English page 1-16 GB C 08 Deutsch Seite 17-32 D C 08 Français page 33-48 F C 08 Italiano pagine 49-64 I C 08 Español pagina 65-80 E C 08 Nederlands pagina 81-96 NL C 08
ETRTO 47-305 47-406 34-540 47-507 23-571 40-559 44-559 47-559 50-559 54-559 57-559 37-590 20-571 16x1,75 20x1,75 24x1 3/8 24x1,75 26x1 26x1,5 26x1,6 26x1,75 26x1,9 26x2,00 26x2,125 26x1 3/8 26x3/4 WS in mm KMH WS in inch MPH 1272 1590 1948 1907 1973 2026 2051 2070 2089 2114 2133 2105 1954 50,1 62,6 76,7 75,1 77,7 79,8 80,7 81,5 82,2 83,2 84,0 82,9 76,9 ETRTO 32-630 40-622 47-622 40-635 37-622 18-622 20-622 23-622 25-622 28-622 32-622 37-622 40-622 27x1 1/4 28x1,5 28x1,75 28x1 1/2 28x1 3/8 700x18C 700
INSTALLATION AND OPERATION MANUAL - VDO CYTEC C 08 GB Preface Thank you for buying a VDO CYTEC bicycle computer. The more familiar you get with this model, the more enjoyable your trips are going to be. Please read thoroughly all the information provided in this manual. You are getting important and useful hints for operation to make you fully benefit from all the technical features of your VDO CYTEC bicycle computer.
2. Mounting the speed transmitter GB The sensor should be mounted on the same side of the fork as the holder is on the handlebar. C 08 Watch out: Do not tighten the cable ties yet! Accurately position the spoke magnet and the sensor first, then tighten the cable ties. 3. Mounting the spoke magnet Distance between magnet and sensor should be approx. 1-5 mm.
In case this distance is not achievable in the current positioning, slide the sensor and the magnet on the fork or spoke accordingly. GB C 08 1-5mm 1-5mm LOCK 4. Twist-Click mounting of computer onto holder UNLOCK The Twist-Click mounting has been exclusively developed for the new line of VDO CYTEC computers. The computerhead is put onto the handlebar and by a right turn of the computerhead (TWIST) fixed to the holder (CLICK). It is just as easy to remove the computerhead from the handlebar holder.
5. Installing battery into computer head GB C 08 To save battery power, your VDO CYTEC comes with the battery not yet fitted. Prior to initial use you have to install the battery first. OPEN CLOSE If you find the computer is not functioning properly after a battery change, push the AC-button (Auto Clear) on the rear side of the computer to reset.
6. Information features of your VDO CYTEC C 08 GB Your VDO CYTEC C 08 provides you with following information: C 08 KMH-MPH TRP RID AVS MAX CLK ODO current speed indicated in either KMH or MPH, featuring automatic conversion into MPH trip counter, counts your trip distance up to 999,99 km or miles. trip timer, keeps track of the actual riding time featuring automatic start/stop function, up to 9:59:59 (hrs:min:sec) average speed, accurate to two decimal points.
GB C 08 7.
These buttons / keys have several functions. All functions of the respective buttons / keys outlined in the following chart below. Your display Button / Key indicates following to be pushed information TRP-AVS-RID-MAX MODE 1 CLK- ODO MODE 1 TRP-RID-AVS MODE 1 TRP CLK ODO CLK- ODO TRP-RID-AVS-MAX MODE 1 MODE 1 MODE 1 MODE 2 MODE 2 TRP-RID-AVS-MAX MODE 2 Length of pushing the button / key brief (0.1 sec) brief (0.1 sec) GB C 08 What is going on? next information from MODE 1 is indicated.
GB 8. Scroll function C To provide any information at a glance, your VDO CYTEC 08 C 08 features a scroll function. Calling up the scroll function automatically displays information for a period of 1.5 sec. Scroll function may be called upon if any of the following information is on display: TRP-AVS-RID. Scroll function is activated by pressing the MODE 1 button for 1.5 sec. 9. Comparison of current and average speed SCROLL Press MODE 1 1,5 sec.
10. Set-up mode GB Your VDO CYTEC C 08 features the following set-up procedures wheelsize = WS clock = CLK odometers = ODO set-up starts out of TRP in display set-up starts out of CLK in display set-up starts out of ODO in display No matter which set-up mode is used for your VDO CYTEC , the procedure is the same. You can start the set-up mode for a certain display by pressing the MODE 1 button for 5 sec. With this MODE button you may also exit the set-up mode at any time.
GB C 08 1x WS in mm / inch Programming (setting up) your wheelsize Step 1: Call TRP information in your display. Step 2: Press MODE 1 button for 5 sec. "WS" is displayed along with an alternating flashing symbol for KMH and MPH. Step 3: By pressing the MODE 2 button you can choose whether you want MPH or KMH readout on your display. Step 4: Once you have chosen your measuring unit, continue by pressing the MODE 1 button briefly (0.1 sec).
GB MODE 1 5sec. MODE 1 5sec. to quit C 08 MODE 2 0,1sec. to change from KMH to MPH MODE 1 0,1sec. switch to next MODE 1 to start to switch to quit MODE 2 to increase to change from KMH to MPH MODE 1 0,1sec. switch to next MODE 1 0,1sec. switch to next MODE 2 0,1sec. to increase MODE 1 0,1sec. switch to next MODE 1 0,1sec.
12. Setting the clock CLK GB C 08 Your VDO CYTEC C 08 features a clock with hour and minute display. 12 h or 24 h display selectable. To access the clock set-up mode proceed as follows: MODE 1 5sec. to start Step 1: call in the CLK information into your display Step 2: Press the MODE 1 button for 5 sec. The set-up mode for the clock starts. You will either see the figure "24" or "12" flashing reflecting the hour-mode programmed. To set up your clock use MODE 1 and MODE 2 buttons. (see set-up mode).
13. Programming (setting-up) your odometer ODO GB You can enter individual odometer values into your VDO CYTEC C 10 at any time, i.e. transferring data from your old computer into your new VDO CYTEC C 10 or after a battery change. Watch out: after a battery change, your data for total ODO is reset to zero. TIP: If you want to re-enter your totals after a battery change, take down the value for ODO before removing the battery. Step 1: Call information for ODO into your display.
GB C 08 14. Resetting information to zero The following information may be reset to zero with your VDO CYTEC C 08. TRP-RID-AVS-MAX These information here is simultaneously reset to zero. Information must be reset to zero by pressing the MODE 2 button for 5 sec. Watch out: Take care that the exact information to be reset is on display.
. Troubleshooting GB This chart outlines possible malfunctions, their causes and solutions. malfunction irregular LCD readout (i.e.
GB 18. Warranty We warrant VDO CYTEC models (sensor, computer head and handlebar holder) to the original purchaser for five years from date of C 08 purchase against defects in material and workmanship. This does not cover the batteries and defects resulting from normal wear and tear, improper care, accidents, abuse or alteration. Please take care to retain your receipt of purchase. In case of legitimate complaints, you are entitled to receive a comparable replacement model.
