W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:03 Page 1 User Guide Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308 Carpet Washer Get Cleaning... What’s your Vax model number? (Located on the top flap of the packaging) e.g. W 9 0 - R U - B What’s your serial number? (Located on the base of the machine) – – – – – Note these down in case you need them in future. Please keep instructions for further use. vax.co.
W90-RU & W89-RU Series User Guide v1.4.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:03 Page 3 General Safety Information FOR HOUSEHOLD USE ONLY. 16. Keep the unit on the floor. When using the carpet washer, basic safety precautions should always be observed, including the following: 17. Do not use an extension cord. 18. Do not attempt to remove blockages with sharp objects as they may cause damage. 19. Store indoors put away after use to prevent tripping accidents. 20.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:03 Page 4 --- Operation Assembling your carpet washer handle 1 ‘Click’ 2 2 1 Press Locate locking pin and Insert handle and re-fit press in points shown locking pin. to remove. Locking pin will ‘click’ when in place. Assembling your tool caddy and hose Ensure locking tabs are horizontal. Rotate tabs 90˚ clockwise to lock caddy onto unit. Fit hose connector end in first. Attach caddy to unit top first.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:03 Page 5 Operation Before you begin cleaning ! NOTE: Do not over saturate your carpet. • Vacuum your carpets thoroughly. • Test for colourfastness - Wet a white absorbent cloth with the solution. In a small, hidden area of your carpet, gently rub the surface with the dampened cloth. Wait ten minutes and check for colour removal or bleed with white paper towel or cloth. If your carpet has more than one colour, check all colours.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide --- 2/3/11 10:04 Page 6 Operation Operating your pre-treatment wand (some models only ) NOTE: Pre-treating your carpet before washing will help to remove stubborn stains. NOTE: Do not over saturate your carpet. ! 40° C max Pour required dose of pre-treatment solution (approx. 40ml per 1L of water). Mix solution with warm Remove clean water water. (max 40˚ C) tank. Fill clean water tank with solution mix.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:04 Page 7 Operation Operating your carpet washer NOTE: Your dirty water tank is fitted with a float. When the dirty water tank is full or the floor head is not in contact with the carpet the float will shut off the suction at the floor nozzle. You will be able to hear if this has happened as the motor noise on the unit will increase. Once the float is activated, empty the dirty water tank if full.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:04 Page 8 --- Operation Picking up spills Remove hose. Pull wash tool back over spill to pick up liquid. Using the wash tool NOTE: Do not over saturate your upholstery. NOTE: The clean water tank will need to be filled with solution and water before use. For best results apply solution on the forward stroke and release the trigger to recover on the backward stroke. Press trigger to release solution.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:04 Page 9 Operation Protecting your carpets NOTE: Using Vax Carpet Guard solution will protect your carpets from future stains. NOTE: Do not over saturate your carpets. • Hold the Vax Guard solution approximately 1 metre away from the desired area and spray evenly. • Leave to dry for 30 minutes. vax.co.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:04 Page 10 --- Maintenance (Keep your Vax as good as new) WARNING: To reduce the risk of electric shock, turn the machine off and unplug from electrical outlet before performing maintenance/troubleshooting checks. ! Emptying the dirty water tank NOTE: Rinse out tank with clean water and leave to air dry before storing your machine. 1 2 Cleaning the float chamber filter 2 ! 40° C max 1 Rinse under water to remove debris (max 40ºC).
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:04 Page 11 Maintenance (Keep your Vax as good as new) Replacing the belt WARNING: DO NOT OPEN THE MOTOR COVER. ! ! Use a crosshead screwdriver to remove two (2) screws. Remove damaged/broken belt off the spindles. Replace new belt on to spindles and secure the belt cover. Storage • Empty and rinse out clean and dirty water tanks and leave to air dry before replacing. • You can remove the handle and tool caddy for convenient storage.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:04 Page 12 --- FAQs ! WARNING: To reduce the risk of personal injury, unplug the carpet washer before performing maintenance/troubleshooting checks. Is there an accessory missing? Why won’t the solution/clean water dispense? • Check the ‘Parts Overview’ page in this guide to make sure the part is definitely included in your unit. • The solution/clean water tank may be empty.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:04 Page 13 Other Information UK Service & Help Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308 Monday-Friday 8.30am to 6.30pm Saturday-Sunday 9.00am to 5.00pm If you have queries or concerns about using your Vax, call the Vax Careline. Calls are charged at the UK local rate. Please make a note of the serial number and model number of the vacuum cleaner before calling.
W90-RU & W89-RU Series User Guide v1.4.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:04 Page 15 Notes vax.co.
W90-RU & W89-RU Series User Guide v1.4.qxd:User guide 2/3/11 10:04 Page 16 --- Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK email: info@vax.co.uk - website: vax.co.uk Version 1.
