Installation Guide

ManualsBrandsVaxcel ManualsOutdoor Wall SconcesVaxcel Lighting Hedron 1 Light 8" Wide Outdoor Wall Sconce with Motion Sensor Included

Page 1 / 4

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

T0127

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. Read and save these instructions.

Bulb Type A Max.100W

(not included)

Features

141208

Important to Know

1. Read all instructions carefully before installation and

operation.

2. If you are not familiar with state and local electrical codes,

it is recommended that you consult with a qualified

electrician.

3. Before installation, shut off power at the main fuse or

circuit breaker box. Be aware that simply turning off the

wall switch is not sufficient to prevent an electrical shock.

4. This fixture requires a 120V AC, 60 Hz power source.

5. Do not attempt to take the lantern apart; there are no

serviceable parts inside.

6. To avoid sensor damage by lightning or electrical surge,

make sure the grounding wire is securely connected.

7. For general safety and to avoid any possible damage to

the sensor, be sure the power is switched "off" before

replacing the bulb.

Maximum Wattage: 100W Incandescent bulb

Work Temperature: -4ºF ~ 104ºF

House Grounding Wire

Green Grounding Screw (C)

Wire Nut (E)

Mounting Screw (B)

Headless Screw (D)

Outlet Box

Fixture Wire

Lock Nut (F)

Back Plate

Rubber pad(G)

Fixture

Ball Nut(H)

Socket

Metal Frame

Mounting Plate (A)

Fixture Grounding Wire

Mounting

Screw (B)

Green Grounding

Screw (C)

Lock Nut (F)

Wire Nut (E)

Rubber Pad (G)

Mounting Plate (A)

Headless

Screw (D)

Ball Nut (H)

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.

1. Energy saving fixture.

2. Use the dim-to-bright illumination option where

you want some minimum illumination through out

the night, such as at your front entrance or

garage door. Use the dark-to-bright illumination

option where you do not need minimum

brightness, such as the backyard or back porch.

3. When in manual override mode, use wall switch

to keep the light ON till dawn.

Hardware Package (included)：

Summary of content (4 pages)

PAGE 1
T0127 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE. Important to Know Features NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. 1. Energy saving fixture. 2. Use the dim-to-bright illumination option where you want some minimum illumination through out the night, such as at your front entrance or garage door.
PAGE 2
Installation Steps Turn off the power at fuse or circuit box. 1. Thread two headless screws through the mounting plate, then secure them with four lock nuts (two on each side of the mounting plate). Adjust the length of the headless screws if necessary. Note: Make sure that the headless screws are lined up horizontally, to ensure that the fixture will be level. 2. Attach the mounting plate to the outlet box by using two mounting screws. 3. Pull out the wires and grounding wire from the outlet box.
PAGE 3
5. Manual Override MODE (nighttime operation only; on at dusk, off at dawn) ● In 3, 6 or 0 mode, to shift to manual override mode, turn off the wall switch in 3 seconds and then turn it on again, the light will turn to high-level brightness at dusk, and turn off automatically at dawn. To return to the previous settings, turn off the wall switch in 3 seconds and then turn it on again. (See FIG.2) ● The lights will turn off automatically at dawn.
PAGE 4
Troubleshooting ---If the light does not work at all: 1. Make sure the wall switch and circuit breaker are on. 2. Make sure the wiring connection is correct. 3. Make sure the bulb is not burned out. 4. Cover the sensor with your palm to verify that the ambient light level is not too high. ----In Test Mode, if the light stays on full brightness after 5 seconds: 1. Check whether the motion is detected at all time. ----After performing 3H or 6H mode, or in 0 H mode.