VAX 4000 Model 100A Installation Information Order Number: EK–502AA–IN. A01 August 1993 This manual describes how to install and test the VAX 4000 Model 100A.
August 1993 The information in this document is subject to change without notice and should not be construed as a commitment by Digital Equipment Corporation. Digital Equipment Corporation assumes no responsibility for any errors that may appear in this document. The software described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license.
Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v 1 Installation Procedure Step Step Step Step Step Step Step Step Step Step Step Step 1: Choosing a Suitable Location . . . . . . . . . . . . . . . . . 2: Unpacking the System and Identifying the Parts . . 3: Connecting the Console Terminal . . . . . . . . . . . . . . 4: Connecting the ThinWire Terminator . . . . . . . . . . . 5: Connecting the SCSI Terminator . . . . . . . . . . .
Preface This manual describes how to install and test the VAX 4000 Model 100A. It also refers to information on connecting the system to a network, connecting external options to the system, and booting the operating system. Audience This manual is intended for anyone who wants to install the VAX 4000 Model 100A. It is written for both experienced and inexperienced users. Structure of This Manual This manual contains one chapter.
Conventions The following conventions are used in this manual: vi Convention Description MONOSPACE Text displayed on the screen is shown in monospace type. italic type Italic type emphasizes important information and indicates the complete titles of manuals. Note A note contains information that is of special importance to the user.
1 Installation Procedure This chapter shows you, step by step, how to install the VAX 4000 Model 100A. Step 1: Choosing a Suitable Location Follow these guidelines when choosing where to place the system unit: • Place the system unit where the room temperature is between 10°C and 40°C (50°F and 104°F) and the humidity is between 20% and 80%. • Place the system unit at least 1 metre (3 feet) from heaters, photocopying machines, or other operating equipment.
Step 2: Unpacking the System and Identifying the Parts 1. Unpack the system. 2. Make sure that you have all the parts listed on the packing slip. The loose-piece accessory kit is shipped with all basic systems. If you do not have all the parts listed, contact your Digital Sales representative.
Step 3: Connecting the Console Terminal 1. Connect one end of the terminal cable to the modified modular jack (MMJ) port 3. This system will be shipped with a label covering ports 0 and 1. After port 3 is properly identified as the console port, the OPA0 arrow label may be removed. 2. Connect the other end of the terminal cable to a DEC423 (MMJ) communications port on the console terminal.
Step 4: Connecting the ThinWire Terminator 1. Assemble the T-connector and the two terminators to form a ThinWire terminator. 2. Connect the ThinWire terminator to the system unit.
Step 5: Connecting the SCSI Terminator 1. Connect the SCSI terminator to the SCSI port. 2. Close the bail lock loops.
Step 6: Connecting the DSSI Terminators Connect all three DSSI terminators. Note If you ordered the KFDDA–BA single-slot-card model, only one DSSI terminator will be included and connected, and the two right-hand DSSI cutouts will be covered with blanks.
Step 7: Connecting the Power Cord 1. Ensure that the on/off switch is in the off (O) position. 2. Connect the power cord to the system unit. 3. Connect the other end of the power cord to an isolated, grounded circuit.
Step 8: Turning on the Console Terminal and System Unit 1. Turn on the console terminal. Wait until it completes its power-up test. (See the terminal documentation for more information.) 2. Check the terminal settings. See the VAX 4000 Model 100A Operator Information manual for the list of correct settings. 3. Turn on the system unit by setting the on/off switch to the on ( | ) position.
Step 9: Checking the Power-Up Test Results The power-up test can take several minutes to complete, depending on the number of installed options and on which default settings you use. 1. If the power-up test results on the screen are similar to the results in Example 1–1, the system has passed the power-up test. Go to step 9. 2. If the power-up test results on the screen are not similar to the results in Example 1–1, the system has not passed the power-up test. See Example 1–2 for a typical failure.
If SIMM_OD is not present or not plugged in correctly, the system responds with a display similar to the following example: Example 1–2 Unsuccessful Power-Up Test Screen KA52-A VX.X, VMB 2.14 Performing normal system tests. 72..71..70..69..68..67..66..65..64..63..62.. ! ? Test_Subtest_DC_88 Loop_Subtest=05 Err_Type=FF DE_NO_Memory_present.
Step 10: Connecting the System to a Network If you want to connect the system to a network, see the VAX 4000 Model 100A Operator Information manual. Step 11: Connecting External Options to the System If you want to connect external options to the system, see the VAX 4000 Model 100A Operator Information manual. Step 12: Booting the Operating System The system is supplied with factory installed software (FIS) on the system disk.
Reader’s Comments VAX 4000 Model 100A Installation Information EK–502AA–IN. A01 Your comments and suggestions help us improve the quality of our publications.
d Do Not Tear – Fold Here and Tape NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST CLASS PERMIT NO. 33 MAYNARD MASS.
