VEC118S 1,500,000 CANDLEPOWER CORDED, CORDLESS RECHARGEABLE SPOTLIGHT WITH BUILT-IN AREA LIGHT OWNER’S MANUAL & WARRANTY INFORMATION THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USING, READ AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS, PLUS YOUR VEHICLE'S BATTERY MANUFACTURER GUIDELINES. FAILURE TO DO SO COULD RESULT IN INJURY AND/OR PROPERTY DAMAGE. 4140 SW 28th Way, FT.
IMPORTANT SAFETY INSTRUCTIONS WARNINGS: Contains non-spillable, sealed, lead acid battery. Must be recycled or disposed of properly. DO NOT dispose of batteries in fire, as this may result in an explosion. DO NOT open battery or short circuit, as this may cause the battery to leak or get hot, causing personal injury. Any disposal questions call toll-free (877) 288-7722. Please read instruction manual completely for all safety and warning instructions.
1. INTRODUCTION Congratulations on purchasing VectorLiteTM Model VEC118S, an advanced design combination spotlight and long lasting, soft incandescent area light. It uses two powerful proven-technology rechargeable, non-spillable, sealed, lead acid batteries that allow for years of dependable use, recharge after recharge. It was designed from the ground up to be the most versatile and practical light for travel, camping, picnicking, tailgate parties and boating.
3. OPERATION The trigger switch is squeezed to turn on the spotlight. This provides momentary operation. The trigger switch may be locked in the ON position to provide continuous light without continuously squeezing the trigger switch. To lock the trigger switch ON, move the trigger lock to the up position. After use, move the trigger lock down (OFF) and release the trigger switch. Store the spotlight with the trigger switch OFF and the trigger lock ON.
4. CHARGING THE VECTORLITE USING AC RECHARGE ADAPTER 1. Locate the recharge port on the side of the spotlight (see figure 1). 2. Connect the charger to an appropriate AC power source. 3. Plug the charger's barrel connecter into the recharge port located near the handle. Note that the red LED lights to indicate that the battery is charging. 4. Recharge for 12 hours maximum. 5. After recharge, disconnect the adapter from the external charging source, then disconnect barrel connector from the recharge port. 6.
5. PERIODIC MAINTENANCE All batteries lose charge over time, especially when they are warm. AC recharge is recommended every two months, when not in frequent use. Use the AC recharger and charge for the recommended time. If the unit has dirt on it, gently clean the outer surfaces of the spotlight unit with a soft cloth moistened with a mild solution of water and detergent. Periodically inspect the condition of recharge adapters, connectors, and wires.
FIGURE 3A REFLECTOR ASSEMBLY RETAINING RING RUBBER BEZEL RUBBER”O”Open RING GLASS LENS PHILLIPS SCREW Closed Open HAIRPIN RETAINING WIRES FIGURE 3B Closed SCREW 10. Insert the replacement bulb into the reflector's flange. 11. Put back and secure the hairpin retaining wires. 12. Connect the white bulb power wire to the red power wire. 13. Tighten the retaining screw on the flange. 14. Place the reflector in position in the body of the spotlight. 15.
REPLACING THE BATTERIES The rechargeable, sealed, lead acid batteries have a life of several years, if recharged promptly after each use. When the fully charged batteries only provide about 10 minutes or less of spotlight operation, they should be replaced with new batteries. To replace the batteries, you will need the Phillips type screwdriver and replacement batteries (Vector Part VEC191). The batteries are in compartments referred to as upper and lower.
WARNINGS: DO NOT ALLOW BARE WIRES OR CONNECTORS TO CONTACT EACH OTHER DANGEROUS SPARKING CAN OCCUR - NOTE WHICH WIRES ARE ON THE BATTERY TERMINALS 6. Note position of battery. Note which wire is on which terminal. 7. Disconnect the wires from the battery and set the battery aside. 8. Connect the replacement battery, making sure the correct wires are on the new battery terminals. Make sure POS (+) is red and NEG (-) is black.
TWO YEAR LIMITED WARRANTY PROGRAM This limited warranty program is the only one that applies to this product, and it sets forth all the responsibilities of Vector Manufacturing, Ltd., regarding this product. There is no other warranty, other than those described herein. This Vector Manufacturing, Ltd. product is warranted, to the original purchaser only, to be free of defects in materials and workmanship for two years from the date of purchase without additional charge.