Full Product Manual

CAUTION – To reduce the risk of injury or property damage:
• Make sure the unit is thoroughly dry before charging or recharging. If the unit has been
submerged, wipe it dry with a soft cloth before opening the end cap. If water leaks into
the charging port, the unit can sustain permanent damage.
• Never place the light face down on any surface when charging.
• Failure to keep the battery charged will cause permanent damage and result in poor
performance.
Charging/recharging using the 120V AC/
USB Charging Adapter
1. Make sure the spotlight is off.
2. Unscrew (counterclockwise) the waterproof end cap on the back of the unit and
remove it.
3. Insert the micro-USB plug of the USB charging cable into the micro-USB charging
port on the back of the spotlight.
4. Insert the regular USB plug of the USB charging cable into the 120V AC/USB
charging adapter.
5. Plug the 120V AC/USB charging adapter into a (powered) standard North American
120 volt 60Hz outlet. The battery/charge status LED indicator will light or flash in
one of three colors (as described in the “Reading the Battery/Charge Status LED
Indicator” section) to indicate the charging status.
6. Charge up to 5 hours or until the battery/charge status LED indicator lights green.
7. When charging is complete, first unplug the 120V AC/USB charging adapter from
the power source, then disconnect the USB charging cable from the adapter and
the spotlight. Store the adapter and cable in a safe place.
8. Replace the end cap on the unit, screwing clockwise until the triangular arrow on
the end cap is pointing to the dot icon on the rear of unit. Make sure it fits securely,
but do NOT overtighten.
Charging/recharging using the 12V DC/USB Charging
Adapter
1. Make sure the spotlight is off.
2. Unscrew (counterclockwise) the waterproof end cap on the back of the unit and
remove it.
3. Insert the micro-USB plug of the USB charging cable into the micro-USB charging
port on the back of the spotlight.
4. Insert the regular USB plug of the USB charging cable into the 12V DC/USB
charging adapter.
5. Insert the 12 volt DC/USB charging adapter into the 12 volt DC accessory outlet of
a vehicle or other functioning 12 volt DC power source. The LED indicator on the
12V DC/USB charging adapter will light green when it is properly plugged into the
12 volt DC power source. The battery/charge status LED indicator will light or flash
in one of three colors (as described in the “Reading the Battery/Charge Status LED
Indicator” section) to indicate the charging status.
Note: Some vehicles require that the ignition be switched to the accessory position in
order to power the accessory outlet.
6. Charge until the battery/charge status LED indicator lights green.
7. When charging is complete, first unplug the 12V DC/USB charging adapter from the
12 volt DC power source, then disconnect the USB charging cable from the adapter
and the spotlight. Store the adapter and cable in a safe place.
8. Replace the end cap on the unit, screwing clockwise until the triangular arrow on
the end cap is pointing to the dot icon on the rear of unit. Make sure it fits securely,
but do NOT overtighten.
Charging/recharging using the USB charging cable and a
device with a USB power port (not supplied)
1. Make sure the spotlight is off.
2. Unscrew (counterclockwise) the waterproof end cap on the back of the unit and
remove it.
3. Insert the micro-USB plug of the USB charging cable into the micro USB charging
port on the back of spotlight.
4. Insert the regular USB plug of the USB charging cable into a device’s functional
USB power port. The battery/charge status LED indicator will light or flash in one
of three colours (as described in the “Reading the Battery/Charge Status LED
Indicator” section) to indicate the charging status.
5. Charge until the battery/charge status LED indicator lights green.
6. When charging is complete, disconnect the USB charging cable from the device’s
USB power port and the spotlight. Store the cable in a safe place.
7. Replace the end cap on the unit, screwing clockwise until the triangular arrow on
the end cap is pointing to the dot icon on the rear of unit. Make sure it fits securely,
but do NOT overtighten.
OPERATING THE SPOTLIGHT
The On/Off Trigger turns the unit on and off, and is also used to choose either the high
or low brightness setting.
CAUTION: Do not operate while charging.
Disconnect the charging cable or adapter, then select the light mode as follows:
• Press the On/Off trigger once to use the spotlight in its high (brightest) setting.
• Press the On/Off trigger again within 5 seconds to use the spotlight in its low
(dimmest) setting.
• Press the On/Off trigger a third time to turn the unit off.
or
• Press the On/Off trigger once to use the spotlight in its high (brightest) setting.
• Press the On/Off trigger again after 5 seconds to turn the unit off.
Note: The battery/charge status LED indicator will light in one of three colors (as described in the “Reading the
Battery/Charge Status LED” section) to indicate the battery status. It is visible through the translucent
waterproof end cap.
OPERATING THE 120 VOLT AC/USB CHARGING
ADAPTER’S USB PORT
Plug the 120 volt AC/USB charging adapter into a (powered) standard North American
120 volt 60Hz outlet. Then simply plug the USB device into the USB outlet and operate
normally.
OPERATING THE 12 VOLT DC/USB CHARGING
ADAPTER’S USB POWER PORT
Plug the 12V DC/USB charging adapter into a vehicle’s 12 volt DC accessory outlet
or other functioning 12 volt DC power source. The LED indicator on the 12V DC/USB
charging adapter will light green to indicate that it is properly connected. Then simply
plug the USB device into the USB outlet and operate normally.
Note: Some vehicles require that the ignition be switched to the accessory outlet position in order to power the
accessory outlet
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher
temperatures. When the unit is not in use, we recommend that the battery is charged at
least every 3 to 6 months.
From time to time wipe the outside of the device with a soft cloth. Do not immerse the
device in water.
Except for the fuse in the 12 volt DC/USB charging adapter, there are no user-
replaceable parts. Periodically inspect the condition of adapters, connectors and wires.
Contact manufacturer to replace any components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a number
of factors including but not limited to the number of recharge cycles, and proper
care and maintenance of the battery by the end user. Contact manufacturer for any
information you may need.
SAFE BATTERY DISPOSAL
Contains a lithium battery, which must be disposed of
properly. Recycling is required. Failure to comply with local,
state and federal regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical
tape to prevent shorting (shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
LITHIUM
RECHARGEABLE
WATERPROOF
LED SPOTLIGHT
INSTRUCTION MANUAL
3
4
5
6
8
7
2
1
9
10
11
12
14
13
15
16
FL5W10V
SAVE THIS INSTRUCTION MANUAL FOR FUTURE
REFERENCE.
© 2020 Baccus Global LLC
Boca Raton, FL 33487
[phone]
BC
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void
user’s authority to operate the equipment.
SAFETY GUIDELINES /
DEFINITIONS
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous
situation which, if not avoided, may result in property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic
safety precautions should always be followed to reduce the risk of personal injury.
Improper operation, maintenance or modification of tools or equipment could result in
serious injury and property damage. There are certain applications for which tools and
equipment are designed. Manufacturer strongly recommends that this product NOT be
modified and/or used for any application other than for which it was designed. Read and
understand all warnings and operating instructions before using any tool or equipment.
READ ALL
INSTRUCTIONS
WARNING: Read all instructions before operating this worklight. Failure to
follow all instructions listed below may result in electric shock, fire and/or serious
injury.
IMPORTANT SAFETY
INSTRUCTIONS
GENERAL SAFETY WARNINGS AND
INSTRUCTIONS
WARNING – Risk of fire, electric shock, burst hazard, or injury to persons
– when using electrical appliances, basic precautions should always be followed,
including the following:
• LED gets HOT quickly!
• Do not touch the LED at any time when operating.
• Only contact trigger when turning on.
• Do not touch hot lens or enclosure.
• Do not remain in light if skin feels warm.
• Do not operate the spotlight with a missing or damaged lens or enclosure.
• The spotlight and the supplied charging adapters are not toys and cannot be played
with as toys. To reduce the risk of injury, close supervision is necessary when these
units are used near children.
• Use only attachments recommended or sold by the manufacturer.
WARNING – To reduce the risk of electric shock:
• Use only the chargers supplied by the manufacturer to charge and recharge.
• When an extension cord is used:
– The marked rating of the detachable power supply cord or extension cord should
be at least as great as the electrical rating of this appliance.
– The cord should be arranged so that it will not drape over the countertop or
tabletop where it can be tripped over, snagged, or pulled on unintentionally
(especially by children).
– The extension cord should be kept dry and off the ground.
• Do not store the unit or chargers outdoors.
• Charge indoors only. Do not expose chargers to water or any other liquid
WARNING – Fire hazard:
• Never contact combustible material to the lens.
• Keep spotlight lamp away from materials that may burn.
CAUTION – To reduce the risk of injury or property damage:
• All lights give off heat:
– Do not touch lens while operating.
– Keep combustibles away from spotlight lens. Extreme heat can cause fires.
– Never place the light face down on any surface when lit, charging or not in use.
Never store the light face down on any surface.
• Never look directly into the light or shine the light into another person’s eyes. Serious
eye injury could occur.
• Keep sharp objects away from lens — it can crack or break.
• Do not expose this unit to extremely high temperatures.
• Do not drop or throw spotlight. It contains a lithium battery.
• Use only with either the AC or DC charging adapter and USB charging cable that
are provided with unit. Plug in the charging cable at the light first, then plug into the
charging source.
• After charging/recharging, disconnect charging adapter or extension cord and wait 5
minutes before use.
• Do not crush, cut, pull or expose charging adapter cords to extreme heat.
• Position charging adapter cords so they do not become entangled or become a safety
hazard. Keep charging adapter cords away from sharp edges.
• There are no user-serviceable parts inside. Do not attempt to disassemble any other
parts of the unit.
• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting.
• Do not attempt to charge the unit if the charger or cord is damaged – return the charger
to manufacturer for repair or replacement.
SPECIFIC SAFETY INSTRUCTIONS FOR
LITHIUM BATTERIES
WARNING – To reduce the risk of fire, electric shock, burst hazard, or injury
to persons or property:
Lithium batteries are small, compact and ideal for providing long-lasting power to this
unit. However, they must be used and charged properly. Improper use can result in
serious injury, fire, or death.
• Lithium batteries can explode in the presence of a source of ignition. Do not use the
product in the presence of an open flame.
• Do not place this lithium battery powered unit in fire or apply heat to it.
• Do not subject this lithium battery powered unit to strong impacts or shocks. The
battery in this unit contains safety and protection devices which, if damaged, may cause
the battery to generate heat, rupture or ignite.
• Do not expose this lithium battery powered unit to water or salt water, or allow the
battery to get wet.
• Avoid storing this lithium battery powered unit in the basement, bathroom or other areas
of the house that are or may become wet or humid or where moisture may concentrate.
• Do not leave this lithium battery powered unit in direct sunlight, or use or store the unit
inside cars in hot weather. Doing so may cause the battery to generate heat, rupture, or
ignite. Using the battery in this manner may also result in a loss of performance and a
shortened life expectancy.
• Never charge this unit near heat or flammable objects.
• NEVER THROW WATER ON A BURNING LITHIUM BATTERY! If
a lithium battery does catch on fire, it will burn even more violently if it comes in
contact with water or even moisture in the air. A fire extinguisher must be used.
Battery Charging and Capacity
This unit is delivered in a partially charged state – you must fully charge it before using
it for the first time.
When stored at room temperature with a full charge, lithium batteries will will begin to
discharge from the time they are manufactured, even when unused. Deep discharges
also decrease their capacity. Battery life can be extended by the following:
• Charge battery to full capacity before storage.
• Optimal storage temperature for this unit is between 5°C and 20°C (41°F and 68°F).
• Never discharge the battery fully.
• Charge after each use.
• Always charge at least once every 3-6 months if not in frequent use to prevent
overdischarge.
Transportation of Lithium Batteries
• Always check all applicable local, national, and international regulations before
transporting a unit containing a lithium battery.
• Transporting an end-of-life, damaged, or recalled battery may, in certain cases, be
specifically limited or prohibited.
INSTRUCTIONS PERTAINING TO
WATERPROOF SPOTLIGHTS
The rubber O-ring acts to preserve the waterproof qualities of the spotlight. The O-ring
seals the end cap to prevent water from entering the gap. An undamaged rubber O-ring,
rubber bezel and lens, and proper sealing of the end cap before use are very important.
CAUTION – TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Attempting to remove the rubber O-ring; use of the unit with a damaged O-ring, rubber
bezel or lens; improper sealing of the waterproof end cap; and/or submerging this unit
in depths greater than 6 feet may cause the unit to no longer be waterproof. Do not
submerge the unit if these conditions exist or the unit could sustain permanent damage.
• Submerging this unit in depths greater than 6 feet and/or operating it in water
temperature other than between 41ºF and 104ºF (5ºC and 40ºC) could result in leakage,
warping or malfunction, causing permanent damage to the spotlight.
INSTRUCTIONS PERTAINING TO THE 12V DC/
USB CHARGING ADAPTER
CAUTION – TO AVOID THE RISK OF PROPERTY DAMAGE:
• NEVER CONNECT THE UNIT TO A POSITIVE GROUNDED VEHICLE.
• The 12 Volt DC charging adapter must only be connected to batteries with a nominal
output voltage of 12 volts. The unit will not operate from a 6 volt battery and will sustain
permanent damage if connected to a 24 volt battery.
• Always connect the 12 volt DC/USB charging adapter to the 12 volt DC power source
before plugging any devices into it
INSTRUCTIONS PERTAINING TO THE USB
PORTS
• IMPORTANT: Some household USB-powered electronics will not operate with the
USB ports provided with this device. Check the manual of the corresponding electronic
device to confirm that it can be used with this type of USB port.
• The USB ports do not support data communication. They only provide power to an
external USB powered device (5VDC/2.1A using the USB port on the DC /USB charging
adapter or 5VDC/1A using the AC/USB charging adapter). Make sure the rating of
equipment plugged into the USB port does not exceed the amperage stated.
• Always connect the appropriate charging adapter to either the 120 volt AC or 12 volt DC
power source before plugging any devices into it.
• Do not attach USB hubs allowing connection of multiple personal electronic devices to
any of the USB ports on the charging adapters.
SAVE THESE
INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new Vector
®
Spotlight. Read this Instruction
Manual and follow the instructions carefully before using your new spotlight.
READING THE BATTERY/CHARGE STATUS LED
INDICATOR
The Battery and Charging Status LED indicator is located directly above the Micro-USB
Charging Port under the Waterproof End Cap on the back of the unit.
DOT ICON
(ALIGNS TO THE
TRIANGULAR
ICON ON THE
END CAP)
TRIANGULAR
ARROW
ICON (ALIGNS
TO THE DOT
ICON ON THE
REAR OF
THE UNIT)
END CAP DETAIL
It lights or flashes in three colors to indicate the following:
When charging:
Green: Battery is in a fully charged state.
Green (flashing): Battery is in a high partially charged state.
Orange (flashing): Battery is in a low partially charged state.
Red (flashing): Battery needs to be recharged.
Red (flashing rapidly): The battery of the unit is overheated due to extensive use
or recharging. The charging process will stop at this stage and will automatically resume
after a cool down period.
When operating:
Green: Battery is operating at full voltage.
Orange: Battery is operating at partial voltage.
Red: Battery is operating at low voltage, and should be recharged or the built-in low
voltage protection will be activated and the unit will automatically shut down shortly.
Red (flashing rapidly): The battery of the unit is overheated (due to extensive
use or recharging), or is too cold (the ambient temperature has dropped below -20°C).
Operation will stop at this stage.
CHARGING/RECHARGING THE SPOTLIGHT
This unit is shipped in a partially charged state. Charge unit after purchase and BEFORE
first use until the battery/charge status LED indicator lights green.
Recharge after each use until the battery/charge status LED indicator lights green.
IMPORTANT: When the unit is not in use, we recommend that the battery is charged
at least every 3 to 6 months.
Replacing the Fuse in the 12V DC/USB Charging Adapter
2A FUSE
CENTER CONTACT
END CAP
1. Unscrew the end cap counterclockwise
and remove.
2. Remove center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 2
amp fuse.
5. Replace the fuse, center contact and
end cap.
6. Screw end cap clockwise until it is
finger tight – DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12 volt
DC/USB charging adapter.
TROUBLESHOOTING
The spotlight will not charge
• Check that the spotlight is turned off.
• Check that the USB charging cable is properly connected to either the 12V DC/USB
charging adapter or the 120V AC/USB charging adapter, and to the spotlight.
• Check the connection to the AC or DC power source. Make sure there is good contact.
• Confirm that there is functioning AC or DC current.
• Check the plug fuse in the 12V DC/USB charging adapter. Replace the fuse following the
instructions in this manual, if necessary.
• The unit may have shut down to protect the battery from overheating after a long period
of operation or charging. Unplug the charging adapter from the power source and
disconnect the USB charging cable from the spotlight. Allow the spotlight to cool down
for a period before resuming charging.
The spotlight will not operate
• Make sure the On/Off Trigger has been pressed to turn the spotlight on.
• The unit may have shut down to protect the battery from overheating after a long period
of operation or charging; or the ambient temperature has dropped below –20°C. Allow
the spotlight to cool down or warm up for a period before resuming operation.
• If the ambient temperature is too hot or too cold the spotlight will not operate.
• The internal battery may be completely discharged. Charge the unit following the
directions given in this manual.
The 120V AC/USB charging adapter’s USB port will not operate
• Make sure you have live AC power to the outlet the 120V AC/USB charging adapter is
plugged into.
• Make sure the rating of equipment plugged into the charging adapter’s USB port does
not exceed 1A continuous.
• Some household USB-powered electronics will not operate with this USB port. Check
the manual of the corresponding electronic device to confirm that it can be used with
this type of USB port.
The 12V DC/USB charging adapter’s USB port will not
operate / LED indicator on the 12V DC/USB charging adapter
does not come on
• Check the connection to the 12 volt DC power source. Make sure there is good contact.
• Confirm there is functioning DC current.
• Check the plug fuse in the 12V DC/USB charging adapter. Replace the fuse following
the instructions in this manual, if necessary.
• Make sure the rating of equipment plugged into the charging adapter’s USB port does
not exceed 2.1A continuous.
• Some household USB-powered electronics will not operate with this USB port. Check
the manual of the corresponding electronic device to confirm that it can be used with
this type of USB port.
If the unit does not charge or operate after taking the steps given above, contact the
manufacturer at [phone].
ACCESSORIES
Recommended accessories for use with your tool may be available from the
manufacturer. If you need assistance regarding accessories, please contact the
manufacturer at [phone].
WARNING: The use of any accessory not recommended for use with this appliance
could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact
the manufacturer at [phone].
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and workmanship
for a period of ONE (1) YEAR from the date of retail purchase by the original end-user
purchaser (“Warranty Period”).
If there is a defect and a valid claim is received within the Warranty Period, the defective
product can be replaced or repaired in the following ways: (1) Return the product to
the manufacturer for repair or replacement at manufacturer’s option. Proof of purchase
may be required by manufacturer. (2) Return the product to the retailer where product
was purchased for an exchange (provided that the store is a participating retailer).
Returns to retailer should be made within the time period of the retailer’s return policy
for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be
required. Please check with the retailer for their specific return policy regarding returns
that are beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting
from normal wear and tear, accidents; damages sustained during shipping; alterations;
unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for
care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may
have other rights which vary from state to state or province to province. This product is
not intended for commercial use.
Please visit our website www.baccusglobal.com/register to register your new Baccus
Global LLC product and to be kept up to date on new products and special offers.
SPECIFICATIONS
Light (Conforms to UL STD. 73)
Bulb: 5 watt LED bulb
Battery: Lithium, 3.6V DC
Input: 5V DC, 1A (120 Volt AC/USB Charging Adapter) or
2.1A (12 Volt DC/USB Charging Adapter)
120V AC/USB Charging Adapter (Conforms to UL STD. 62368-1)
(Optional Accessory)
Input: 120V AC, 60Hz, 6.7W
Output: 5V DC, 1A
12V DC/USB Charging Adapter (Conforms to UL STD. 2089)
(Optional Accessory)
Input: 12V DC, 1.1A
Output: 5V DC, 2.1A
Fuse: 2A
Imported by Baccus Global LLC,
621 NW 53rd St., Suite 450, Boca Raton, FL 33487
www.Baccusglobal.com 1-877-571-2391
RD120320
FEATURES (refer to the above numbered diagram)
1. LED bulb
2. Rubber bezel
3. On/off trigger
4. Grip handle
5. Micro-USB charging port (for use with the USB Charging Cable and Charging
Adapters)
6. Battery/charge status LED indicator
7. Translucent waterproof end cap (see detailed view in the “Reading the Battery/
Charge Status LED Indicator” section)
8. Rubber O-ring
9. USB charging cable (for use with 12V DC/USB Charging Adapter and 120V AC/
USB Charging Adapter)
10. Regular USB plug
11. Micro-USB plug
12. 12V DC/USB Charging Adapter (Optional Accessory)
13. 12V DC/USB Charging Adapter LED Indicator
14. 12V DC/USB Charging Adapter USB Port (Optional Accessory)
15. 120V AC/USB Charging Adapter (Optional Accessory)
16. 120V AC/USB Charging Adapter USB Port (Optional Accessory)
FL5W10V_ManualENSP_120320.indd 1FL5W10V_ManualENSP_120320.indd 1 12/3/2020 11:22:16 AM12/3/2020 11:22:16 AM