Specification Sheet

ManualsBrandsVaxcel Lighting ManualsLightingChatham Single Light 17-1/2" High Outdoor Wall Sconce

Page 1/4

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

T0249 / T0326

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

1. Energy saving fixture.

2. Use the dim-to-bright illumination option where

you want some minimum illumination through out

the night, such as at your front entrance or garage

door. Use the dark-to-bright illumination option

where you do not need minimum brightness, such

as the backyard or back porch.

3. When in manual override mode, use wall switch

to keep the light ON till dawn.

1. Read all instructions carefully before installation and

operation.

2. If you are not familiar with state and local electrical codes,

it is recommended that you consult with a qualified

electrician.

3. Before installation, shut off power at the main fuse or

circuit breaker box. Be aware that simply turning off the

wall switch is not sufficient to prevent an electrical shock.

4. This fixture requires a 120 VAC, 60 Hz power source.

5. Do not attempt to take the lantern apart; there are no

serviceable parts inside.

6. To avoid sensor damage by lightning or electrical surge,

make sure the grounding wire is securely connected.

7. For general safety and to avoid any possible damage to

the sensor, be sure the power is switched "off" before

replacing the bulb.

8. Compatible with most LED dimmable bulb.

Maximum Wattage: 60W Incandescent Bulb or 20W LED

dimmable Bulb.

Work Temperature: - 4°F~104°F

Hardware Package (included)：

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. Read and save these instructions.

170214

Important to Know

Features

Green Grounding

Screw (E)

Nipple (D)

Mounting Screw (B)

Wire Nut (C)

Hex Nut (F)

Washer (G)

Mounting Strap (A)

Rubber Pad (L)

End Cap (M)

Mounting Screw

Fixture Wire

Back Plate

Nipple

Mounting Strap

Hex Nut

Wire Nut

Washer

Fixture Grounding Wire

Green Grounding Screw

Outlet Box

House Grounding Wire

Type A Max. 60W Bulb OR

Max. 20W Dimmable LED Bulb

(not include)

Summary of content (4 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS T0249 / T0326 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. Features Important to Know 1. Read all instructions carefully before installation and operation. 2.
PAGE 2
Installation steps Turn off the power at fuse or circuit box. 1. Attach the nipple to the mounting strap, then secure it with a washer and hex nut. 2. Attach the mounting strap to the outlet box by using two mounting screws. 3. Pull out the source wires from the outlet box. Make wire connections using wire nuts as follows: ---Connect the hot wire (usually black insulation) from the power source to the black wire from the fixture.
PAGE 3
FIG.1 FIG.2 Manual Override Operation Diagram AUTO Mode Turn wall switch OFF-ON in 3 Seconds Turn wall switch OFF-ON in 3 Seconds again On the back of the sensor Time Manual Override Mode Low Level Sens Test 3H 6H Time 0 Low Level Sens Test 3H 6H 0 CUSTOMIZATION OPTIONS: Shut-off Delay The Shut-off delay is the length of time the light will stay at high-level brightness after motion has ceased to be detected.
PAGE 4
---In 3H or 6H Mode, the light is still on full brightness, even though it has been 3 hours or 6 hours at dusk, respectively: 1. Make sure no motion could be picked up by the sensor. 2. Make sure that mode entry is not in manual override. ---After performing 3H or 6H Mode, the light stays on full brightness after 3 minutes: 1. Make sure there is no movement that could be picked up by the sensor. 2. Adjust the time knob counterclockwise to reduce the delay shut-off time.