ELECTRIC FLAT PANEL FIREPLACE HEATER OWNERS MANUAL Model Numbers: KVWALL-24B; WS-G-03-2 MINI Only use this heater as described in this manual. Any other use is not recommended by the manufacturer, and may cause fire, electric shock, or other personal injury. WARNING! Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, serious personal injury, or death.
IMPORTANT SAFETY INFORMATION! WARNING ALWAYS keep electric cords, home furnishings, drapes, clothing, papers, or other combustibles at least 3 feet (0.9m) away from the front of this heater, and away from the bottom, sides, and rear of this heater. DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater. DO NOT COVER this heater or block the air vents at all. Doing so could cause a fire.
WARNING Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside! ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, before replacing the light bulb, or before relocating the electric fireplace. NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp or come in contact with water. NEVER hang this unit on a wall directly below an electrical outlet.
Preparation This product includes a GLASS panel! Always use extreme caution when handling glass. Failure to do so could result in personal injury or property damage. Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts and assembly steps are grouped for free-standing or wall-hanging use. Check the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible.
NOTICE The wall mount fasteners included with this fireplace are for use ONLY with a wood-framed wall covered in drywall (sheet rock). For concrete walls, cinder blocks, or other wall types, consult a professional for the best attachment methods. ALWAYS unplug this fireplace heater before assembly or cleaning, or before relocating. Failure to do so could result in electric shock, fire, or personal injury. Drywall Studs STEP 2. A. Locate the wall studs using an electronic stud-finder. B.
E E B B B B B B STEP 4. Align the holes in the wall bracket (E) with the pilot holes and drywall anchors. Thread three wood screws (B) through the holes in the wall bracket and directly into the wall studs and drywall anchor(s). Make sure the bracket is level. Tighten all screws securely with a screwdriver. ALWAYS unplug this fireplace heater before assembly or cleaning, or before relocating. Failure to do so could result in electric shock, fire, or personal injury. D E A A STEP 5. A.
Operation Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in electric shock, fire, serious injury, or death. Power Make sure the ON/OFF switch, located on the left side panel, is in the OFF position. Plug the power cord into a 110~120 Volt 15 Amp grounded outlet (see IMPORTANT SAFETY INFORMATION on Pages 2 and 3). Make sure the outlet is in good condition and that the plug is not loose.
Control Panel Operation BUTTON ON OFF POWER ACTION and INDICATION CONTROL PANEL 1. Press ON (l). Power turns on. All functions are enabled. 2. Press OFF (O). Power, flame effect, and all functions turn off. 1. Press once. Flame effect and indicator turn on. 2. Press again. Power and all functions turn off. 1. Press +. ½ h light turns on. Timer is set to ½ hour. + TIMER - 2. Press again. 1h light turns on. Timer is set to 1 hour. 3. Press until desired setting is reached.
Remote Control (Control panel POWER switch must be ON to use remote control.) BUTTON ACTION and INDICATION REMOTE CONTROL 1. Press once. Flame effect turns on High and indicator light turns on. POWER 2. Press again. Power and all functions turn off. 1. Press once. Small indicator lights up. Fan blows cool air. 750W heater turns on and blows warm air. lights up. 1500W 2. Press again. Large indicator heater turns on and blows hot air. HEATER 3. Press again. Heaters turn off.
Remote Control Information NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Plastic: • Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water. • NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface. Replacing the light bulb ALWAYS turn the heater OFF and unplug the power cord from the outlet before changing the bulb. Failure to do so could result in electric shock, or personal injury. 1. Allow the fireplace to cool down before moving it. 2. Lay the fireplace down on a soft surface. 3.
Limited Warranty Manufacturer warrants this product for replacement or repair of parts to the original purchaser for a period of 1 (one) year from the original date of purchase. The original dated sales receipt is required for all warranty claims. This limited warranty does not cover replacement of glass or light bulbs, shipping costs, and normal wear and tear.
