Specifications

ManualsBrandsVDO Dayton Manualscar media receiversCD 2200

* Depending on version

• Blue lead A5 (Electronic/Motor Aerial) :

This radio can provide a 12V signal for the

control of an automatic motor aerial or the

supply of an electronic aerial by connection.

Do not use this connection for the supply lead

of the aerial motor!

• Orange lead A6 (Pilot light) : Connect to

the dashboard illumination wiring of the car.

When the car headlights are switched on, the

backlight to the power key remains illuminated

(even when the radio is switched off). When

the set is on with this connection , the

brightness of the display is reduced.

CONNECTOR B (fig.2)

Loudspeakers (use 4 ohm loudspeakers

only)

• Do not connect any of the loudspeaker leads

to earth or directly to a booster/amplifier or via

an external fader!

• Connecting 4 loudspeakers

Front Rear

Left+ Green [B5] White [B7]

Left- Green/black [B6] White/black [B8]

Right+ Grey [B3] Blue [B1]

Right- Grey/black [B4] Blue/black [B2]

– To check the loudspeaker connections keep

the 'SCAN' key pressed and switch on the set.

To cancel switch off the set.

BLUE CONNECTOR C * for a Digital CD

changer (available separately) (fig. 3)

• You can only connect the following CD changer

with a digital output to this set :

- CH0400 or CH0600 or CH1000

Useful tips

Recommended connection instructions between

the CD changer and headunit :

1. Ensure that the Connector A (power supply) is

removed from the headunit.

2. Finish all connections between the CD changer

(see mounting instructions for the CD changer)

and the headunit.

3. Reconnect the Connector A (power supply) to

the headunit.

INSTALLATION

If your car is equipped with ISO connectors,

simply insert them in connectors of the car radio.

If not, you can use an adaptor cable (Refer to the

table on the separate installation card). Ensure all

cables are installed so that they cannot be

damaged by sharp edges or moving parts.

PREPARATION

Voltage and polarity: The set must be connected

to a 12V car battery with negative terminal to

earth (car chassis). Installation in vehicles not

fulfilling these requirements could result in

malfunction, damage or fire.

Warning: To prevent short-circuiting, disconnect

the negative car battery terminal until the set has

been mounted and connected (fig.1 See separate

installation card).

CONNECTOR A (fig.2)

POWER SUPPLY CONNECTIONS

• Red lead A7 : Connect to a permanent 12V

supply. This is the main power supply. Ensure

this connection can handle a current of 10A.

• Yellow/red lead A4 : Connect to a switched

12V supply (switched on/off by car ignition).

• Brown lead A8: Connect to earth (car

chassis).

This connection set up will enable you to make

full use of the ON/OFF LOGIC function of this set

limiting the use of the set to 1 hour after removal

of the ignition key. If this feature does not appear

to be functioning as expected you may require

an adapter cable (EA6259). See reverse of

installation card.

OPTIONAL CONNECTIONS (fig. 2)

• Pink lead A1 * (SDVC AND SPEED

WARNING) :

Speed Dependent Volume Control

automatically increases and decreases the

volume as a result of the car's speed.

Speed Warning can be used to inform you that

you are exceeding a certain speed.

• Connect pin A1 to a signal from the

speedometer of your car. Some cars are

already prepared for it (e.g. certain VW &

Vauxhall/Opel cars), please consult your dealer.

If not, you may need a more detailed

installation requiring extra equipment to

enable your car to become compatible.

This can only be accomplished by persons

familiar with automotive electrical and

mechanical systems. After connection see

‘SPECIAL FUNCTIONS’.

Complies with 21 CFR 1040.10

Summary of content (18 pages)

PAGE 1
INSTALLATION • Blue lead A5 (Electronic/Motor Aerial) If your car is equipped with ISO connectors, simply insert them in connectors of the car radio. If not, you can use an adaptor cable (Refer to the table on the separate installation card). Ensure all cables are installed so that they cannot be damaged by sharp edges or moving parts. : This radio can provide a 12V signal for the control of an automatic motor aerial or the supply of an electronic aerial by connection.
PAGE 2
OTHERS CONNECTIONS (fig.2) Line-output * • You can connect a power amplifier (with 2 additional loudspeaker) to this set with the RCA cable. – Connect Red socket to Right channel and white socket to Left channel. – Connect Blue wire to Amplifier Remote on/off. TELEPHONE IN • If your car telephone or the car kit of your mobile phone provides both the mute signal and loudspeaker connection, its output can be amplified through the car's front speaker. – Connect the telephone mute wire to Pink lead wire (TEL.
PAGE 3
MOUNTING METAL SLEEVE (fig.4) • Install the metal sleeve (dimension 182x53 mm) in the dashboard. For optimal performance of the CD player*, the metal sleeve should be positioned horizontally (between -10o and +30o). • Fix metal sleeve into place by pressing the metal tags outwards using a screwdriver. MOUNTING RADIO This radio can be properly installed either from conventional Front Mounting or Rear Mounting.
PAGE 4
SECURITY LIGHT • When the car ignition is switched off and the detachable front is removed, the red light flashes. SECURITY For theft protection this set is provided with the following security features : DETACHABLE FRONT Take the detachable front with you when leaving the car. Keep it in its protective cover. Always replace the detachable front before starting to drive. Useful tips You can switch off the flashing warning light. • See INITIAL SETTINGS; select Option 'LED' and set the Choice to 'OFF'.
PAGE 5
INITIAL SETTINGS It is possible to modify many of the set's initial settings according to your preferences. • Enter the Initial Settings menu. • Select one of the option you want to modify • Alter the Choice. • Leave the Initial Settings menu : The set automatically leaves the Initialisation mode about 1 minute after your last operation. Option ( or ) Choice ( or Usage TEMP * [NO, C, F] Select the desired temperature format (when a temperature sensor is connected).
PAGE 6
INITIAL SETTINGS SCAN [5, 10, 15] Select the scan time (station or track). TIME * [24H, 12H] Select desired clock format. (See 'SETTING THE CLOCK'). CLK * [MAN, AUTO] Select 'AUTO' to activate RDS clock or 'MAN' to set clock manually. (See 'SETTING THE CLOCK'). TA [0, +1, +2, +3, +4] Volume level of Traffic Announcement, News bulletins and Alarm messages relative to tuner. SRCH [DX, LO] Select 'LO' if you wish to search only for strong stations during automatic tuning to a frequency.
PAGE 7
SPECIAL FUNCTIONS SDVC (SPEED DEPENDENT VOLUME CONTROL) AND SPEED WARNING • See INSTALLATION for connection instructions. CLOCK * This set has a clock that can either be manually set by you or can be automatically updated via the RDS signal. SDVC * To compensate for surrounding noise this function automatically increases the volume of the set as a result of the car's speed. Four compensation levels can be selected. Level 1 gives a small increase up to level 4 which gives a greater increase.
PAGE 8
SPECIAL FUNCTIONS STORE A SPEED Ensure in 'INITIAL SETTINGS' option 'SPD' is set either to 'KM/H' or 'MPH'. TEMPERATURE WARNING * You can connect a temperature sensor to this set to give you a visible and audible warning automatically when the outside temperature becomes lower than 3oC. See 'INSTALLATION' then 'INITIAL SETTINGS' option 'TEMP'. • Activate / Deactivate temperature warning. 1. Drive at the desired speed. 2. To record the speed e.g.
PAGE 9
MUTE (Silence) : • Mute the set or cancel the mute : AUDIO ADJUSTMENT ON/OFF • Switch the set on or off : You can use the set even when the car ignition is switched off. See 'INSTALLATION'. The silent period may be interrupted by traffic announcements (if TA/NEWS is switched on). VOLUME Please make sure you can still hear the traffic (horns, sirens........
PAGE 10
RADIO Useful tips WAVEBAND • Select the desired waveband : Detachable front of set feels warm? • Some heat is always generated by the set. Volume fluctuates. • Check SDVC connections and calibration. If problems persist consult your dealer. The display shows : FM1 or FM2, MW1, or MW2, or LW (when Choice is 'EUROPE' under 'RADIO' option; see INITIAL SETTINGS). Speed warnings do not correspond with actual speed. • Redo speed calibration.
PAGE 11
MANUAL TUNING (if you know the frequency of the required station) • To switch to manual tuning : AUTOMATICALLY STORING STATIONS (AUTO-STORE) By simply pressing one key you can automatically store 10 strongest FM stations (on the FM2 band) or 10 strongest MW stations (on the MW2 band). When you use Auto Store, the new stations replace any stations previously stored in the FM2 band or the AM2 (MW2) band.
PAGE 12
ALARM MESSAGES (PTY Alarm) This set automatically receives emergency messages made by the broadcaster. – During the messages the display shows 'ALARM' and the station-name alternately. RADIO DATA SYSTEM (RDS) ON FM Many FM stations broadcast RDS information. This set uses the RDS information to offer you many advantages including : DISPLAY OF STATION-NAME The set displays the name of the station instead of its frequency.
PAGE 13
Useful tips Useful tips Display shows 'NO TA', and set beeps at intervals. • The tuned station becomes too weak to enable the reception of Traffic Announcements. Use search tuning to find another station. • If the TA mode is switched on, search tuning only selects stations which enable the reception of Traffic Announcements. You can switch off RDS features if not in use. • See INITIAL SETTINGS; select Option 'RDS' and set Choice to 'OFF'. - All above RDS related features e.g. A-Z, MEMO, key, etc...
PAGE 14
• Activate/Deactivate FAST FORWARD : CASSETTE PLAYER (CR2100/ CR2200) PLAYBACK 1 Open the front. 2 Slide the cassette, with the open side to the right into the cassette opening. 3 Close the front. The display briefly shows 'TAPE CR' if a metal or chromium cassette is inserted. Playback starts. – You hear the radio during this operation. If you continue fast winding until the end of the tape, playback restarts automatically.
PAGE 15
PREVIOUS / NEXT TRACK Select the desired track. • Previous tracks : CD PLAYER AND CD CHANGER* CD PLAYBACK (CD Player) (CD2100/ CD2200) This CD player is suitable for 12cm disc. 1 Open the front. 2 Slide the disc into the slot with the label facing upwards. 3 Close the front. Playback starts. • Next tracks : – Playback resumes with the chosen track. FAST BACKWARD / FORWARD To quickly move through the disc • Backwards : • If a disc is already inserted : Select CD as SOURCE : • Forward : Playback starts.
PAGE 16
Useful tips Display shows 'CD ERROR' and set beeps. • Check that the discs have been inserted the correct way and that you have not inserted a damaged or dirty disc. Distorted sound during playback. • Player unable to read disc. CD damaged or dirty. Display shows 'NO CD'. • Check that the CD mechanism or CD magazine has been loaded with disc(s). Display shows 'NO MAG'. • No CD magazine in the CD changer. Useful tips Display shows 'NO FRONT'. • Check that the front of CD changer has been closed.
PAGE 17
REMOTE CONTROL A wired remote control can be connected to this set. See your dealer for more information. The remote control allows you to carry out some of the main functions of the set, without the need to take your eyes off the road while driving. This increases your safety. CASSETTE (CR2100 / CR2200) • Previous / next track : Select desired track. • Rewind/ fast forward : Activate/deactivate tape fast forward or rewind. AUDIO • Volume : Adjust the volume by turning the wheel.
PAGE 18
DISPLAY OPTIONS Choose what the display shows : In Radio mode : Station name. (If available and RDS is active). Programme type (if available) Frequency Clock * Temperature (if sensor connected and activated) In Cassette mode (CR2100 / CR2200) : Depending on current operation. Clock * Temperature (if sensor connected and activated) Total track and playing time. Clock * In CD mode (CD2100 / CD2200) : Current track and track time.