VEC021/021AC INDUSTRIAL SERIES ™ 900 JUMPSTART SYSTEM & POWER SUPPLY PORTABLE, CORDLESS, RECHARGEABLE 12-VOLT DC* POWER SUPPLY COMPLETELY PORTABLE, SAFE & CONVENIENT *INCLUDES INSTRUCTIONS FOR 110-VOLT AC POWER OPTION (MODEL VEC023 INVERTER: INCLUDED WITH MODEL VEC021AC; NOT INCLUDED WITH MODEL VEC021) THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT.
TABLE OF CONTENTS FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. USING 2.1 2.2 2.3 THE INDUSTRIAL 900™ AS A JUMPSTART SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . Easy, Step-by-Step Jumpstarting Instructions . . . . . . . . . . . .
i ii WARNINGS WARNING STATEMENTS IDENTIFY CONDITIONS OR PRACTICES THAT MAY RESULT IN PERSONAL INJURY OR LOSS OF LIFE. • WHEN WORKING WITH LEAD ACID BATTERIES, ALWAYS MAKE SURE IMMEDIATE ASSISTANCE IS AVAILABLE IN CASE OF ACCIDENT OR EMERGENCY. • ALWAYS USE PROTECTIVE EYEWEAR WHEN USING THIS PRODUCT: CONTACT WITH BATTERY ACID MAY CAUSE BLINDNESS AND/OR SEVERE BURNS, BE AWARE OF FIRST AID PROCEDURES IN CASE OF ACCIDENTAL CONTACT WITH BATTERY ACID.
iii Congratulations 1 VEC021/VEC021AC INDUSTRIAL SERIES™ 900 JUMPSTART SYSTEM & POWER SUPPLY on selecting the Vector™ INDUSTRIAL SERIES™ 900 JUMPSTART SYSTEM & POWER SUP- PLY. Please read this guide carefully before use to ensure optimum performance and avoid damage to the unit or items that you are using it with. Figure 1. 2. In addition to a built-in 12-volt power supply, the INDUSTRIAL 900™ JUMPSTART SYSTEM has several exclusive features that set it apart from other similar devices.
2 3 IMPORTANT INFORMATION: Figure 4. Figure 3. 1. 1. 4 2. 2. 3. 3. 1. FIXED CLAMP COVER 2. CLAMP HOLSTER SHOULDER 3. SLIDE DOWN & ROTATE CLAMP OUTWARD FROM BACK OF UNIT TO REMOVE 5. 1. 2. 3. 4. INVERTER POWER INDICATOR INVERTER ON/OFF SWITCH INVERTER OVERLOAD/LOW BATTERY INDICATOR STANDARD HOUSEHOLD-TYPE 110-VOLT AC POWER SOCKET 5. 12-VOLT DC CIGARETTE LIGHTER TYPE PLUG FEATURES: • Heavy duty, INDUSTRIAL SERIES™, professional quality • Provides INSTANT POWER—whenever, and wherever it’s needed.
5 4 1. INTRODUCTION 2. USING THE INDUSTRIAL 900™ AS A JUMPSTART SYSTEM The Vector™ INDUSTRIAL SERIES™ 900 JUMPSTART SYSTEM & POWER SUPPLY is a compact, durable and portable jump start system for vehicles and boats that have a standard 12-volt DC battery system. This self-contained, rechargeable system will start most vehicles and boats without the need for a host vehicle or 110-volt AC power supply.
6 7 NOTE: In the rare event that the vehicle to be started has a Positive Grounded System (positive battery terminal is connected to chassis): Replace steps I and 2 above with the following steps, and then proceed to steps 4-6 above. 1. Connect negative (-) black clamp to vehicle battery ‘s negative terminal. 2. Connect positive (+) red clamp to vehicle chassis or a solid, non-moving, metal vehicle component or body part. DO NOT clamp directly to positive battery terminal or moving part.
9 WARNING: DO NOT RECHARGE FOR MORE THAN 3-4 HOURS MAXIMUM USING 12-VOLT DC METHOD. 1. NOTE: If unit is fully discharged, it is recommended that the vehicle being used for recharging be left running while the unit is being charged via the 12-volt DC method. 2. Insert one end of the DC/DC charging cord into the 12-volt DC cigarette lighter receptacle on the vehicle or boat. See Fig. 5 #3. 3. Insert the plug at the other end of this power cord (Fig.
10 11 CAUTION: RECHARGEABLE APPLIANCES Certain rechargeable devices are designed to be recharged by plugging them directly into an AC receptacle. These devices may damage the Power Force 150™. When first using a rechargeable device, monitor its temperature for the initial ten minutes of use to determine whether it emits excessive heat. If excessive heat is detected, it is a good indication that the device should not be used with this inverter.
12 To ensure years of reliable service, the power inverter must be installed and used properly. Please read the installation and operating instructions thoroughly prior to installation and use. Pay particular attention to the CAUTION and WARNING statements in this manual. The CAUTION statements advise against certain conditions and practices that may result in damage to the INDUSTRIAL 900™ and/or the inverter.
14 15 8.3.5 Placement Of The Power Force 150™ For best operating results, the inverter should be properly installed (as directed in this manual) in the INDUSTRIAL 900™. The combined unit should only be used in locations that meet the following criteria: DRY—Do not allow water or other liquids to come into contact with unit. COOL—Ambient air temperature should be between -20° C and 40° C—ideally between 15° C and 25° C (60 - 80° F).
17 16 8.5.3 Troubleshooting Guide: TROUBLESHOOTING TIPS PROBLEM POSSIBLE CAUSES RECOMMENDATIONS LACK OF 1. Inverter not adequately warmed up. Turn inverter switch OFF, then ON again. Repeat if necessary. Recharge/replace source battery. Reduce load to appropriate maximum for the inverter. Allow inverter to cool down for at least 15 mins. before turning ON again. Replace fuse (see section in this manual). Clean or replace, as necessary, for proper connection. POWER OUTPUT 2.
18 19 1 YEAR LIMITED WARRANTY REGISTRATION FORM This Vector Manufacturing, Ltd. product is warranted to the original purchaser only, for one year from the date of purchase, to be free of defects in materials and workmanship. In no event will Vector Manufacturing, Ltd. be responsible for any amount of damages beyond the retail purchase price of the product. All Vector Manufacturing, Ltd. products must be registered within (10) days of purchase.