User Guide Vax Careline: AU: 1300 361 505 NZ: 0800 800 900 Wash n Dry Canister Get Cleaning... What’s your Vax’s model number? 3 0 0 0 0 What’s your serial number? (Located on the base of the machine) Note these down in case you need them in future. Please keep instructions for further use. vax.com.
Vax Service line: AU: 1300 361 505 NZ: 0800 800 900 vax
1 2 10 3 11 9 4 13 12 5 14 8 15 7 6 18 19 AAA 505 900 Machine Overview AN TI A LL ER G E N 17 ADD I TIVE 16 24 22 21 20 23 Fig.1/1 1 2 3 4 5 6 7 8 9 10 11 12 Water pump button (green) Power button (red) Carry handle Power cord Container release clips Casters Suction hose connection port Solution tube port Exhaust filter Hose Solution tube Suction hose connector vax.com.
General Safety Information FOR HOUSEHOLD USE ONLY. When using the vacuum cleaner, basic safety precautions should always be observed, including the following: 1. Do not leave the multifunction machine unattended when plugged in. Unplug it from the socket when not in use. 2. To prevent electric shock do not use outdoors. 3. Not to be used as a toy. 4. Children should be supervised to ensure that they do not play with the appliance. 5.
05 900 Operation Dry Vacuuming IMPORTANT: Always remove the power plug from the wall outlet before assembling, servicing or removing accessories. IMPORTANT: Only the red power button should be “ON” when the machine is in dry vacuuming mode. The green pump button should be “OFF”. Unclip Container Release Clips (A) on both sides of machine. Remove the motor top from the unit, turn on its side and remove the float housing in an anti-clockwise direction to unscrew.
Operation Dry Vacuuming Continued Insert the flexible hose into the inlet on the main body of the vacuum cleaner. Push in and twist clockwise a quarter turn until tight. Push the extension tubes onto the end of the handle. Fit the combination floor tool by pushing on to the extension tube. On/Off Button Carpet Cleaning Hard Floor Cleaning Fully unwind the power cord and plug the cord into the electrical outlet.
505 900 Operation Accessories The accessories can be attached directly to the handle by removing the extension tubes and pushing in the desired accessory. The accessories can also be attached to the extension tubes for extra reach. Remove the combination floor tool and push on the desired accessory. Crevice Tool: for crevices, corners, cracks etc. Dusting Brush: for delicate surfaces. Upholstery Tool: for carpet, upholstery, stairs etc. vax.com.
Operation Preparing the Carpet for Washing IMPORTANT: Do not use the cleaner as a dry vacuum when set up in carpet washing mode. 1. Dry vacuum carpet thoroughly. 2. Remove as much furniture from the room as possible. If unable to remove the furniture, place plastic or foil under and around the legs until the carpet has dried completely. Helpful hints for cleaning carpet: 1. Only use Vax recommended solution with this machine. 2. Do not oversaturate carpet with cleaning solution while using the machine. 3.
505 900 Operation Getting Ready to Wash Unclip Container Release Clips (A) on both sides of machine. Lift off motor container and remove filter assembly. Remove the plug from the solution intake port and replace the solution connector tube. The machine can be used for washing by placing the clean water tank (A) back inside the dirty water tank (B). Remove clean water tank (A) from inside the dirty water tank and fill with warm (max 40°C) water to point indicated on the tank.
Operation Assembly Push solution tube connector (A) firmly into solution port (A1). Twist solution tube connector (A) a quarter turn to the right to lock into place. Push hose connector (B) firmly into hose connection port (B1). Twist to the right until hose connector locks into place. Push one end of the extension tube into the handle of the hose. Wrap solution tube (A) around hose (B). Ensure that the solution tube is wrapped loosely enough to allow the solution to flow freely through the tube.
505 900 Operation Usage 1. Plug in machine to power supply. 2. Press the red button to turn on the power. 3. Press the green button to activate the pump. Washing Carpets 1. On the Fibreflow wash head ensure that the rocker switch (A) is towards the back of the head to allow water to flow through the head. 2. With the solution flowing, wash a section of carpet approx. 3 metres x 3 metres by pushing the wash head backwards and forwards over the area. 3.
Operation Washing Upholstery 1. Detach wash head from the solution tube and extension tubes. 2. Pull the extension tube out of the handle of the hose. 3. Attach the upholstery wash tool directly onto the handle of the hose and wrap the excess solution tube around as necessary. 4. To start water and solution flow, push the collar on the wash tool forwards. 5. When you see water swirling in the washing tool you are ready to start washing. 6. Pull the washing tool backwards.
505 900 Maintenance (Keep your Vax as good as new) Dust Bag and Filters: Removal and Replacement IMPORTANT: Always unplug the machine from the electrical output before removing the dust bag. IMPORTANT: Do NOT use the vacuum cleaner in dry mode without ALL of the filters in place. Turn off the vacuum cleaner and unplug it from the mains. Remove the hose. Unclip the retainer clips on either side of the vacuum cleaner and lift off to gain access to the dust bag compartment. vax.com.
Maintenance (Keep your Vax as good as new) IMPORTANT: Ensure that the machine is switched off and unplugged from the socket before carrying out any maintenance. Cleaning the Pre-Motor Filter Remove the motor top from the unit, turn on its side and remove the float housing in an anti-clockwise direction to unscrew. Remove the blue filter and wash under a tap. Allow to dry thoroughly before replacing back into the machine. Replace with a new filter as necessary.
505 900 Maintenance (Keep your Vax as good as new) Cleaning the Post-Motor Filter Remove the filter housing at the back of the machine. Remove the filter and wash under a tap. Allow to dry thoroughly before replacing back into the machine. Once dry, put the filter back into the housing and place back into the machine. IMPORTANT: Even with regular cleaning, filters have a limited lifespan and will eventually need to be replaced during the lifetime of the vacuum cleaner.
FAQ’s WARNING: To reduce the risk of personal injury, unplug the cleaner before performing maintenance/troubleshooting checks. Problem Cause Solution Cleaner won’t run Not properly plugged into electrical outlet. Plug in firmly. No electricity in electrical outlet. Check fuse or breaker. On/off switch not turned on. Push on/off switch to ‘on’. Blown fuse/tripped breaker. Reset circuit breaker or replace fuse.
505 900 Other Information Vax Service & Help Vax Careline: Australia New Zealand 1300 361 505 0800 800 900 Monday-Friday 8.30am to 5.00pm If you have queries or concerns about using your Vax, call the Vax Careline. Calls are charged at the standard local rate. Please make a note of the serial number and model number of the vacuum cleaner before calling. For the nearest Service Agent, please call the Vax Customer Careline or visit vax.com.
Notes 17 Vax Service line: AU: 1300 361 505 NZ: 0800 800 900 vax
505 900 Notes vax.com.
Distributed by Techtronic Industries Pty. Ltd. Level 1, 660 Doncaster Road, Doncaster, Australia 3108. www.vax.com.
