to 10 kg or approx. 10 months Group 0+: up to 13 kg or approx.
48 Seats, restraints Combi - rear seats 2nd row seats Weight and age class Group 0: up to 10 kg or approx. 10 months Group 0+: up to 13 kg or approx. 2 years Group I: 9 to 18 kg or approx. 8 months to 4 years Group II: 15 to 25 kg or approx. 3 to 7 years Group III: 22 to 36 kg or approx.
Seats, restraints 49 Tour - rear seats 2nd row seats Weight and age class Group 0: up to 10 kg or approx. 10 months Group 0+: up to 13 kg or approx. 2 years Group I: 9 to 18 kg or approx. 8 months to 4 years Group II: 15 to 25 kg or approx. 3 to 7 years Group III: 22 to 36 kg or approx.
50 Seats, restraints U = Suitable for universal category restraint systems for use in this weight and age class, in conjunction with three-point seat belt. UF = Suitable for universal category forward-facing restraint systems for use in this weight and age class, in conjunction with three-point seat belt. < = Suitable for ISOFIX child restraint system with mounting brackets and anchorage points, where fitted.
Seats, restraints 51 Permissible options for fitting an ISOFIX child restraint system Weight class Size class Fixture Front seats 2nd row seats 3rd row seats Driver side outer seat Passenger side Centre outer seat Group 0: up to 10 kg E ISO/R1 X IL IL X X Group 0+: up to 13 kg E ISO/R1 X IL IL X X D ISO/R2 X IL IL X X C ISO/R3 X IL IL5) X X D ISO/R2 X IL IL X X C ISO/R3 X IL IL5) X X B ISO/F2 X IL, IUF IL, IUF X X B1 ISO/F2X X IL, IUF IL, IUF X
52 Seats, restraints Isofix child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. When using ISOFIX mounting brackets for seat mounting, universally approved child restraint systems for ISOFIX may be used. Permissible mounting location positions for ISOFIX child restraint systems are marked in the tables by <, IL and IUF. Top-tether fastening eyes Top-Tether fastening eyes are located on the back of the seat.
Storage Storage Storage compartments ................ 53 Load compartment ....................... 54 Roof rack system ......................... 56 Loading information ..................... 56 Storage compartments 53 Glovebox 9 Warning Do not store heavy or sharp objects in the storage compartments. Otherwise, the storage compartment lid could open and vehicle occupants could be injured by objects being thrown around in the event of hard braking, a sudden change in direction or an accident.
54 Storage Cupholders Overcab storage Load compartment Load compartment cover Do not place any objects on the cover. Removing Cupholders are located at either end of the instrument panel. To use cupholders remove the ashtray unit. Front storage Two coat hooks are located on the cabin bulkhead. The front door pockets contain bottle holders. The total weight in this compartment must not exceed 30 kg. Lift cover and disconnect from the side guides.
Storage Load rails and hooks Load anchorage rails mounted in the load compartment provide adjustable anchorage points for securing cargo.
56 Storage Roof rack system Loading information Roof rack ■ Heavy objects in the load compartment should be evenly distributed and placed as far forward as possible. If objects can be stacked, the heavier objects should be placed at the bottom. ■ Secure objects with lashing straps attached to lashing eyes. ■ Secure loose objects in load compartment to prevent sliding. ■ Do not place any objects on the load compartment cover or the instrument panel.
Storage ■ The payload is the difference between the permitted gross vehicle weight (see identification plate 3 147) and the EC kerb weight. To calculate the EC kerb weight, enter the data for your vehicle in the Weights table at the front of this manual. The EC kerb weight includes weights for the driver (68 kg), luggage (7 kg) and all fluids (tank 90 % full). Optional equipment and accessories increase the kerb weight.
58 Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Controls ....................................... 58 Warning lights, gauges and indi‐ cators ........................................... 63 Information displays ..................... 72 Vehicle messages ........................ 73 Trip computer ............................... 74 Tachograph ..................................
Instruments and controls Horn Windscreen wiper/washer 59 Automatic wiping with rain sensor Windscreen wiper Press j. The horn will sound regardless of ignition switch position. Steering column controls The Infotainment system can be also operated via the controls on the steering column. Further information is available in the Infotainment manual. K = automatic wiping with rain sensor K = timed interval wipe 1 = slow 2 = fast Do not use if the windscreen is frozen. Switch off in car washes.
60 Instruments and controls Adjustable sensitivity of the rain sensor Turn the adjuster wheel to adjust the sensitivity: low = turn adjuster wheel sensitivity downwards high = turn adjuster wheel sensitivity upwards Keep the sensor free from dust, dirt and ice. Windscreen washer Rear window wiper/washer Pull lever. Washer fluid is sprayed onto the windscreen.
Instruments and controls Outside temperature 9 Warning The road surface may already be icy even though the display indicates a few degrees above 0 °C. Clock A drop in temperature is indicated immediately and a rise in temperature after a time delay. If outside temperatures drop to 3 °C, the °C flashes in the information display as a warning for icy road conditions. This will continue to flash until temperatures rise above 3 °C.
62 Instruments and controls Power outlets Caution Do not damage the outlet by using unsuitable plugs. Cigarette lighter 12 V power outlets are located in the instrument panel and in the rear of the vehicle. Connecting electrical accessories while the engine is off will discharge the battery. Do not exceed the maximum power consumption of 120 watts. Do not connect any current-delivering accessories, e.g. electrical charging devices or batteries.
Instruments and controls Ashtrays Caution To be used only for ash and not for combustible rubbish. Warning lights, gauges and indicators Speedometer 63 Note Under certain conditions (e.g. steep inclines) the vehicle speed may exceed the set limit. Odometer Portable ashtray Ashtray container for mobile use in the vehicle. To use, open cover. Indicates vehicle speed. Maximum speed may be restricted by a speed regulator.
64 Instruments and controls seconds with the ignition on. The display will flash and the value will reset to zero. Tachometer Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Caution If the needle is in the red warning zone, the maximum permitted engine speed is exceeded. Engine at risk. Fuel gauge Displays fuel level in the tank. The illumination of bars corresponds to fuel level.
Instruments and controls Because of the fuel remaining in the tank, the top-up quantity may be less than the specified tank capacity. Engine oil level monitor The engine oil level monitor is correct only if the vehicle is parked on a level surface with a cold engine. If the minimum engine oil level is reached, the message OIL is displayed in the Driver Information Centre for 30 seconds after the ignition is switched on. Check and top up engine oil 3 114.
66 Instruments and controls Transmission display The mode or selected gear of the manual transmission automated is shown in the Driver Information Centre. R = Reverse gear N = Neutral A = Automatic mode kg = Laden mode V = Winter mode T = Apply foot brake W = Transmission electronics Manual transmission automated 3 95. Control indicators The control indicators described are not present in all vehicles. The description applies to all instrument versions.
Instruments and controls Control indicators in the instrument cluster 67
68 Instruments and controls Turn signal O flashes green. Flashes if a turn signal or the hazard warning flashers are activated. Rapid flashing: failure of a turn signal light or associated fuse. An audible warning can be heard when the turn signals are on. When towing a trailer, the pitch of the audible warning changes. Bulb replacement 3 121. Fuses 3 125. Turn signals 3 79. Seat belt reminder X illuminates in red. If the seat belt is not fastened, X will flash when vehicle speed exceeds approx. 10 mph.
Instruments and controls 9 Danger Risk of fatal injury for a child using a child restraint system together with activated front passenger airbag. Risk of fatal injury for an adult person with deactivated front passenger airbag. Airbag system 3 42, belt tensioners 3 39, airbag deactivation 3 44. Charging system p illuminates red. Illuminates when the ignition is switched on and goes out shortly after the engine starts. Illuminates when the engine is running Stop, switch off engine.
70 Instruments and controls If the message BRAKING FAULT appears in the Driver Information Centre there is a fault in the braking system. Seek the assistance of a workshop immediately. Brake system 3 98. Driver Information Centre. Seek the assistance of a workshop immediately. Antilock brake system 3 99. ESP®Plus 3 101. Upshift W illuminates red. Antilock brake system (ABS) k or j illuminates green. It is recommended to shift gear when illuminated to improve fuel economy. u illuminates yellow.
Instruments and controls Diesel particle filter 8 illuminates yellow. Illuminates when the diesel particle filter requires cleaning 3 93. Engine oil pressure I illuminates red. Illuminates when the ignition is switched on and goes out shortly after the engine starts. Illuminates when the engine is running Caution Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels. 1. Depress clutch. 2. Select neutral gear, set selector lever to N. 3.
72 Instruments and controls m illuminates green when a certain speed is stored. U illuminates green when the system is on. Information displays Driver Information Centre Triple-Info-Display Displays time, outside temperature and Infotainment system information. Speed limiter U illuminates yellow. U illuminates yellow when the system is on. Cruise control, Speed limiter 3 102.
Instruments and controls Vehicle messages Messages are shown in the Driver Information Centre, in combination with illumination of control indicator A or C in the instrument cluster. remains illuminated. The fault will then be stored in the on board system. Fault messages CHECK ESP Information messages CHECK FUEL FILTER Information messages CHECK GEARBOX BATTERY MODE: ECONOMY ESP OFF AUTO LIGHTS DEACTIVATED OIL LEVEL CORRECT Fault messages Will be displayed in combination with control indicator A.
74 Instruments and controls When the vehicle is parked and/ or the driver's door is opened: ■ When the key has been left in the ignition. ■ With exterior lights on. ■ If the vehicle has manual transmission automated; neutral is not selected or the foot brake has not been depressed. Engine oil level If the minimum engine oil level is reached, the message OIL is displayed in the Driver Information Centre for 30 seconds after the ignition is switched on. Check oil level 3 114.
Instruments and controls ■ ■ ■ ■ ■ Distance travelled Average speed Distance before service Clock Cruise control and speed limiter stored speed ■ Fault and information messages Fuel used Displays the amount of fuel consumed since the last reset. The measurement can be restarted at any time by pressing and holding the button. Average consumption The value is displayed after driving a distance of 0.25 miles.
76 Instruments and controls Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost. Tachograph The tachograph is operated as described in the operating instructions supplied. Observe regulations regarding use.
Lighting Lighting Exterior lighting 77 Automatic light control Light switch Exterior lighting ............................ 77 Interior lighting ............................. 80 Lighting features .......................... 81 Turn light switch: = Off 7 = Sidelights 0 9P = Headlights High beam control indicator P 3 71. Low beam control indicator 9 3 71.
78 Lighting 3. Repeat step 2 within approx. 5 seconds. 4. A double acoustic signal sounds for confirmation. Repeat the operation to deactivate. For reasons of safety, it is advisable to have the automatic light control function activated. High beam Headlight range adjustment Manual headlight range adjustment Daytime running lights Daytime running lights increase visibility of the vehicle during daylight. The lights operate automatically when the ignition is switched on.
Lighting Headlights when driving abroad The asymmetrical headlight beam extends visibility at the edge of the road at the passenger side. However, when driving in countries where traffic drives on the opposite side of the road, adjust the headlights to prevent dazzling of oncoming traffic. Have the headlights adjusted by a workshop. Operated with the ¨ button. Turn and lane-change signals 79 When lane changing, move lever part way to first stop. When released, lever will spring back.
80 Lighting Rear fog lights Turn inner switch to position >r. Rear fog light comes on in conjunction with front fog lights and will only operate when the ignition and headlights are switched on. Interior lighting Interior lights Load compartment lighting Load compartment lighting can be set to illuminate when the side and rear doors are opened, or switched on constantly. Reversing lights The reversing lights come on when the ignition is on and reverse gear is selected.
Lighting Operated by tilting the lens to one of 3 positions, i.e.: ■ On ■ Controlled by the function of the front interior light ■ Off When the front interior light is functioning as a courtesy light, move the lens of the load compartment light to its central position; the load compartment light functions as a courtesy light and also illuminates when the side or rear doors are opened. When the doors are closed, the courtesy light extinguishes after approx.
82 Climate control Climate control Climate control systems ............... 82 Air vents ....................................... 88 Maintenance ................................ 89 Climate control systems Heating and ventilation system Heating will not be fully effective until the engine has reached normal operating temperature. Fan speed Adjust the air flow by switching the fan to the desired speed.
Climate control ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J. Air conditioning system Cooling (AC) Operated with the AC button and functional only when the engine and fan are running. The air conditioning system cools and dehumidifies (dries) the air when outside temperature is a little above the freezing point. Therefore condensation may form and drip from under the vehicle.
84 Climate control Rear heating system The rear passenger compartment heating fan assists air flow to the rear passenger compartment via the rear air vents. Note Country-specific version: Heating will cease to operate if the vehicle fuel level drops below 11 litres. Rear air conditioning fan switch The rate of air flow is determined by the fan. Air temperature is controlled using the temperature control on the instrument panel.
Climate control Auxiliary heater Coolant heater The Eberspächer engineindependent, fuel-powered coolant heater provides rapid heating of the engine coolant to enable heating of the vehicle interior without the engine running. 9 Warning Do not operate the system when refuelling, when dust or combustible vapours are present or in enclosed spaces (e.g. garage). Before starting or programming the system to start, turn the vehicle's climate control system to heat and the air distribution to V.
86 Climate control The control buttons operate identically to the timer unit described previously. To activate the remote control, press activation button X and release it when the menu bar appears in the display. The signal indicator and SENd appear briefly in the display, followed by the temperature. Dispose of old batteries in accordance with environmental regulations.
Climate control Teach remote control If the vehicle battery is reconnected, the LED in the instrument panel button illuminates and the system configures the remote control menu automatically. If the LED flashes, press OK button on remote control, select Add or AddE and confirm. Additional remote control units may also be configured. Press the button until LED flashes, switch on the remote control, select Add and confirm.
88 Climate control desired heating level (ECO or HIGH). The system starts automatically between 5 and 60 minutes prior to the programmed departure time. Set weekday, time and heating duration Ö If the vehicle battery is disconnected or its voltage is too low, the unit will need to be reset.
Climate control 9 Warning Do not attach any objects to the slats of the air vents. Risk of damage and injury in case of an accident. Fixed air vents Additional air vents are located beneath the windscreen and door windows and in the foot wells. Rear passenger compartment air vents The air flow is biased towards the central and right hand air vents for optimum distribution.
90 Climate control Service For optimal cooling performance, it is recommended that the climate control system be checked annually, starting three years after initial vehicle registration, including: ■ Functionality and pressure test ■ Heating functionality ■ Leakage check ■ Check of drive belts ■ Cleaning of condenser and evaporator drainage ■ Performance check
Driving and operating Driving and operating Driving hints ................................. 91 Starting and operating ................. 91 Engine exhaust ............................ 93 Manual transmission .................... 94 Manual transmission automa‐ ted ................................................ 95 Brakes .......................................... 98 Ride control systems ................. 100 Cruise control ............................. 102 Object detection systems ........... 105 Fuel ......
92 Driving and operating Ignition switch positions Starting the engine St = Ignition off A = Steering wheel lock released, ignition off M = Ignition on. Diesel engines: preheating D = Starting Manual transmission: operate clutch. Manual transmission automated: operate brake; transmission automatically shifts to N. Do not accelerate. Diesel engines: turn the key to position M for preheating until control indicator ! extinguishes from the Driver Information Centre. Turn key to position D and release.
Driving and operating uphill slopes. Operate the foot brake at the same time to reduce operating force. ■ Switch off the engine and ignition. Turn the steering wheel until the steering wheel lock is felt to engage. ■ If the vehicle is on a level surface or uphill slope, engage first gear before switching off the ignition. On an uphill slope, turn the front wheels away from the kerb. If the vehicle is on a downhill slope, engage reverse gear before switching off the ignition.
94 Driving and operating the starter, running the fuel tank dry and starting the engine by pushing or towing. In the event of misfiring, uneven engine running, a reduction in engine performance or other unusual problems, have the cause of the fault rectified by a workshop as soon as possible. In an emergency, driving can be continued for a short period, keeping vehicle speed and engine speed low. If control indicator Z flashes, the permitted emission limits may be exceeded.
Driving and operating Manual transmission automated This transmission permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control. Transmission display Starting the engine Depress the foot brake when starting the engine. If the foot brake is not depressed, T illuminates in the transmission display and the engine cannot be started.
96 Driving and operating released. To start off quickly, release the foot brake and accelerate immediately after engaging a gear. In automatic mode the transmission shifts to other gears automatically, dependent on driving conditions. To engage manual mode, move the selector lever towards A/M. The current gear will appear in the transmission display. To engage first gear, depress foot brake and move selector lever towards + or -. Shift to a higher or lower gear by moving selector lever to + or -.
Driving and operating If engine speed is too low, the transmission automatically shifts to a lower gear. If engine speed is too high, the transmission only switches to a higher gear via kickdown. Electronic driving programmes Winter mode V Activate the Winter mode if you have problems starting off on a slippery road surface. Activation Press the V button. V is shown in the transmission display. The transmission switches to automatic mode and the vehicle starts off in a suitable gear.
98 Driving and operating Deactivation The Laden mode is switched off by: ■ pressing the kg button again, ■ turning off the ignition. Kickdown If the accelerator pedal is pressed past the pressure point, the transmission shifts to a lower gear depending on engine speed. Full engine power is available for acceleration. If engine speed is too high the transmission switches to a higher gear, even in manual mode. Without kickdown this automatic shift is not effected in manual mode.
Driving and operating Control indicator R 3 69. Vehicle messages 3 73. Antilock brake system Antilock brake system (ABS) prevents the wheels from locking. ABS starts to regulate brake pressure as soon as a wheel shows a tendency to lock. The vehicle remains steerable, even during hard braking. ABS control is made apparent through a pulse in the brake pedal and the noise of the regulation process.
100 Driving and operating Brake assist If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied (full braking). Maintain steady pressure on the brake pedal for as long as full braking is required. Maximum brake force is automatically reduced when the brake pedal is released.
Driving and operating Press the v button. Control indicator v illuminates in the instrument cluster and the message ESP OFF appears in the Driver Information Centre. TC is reactivated by pressing the v button again. Control indicator v extinguishes in the instrument cluster. TC is also reactivated the next time the ignition is switched on. When vehicle speed reaches 30 mph the TC function will be restored automatically.
102 Driving and operating Press the v button. Control indicator v illuminates in the instrument cluster and the message ESP OFF appears in the Driver Information Centre. ESP®Plus is reactivated by pressing the v button again. Control indicator v extinguishes in the instrument cluster. ESP®Plus is also reactivated the next time the ignition is switched on. When vehicle speed reaches 30 mph the ESP®Plus function will be restored automatically.
Driving and operating 103 Increase speed With cruise control active, the vehicle speed can be increased continuously or in small increments by holding down or tapping switch < repeatedly. When the switch is released the current speed is stored and maintained. Alternatively, accelerate to the desired speed and store by pressing switch <. Accelerate to the desired speed and press switch < or ]. The current speed is now stored and maintained and the accelerator pedal can be released.
104 Driving and operating Deactivation Resume stored speed Activation Press switch R at a speed above 20 mph. If the stored speed is much higher than the current speed, the vehicle will accelerate powerfully until the stored speed is obtained. Deleting the stored speed Press switch m: Green control indicators U and m extinguish in the instrument cluster. Press switch §: cruise control is deactivated and the green control indicator U extinguishes in the instrument cluster.
Driving and operating Where the limit speed cannot be maintained, e.g. when driving on a steep decline, the limit speed will flash in the Driver Information Centre. Increase limit speed The limit speed can be increased continuously or in small increments by holding down or tapping switch < repeatedly. Reduce limit speed The limit speed can be decreased continuously or in small increments by holding down or tapping switch ] repeatedly.
106 Driving and operating Note Attached parts in the detection area cause system malfunction. Deactivation Permanent deactivation Permanently deactivate the system by pressing and holding the E button on the instrument panel for approx. 3 seconds with the ignition on and reverse gear engaged. The system is deactivated and will not operate. When reverse gear is selected no acoustic signal will sound, indicating deactivation. The function is reactivated by pressing and holding button E for approx.
Driving and operating Caution When reversing, the area should be free from obstacles which could impact on the underside of the vehicle. Impact to the rear axle, which may not be visible, could lead to uncharacteristic changes in the vehicle handling. In the event of such an impact, consult a workshop. Fuel 107 Caution Fuel for petrol engines Only use unleaded fuel that complies with European standard EN 228 or E DIN 51626-1 or equivalent.
108 Driving and operating Caution Use of fuel that does not comply to EN 590 or similar can lead to engine powerloss, increased wear or engine damage and may affect your warranty. Do not use marine diesel oils, heating oils, Aquazole and similar dieselwater emulsions. Diesel fuels must not be diluted with fuels for petrol engines. Refuelling 9 Danger Before refuelling, switch off engine and any external heaters with combustion chambers (identified by sticker on fuel filler flap).
Driving and operating ■ Reposition left front seat to access the release cover. ■ Remove the release cover and position the seat belt to one side. ■ Raise fuel filler release to unlock the fuel filler flap. To open To close ■ Close the fuel filler flap and lower fuel filler release to lock the fuel filler flap. ■ Replace the release cover. ■ Reposition left front seat. If the cause of the interruption to the power supply is not a discharged battery, consult a workshop.
110 Driving and operating Towing General information Only use towing equipment that has been approved for your vehicle. Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment. Driving characteristics and towing tips In the case of trailers with brakes, attach the breakaway stopping cable. Before attaching a trailer, lubricate the coupling ball.
Driving and operating in the case of heavy trailers. The vertical coupling load should never fall below 25 kg. In the case of trailer loads of 1200 kg or more, the vertical coupling load should not be less than 50 kg. Rear axle load When the trailer is coupled and the towing vehicle fully loaded (including all occupants), the permissible rear axle load (see identification plate or vehicle documents) must not be exceeded.
112 Vehicle care Vehicle care General Information ................... 112 Vehicle checks ........................... 113 Bulb replacement ....................... 121 Electrical system ........................ 125 Vehicle tools .............................. 128 Wheels and tyres ....................... 128 Towing ....................................... 138 Appearance care .......................
Vehicle care ■ ■ ■ ■ Fill up the washer fluid reservoir. Check the engine oil level. Check the coolant level. Fit the number plate, if necessary. End-of-life vehicle recovery Information on end-of-life vehicle recovery centres and the recycling of end-of-life vehicles is available on our website. Only entrust this work to an authorised recycling centre. Vehicle checks Bonnet Performing work Opening 113 9 Warning Only perform engine compartment checks when the ignition is off.
114 Vehicle care Closing Before closing the bonnet, press the support into the holder. Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged. Caution It is the owner's responsibility to maintain the proper level of an appropriate quality oil in the engine. Engine oil Pull the safety catch and open the bonnet. Secure the bonnet support. Check the engine oil level manually on a regular basis to prevent damage to the engine.
Vehicle care For M9R engines, rotate cap anticlockwise, remove the dipstick, wipe it clean and re-insert it as far as it will go. When the engine oil level has dropped to the "add oil" mark A, top up engine oil. 115 The engine oil level must not exceed the maximum mark B on the dipstick. Caution Overfilled engine oil must be drained or suctioned out. Caution On F9Q engines, the dipstick is mounted on the oil filler cap which must be rotated anticlockwise to open.
116 Vehicle care Capacities 3 157, Engine oil level monitor 3 65. Fit the cap on straight and tighten it. If the red tell-tale is displayed when the engine is running, consult a workshop. Engine air filter Engine coolant Engine air flow indicator The coolant provides freeze protection down to approx. -28 °C. Caution Only use approved antifreeze. Remove the caps and ensure funnel is securely located onto the filler pipe. Ensure the funnel is replaced securely together with both end caps fitted.
Vehicle care If the cooling system is cold, the coolant level should be just above the MIN mark. Top up if the level is low. concentration checked and have the cause of the coolant loss remedied by a workshop. If a substantial amount of coolant is required, it will be necessary to bleed any trapped air from the cooling system. Seek the assistance of a workshop. If the coolant temperature is too high, control indicator W illuminates red in the instrument cluster, together with C 3 70.
118 Vehicle care Battery Caution The vehicle battery is maintenancefree provided that the driving profile allows sufficient charging of the battery. Short-distance driving and frequent engine starts can discharge the battery. Avoid the use of unnecessary electrical consumers. Only washer fluid with a sufficient antifreeze concentration provides protection at low temperatures or a sudden drop in temperature. Brakes A squealing noise indicates that the brake lining is at its minimum thickness.
Vehicle care Battery access The battery is located beneath the front left hand seat floor panel 3 136. Warning label ■ The battery contains sulfuric acid which could cause blindness or serious burn injuries. ■ See the Owner’s Manual for further information. ■ Explosive gas may be present in the vicinity of the battery. Battery maintenance 9 Danger 119 We recommend that you have the battery replaced by a workshop.
120 Vehicle care Place a container underneath the filter housing. Loosen the knurled screws on the filter cover and on the lower part of the filter by approx. one turn, to drain off the water. The filter is drained as soon as diesel fuel emerges from the knurled screw at the bottom. Retighten the two screws. Check diesel fuel filter at shorter intervals if the vehicle is subjected to extreme operating conditions.
Vehicle care Bulb replacement Switch off the ignition and turn off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. Headlights Low beam and high beam 1. Remove harness connector. 2. Remove rubber seal. 3. Release retaining clip and remove bulb. 4. Renew bulb and install retaining clip ensuring that bulb is in correct orientation. 5. Install rubber seal and harness connector.
122 Vehicle care Front turn signal lights Tail lights Rear brake, turn signal and tail lights 1. Remove bulb holder from reflector housing by rotating through 90°. 2. Renew bulb. 3. Install bulb holder in reflector housing. 1. Remove 3 screws (using the tool supplied). 2. Carefully pull lamp assembly from retaining pins on the outer side and remove. 3. Twist bulb holder to separate from lamp assembly. 4. Renew bulb. 5. Push to install the bulb holder into the lamp assembly - then twist to secure. 6.
Vehicle care Side turn signal lights 1. Release clips from wing using a flat blade screwdriver and lift out lamp assembly from aperture. 2. Remove bulb holder from lamp assembly by rotating through 90° and renew bulb. 3. Install bulb holder in lamp assembly and install lamp assembly into aperture. Centre high-mounted brake light Have bulbs replaced by a workshop. Reversing light 1. Remove 2 screws (using the tool supplied) and remove lamp assembly. 2. Twist bulb housing to separate from lamp assembly.
124 Vehicle care Fog tail light Interior lights Load compartment light Front courtesy light 1. Remove 2 screws (using the tool supplied) and remove lamp assembly. 2. Twist bulb housing to separate from lamp assembly. 3. Renew bulb. 4. Push to install the bulb holder into the lamp assembly - then twist to secure. 5. Install lamp assembly with 2 screws. 1. Remove lens using a flat blade screwdriver. 2. Renew bulb. 3. Reinstall lens assembly. 1. Remove lamp assembly using a flat blade screwdriver. 2.
Vehicle care Instrument panel illumination Have bulbs replaced by a workshop. 125 Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. The fuse box is located on the lefthand side of the instrument panel, below the cupholder. Before replacing a fuse, turn off the respective switch and the ignition. A blown fuse can be recognised by its melted wire. Do not replace the fuse until the cause of the fault has been remedied.
126 Vehicle care Instrument panel fuse box Fuse extractor To help in replacing fuses, a fuse extractor is located in the fuse box. Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse. Located on the left-hand side of the instrument panel, below the cupholder. Remove the ashtray from the lefthand cup holder and pull open the fuse box cover. Do not store any objects behind the cover. Some circuits may be protected by several fuses.
Vehicle care Symbol Application Symbol Application Symbol Application Z Air conditioning u Antilock brake system ? Power outlet d Heated exterior mirrors Ü Heated rear windows T Tachograph U Heated front seats + , Power windows Clock, interior lights, radio, Infotainment system L Left-hand high beam Fuel injection system N Right-hand high beam UCH INJ K Windscreen wiper f Rear window washer Z Radio, Infotainment system e Rear widow wiper ) Cigarette lighter T Left-hand
128 Vehicle care Vehicle tools Tools Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage. Seek the assistance of a workshop in the event of damage or unusual wear.
Vehicle care Tyre pressure Check the pressure of cold tyres at least every 14 days and before any long journey. Do not forget the spare wheel. Tyre pressures 3 157. The tyre pressure data refers to cold tyres. It applies to summer and winter tyres. Always inflate the spare tyre to the pressure specified for full load. Incorrect tyre pressures will impair safety, vehicle handling, comfort and fuel economy and will increase tyre wear.
130 Vehicle care Wheel covers Tyre chains Wheel covers and tyres that are factory approved for the respective vehicle and comply with all of the relevant wheel and tyre combination requirements must be used. If the wheel covers and tyres used are not factory approved, the tyres must not have a rim protection ridge. Wheel covers must not impair brake cooling. Tyre repair kit 9 Warning Use of unsuitable tyres or wheel covers could lead to sudden pressure loss and thereby accidents.
Vehicle care 9 Warning Do not drive faster than 50 mph. Do not use for a lengthy period. Steering and handling may be affected. 2. Remove the electrical connection cable and air hose from the compartments on the underside of the compressor. If the vehicle has a flat tyre: Apply the parking brake and engage first gear or reverse gear. The tyre repair kit is located under the front seat. 1. Remove the compressor from the tyre repair kit. 131 3.
132 Vehicle care 9. Set the rocker switch on the compressor to I. The tyre is filled with sealant. 10. The compressor pressure gauge briefly indicates up to 6 bar (600 kPa/87 psi). Then the pressure starts to drop. 11. All of the sealant is pumped into the tyre. Then the tyre is inflated. 12. The prescribed tyre pressure should be obtained within 10 minutes. Tyre pressure 3 157. When the correct pressure is obtained, switch off the compressor.
Vehicle care the vehicle must not be driven. Seek the assistance of a workshop. 18. Stow tyre repair kit under the front seat. 9 Warning Do not allow the sealant to contact skin, eyes or clothing. If swallowed seek medical assistance immediately. 16. Continue driving immediately so that the sealant is evenly distributed throughout the tyre. After driving approx. 6 miles, but no more than 10 minutes, stop and check tyre pressure using the compressor.
134 Vehicle care ■ Never change more than one wheel at a time. ■ Use the jack only to change wheels in case of puncture, not for a seasonal winter or summer tyre change. ■ If the ground on which the vehicle is standing is soft, a solid board (max. 1 cm thick) should be placed under the jack. ■ No people or animals may be in the vehicle when it is jacked-up. ■ Never crawl under a jacked-up vehicle. ■ Do not start the engine when the vehicle is raised on the jack. 1. Pull off the wheel cover 3 128. 2.
Vehicle care Put wheel bolts somewhere where the threads will not be soiled. 6. Change the wheel. 7. Screw in the wheel bolts. 8. Lower vehicle. 9. Tighten each wheel bolt in a crosswise sequence. Tightening torque is 140 Nm. 10. Refit wheel cover 11. Change the wheel. 12. Stow the replaced wheel 3 135 and the vehicle tools 3 128. 13. Have the new wheel balanced on the vehicle. Check the tyre pressure of the installed tyre 3 157 and also the wheel bolt torque as soon as possible.
136 Vehicle care Summer and winter tyres If you use winter tyres, the spare wheel may still be fitted with a summer tyre. If you use the spare wheel when it is fitted with a summer tyre the vehicle's driveability may be affected, especially on slippery road surfaces. Directional tyres Fit directional tyres such that they roll in the direction of travel. The rolling direction is indicated by a symbol (e.g. an arrow) on the sidewall.
Vehicle care Battery access The battery is located beneath the front left hand seat floor panel. Lift the floor covering and use the tool supplied in the tool kit (or the tyre repair kit) to loosen the 4 screws. Note the position of the arrow facing forwards on the battery cover when replacing. Remove cover plate to access the battery. Jump starting procedure 137 Lead connection order: 1. Connect the red lead to the positive terminal of the booster battery. 2.
138 Vehicle care 2. After 5 minutes, start the other engine. Start attempts should be made for no longer than 15 seconds at an interval of 1 minute. 3. Allow both engines to idle for approx. 3 minutes with the leads connected. 4. Switch on electrical consumers (e.g. headlights, heated rear window) of the vehicle receiving the jump start. 5. Reverse above sequence exactly when removing leads. Towing Towing the vehicle Caution Do not tow the vehicle from the rear.
Vehicle care Caution Towing another vehicle Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. When the engine is not running, considerably more force is needed to brake and steer. To prevent the entry of exhaust fumes from the towing vehicle, switch on the air recirculation system and close the windows. Seek the assistance of a workshop. After towing, unscrew the towing eye. 139 Vehicles with a towing hitch have a socket for the detachable towing eye.
140 Vehicle care Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only when absolutely necessary, as this has a degreasing effect and impairs lock function. After using de-icing agent, have the locks regreased by a workshop. Washing The paintwork of your vehicle is exposed to environmental influences. Wash and wax your vehicle regularly. When using automatic vehicle washes, select a programme that includes waxing.
Vehicle care Windows and windscreen wiper blades Use a soft lint-free cloth or chamois leather together with window cleaner and insect remover. When cleaning the rear window, make sure the heating element inside is not damaged. For mechanical removal of ice, use a sharp-edged ice scraper. Press the scraper firmly against the glass so that no dirt can get under it and scratch the glass. Clean smearing wiper blades with a soft cloth and window cleaner. Wheels and tyres Do not use high-pressure jet cleaners.
142 Vehicle care The instrument panel should only be cleaned using a soft damp cloth. Clean fabric upholstery with a vacuum cleaner and brush. Remove stains with an upholstery cleaner. Clothing fabrics may not be colourfast. This could cause visible discolourations, especially on lightcoloured upholstery. Removable stains and discolourations should be cleaned as soon as possible. Clean seat belts with lukewarm water or interior cleaner.
Service and maintenance Service and maintenance General information ................... 143 Recommended fluids, lubricants and parts .................................... 144 General information Service information In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified. The detailed, up-to-date service schedule for the vehicle is available at the workshop.
144 Service and maintenance The service display, located in the Driver Information Centre, indicates when the next service is due. Seek the assistance of a workshop. Service display 3 65. Engine oil level monitor 3 65. Recommended fluids, lubricants and parts Recommended fluids and lubricants Only use products that meet the recommended specifications. Damage resulting from the use of products not in line with these specifications will not be covered by the warranty.
Service and maintenance Additional engine oil additives The use of additional engine oil additives could cause damage and invalidate the warranty. Engine oil viscosity grades The SAE viscosity grade gives information of the thickness of the oil. Multigrade oil is indicated by two figures, e.g. SAE 5W-30. The first figure, followed by a W, indicates the low temperature viscosity and the second figure the high temperature viscosity.
146 Technical data Technical data Vehicle identification .................. 146 Vehicle data ............................... 148 Vehicle identification Vehicle Identification Number The VIN is also displayed behind a removable plastic cover on the right hand side door step. The Vehicle Identification Number is visible through the windscreen.
Technical data Identification plate The identification plate is located on the right hand door pillar. 1) Information on identification plate1): 1 = Manufacturer, type approval number 2 = Vehicle Identification Number 3 = Permissible gross vehicle weight rating 4 = Permissible gross combination weight 5 = Maximum permissible front axle load 6 = Maximum permissible rear axle load 7 = Vehicle-specific or country specific data The VIN plate on your vehicle may differ from the illustration shown.
148 Technical data Vehicle data Recommended fluids and lubricants Required engine oil quality Engine oil quality dexos 2 ✔ In case dexos quality is unavailable in International countries you may use the oil qualities listed below: Engine oil quality GM-LL-A-025 petrol engines ✔ GM-LL-B-025 diesel engines ✔ ACEA A3/B3 petrol engines ✔ ACEA A3/B4 diesel engines without DPF ✔ ACEA C3 diesel engines with DPF ✔
Technical data Engine oil viscosity grades Ambient temperature Petrol and diesel engines down to -25 °C SAE 5W-30 or SAE 5W-40 below -25 °C SAE 0W-30 or SAE 0W-40 Engine data Sales designation 2.0 1.9 2.
150 Technical data Sales designation 2.0 1.9 2.0 F4R 820 F9Q 760 M9R 630 2) M9R 692 Engine identifier code possible 98 possible 913) Sales designation Engine identifier code 2.0 M9R 2.
Technical data 151 Vehicle weight Kerb weight, basic model Model Wheelbase Roof Payload Class Engine Kerb weight6)7) Van Short Standard 1000 F4R 1660 F9Q 1660 M9R 1678 F4R 1660 F9Q 1669 M9R 1688 F4R 1695 F9Q 1713 M9R 1760 Standard High 6) 7) 1200 1200 Kerb weight and gross vehicle weight increase on models fitted with bad road equipment package - refer to VIN plate. Minimum vehicle weight according to Type Approval, including all fluids, vehicle tools and a 90% fuel load.
152 Technical data Model Wheelbase Roof Payload Class Engine Kerb weight6)7) Van Long Standard 1200 F4R 1660 F9Q 1676 M9R 1724 F4R 1745 F9Q 1761 M9R 1810 High 6) 7) 1200 Kerb weight and gross vehicle weight increase on models fitted with bad road equipment package - refer to VIN plate. Minimum vehicle weight according to Type Approval, including all fluids, vehicle tools and a 90% fuel load. Excludes the weight of the driver and deletable options, e.g.
Technical data Model Wheelbase Roof Payload Class Engine Kerb weight6)7) Combi Short Standard 1000 F4R 1818 F9Q 1835 M9R 1883 F4R 1829 F9Q 1846 M9R 1893 F4R 1890 F9Q 1906 M9R 1954 Standard Long 6) 7) Standard 1200 1200 153 Kerb weight and gross vehicle weight increase on models fitted with bad road equipment package - refer to VIN plate. Minimum vehicle weight according to Type Approval, including all fluids, vehicle tools and a 90% fuel load.
154 Technical data Model Wheelbase Roof Payload Class Engine Kerb weight6)7) Platform cab Long Standard 1200 F4R 14498) F9Q 14678) M9R 15158) F4R 1879 F9Q - M9R 1944 Tour 6) 7) 8) Short Standard 900 Kerb weight and gross vehicle weight increase on models fitted with bad road equipment package - refer to VIN plate. Minimum vehicle weight according to Type Approval, including all fluids, vehicle tools and a 90% fuel load.
Technical data Vehicle dimensions Type Van Combi/Tour9) Platform cab Wheelbase Short Long Short Long Long Length [mm] 4782 5182 4782 5182 5130 Width without exterior mirrors [mm] 1904 1904 1904 1904 1904 Width with two exterior mirrors [mm] 2232 2232 2232 2232 2232/243410) Height - unladen (without antenna) [mm]11) Standard roof 1968 1968 1968 1968 1981 High roof 2492 2492 - - - Wheelbase [mm] 3098 3498 3098 3498 3498 Track width [mm] Front 1615 1615 1615 1
156 Technical data Loadspace dimensions Van Wheelbase Short Long Roof height Standard High Standard High Maximum rear door aperture height [mm] 1335 1818 1335 1818 Rear door aperture width (at floor) [mm] 1390 1390 1390 1390 Maximum load area height [mm] 1387 1913 1387 1913 Maximum load area width [mm] 1690 1690 1690 1690 Width between wheel arches [mm] 1268 1268 1268 1268 Maximum load floor length [mm] 2400 2400 2800 2800 Loading height unladen [mm] 543 547 542 5
Technical data Capacities Engine oil Engine F4R F9Q M9R Engine oil including filter [l] 5.4 4.7 7.7 between MIN and MAX [l] 1.5 - 2.0 1.5 - 2.0 1.5 - 2.0 Fuel tank Fuel tank, nominal capacity [l] 92 Tyre pressures Tyre Tyre pressure with full load12) Front [kPa/bar] (psi) Rear [kPa/bar] (psi) 195/65 R16 C 340/3.4 (49) 370/3.7 (54) 195/75 R16 C 380/3.8 (55) 420/4.2 (61) 205/65 R16 C 380/3.8 (55) 420/4.2 (61) 215/65 R16 C 310/3.1 (45) 340/3.
158 Customer information Customer information Vehicle data recording and pri‐ vacy ........................................... 158 Vehicle data recording and privacy Event data recorders Data storage modules in the vehicle A large number of electronic components of your vehicle contain data storage modules temporarily or permanently storing technical data about the condition of the vehicle, events and errors.
Customer information When using the vehicle, situations may occur in which these technical data related to other information (accident report, damages on the vehicle, witness statements etc.) may be associated with a specific person possibly, with the assistance of an expert. Additional functions contractually agreed upon with the client (e.g. vehicle location in emergency cases) allow the transmission of particular vehicle data from the vehicle.
160 Index A Accessories and vehicle modifications .......................... 112 Adjustable air vents ..................... 88 Airbag and belt tensioners ........... 68 Airbag deactivation ................ 44, 68 Airbag system .............................. 42 Air conditioning regular operation 89 Air conditioning system ................ 83 Air intake ...................................... 89 Air vents........................................ 88 Alert..............................................
161 Convex shape .............................. 28 Coolant....................................... 116 Coolant and antifreeze............... 144 Coolant heater.............................. 85 Coupling ball bar........................ 111 Cruise control ...................... 71, 102 Cupholders .................................. 54 Curtain airbag system .................. 44 D Danger, Warnings and Cautions . . . 3 Dashboard.................................... 10 Daytime running light....................
162 I Identification plate ..................... 147 Ignition switch positions ............... 92 Immobiliser .................................. 27 Indicators...................................... 63 Information displays...................... 72 Instrument panel fuse box ......... 126 Instrument panel illumination ..... 125 Instrument panel overview ........... 10 Instrument panel storage.............. 53 Interior care ............................... 141 Interior lights ........................
163 Rear window wiper/washer .......... 60 Recommended fluids and lubricants ........................ 144, 148 Refuelling ................................... 108 Remote control............................. 18 Reversing light ........................... 123 Reversing lights ........................... 80 Roof rack ..................................... 56 S Safety belts................................... 39 Safety net .................................... 55 Seat adjustment .......................
164 Vehicle messages ....................... 73 Vehicle security............................ 25 Vehicle specific data ...................... 3 Vehicle storage........................... 112 Vehicle tools............................... 128 Vehicle unlocking ........................... 6 Vehicle weight ........................... 151 Ventilation..................................... 82 W Warning chimes ........................... 73 Warning lights............................... 63 Warning triangle ..........
