Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 1 Vax Careline: 0870 6061248 www.vax.co.uk BAGLESS UPRIGHT VACUUM CLEANER WITH TURBOTOOL Vax Model Number: V-041 BAGLESS UPRIGHT VACUUM CLEANER Vax Model Number: V-042 Instruction Manual Please read carefully before using this cleaner. Always fully extend the mains cable before use.
Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 2 Parts Overview 1. Diagram FRONT 1 BACK 21 2 13 14 3 12 4 15 5 6 7 11 8 16 20 19 9 18 10 17 Fig.
Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 3 Safety Information/Use & Function 2. Safety Information 19. Turn off the switch before unplugging. FOR HOUSEHOLD USE ONLY. When using the vacuum cleaner, basic safety precautions should always be observed, including the following: 20. Use only CE-approved 13 amp extension cords. Non-approved extension cords may overheat. Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over. 1. 2. 3. 4. 5. 6. 7. 8. 9.
Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 4 Use & Function 2. To secure, insert two (2) screws into the front of the back panel (Fig.3/2). 5. Fig.3/5 Fig.3/2 3. Place the upper handle on to the top of the cleaner (Fig.3/3). 6. V-041 only: Push the handle plug on to the front of the vacuum cleaner (Fig.3/4A). V-042 only: Push the blanking plug on to the front of the vacuum cleaner (Fig.3/4B). V-041 only: Clip the TurboTool™ on to the front of the TurboTool™ caddy (Fig.3/6). Fig.3/6 Fig.3/3 4.
Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 5 Use & Function/How to Operate 8. Slide the dusting brush on to the post on the lower caddy, with its bristles facing out (Fig.3/8A). Slide the extension tube/crevice tool in to the round slot on the front right side of tool caddy (Fig.3/8B). B 4. How to Operate Cord Release Turn the quick cord release for easy cord removal. Insert the cord into the cord clip (Fig.1/1 item 14); this will keep the cord out of the way while vacuuming (Fig.4/1). A Fig.
Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 6 How to Operate/Accessories On/off Pedal Plug the cord into the electrical outlet. Turn the cleaner on by pressing the foot pedal located on the back left side of the vacuum cleaner (Fig.4/3). 3. Choose any of the on-board accessories or use the hose alone. Simply push the attachment firmly on to the end of the extension tube or hose handle. To remove the tool, twist and pull apart gently (Fig.5/3). Fig.4/3 Fig.
Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 7 Accessories/Dirt Container & Filter: Removal & Replacement/Rotating Brushbar: Removal & Replacement Dusting Brush The dusting brush is used for furniture, venetian blinds, books, lamp shades and shelves. 5. Each time the dirt container is emptied, the filter should be cleaned. Tap the filter firmly against the inside of a rubbish bin until the dirt stops falling from the filter (Fig.6/5). 6.
Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 8 Rotating Brushbar: Removal & Replacement 2. Pull and lift off the nozzle guard (Fig.7/2). 3. With the new belt in place, pull and slide the brushbar into the nozzle, making sure that the end caps are in the correct orientation (Fig.7/6A). Rotate the brushbar manually to make sure belt is properly aligned (Fig.7/6). Fig.7/2 3. Lift and remove the brushbar. Dispose of the old belt (Fig.7/3). A Fig.7/6 4. Re-attach the nozzle guard (Fig.7/7). Fig.
Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 9 Clearing Blockages 8. Clearing Blockages Clearing Blockages from the TurboTool™ (V-041 only) WARNING: To reduce the risk of injury from moving parts, unplug before servicing. 1. Unwrap the hose from the caddy. Remove any obstruction (Fig.8/1). 1. Rotate the locking ring 180º and turn the TurboTool™ over (Fig.8/4). Fig.8/4 2. Lift the cover off the TurboTool™ and remove blockage (Fig.8/5). Fig.8/1 2.
Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 10 Troubleshooting 9. Troubleshooting WARNING: TO REDUCE RISK OF PERSONAL INJURY, UNPLUG VACUUM CLEANER BEFORE SERVICING PROBLEM: Cleaner won’t run Cause: Not properly plugged into wall outlet. Solution: Plug in firmly. Cause: No electricity in wall outlet. Solution: Check fuse or breaker. Cause: On/off switch not turned on. Solution: Push on/off switch to on. Cause: Motor thermostat has tripped. Solution: Switch off and unplug cleaner.
Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 11 Troubleshooting/UK Service & Help/Technical Specification PROBLEM: Air flow restricted with attachment use Cause: Attachment use restricts air flow. Solution: Check attachment. Cause: New carpet debris clogging air path. Solution: Remove obstruction. 10. UK Service & Help Vax Care 0870 6061248 Monday-Friday 9.00am to 5.00pm. An answerphone is available out of these hours. Any queries or concerns about using the Vax, call the Vax Careline.
Vax V-041/2 9th.qxd 2/23/05 12:34 PM Page 12 EEC STATEMENT OF COMPLIANCE Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the products V-041 Everyday Turbo/V-042 Everyday are manufactured in compliance with the following: Safety: 73/23/EEC Low Voltage Directive, as modified by 93/68/EEC EMC: 89/336/EEC Electromagnetic Compatibility Directive, as modified by 93/68/EEC Waste electrical products should not be disposed of with household waste.