CYCLECOMPUTING INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D´INSTALLATION ET D´UTILISATION MANUALE D´INSTALLAZIONE E FUNZIONAMENTO INSTALACION Y OPERACIÓN MANUAL HANDLEIDING HC12.
P1 screw
P2 P3 1-5 mm
P4 LOCK UNLOCK
P5 OPEN CLOSE
P6
P7 IMPORTANT Rubber washer CLOSE OPEN
P8 Press AC-Button to Begin or install battery (P6) automatic ••••••• Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select
P9 1x WS in mm / inch
P10 ETRTO 47-305 47-406 34-540 47-507 23-571 40-559 44-559 47-559 50-559 54-559 57-559 37-590 20-571 16x1,75 20x1,75 24x1 3/8 24x1,75 26x1 26x1,5 26x1,6 26x1,75 26x1,9 26x2,00 26x2,125 26x1 3/8 26x3/4 WS in mm KMH WS in inch MPH 1272 1590 1948 1907 1973 2026 2051 2070 2089 2114 2133 2105 1954 50,1 62,6 76,7 75,1 77,7 79,8 80,7 81,5 82,2 83,2 84,0 82,9 76,9 ETRTO 32-630 40-622 47-622 40-635 37-622 18-622 20-622 23-622 25-622 28-622 32-622 37-622 40-622 27x1 1/4 28x1,5 28x1,75 28x1 1/2 28x1 3/8 700x18C
P11 SET Metric System SET WS 1 Start at TRIP DIST Press MODE 1 for 3 sec. Press MODE 2 to select between KMH and MPH Press MODE 1 to set WS1 Press MODE 2 to increase •••••••••••• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •• • • • • • SET WS 2 ••••• Press MODE 1 3 sec. to end ••••• Press MODE 1 to switch Press MODE 2 to increase Press MODE 1 to set WS2 Press MODE 1 3 sec.
P12 Press MODE 1 3sec.to start Press MODE 2 to switch between 24h or 12h Press MODE 1 to set the hours MODE 2 to increase the hours Press MODE 1 3 sec.
P13 P14 Set ••••••• Press MODE 2 to increase Press MODE 1 to switch Press MODE1 3 sec. to end after you set the navigator Reset ••••••• Important Navigator in Display Press MODE 2 to reset •••••••••••••••••••••••••• Press MODE 1 3sec.
P15 Set ODOMETER Press MODE 1 3sec.to start Press MODE 2 to increase Press MODE 1 to switch Press MODE1 3 sec.
P16 BIKE CHECK Press any button BIKE CHECK disappears The service icon will remain flashing. Another 50 km/35 mi.
P17
P18 Set limits High-limit Press MODE1 3sec.
P19 Press PULS Press MODE1+ MODE2 to stop Press MODE1+ MODE2 to start again
OWNER'S MANUAL - VDO HC 12.6 GB Index Preface 1. Mounting 1.1 Handlebar holder 1.2 Speed transmitter (sensor) 1.3 Spoke magnet 1.4 Twist-Click mounting of computer onto handlebarholder 2. Basic information on how to operate your VDO HC 12.6 2.1 Interrogating information 2.2 Calling set-up mode 2.3 Button / key covering in set-up mode 2.4 Resetting of information modes to zero 2.4.1 Cycling Information 2.4.2 Heartrate Information 2.4.3 NAVI GATOR 3. Installing the batteries 3.
GB HC 12.6 Preface Thank you very much for buying a VDO HC 12.6 bicycle computer featuring heart rate / pulse functions. The more familiar you get with this model, the more enjoyable your trips are going to be. Hence, our urgent request: Please read thoroughly all the information provided in this manual. You are getting important and useful hints for operation to make you fully benefit from all the technical features of your VDO HC 12.6.
1.4 Twist-Click mounting of computer on to holder The Twist-Click mounting has been exclusively developed for the new line of VDO computers. The VDO HC 12.6 also features the Twist-Click-System. The computerhead is put onto the handlebar and by a right turn of the computerhead (TWIST) fixed to the holder (CLICK). It is just as easy to remove the computerhead from the handlebar holder. Twist it to the left, remove computerhead from handlebar holder. GB HC 12.6 2.
GB HC 12.6 2.1 Interrogating information With the MODE1 key you call up following information: TRIP DIST/ RIDE TIME/ AVG SPEED/ MAX SPEED TRIP DIST trip counter for your individual trip, counting to 999.99 KM or M RIDE TIME trip timer featuring automatic start/stop function up to 19:59:59 h AVG SPEED average speed, accurate to two decimal points MAX SPEED maximum speed achieved during a ride up to199.5 KM or M Important: If the ride timer overflows 19:59:59 h, it is automatically reset to 00:00:00.
2.2 Calling up set-up modes The MODE 1 key calls up any set-up mode Calling up the set-up modes requires a 3 sec pressing of the MODE 1 key. GB HC 12.
GB HC 12.6 2.4 Resetting of information modes to zero By pressing MODE 2 for 5 sec. any of the following information is simultaneously reset to zero 2.4.1. Cycling Information Get any of these informations in display TRIP DIST--RIDE TIME--AVG SPEED--MAX SPEED Press MODE 2 for 5 sec. to reset all of above information symultaneously. 2.4.2 Heartrate Information Get any of these informations in display STOP WATCH--AVG PULSE--MAX PULSE--TIME ABOVE--TIME IN--TIME BELOW Press MODE 2 for 5 sec.
3. Installing batteries GB 3.1 Installing the battery into the computer head To save battery power, your VDO HC 12.6 comes with the battery not yet fitted. Prior to initial use the batteries will first have to be installed with the positve pole on top. HC 12.6 Warning: Once the battery is installed your VDO HC 12.6 start the set-up of display language. See also chapter 4.
GB HC 12.6 4.2 Selecting the wheelsize Your computer VDO HC 12.6 indicates your wheel size as WS (Wheelsize) = wheel circumference. Your VDO HC 12.6 is able to process two different wheelsizes for two different bikes (i.e. road bike and mountainbike) The following default values are preset Wheelsize 1 WS1 = 2155 mm wheel circumference Wheelsize 2 WS2 = 2000 mm wheel circumference Warning: After a battery change the above defaults are automatically applied.
4.2.3 Entering the precise wheelsize GB Step 1: By pressing MODE 1 call TRIP DIST in your display. Step 2: Press MODE 1 for 3 sec. In the upper part of the display you see "WS1" and "KMH" or "MPH" flashing. The lower part of the display alternately shows HC 12.6 "ENTER MTRIC SYSTM" and "KMH"/"MPH" Step 3: With MODE 2 you choose whether you want kilometers=KMH oder miles=MPH as a measuring unit. Step 4: Once the conversion of KMH or MPH has been chosen, you proceed by briefly pressing (0.1 sec) MODE 1.
GB HC 12.6 4.4 The NAVIGATOR The NAVIGATOR is a second, individual trip distance counter that can be: • manually reset to zero • preset to a certain value, the trip distance is then counted from this value. The NAVIGATOR is very helpful following road book instructions or tour suggestions of bike magazines. For example, your road book tour wants you "to go straight for a mile and then make a right turn, then go on for half a mile and make a sharp left turn".
4.5 Presetting the odometer After a battery change, you can re-enter previous odometer values (for both bikes) into your VDO HC 12.6. GB HC 12.6 Step 1: With MODE 2 call "ODO1 METER" or "ODO2 METER" into display, depending which one of these values you want to re-enter. Step 2: Press MODE 1 for 3 sec. The lower part of the display alternately shows "ENTER ODO1 METER" or "ENTER ODO2 METER" plus the respective value with the last number flashing.
GB HC 12.6 7. Pulse information of your VDO HC 12.6 Your VDO HC 12.
9. Setting of pulse limits With your VDO HC 12.6 you determine upper and lower limits for your pulse / heart rate to define your training zone. GB HC 12.6 During initial setup or when the AC-button at the rear of the housing has been pressed, following values apply by default: • Lower limit LO 80 • Upper limit HI 140 Step 1: Call any pulse information into display by pressing the PULSE button. Step 2: Press MODE 1 for 3 sec.
10. The stopwatch GB HC 12.6 10.1 Stopwatch (automatic) With your VDO HC 12.6 running (not in Sleep-Mode), the receiver for pulse signals is activated as well. As soon as the chest belt (sender) starts transmitting pulse signals, the STOPWATCH will start automatically. The STOPWATCH may also be manually started and stopped. (see manual operation of the stopwatch).
12. Display of training times within preset target range training zones. With your VDO HC 12.6 you determine your upper and lower pulse limits Limits setup see paragraph 9. GB HC 12.6 Training times within preset target range training zones are only registered if • the computer is switched on, • the chestbelt sender is transmitting pulse signals, • the STOPWATCH has not been put to a manual halt, Training times within preset target range training zones are called up by pressing the PULSE button.
14. Troubleshooting GB HC 12.6 This chart outlines possible malfunctions, their causes and removal. malfunctions irregular LCD readout (i.e.
15. Warranty We warrant VDO HC 12.6 (chestbelt, sensor, computer head and handlebar holder) to the original purchaser for five years from date of purchase against defects in material and workmanship. This does not cover the batteries, cables and defects resulting from normal wear and tear, improper care, accidents, abuse or alteration. GB HC 12.6 Please take care to retain your receipt of purchase. In case of legitimate complaints, you are entitled to receive a comparable replacement model.
GB HC 12.6 16. Technical data dimensions computer chestbelt handlebar holder batteries radio frequency chest belt (transmitter) range operating temperature range speed measuring range trip distance counter NAVIGATOR odometer 1 odometer 2 TOTODO odometers 1+2 wheelsize pulse measuring range width 42 x ht 52 x depth 14mm computer chestbelt chestbelt LCD-display 2,5 km/h minimum 100 mm minimum 40 minimum 17.