V E C T R ON S Y S T EMS Vec t r on P O S S t eel Touch II Use r m a n u a l
Your Vectron dealer Stamp Date: 18.08.2011 © 2011 by Vectron Systems AG Subject to error and technical modification Manufacturer Vectron Systems AG Willy-Brandt-Weg 41 48155 Muenster, Germany www.vectron.
C on t en t s 1. Terms, signs and symbols.................................................. 11 1.1. 1.1.1. 1.1.2. 1.1.3. 1.2. 2. 3. General notes on safety..................................................... 15 About this manual. . ............................................................. 17 3.1. 3.2. 3.3. 3.4. 4. Target group.................................................................................... 17 Purpose...............................................................................
V E C T RON P O S S T EELT OUC H II 6. Starting.. .............................................................................. 41 6.1. 6.2. 6.3. 6.4. 7. Connecting SteelTouch II to the power supply. . .......................... 42 Setting up the SteelTouch II.......................................................... 44 Adjusting the display...................................................................... 44 Connecting devices to SteelTouch II.. ...........................................
10. Service and maintenance................................................... 72 10.1. 10.2. 10.2.1. 10.3. 10.4. Cleaning . . .......................................................................................... 72 Cleaning housing and display........................................................ 73 Cleaning the contacts. . ................................................................... 73 Maintenance. . ...................................................................................
V E C T RON P O S S T EELT OUC H II 17.2. 17.2.1. 17.2.2. 17.2.3. 17.2.4. 17.3. 17.3.1. 17.3.2. 17.3.3. 8 Mobile / hybrid Vectron POS systems.......................................... 93 Vectron POS MobilePro.................................................................. 93 Vectron POS MobileTouch.............................................................. 94 Vectron POS MobileXL . . .................................................................. 95 Vectron POS MobilePad.. ........................
1. Ter ms, signs and s y mbols This chapter informs you about the terms, signs and symbols that are used in this user manual. 1 .1 . N otes o n s afe t y This user manual contains safety notes, which indicate hazards when operating the Vectron POS SteelTouch II, in the following referred to as SteelTouch II. Each safety note consists of three elements, the signal word (1), the word message (2) and the safety symbol (3). 1 EN 3 2 Fig.
V E C T RON P O S S T EELT OUC H II 1 .1 .1 . Si g n a l wo rd s Signal words inform you about the risk of danger. The risk contains information on how serious injuries are and how probable it is that an injury will occur. A ADANGER The signal word “DANGER” indicates a danger with high risk, which will result in death or severe injury if it is not avoided. A AWARNING The signal word “WARNING” indicates a danger with medium risk, which could result in death or severe injury if it is not avoided.
1 .1 . 2 . Wo rd m es s a g e Information of the word message for personal injury appear in the same order in every safety note. Risk of electric shock • • High voltage at the power supply X X Do not open power supplies You will die or suffer from burns X X Only use undamaged power supplies The word message contains the following information: • You are told what is dangerous. • You are told what endangers you and where the danger is located. • You are told what you must not do.
V E C T RON P O S S T EELT OUC H II 1 .1 . 3 . S afe t y sy m b o l s Each safety note contains a safety symbol, which marks the hazard graphically. If no special safety symbol is available, the general safety symbol is used. Safety symbols have the following meaning: Safety symbol A A a s q 1. 2. Meaning General safety symbols for signal word panels, warning of personal injuries. General safety symbol for hazards for which no special safety symbol is available.
2. G ener al no t e s on s a f e t y This chapter informs you about hazards that exist when operating the SteelTouch II.
V E C T RON P O S S T EELT OUC H II NOTICE a 16 Damage of SteelTouch II • • Dropping of SteelTouch II from the set-up area • • Transport and dispatch of SteelTouch II in inappropriate packaging • • Overvoltage in power supply network • • Overvoltage through connection of a wrong power supply The SteelTouch II could be damaged X X Place the SteelTouch II on a stable, even surface with sufficient space X X Keep the original packaging X X Transport and dispatch the SteelTouch II exclusively in the original
3. A bou t t his manual This user manual is part of the SteelTouch II. The user manual must be kept together with SteelTouch II. When forwarding the SteelTouch II please forward this manual as well. 3 .1 . Ta rg e t g ro u p This user manual is meant for end users of the SteelTouch II. 3.2. P u r p os e This user manual informs you about performance and features of the SteelTouch II. It is meant to inform you about how to start, operate and close down the SteelTouch II. 3.3.
V E C T RON P O S S T EELT OUC H II For this reason, this end user manual contains only the information that applies for all SteelTouch II POS systems, since the Vectron POS software should be programmed and configured individually for you. This end user manual does not contain information about programming and configuration of the SteelTouch II POS system.
The “EC Declaration of conformity” certifies the guidelines with which SteelTouch II complies and according to which standards the SteelTouch II was built. The “Document revision” registers modifications of the user manual’s content. The chapter “Accessories” informs you about additional products that you can buy and use together with SteelTouch II . The chapter “Other Vectron products” informs you about other products, which Vectron offers in addition to SteelTouch II .
V E C T RON P O S S T EELT OUC H II 4. Speci f ic a t ion This chapter informs you about the features, the technical data and the intended use of SteelTouch II. SteelTouch II is a stationary POS system that consists of three components: the stationary POS system, the stand and the power supply Vectron PS30. 4 .1 . Ste e lTo u ch I I P OS sys te m SteelTouch II is a stationary POS system, which you can also use without network connection.
Your Vectron dealer can integrate the SteelTouch II via network interface to a POS system network, so that the SteelTouch II can receive data via the network and send data to other POS systems. A loudspeaker is integrated to the housing of SteelTouch II. SteelTouch II uses sounds to inform you about received messages, which were sent eg by a ServiceCall. Please ask your Vectron dealer to configure the sounds for you. At the rear of SteelTouch II you find a bracket with ports.
V E C T RON P O S S T EELT OUC H II 4 . 2 . Ve c tro n - P OS-S of t wa re SteelTouch II is supplied with Vectron POS software, which your Vectron dealer configured and programmed. All Vectron POS systems use the same software. The GUI can be adjusted individually to the different screen sizes of the stationary and mobile POS systems. The functions that can be used with the installed Vectron POS software depend on the applied software version, configuration and programming of the SteelTouch II POS system.
4.3. Us e a s d i re c te d The SteelTouch II may be used as POS system. The power supply Vectron PS30 may be used for supplying the SteelTouch II with power. Use the supplied cable with safety plug to connect SteelTouch II and power supply Vectron PS30 to a grounded socket. Using other power supplies and cables is not as directed. The power supply network must be protected with a residual current device. SteelTouch II and power supply must not be opened.
V E C T RON P O S S T EELT OUC H II You should protect yourself against undesired changes of the above mentioned parts of programming. This can be achieved by using operator keys, RFID cards and passwords. Each operator should be assigned his required authorization in the rights table of the POS system. Operator keys and RFID cards, which enable these rights, must exclusively be accessible to the respective operators. The passwords must exclusively be known by the respective operators.
Operation of SteelTouch II is exclusively allowed with Vect ron original accessories or accessories approved by Vect ron. Your Vectron dealer will inform you about accessories that you can use together with the SteelTouch II. Keep the packaging material for dispatch purposes. Send the SteelTouch II exclusively in its original packaging. Vec tron Systems AG does not accept liability for damages due to improper packaging. Use as directed also includes the reading and understanding of this user manual.
V E C T RON P O S S T EELT OUC H II 4.4. Te ch n i c a l d a t a This chapter informs you about the technical data of SteelTouch II. 4 . 4 .1 . Ste e lTo u ch I I P OS sys te m Technical data of the SteelTouch II POS system Display diagonal 26 15" 17" 38.1 cm (15") 43.1 cm (17") Display type TFT-LCD Display backlight CCFL backlight Display size (active) 30.4 x 22.8 cm 33.7 x 27.
Technical data of the SteelTouch II POS system 15" 17" Operator socket 3.5 mm jack; for Dallas iButton and Addimat locks SD-card slot for SD-cards up to 4 GB and SDHC-cards up to 32 GB Loudspeaker mono; 2 W Power supply through external power supply Vectron PS30; integrated in stand Buffer battery for permanent power supply of the cache Power consumption 18 W in normal operation without external devices; 0.5 W in standby 33 W in normal operation without external devices; 0.
V E C T RON P O S S T EELT OUC H II 4 . 4 . 2 . P owe r su p p l y Ve c tro n P S 3 0 Technical data of power supply Vectron PS30 Input voltage 100 to 240 V alternating voltage Input current max. 1.07 A Output voltage + 24 V direct current Output current max. 3.3 A Output power max. 80 W Power consumption max. 93 W No-load loss 0.3 to 0.5 W Temperature storage: -40 to 85 °C operation: 0 to 40 °C operation: 5 to 95 %, non condensing Air humidity Dimensions (W x H x D) Weight Certified 7.
5. De v ic e de s cr ip t ion The SteelTouch II comprises the stationary POS system and the stand with power supply Vectron PS30. 5 .1 . S h i p m e nt Shipment of the SteelTouch II POS system comprises the parts listed below. Please check the correct delivery on receipt.
V E C T RON P O S S T EELT OUC H II 5 . 2 .1 . Ste e lTo u ch I I fro nt v i ew 1 2 3 4 Fig. 2: SteelTouch II front view Pos.
Housing pos. 1 Touch screen and electronics of SteelTouch II are mounted in the housing. Touch screen pos. 2 Via the touch screen you enter data to SteelTouch II using a touch pen or your fingers. Operator lock pos. 3 By means of an operator key you log in to the POS system via the operator lock. Stand pos. 4 The power supply Vectron PS30 is mounted in the stand.
V E C T RON P O S S T EELT OUC H II 5 . 2 . 2 . Ste e lTo u ch I I re a r v i ew 2 3 4 5 1 Fig. 3: SteelTouch II rear view Pos.
USB ports pos. 1 Via the USB ports you can connect external devices and storage media to the SteelTouch II. Hinge pos. 2 The hinge connects the housing and the stand of SteelTouch II. It serves for tilting the housing in order to adjust the display to your angle of view. Ports and connections pos. 3 Via the ports, connections and slots you can connect external devices and storage media to the SteelTouch II. Serial number label Pos.
V E C T RON P O S S T EELT OUC H II 5 . 2 . 3 . P o r t s a n d co n n e c ti o n s d e t a i l e d v i ew 1 2 3 4 5 67 8 9 10 Fig. 4: Detailed view of ports and connections Pos. Designation 1 Loudspeaker 2 Six USB ports 3 Network port 4 Six serial ports 5 SD-card slot 6 Audio connection 7 Power connection 8 Two cash drawer ports 9 Operator lock connection 10 SIM-card slot; optional Loudspeaker pos. 1 Via the loudspeaker the SteelTouch II can play eg system sounds.
Network port pos. 3 To the network port you can connect a network cable. Serial ports pos. 4 Via the serial ports you can connect external devices to SteelTouch II. SD-card slot pos. 5 To the SD-card slot you can insert an SD- or SDHC-card, eg for storing data. Audio connection pos. 6 To the audio port you can connect stereo loudspeakers, eg for playing system sounds. Power connection pos. 7 EN The power plug of the Vectron PS30 is connected to the power supply. Cash drawer ports pos.
V E C T RON P O S S T EELT OUC H II 5 . 2 . 4 . P owe r su p p l y Ve c tro n P S 3 0 1 4 2 3 Fig. 5: Power supply Vectron PS30 Pos.
Power cable plug pos. 2 The power cable plug is put into the power connection of SteelTouch II. Female connector pos. 3 The female connector of the power cord is put into the mains plug. Serial number label pos. 4 The serial number label serves for unambiguous identification of the power supply Vectron PS30. The label contains the product designation and the serial no. of the Vectron PS30.
V E C T RON P O S S T EELT OUC H II 5 . 2 . 5 . P owe r co rd 1 2 Fig. 6: Power cord Pos.
Female connector pos. 1 The female connector is put into the mains plug of the power supply. Safety plug pos. 2 The safety plug is put into a socket. The safety plug may differ from the one shown in the figure.
V E C T RON P O S S T EELT OUC H II 5.3. D i m e n si o n s 308 (12.1") 220 (8.7") 386 (15.2") 410 (16.1") 311 (12.2") 50 (2.0") 255 (10.0") 405 (15.9") Fig. 7: SteelTouch II 15" (dimensions in millimetre and inch) 342 (13.5") 220 (8.7") 410 (16.1") 447 (17.6") 311 (12.2") 50 (2.0") 255 (10.0") 439 (17.3") Fig.
6. S t ar t ing This chapter tells you how to start the SteelTouch II. Your Vectron dealer should have programmed and configured the SteelTouch II POS system for your prior to starting. He should support you with the starting. Prior to starting your Vectron dealer should train you with the operation of SteelTouch II. Furthermore he should inform you about the functions of the SteelTouch II POS system and adjust them to your demands.
V E C T RON P O S S T EELT OUC H II 6 .1 . Co n n e c ti n g Ste e lTo u ch I I to th e p owe r su p p l y This chapter tells you how to connect the SteelTouch II to the power supply. • Place the SteelTouch II to a smooth, stable and even surface with sufficient space.
• Lead the power line of the power supply through the recess of the stand. NOTICE a Overvoltage can damage the power supply and the electronics of SteelTouch II X X Check the voltage of the power network X X Connect the SteelTouch II exclusively to power networks with a voltage between 100 and 240 volt • Put the safety plug of the power cord into a socket.
V E C T RON P O S S T EELT OUC H II 6 . 2 . S e t ti n g u p th e Ste e lTo u ch I I This chapter tells you how to set up the SteelTouch II. a NOTICE Damage of SteelTouch II through dropping X X Set up the SteelTouch II as described in this chapter • Set up the SteelTouch II in a well-ventilated room with a temperature between 0 and 40°C for the SteelTouch II 15" and a temperature between 0 and 35°C for the SteelTouch II 17".
A ACAUTION q Risk of crushing • • Small gap between housing and stand X X Do not put fingers between housing and stand You could crush your fingers X X Grasp housing of SteelTouch II with both hands and adjust • Grasp the housing of the SteelTouch II with both hands as shown in the image and adjust the display to your field of vision. EN Fig.
V E C T RON P O S S T EELT OUC H II 6.4. Co n n e c ti n g d ev i ces to Ste e lTo u ch I I This chapter tells you how to connect devices to the SteelTouch II. • Make sure to connect only approved devices to the SteelTouch II. • Make sure to lay out the cables so that they are not under pressure. • Make sure to lay out the cables so that you do not trip over them. 7. Oper a t ion This chapter tells you how to use the SteelTouch II in normal operation. i 7.1 .
7.1 .1 . Swi tch i n g o n th e Ste e lTo u ch I I If the SteelTouch II was started as described in chapter “6. Starting” on page 41, you can switch it on. • Shortly press the On/Off key to switch on the SteelTouch II. EN Fig.
V E C T RON P O S S T EELT OUC H II 7.1 . 2 . Swi tch i n g of f th e Ste e lTo u ch I I This chapter tells you how to switch off the SteelTouch II. • Shortly press the On/Off key to switch off the SteelTouch II. Fig.
7. 2 . Ente r i n g d a t a to th e Ste e lTo u ch I I This chapter tells you how to enter data to the SteelTouch II via touch screen. You are also informed about the display elements. Your display layout may differ from the one shown in this manual, depending on programming and configuration of your SteelTouch II. Prerequisite for entering data to the SteelTouch II POS system is that SteelTouch II was started as described in chapter “6. Starting” on page 41.
V E C T RON P O S S T EELT OUC H II 8 1 2 7 3 6 5 4 Fig. 13: Data input Pos. Designation 1 Status display 2 PLU selection 3 Department selection 4 Button 5 Numeric pad 6 Info field 7 Input field 8 Receipt-, invoice- and guest check display Status display pos. 1 Displays for example the date, time and the currently logged in operator.
PLU selection pos. 2 Here you select the PLUs that are stored in PLU programming of the SteelTouch II and are shown on the graphical user interface. Department selection pos. 3 Here you select departments like for example food and drinks. Button pos. 4 On the graphical user interface there may be additional buttons like for example , for generating an invoice. Numeric pad pos. 5 Via the numeric pad you enter for instance the amount that you got from a customer. EN Info field Pos.
V E C T RON P O S S T EELT OUC H II 7. 3 . Si g n i n to Ste e lTo u ch I I This chapter tells you how to sign in to SteelTouch II. i Buttons that are mentioned in this chapter and that can be displayed as graphical elements, are shown in chapter “13. Icons” on page 76. Depending on the programming of your SteelTouch II you have to sign in to the POS system. Only then you can enter PLUs for example. The Vectron POS software stores the entries and assigns them to the respective operator.
7. 3 .1 . Si g n i n v ia o p e ra to r b u t to n Carry out the following steps if your SteelTouch II was programmed for sign in via operator button. • Enter the operator number to the numeric pad. • Press the button. i The profile of the selected operator can be protected with a secret code. For sign in you have to enter the secret code. • Enter the secret code if it is requested. • For confirmation press the button or to sign in this operator. EN 7. 3 . 2 .
V E C T RON P O S S T EELT OUC H II For SteelTouch II you can order three operator lock systems, one of which is mounted to your SteelTouch II. Standard is the Dallas iButton. Figure Key Lock Dallas iButton Standard Dallas iButton with magnet Addimat Each operator has assigned rights in the POS system. This means that you are for example allowed to void PLUs and to open the guest checks of other operators. The rights are stored in tables. These tables will be called rights tables in the following.
Carry out the following step if your SteelTouch II was programmed for sign in via operator key. • Approach the key to the operator lock. EN Fig. 14: Approaching the key to the operator lock i The profile of the selected operator can be protected with a secret code. For sign in you have to enter the secret code. • Enter the secret code if it is requested. • For confirmation press the button or to sign in this operator.
V E C T RON P O S S T EELT OUC H II 7. 4 . Si g n o u t fro m th e Ste e lTo u ch I I This chapter tells you how to sign out from the SteelTouch II. i i Buttons that are mentioned in this chapter and that can be displayed as graphical elements, are shown in chapter “13. Icons” on page 76. You should sign out from the SteelTouch II if you do not use the POS system in order to avoid entries being made by others. 7. 4 .1 .
7. 4 . 2 . Si g n o u t v ia o p e ra to r key Carry out the following step if your SteelTouch II was programmed for sign out via operator key. EN Fig. 15: Removing the key from the operator lock • Remove the key from the operator lock.
V E C T RON P O S S T EELT OUC H II 7. 5 . Wo r ki n g wi th g u es t ch e ck s This chapter informs you about the guest check (GC) function. Whether or not you can use this function depends on programming and configuration of your SteelTouch II POS system. The GC function serves for separate storage of bookings for several customers. It is useful for instance in hospitality, to store food and drinks separately for each table in a restaurant.
7. 5 . 2 . Cl osi n g a G C When you close a GC, bookings for this GC are stored. There are several ways to close a GC. • Press the button or open a new GC as described in chapter “7.5.1. Opening a GC” on page 58, to close the currently open GC. 7. 5 . 3 . F i n a l izi n g a G C With this function you generate an invoice, delete the GC bookings and close the GC. • Open the GC to be finalized as described in chapter “7.5.1. Opening a GC” on page 58.
V E C T RON P O S S T EELT OUC H II 7. 5 . 4 . S p l i t ti n g PLUs of a g u es t ch e ck to i nvo i ce The GC split function serves for generating separate invoices for one GC. This is useful if guests of one table want to pay separately. i The GC split function can only be carried out if all PLUs of a GC have been booked. Close the open GC as described in chapter “7.5.2. Closing a GC” on page 59. • Open the GC to be split as described in chapter “7.5.1. Opening a GC” on page 58.
7. 5 . 5 . S p l i t ti n g si n g l e PLUs of a g u es t ch e ck to a n oth e r g u es t ch e ck The GC split function serves for transferring single PLUs to another guest check. This is useful if some guests want to change the table. i The GC split function can only be carried out if all PLUs of a GC have been booked. Close the open GC as described in chapter “7.5.2. Closing a GC” on page 59. • Open the GC to be split as described in chapter “7.5.1. Opening a GC” on page 58. • Enter the GC no.
V E C T RON P O S S T EELT OUC H II 7. 5 . 6 . M ov i n g a l l PLUs of o n e g u es t ch e ck to a n o th e r g u es t ch e ck The move GC function serves for moving all PLUs of one GC to another. • Open the GC to be moved as described in chapter “7.5.1. Opening a GC” on page 58. • Enter the GC no. to which all PLUs are to be moved. • Press the button to move the guest check. 7. 5 .7.
7. 6 . Wo r ki n g wi th h o l d b u f fe r s This chapter informs you about the hold buffer function. Whether or not you can use this function depends on programming and configuration of your SteelTouch II. The hold buffer function serves for separate storage of bookings made by several operators. This function is useful for example in a bakery, if only one POS system is available for several users. Another scenario would be the supermarket, where a customer forgot his purse in the car.
V E C T RON P O S S T EELT OUC H II 7.7. Wo r ki n g wi th re p o r t s This chapter informs you about the report function. Whether or not you can use this function depends on programming and configuration of your SteelTouch II POS system. In reports you can evaluate data that was stored in the POS system. The Vectron POS software provides several standard reports. You can display and print PLU- and operator reports for example. A PLU report can contain e.g.
7. 8 . Vo i d a n d Co r re c ti o n This chapter informs you about the void function. Whether or not you can use this function depends on programming and configuration of your SteelTouch II. You can cancel bookings if for instance an operator made false entries. Furthermore, you can program and configure the SteelTouch II so that PLUs are cancelled and the respective invoice is corrected, if a customer returns items.
V E C T RON P O S S T EELT OUC H II 7.9. Res t a r ti n g th e Ste e lTo u ch I I Start the SteelTouch II anew by switching it off and on again. Fig. 16: Switching on the SteelTouch II • Shortly press the On/Off key to switch off the SteelTouch II. • Shortly press the On/Off key to switch on the SteelTouch II.
8. Shu t do w n This chapter tells you how to shut down the SteelTouch II. Shut down the SteelTouch II if you do not use it for a longer period. • Shortly press the On/Off key to switch off the SteelTouch II. EN Fig. 17: Switching off the SteelTouch II • Unplug the safety plug of the power cord from the socket. • Unplug all cables that are connected to the SteelTouch II except for the cables of operator lock and power cable plug.
V E C T RON P O S S T EELT OUC H II • Place the SteelTouch II on a smooth, stable and even surface with sufficient space. Fig. 18: Putting down the SteelTouch II • Unplug the female connector of the power cord from the mains plug of the power supply. • Pack up SteelTouch II and the power cord in the original packaging. • Store the SteelTouch II in a room where the temperature is between -10 and 50 °C.
9. Er r or s, po s sible r eas ons and t r ouble shoo t ing Errors Possible reasons Troubleshooting SteelTouch II cannot The power supply be switched on. plug is not put into a live socket. Put the power supply plug into a live socket. The SteelTouch II POS system does not react to your entries. The power cable plug of the power supply is not put to the power connector of SteelTouch II. Put the power cable plug of the power supply to the power connector of SteelTouch II.
V E C T RON P O S S T EELT OUC H II Errors The SteelTouch II POS system does not display anything. The SteelTouch II POS system processes other entries than those made on the touch screen. Possible reasons Programming of the SteelTouch II POS system is faulty. Contact your Vec tron dealer. The touch screen is damaged. Contact your Vec tron dealer. The SteelTouch II POS system is damaged. Contact your Vec tron dealer. Vectron POS software has a malfunction.
Errors Possible reasons Troubleshooting The operator lock of the SteelTouch II POS system does not work. The plug of the operator lock is not connected. Plug in the plug of the operator lock properly. The operator lock or the connection is damaged. Contact your Vec tron dealer.
V E C T RON P O S S T EELT OUC H II 10. S er v ic e and main t enanc e This chapter tells you how to clean the SteelTouch II and how to get technical support. A ADANGER Danger through electric shock s • • High voltage at power cord and power supply Do not clean SteelTouch II, power cord and power supply with plugged-in mains plug X X Do not open SteelTouch II and power supply You will die or suffer from burns X X Switch off SteelTouch II X X Disconnect the mains plug XX 10 .1 .
10 . 2 . Cl e a n i n g h o u si n g a n d d i s p l ay Clean the display with a fluff-free cloth. You can dampen the cloth with a mild, residue-free cleanser or water. 10 . 2 .1 . Cl e a n i n g th e co nt a c t s Clean the contacts of SteelTouch II, eg those at the ports, with a cotton bud and without applying pressure. 10 . 3 . M a i nte n a n ce Any maintenance work at the SteelTouch II must exclusively be carried out by your Vect ron dealer. 10 . 4 .
V E C T RON P O S S T EELT OUC H II 11. Dispo s al Vect ron Systems AG takes back waste electric and electronic equipment that has been used for commercial purposes and that was produced by or on behalf of the company, consistent with Art. 9 of European Union Directive 2002/96/EU, last changed by European Union Directive 2003/108/EU. The company will dispose of the waste electric and electronic equipment properly.
12. Glo s s ar y This chapter explains the terms that are used in context with the SteelTouch II. Term Definition Bar code Information, which consists of bars with varying widths and spaces of parallel lines. The bar code represents data, which eg the POS system can decode. Button A button is programmed in the POS system and releases commands. The programmed commands can be called via display or keyboard of the POS system.
V E C T RON P O S S T EELT OUC H II 13. Ic ons Icons are pictographs on the display of the SteelTouch II. Icons shown on the display are designated buttons. A touch of the display button calls functions, like e.g. generating an invoice. This chapter lists some of the icons integrated in Vectron POS software and explains their meaning. You can load self-created icons to Vectron POS software, e.g. for product groups or products.
Icon Meaning Icon Meaning Operator Void last entry Manager function only GC Open GC/Operator GC 0 GC split Side dishes Transfer GC Beer GC move Ice cream Table map Fish Enter GC-text Meat X-report Drinks Z-report Main courses Temp.
V E C T RON P O S S T EELT OUC H II Icon Meaning Hot drinks 78 Icon Meaning Wine
14. EC Declar a t ion o f c on f or mi t y Manufacturer Vectron Systems AG Willy-Brandt-Weg 41 48155 Muenster, Germany Device type Type designation Stationary POS system Vectron POS SteelTouch II The manufacturer declares that the above designated product complies with the fundamental standards of guidelines 2004/108/ EC and 2006/95/EC when used as directed.
V E C T RON P O S S T EELT OUC H II 15. D ocumen t r e v ision Date 80 Modification 20.05.2011 First creation and publication 04.07.2011 Editorial modifications 18.08.
16. Ac c e s s or ie s At this point we would like to inform you about the accessories you can purchase for the SteelTouch II. More information and the technical data for accessories are available on the Internet at www.vectron.de. Please address your questions concerning our products to your Vectron dealer. 16 .1 . O p e ra to r l o ck s 16 .1 .1 . D a l l a s i B u t to n St a n d a rd Operator lock Dallas iButton Standard in stainless steel casing. Operator keys are not held magnetically. EN Fig.
V E C T RON P O S S T EELT OUC H II 16 .1 . 2 . D a l l a s M a g n e t Operator lock Dallas Magnet in stainless steel casing. Operator keys are held magnetically. Fig. 20: Dallas Magnet 16 .1 . 3 . Ad d i m a t Operator lock Addimat in stainless steel casing. Operator keys are held magnetically. Fig.
16 . 2 . Cu s to m e r d i s p l ay The SteelTouch II can be equipped with a customer display, which is mounted to the rear of the housing. The display, which is integrated in a high-quality stainless steel housing, can show two lines with 20 alphanumeric characters each. Fig.
V E C T RON P O S S T EELT OUC H II 16 . 3 . To u ch p e n s 16 . 3 .1 . To u ch p e n The touch pen serves for entering data via the touch screen of SteelTouch II. The touch pen is made of plastics. Fig. 23: Touch pen 16 . 3 . 2 . Ve c tro n To u ch p e n The touch pen serves for entering data via the touch screen of SteelTouch II. The touch pen is made of plastics. Fig. 24: Vectron Touch pen 16 . 4 .
16 . 5 . Wa l l m o u nt The optionally available wall mount allows mounting the SteelTouch II at a wall. Fig.
V E C T RON P O S S T EELT OUC H II 16 . 6 . St a n d S 3 0 0 The S300 stand, which was particularly developed for the SteelTouch series, can be mounted to the SteelTouch II in combination with the VESA-Mount adapter plate (100 mm). It completes the exclusive design of the POS system. Fig.
17. O t her Vec t r on pr oduc t s At this point we would like to inform you about additional Vectron products. More information and the technical data for Vectron products are available on the Internet at www.vectron.de. Please address your questions concerning our products to your Vectron dealer. 17.1 . St a ti o n a r y Ve c tro n P OS sys te m s Stationary Vectron POS systems with fast and reliable Vectron hardware are perfectly suited to single station use.
V E C T RON P O S S T EELT OUC H II 17.1 .1 . Ve c tro n P OS Ste e lTo u ch P C Vectron POS SteelTouch PC combines the flexibility of a computer and the performance of Vectron POS software. It has a 38.1 cm (15") TFT-display in a stainless steel housing. Input is made via the touch screen. Fig.
17.1 . 2 . Ve c tro n P OS M o d u l a r Vectron POS Modular can be combined with various monitors and keyboards. Monitor variants: • Monitor Vectron D80T with 21.3-cm (8.4") TFT-display • Monitor Vectron D151T with 38.1-cm (15") TFT-display • Monitor Vectron D153T with 38.1-cm (15") TFT-display • Monitor Vectron D171T with 43.2-cm (17") TFT-display Keyboard variants: • Raised keyboard Vectron K10R • Flat keyboard Vectron K10F EN Fig.
V E C T RON P O S S T EELT OUC H II 17.1 . 3 . Ve c tro n P OS Co l o rTo u ch Vectron POS ColorTouch has a 30.7 cm (12.1") TFT-display. Input is made via the touch screen. Fig.
17.1 . 4 . Ve c tro n P OS Va r i o Vectron POS Vario has a 26.4 cm (10.4") TFT-display. Input is either made via the optional touch screen or via raised or flat keyboard. EN Fig.
V E C T RON P O S S T EELT OUC H II 17.1 . 5 . Ve c tro n P OS M i n i Vectron POS Mini has a 14.5 cm (5.7") display. Input is either made via the optional touch screen or via flat keyboard. Fig.
17. 2 . M o b i l e / hy b r i d Ve c tro n P OS sys te m s Mobile and hybrid Vectron POS systems with fast and reliable Vectron hardware are perfectly suited to variable and location-independent use. All stationary and mobile Vectron POS systems are compatible. 17. 2 .1 . Ve c tro n P OS M o b i l e P ro Vectron POS MobilePro has an 8.9 cm (3.5") display. Input is either made via the optional touch screen or via keyboard. EN Fig.
V E C T RON P O S S T EELT OUC H II 17. 2 . 2 . Ve c tro n P OS M o b i l eTo u ch Vectron POS MobileTouch has a 10.9 cm (4.3") display. Input is made via touch screen. Fig.
17. 2 . 3 . Ve c tro n P OS M o b i l eXL Vectron POS MobileXL can be used either as mobile POS system or as stationary system in the charging-/docking station. It has a 14.5 cm (5.7") display. Input is made via touch screen. EN Fig.
V E C T RON P O S S T EELT OUC H II 17. 2 . 4 . Ve c tro n P OS M o b i l e Pa d Vectron POS MobilePad can be used either as mobile POS system or as stationary system in the charging-/docking station. It has a 21.3-cm (8.4") display. Input is made via touch screen. Fig.
17. 3 . Ve c tro n s of t wa re Vectron software is the ideal completion to Vectron POS systems for extensive and demanding applications in all trades. 17. 3 .1 . Ve c tro n P OS s of t wa re All Vectron POS systems use the same software. Thanks to its high flexibility, Vectron POS software is applicable in all trades. This double platform strategy is worldwide unequalled. 17. 3 . 2 . Ve c tro n P OS P C Vectron POS PC transports the Vectron POS software to a computer.
V E C T RON P O S S T EELT OUC H II 17. 3 . 3 . Ve c tro n Co m m a n d e r Vectron Commander is a communication- and evaluation software for the computer with Microsoft ® Windows ® operating system. Via connection to the Vectron POS system the Vectron Commander can poll, evaluate and manage the POS system data. You are thus informed at any time about sales-, order- or working time data etc. Vectron Commander serves for display or printout of reports.
