ENGLISH M1 WR Installation video Operating video Settings video www.vdocyclecomputing.
M1 WR Preface Congratulations In choosing a VDO computer, you have opted for high-quality device with first rate technology. To optimally use the computer, we recommend that you read this manual carefully. It contains full operating instructions and many useful tips. We hope you enjoy cycling with your VDO computer.
M1 WR Display The VDO M1 WR has a large, easy-to-read display that can be divided into three areas. – The top line of the display shows the value for the selected function. – The middle line displays “am” or “pm” if the 12-hour clock format is used. It also displays whether kmh or mph has been selected for the speed indicator. – The bottom line of the display shows the name of the selected function in clear text. TOP MIDDLE BOTTOM Only ONE function at a time appears on the display.
M1 WR Functions The VDO M1 WR has the following functions Current speed With a wheel circumference of 2,155 mm, the maximum possible speed is 199 kmh or 124 mph. Current distance The current distance counts up to 999.99 km or miles. If this maximum value is exceeded, the counter restarts the current distance calculation at zero. Current ride time The current ride time counts up to 99:59:59 HH:MM:SS. If this value is exceeded, the ride time counter restarts at zero.
M1 WR Operation while cycling While cycling, the display functions can be accessed by pressing the BIKE button. Pressing the BIKE button shows the next function on the display. SET Only ONE function at a time is shown on the display. To once again display the speed, the SET button must be pressed. The SETTINGS can also be used to enable the automatic return to the speed indicator from all function displays.
M1 WR Attaching the bracket and the sensor Start by attaching the sensor and the magnet. SENSOR 1 STEP 1 Place the rubber shim under the sensor. Attach the sensor to the fork side that corresponds to the side on which you later want to attach the computer to the handlebars (right or left) using the cable ties supplied (loosely at first, do not pull tight just yet). ATTENTION: the sensor mark on the sensor should point to the spokes.
M1 WR Inserting the computer into the bracket The VDO twist-click system securely connects the computer to the handlebar bracket. How to insert the computer: STEP 1 Place the computer into the bracket in a 10 o’clock position. STEP 2 Rotate the computer to the right into the 12 o’clock position and click it into the bracket system. A noticeable resistance must be overcome to move it into place. Lock UnLock 1. Lock 2. Click STEP 3 To remove the computer, rotate it to the left (without pushing or pulling).
M1 WR Settings – language The following display languages can be selected for the VDO M1 WL: – German – English – French – Italian – Spanish – Dutch – Polish How to select the language: Press and hold the SET button until the settings menu opens. “Language” appears on the display. Press SET to open the language setting. English flashes. You can now press the BIKE button to select a different language. Press the SET button to confirm your language setting. The response “Set Ok” appears on the display.
M1 WR Settings – wheel circumference You can set the roll circumference of your wheel on the VDO M1 WR. The more accurate this setting, the more accurate your speed indicator and the measurement of the distance you have travelled. You can find the values for your wheels in the wheel size table and set these in the device. If your wheel size is not listed in the table, you can accurately measure the roll circumference.
M1 WR Settings – wheel circumference How to set your wheel circumference: Press and hold the SET button until the settings menu opens. “Language” appears on the display. Press the BIKE button to scroll to the setting for the wheel circumference. Press the SET button to open the setting for the wheel circumference. The first two digits flash. Press the BIKE button to set these digits to the desired value. Press the SET button to confirm your setting. The third digit now flashes and is ready to be set.
M1 WR Settings – wheel circumference Press the SET button to confirm your setting. The final digit on the right now flashes. Press the BIKE button to set this digit. Press the SET button to confirm your setting. Your wheel circumference setting is now complete. The response “Set Ok” appears on the display. If you want to configure further settings, press the BIKE button to access these. If you do not want to configure any other settings, press and hold the SET button. The settings menu closes.
M1 WR Settings – unit Use the unit settings to specify whether the speed should be displayed in kmh or mph. Press and hold the SET button until the settings menu opens. “Language” appears on the display. Press the BIKE button to scroll to the setting for the unit. Press the SET button to open the unit setting. “KMH” flashes in the top line of the display. Press the BIKE button to change the unit to “MPH”. Press the SET button to confirm the setting. The response “Set Ok” appears on the display.
M1 WR Settings – clock In the VDO M1 WR, you can set the clock in 12-hour AM/PM format or 24-hour format. Press and hold the SET button until the settings menu opens. “Language” appears on the display. Press the BIKE button to scroll to the setting for the clock. Press the SET button to open the setting for the clock. To switch to the 12-hour AM/PM format, press the BIKE button.
M1 WR Settings – clock Setting the time in 24-hour format Press the SET button to confirm the selection “24”. The hours now flash on the display. Press the BIKE button to set the hours. Press the SET button to confirm the hour setting. The minutes then flash. Press the BIKE button to set the minutes. Press the SET button to confirm the minute setting. The response “Set Ok” appears on the display. If you want to configure further settings, press the BIKE button to access these.
M1 WR Settings – clock Setting the time in 12-hour AM/PM format Press the SET button to confirm the selection “12”. The hours now flash and “am“ or “pm” appears on the display. Press the BIKE button to set the hours. The display information changes from “pm” to “am”. Press the SET button to confirm the hour/AM-PM setting. The minutes now flash on the display. Press the BIKE button to set the minutes. Press the SET button to confirm the minute setting. The response “Set Ok” appears on the display.
M1 WR Settings – speed indicator settings Here, you can set whether the speed indicator should automatically be displayed after a few seconds when in any other display function. This is done as follows: Press and hold the SET button until the settings menu opens. “Language” appears on the display. Press the BIKE button to scroll to the setting for the speed indicator. “Auto Speed” appears on the display. To access the setting, press the SET button. The setting opens.
M1 WR Settings – setting the total distance You can set the total distance ridden on the VDO M1 WR. For example, you can enter your data here at the start of a new cycling season. ATTENTION: the M1 WR has a data memory. No data is lost when the battery is replaced. How to set the total distance: Press and hold the SET button until the settings menu opens. “Language” appears on the display. Press the BIKE button to scroll to the setting for the total distance. Press the SET button to open the settings.
M1 WR Resetting trip data after the trip After each trip, you can reset the data for this trip to zero. The VDO M1 WR is then ready for the next trip. ATTENTION: your total distance (total number of kilometres ridden) is not reset to zero. The process is as follows: Press and hold the BIKE button for a few seconds. The text “RESET Tour Data” appears on the display. If you continue to hold down the BIKE button, the trip data is now reset to zero.
M1 WR Low battery indicator The M1 WR has a low battery warning. The text “Computer low” appears on the display. Press the BIKE button to acknowledge this low battery warning. You can keep using the cycle computer for approx. a week. Replace the battery as soon as possible on seeing the low battery warning. Replacing the battery in the computer To ensure your cycle computer is fully functional, we recommend replacing the battery annually.
M1 WR Terms of guarantee VDO Cycle Parts offers a two-year guarantee on your VDO computer, starting from the date of purchase. This guarantee covers material and processing defects on the computer itself, the sensor/transmitter and the handlebar bracket. Cables, batteries and mounting materials are not covered by the guarantee. If your complaint is legitimate, you will receive a comparable replacement device.
M1 WR Troubleshooting Error Possible cause Correction Half segments on the display (e.g.
M1 WR Correct disposal of this product (electrical waste) (To be used in EU countries and other European countries with a separate collection system). The labelling on the product and the relevant literature indicates that it must not be disposed of with normal household waste at the end of its service life. Please dispose of this device separately to other waste so as not to harm the environment or human health through uncontrolled waste disposal.
Cycle Parts GmbH Le Quartier Hornbach 13 67433 Neustadt/Weinstrasse (Germany) +49 (0) 63 21- 95 82 7 - 0 www.vdocyclecomputing.