Rhein Tech Laboratories, Inc. 360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com Client: VEGA Grieshaber KG Models: VEGAPULS 61 / 62 / 63 FCC ID: O6QPS60XK1 Standard: FCC 15.209 Report Number: 2009282 Appendix H: User Manual Please refer to the following pages.
Operating Instructions VEGAPULS 62 4 … 20 mA/HART two-wire Document ID: 36503 Radar
Contents Contents 1 About this document 1.1 1.2 1.3 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. .. .. .. .. .. 5 5 5 5 6 6 6 6 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. 7 8 8 9 General instructions . . . . . . . . . . . . . . . . . Mounting preparations - Horn antenna . . . . Mounting preparations - Parabolic antenna. Mounting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 8 Set up with other systems 8.1 8.2 9 DD adjustment programs . . . . . . . . . . . . . . . . . . . . . Communicator 375, 475 . . . . . . . . . . . . . . . . . . . . . . 45 45 Diagnosis and service .. .. .. .. .. .. .. 46 46 47 50 51 51 52 10.1 Dismounting steps . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 53 9.1 9.2 9.3 9.4 9.5 9.6 9.7 Maintenance . . . . . . . . . . . . . . . . .
1 About this document 1 About this document 1.1 Function This operating instructions manual provides all the information you need for mounting, connection and setup as well as important instructions for maintenance and fault rectification. Please read this information before putting the instrument into operation and keep this manual accessible in the immediate vicinity of the device. 1.2 Target group This operating instructions manual is directed to trained qualified personnel.
2 For your safety 2 For your safety 2.1 Authorised personnel All operations described in this operating instructions manual must be carried out only by trained specialist personnel authorised by the plant operator. During work on and with the device the required personal protective equipment must always be worn. 2.2 Appropriate use VEGAPULS 62 is a sensor for continuous level measurement. You can find detailed information on the application range in chapter "Product description".
2 For your safety Depending on the instrument version, the emitting frequencies are in the C or K band range. The low emitting frequencies are far below the internationally approved limit values. When used correctly, there is no danger to health. 2.5 CE conformity The device fulfills the legal requirements of the applicable EC guidelines. By attaching the CE mark, VEGA provides a confirmation of successful testing. You can find the CE conformity declaration in the download area of www.vega.com. 2.
3 Product description 3 Product description 3.1 Configuration Type label The type label contains the most important data for identification and use of the instrument: 1 2 3 4 5 6 7 8 9 12 11 10 Fig.
3 Product description l Scope of delivery Electronics with increased sensitivity type PS60HS, modification status ≥ 22 The scope of delivery encompasses: l l Radar sensor Documentation - this operating instructions manual - Safety Manual (SIL) VEGAPULS 62 (optional) - Operating instructions manual "Indicating and adjustment module" (optional) - Operating instructions "Radio module" (optional) - Supplementary instructions manual "Heating for indicating and adjustment module" (optional) - Supplementary ins
3 Product description The packaging of standard instruments consists of environmentfriendly, recyclable cardboard. For special versions, PE foam or PE foil is also used. Dispose of the packaging material via specialised recycling companies. Transport Transport must be carried out under consideration of the notes on the transport packaging. Nonobservance of these instructions can cause damage to the device.
3 Product description It is suitable for measured value indication and adjustment of plics® sensors and is connected to the sensor with an up to 50 m long, fourwire, screened standard cable. You can find further information in the operating instructions "VEGADIS 61" (Document-ID 27720). External indicating and adjustment unit with HART protocol VEGADIS 62 is suitable for measured value indication and adjustment of sensors with HART protocol. It is looped into the 4 … 20 mA/HART signal cable.
4 Mounting 4 Mounting 4.1 General instructions Screwing in With instruments with threaded process fitting, suitable tools must be applied for tightening the hexagon. Warning: The housing must not be used to screw the instrument in! Applying tightening force can damage internal parts of the housing. Moisture Use the recommended cables (see chapter "Connecting to power supply") and tighten the cable gland.
4 Mounting Note: The radar sensor with rinsing air connection or antenna extension is provided with a notch on the antenna socket. This notch must correspond to the marking on the hexagon of the process fitting (the marking specifies the position of the polarisation level of the radar signal). 1 2 3 4 Fig. 2: Dismounting of the horn antenna 1 2 3 4 Marking of the polarisation plane Notch at the antenna socket Hexagon screws on the antenna socket Antenna 4.
4 Mounting Note: A damaged O-ring seal must be replaced: FKM (Viton) article no. 2.28248, FFKM (Kalrez 6375) article no. 2.27351 8 Remount the parabolic antenna (4) 9 Fasten compression nut (1) with a wrench (width across flats 41), torque max. 50 Nm 10 Fasten counter nut (2) with a wrench (width across flats 36), torque max. 40 Nm Note: Take note for the version with rinsing air connection that the holes in the antenna and in the process fitting correspond.
4 Mounting 11 Fig. 4: Position of the polarisation level 1 Mounting position Marking hole When mounting the sensor, keep a distance of at least 200 mm (7.874 in) from the vessel wall. If the sensor is installed in the center of dished or round vessel tops, multiple echoes can arise. However, these can be suppressed by an appropriate adjustment (see chapter "Setup"). If you cannot keep this distance you should carry out a false echo storage before setup.
4 Mounting Fig. 6: Mounting of the radar sensor on vessels with conical bottom Inflowing medium Do not mount the instruments in or above the filling stream. Make sure that you detect the product surface, not the inflowing product. Fig. 7: Mounting of the radar sensor with inflowing medium The socket piece should be dimensioned in such a way that the antenna end protrudes at least 10 mm (0.4 in) out of the socket.
> 10 mm 4 Mounting Fig. 8: Recommended socket mounting h max. If the reflective properties of the medium are good, you can mount radar sensor on sockets which are higher than the length of the antenna. You will find recommended values for socket heights in the following illustration. The socket end should be smooth and burr-free, if possible also rounded. After installation you must carry out a false echo storage. d d 1½" 50 mm/2" 80 mm/3" 100 mm/4" 150 mm/6" h max.
4 Mounting Fig. 10: Alignment in liquids Vessel installations The mounting location of the radar sensor should be a place where no other equipment or fixtures cross the path of the microwave signals. Vessel installations, such as e.g. ladders, limit switches, heating spirals, struts, etc., can cause false echoes and impair the useful echo. Make sure when planning your measuring site that the radar sensor has a "clear view" to the measured product.
4 Mounting Fig. 12: Agitators Foam generation Through the action of filling, stirring and other processes in the vessel, compact foams that damp the emitted signals considerably may form on the product surface. If foams are causing measurement errors, the biggest possible radar antennas, the electronics with increased sensitivity or low frequency radar sensors (C band) should be used. As an alternative, sensors with guided microwave can be used.
4 Mounting 1 1 2 2 3 3 4 100% 5 6 7 8 9 0% Fig.
4 Mounting l The measurement through a ball valve with complete run is possible Constructional requirements on the surge pipe: l l l l l l l l l l l Measurement in the bypass Material metal, smoother inner tube Preferably pultruded or straight beaded stainless steel tube Welded joint should be straight and lie in one axis with the holes Flanges are welded to the tube according to the orientation of the polarisation level In case of a extension with a welding neck flange or pipe collar as well as when a
4 Mounting 1 2 3 4 100 % 6 5 0% Fig.
4 Mounting l l l l l l Mounting in the vessel insulation Material metal, smoother inner tube In case of an extremely rough tube inner surface, use an inserted tube (tube in tube) or a radar sensor with tube antenna Flanges are welded to the tube according to the orientation of the polarisation level Gap size with junctions ≤ 0.
4 Mounting 1 90° ≥ 50 mm 2 2 33 90° ≥ 2 mm x hmax hmax dmin 3 ... 4 hmax 4 Fig. 16: Flow measurement with rectangular flume: dmin. = min. distance of the sensor (see chapter "Technical data"); hmax. = max.
4 Mounting Flow measurement with Khafagi Venturi flume 3 ... 4 x hmax d 90° hmax 1 B 2 Fig. 17: Flow measurement with Khafagi-Venturi flume: d = Min. distance to sensor; hmax. = max. filling of the flume; B = tightest constriction in the flume 1 2 Position sensor Venturi flume In general, the following points must be observed: l l l l Installation of the sensor at the inlet side Installation in the centre of the flume and vertical to the liquid surface Distance to the Venturi flume Min.
5 Connecting to power supply 5 Connecting to power supply 5.1 Preparing the connection Safety instructions Always keep in mind the following safety instructions: l l Voltage supply Connect only in the complete absence of line voltage If overvoltages are expected, install overvoltage arresters Power supply and current signal are carried on the same two-wire cable. The voltage supply range can differ depending on the instrument version. The data for power supply are specified in chapter "Technical data".
5 Connecting to power supply Cable screening and grounding If screened cable is necessary, connect the cable screen on both ends to ground potential. In the sensor, the screen must be connected directly to the internal ground terminal. The ground terminal on the outside of the housing must be connected to the potential equalisation (low impedance). If potential equalisation currents are expected, the connection on the processing side must be made via a ceramic capacitor (e. g. 1 nF, 1500 V).
5 Connecting to power supply 5 Insert the cable into the sensor through the cable entry Fig. 18: Connection steps 5 and 6 6 Insert the wire ends into the terminals according to the wiring plan Information: Solid cores as well as flexible cores with cable end sleeves are inserted directly into the terminal openings. In case of flexible cores without end sleeves, press the terminal head with a small screwdriver; the terminal opening is freed. When the screwdriver is released, the terminal closes again.
5 Connecting to power supply 5.3 Wiring plan, single chamber housing The following illustration applies to the non-Ex as well as to the Ex-ia version. Electronics and connection compartment 2 3 4...20mA (+)1 2(-) 5 6 7 8 4 1 Fig. 19: Electronics and connection compartment with single chamber housing 1 2 3 4 Voltage supply/Signal output For indicating and adjustment module or interface adapter For external indicating and adjustment unit Ground terminal for connection of the cable screen 5.
5 Connecting to power supply Information: The connection of an external indicating and adjustment unit is not possible with this double chamber housing. Connection compartment 2 4...20mA (+)1 2(-) 3 1 Fig. 21: Connection compartment, double chamber housing 1 2 3 Voltage supply/Signal output For indicating and adjustment module or interface adapter Ground terminal for connection of the cable screen 5.5 Wiring plan with double chamber housing Ex d Electronics compartment 2 4...
5 Connecting to power supply Connection compartment 4...20mA (+)1 2(-) 2 1 Fig. 23: Connection compartment double chamber housing Ex d 1 2 Voltage supply/Signal output Ground terminal for connection of the cable screen 5.6 Wiring plan - version IP 66/IP 68, 1 bar Wire assignment connection cable + 1 2 Fig. 24: Wire assignment fix connected connection cable 1 2 brown (+) and blue (-) to power supply or to the processing system Shielding 5.
6 Set up with the indicating and adjustment module 6 Set up with the indicating and adjustment module 6.1 Insert indicating and adjustment module Mount/Dismount indicating and adjustment module The indicating and adjustment module can be inserted into the sensor and removed again at any time. It is not necessary to interrupt the power supply.
6 Set up with the indicating and adjustment module 6.2 Adjustment system 1 2 Fig.
6 Set up with the indicating and adjustment module 6.3 Parameter adjustment With the parameter adjustment, the instrument is adapted to the application conditions. The parameter adjustment is carried out via an adjustment menu. Information: In this operating instructions manual, the instrument-specific parameters are described. Further general parameters are described in the operating instructions manual "Indicating and adjustment module".
6 Set up with the indicating and adjustment module Through this selection, the sensor is adapted perfectly to the product and measurement reliability, particularly in products with poor reflective properties, is considerably increased. Enter the requested parameters via the appropriate keys, save your settings with [OK] and jump to the next menu item with the [ESC] and the [->] key. Setup/Application In addition to the medium, also the application or the application place can influence the measurement.
6 Set up with the indicating and adjustment module The selection "Standpipe" opens a new window in which the inner diameter of the applied standpipe is entered. The following options are available when "Bulk solid" is selected: Through this selection, the sensor is adapted optimally to the application or the location and measurement reliability under the various basic conditions is increased considerably.
6 Set up with the indicating and adjustment module Enter the requested parameters via the appropriate keys, save your settings with [OK] and jump to the next menu item with the [ESC] and the [->] key. Setup/Adjustment As a radar sensor is a distance measuring instrument, the distance from the sensor to the product surface is measured. To have the real product level displayed, an allocation of the measured distance to the percentage height must be made.
6 Set up with the indicating and adjustment module Setup/Max. adjustment Proceed as follows: 1 Select with [->] the menu item max. adjustment and confirm with [OK]. 2 Prepare the percentage value for editing with [OK] and set the cursor to the requested position with [->]. 3 Set the requested percentage value with [+] and save with [OK]. The cursor jumps now to the distance value. 4 Enter the appropriate distance value in m (corresponding to the percentage value) for the full vessel.
6 Set up with the indicating and adjustment module 2 Confirm again with [OK]. 3 Confirm again with [OK] and select with [->] "Create new". 4 Confirm again with [OK] and enter the actual distance from the sensor to the product surface. 5 All interfering signals in this section are detected by the sensor and stored after confirming with [OK]. Note: Check the distance to the product surface, because if an incorrect (too large) value is entered, the existing level will be saved as false signal.
6 Set up with the indicating and adjustment module Enter the requested parameters via the appropriate keys, save your settings and jump to the next menu item with the [ESC] and [->] key. Caution: If the instrument is used as part of an overfill protection system according to WHG (Water Resources Act), please note the following: If a linearisation curve is selected, the measuring signal is no longer compulsorily linear proportional to the level.
6 Set up with the indicating and adjustment module Setup: Resetting of the parameter settings to the default values of the respective instrument in the menu item Setup. Order-related settings remain but are not taken over into the current parameters. Usergenerated false signal suppression, user-programmed linearization curve, measured value memory as well as event memory remain untouched. The linearization is set to linear. False signal suppression: Deleting a previously created false signal suppression.
6 Set up with the indicating and adjustment module Menu Further settings Menu item Default value Scaling 0.00 lin %, 0 l 100.00 lin %, 100 l Lighting Switched off Distance unit m Temperature unit °C Probe length Length of the standpipe Ex factory Linearisation curve linear HART mode Standard Address 0 6.4 Saving the parameter adjustment data It is recommended noting the adjusted data, e.g. in this operating instructions manual and archive them afterwards.
7 Setup with PACTware 7 Setup with PACTware 7.1 Connecting the PC Via the interface adapter directly on the sensor 2 1 3 Fig. 27: Connection of the PC directly to the sensor via the interface adapter 1 2 3 USB cable to the PC Interface adapter VEGACONNECT 4 Sensor Information: The interface adapter VEGACONNECT 3 or additional previous versions are not suitable for connection to the sensor.
7 Setup with PACTware Via the interface adapter and HART 2 4 N OPE 3 USB TWIST LO CK 1 Fig. 28: Connecting the PC via HART to the signal cable 1 2 3 4 5 Sensor HART resistance 250 Ω (optional depending on processing) Connection cable with 2 mm pins and terminals Processing system/PLC/Voltage supply Interface adapter, for example VEGACONNECT 4 Note: With power supply units with integrated HART resistance (internal resistance approx. 250 Ω), an additional external resistance is not necessary.
7 Setup with PACTware Fig. 29: Example of a DTM view Standard/Full version All device DTMs are available as a free-of-charge standard version and as a full version that must be purchased. In the standard version, all functions for complete setup are already included. An assistent for simple project configuration simplifies the adjustment considerably. Saving/printing the project as well as import/export functions are also part of the standard version.
8 Set up with other systems 8 Set up with other systems 8.1 DD adjustment programs Device descriptions as Enhanced Device Description (EDD) are available for DD adjustment programs such as for example AMS™ and PDM. A free-of-charge download of these files is available via Internet. Move via www.vega.com and "Downloads" to "Software". 8.2 Communicator 375, 475 Device descriptions for the instrument are available as DD or EDD for parameter adjustment with the Field Communicator 375 or 475.
9 Diagnosis and service 9 Diagnosis and service 9.1 Maintenance When the device is used correctly, no maintenance is required in normal operation. 9.2 Measured value and event memory Measured value memory The instrument has an integrated measured value memory with time stamp. Up to 100,000 measured values can be saved in the sensor in a ringing memory. Each entry contains date/time as well as the respective measured value.
9 Diagnosis and service 9.3 Status messages The instrument has a self-monitoring and diagnosis according to NE 107 and VDI/VDE 2650. The following status messages can be outputted: Failure: Due to a malfunction in the instrument, a failure message is outpuuted. This status message is activated in the delivery status and cannot be deactivated by the user. Function check: The instrument is in operation, the measured value is temporarily invalid (for example during simulation).
9 Diagnosis and service Code Text message Cause Removal F025 Error in the linearization table l Index markers are not continuously rising, for examle unlogical value pairs l Check linearization table l Delete table/Create new F036 No operable software l Failed or interrupted software update l l l l F040 Error in the electronics l Hardware defect l Exchange the electronics l Send instrument for repair F080 l General software error l Separate operating voltage briefly F105 Determine measured va
9 Diagnosis and service Function check Out of specification The following table shows the codes and text messages of the status message "Function check" and provides information on causes as well as corrective measures. Code Text message Cause Removal C700 Simulation l Simulation active l Finish simulation l Wait for the automatic end after 60 mins. The following table shows the codes and text messages of the status message "Out of specification" and gives instructions for the reason and removal.
9 Diagnosis and service Code Text message Cause Removal M503 Reliability too low l The echot/noise ratio is the l Check installation and prosmall for a reliable measucess conditions rement l Clean the antenna l Change polarisation direction l Use instrument with higher sensitivity M504 Error on an device interface l Hardware defect l Check connections l Exchange the electronics l Send instrument for repair 9.
9 Diagnosis and service Error Cause Oscillator in the Current signal greater than 22 mA sensor defective or less than 3.6 mA Removal Exchange the instrument or send it in for repair Reaction after fault rectification Depending on the failure reason and measures taken, the steps described in chapter "Set up" must be carried out again, if necessary. 24 hour service hotline However, should these measures not be successful, call the VEGA service hotline in urgent cases under the phone no.
9 Diagnosis and service l Current sensor software as file Caution: Keep in mind that a software update can lead to expiry of the approvals. You can find detailed information on our homepage www. vega.com. Load sensor software to PC At "www.vega.com/downloads" go to "Software". Select under "plics sensors and instruments" the respective instrument series and software version. Load the zip file via the right mouse key with "Save target as" e.g. on the desktop of your PC.
10 Dismounting 10 Dismounting 10.1 Dismounting steps Warning: Before dismounting, be aware of dangerous process conditions such as e.g. pressure in the vessel, high temperatures, corrosive or toxic products etc. Take note of chapters "Mounting" and "Connecting to power supply" and carry out the listed steps in reverse order. 10.2 Disposal The instrument consists of materials which can be recycled by specialised recycling companies.
11 Supplement 11 Supplement 11.1 Technical data General data 316L corresponds to 1.4404 or 1.4435 Materials, wetted parts - Process fitting 316L, Hastelloy C22, Monell Alloy - Process seal On site (instruments with thread: Klingersil C-4400 is attached) - Antenna 316L, Hastelloy C22, Tantalum, 316L electropolished, stainless steel investment casting 1.4848, Monell Alloy, 316L Safecoat coated - Antenna impedance cone PTFE (TFM 1600 PTFE), PP, PEEK, ceramic (99.
11 Supplement Input variable Measured variable The measured quantity is the distance between process fitting of the sensor and product surface. The reference plane is the seal surface on the hexagon or the lower side of the flange. 1 3 4 2 Fig. 30: Data of the input variable 1 2 3 4 Reference plane Measured variable, max. measuring range Antenna length Useful measuring range Standard electronics Max. measuring range Recommended measuring range - Antenna ø 40 mm (1.575 in) 35 m (114.
11 Supplement Cycle time measuring cycle approx. - Standard electronics - Electronics with increased sensitivity 0.5 s 1s Signal resolution 0.3 µA Residual ripple ±0.4 µA Failure signal current output (adjustable) mA-value unchanged 20.5 mA, 22 mA, < 3.6 mA Max. output current 22 mA Starting current ≤ 3.6 mA; ≤ 10 mA for 5 ms after switching on Load see load diagram under Power supply Damping (63 % of the input variable) 0 … 999 s, adjustable HART output values according to HART 7.
11 Supplement 10 mm (0.394 in) 2 mm (0.079 in) 0 - 2 mm (- 0.079 in) 0,5 m (1.6 ft) - 10 mm (- 0.394 in) 1 2 3 Fig. 31: Deviation under reference conditions 1 2 3 Reference plane Antenna edge Recommended measuring range Reproducibility ≤ ±1 mm Deviation with bulk solids The values are considerably application-dependent. Firm specifications are hence not possible. Variables influencing measurement accuracy Temperature drift ±0.03 %/10 K relating to the 16 mA span max. ±0.
11 Supplement Gas phase Temperature 1 bar/ 14.5 psig 10 bar/ 145 psig 50 bar/ 725 psig 100 bar/ 1450 psig 200 bar/ 2900 psig 0.00 % 0.22 % 1.2 % 2.4 % 4.9 % 200 °C/392 °F -0.01 % 0.13 % 0.74 % 1.5 % 3.0 % 400 °C/752 °F -0.02 % 0.08 % 0.52 % 1.1 % 2.1 % 20 °C/68 °F -0.01 % 0.10 % 0.61 % 1.2 % 2.5 % 200 °C/392 °F -0.02 % 0.05 % 0.37 % 0.76 % 1.6 % 400 °C/752 °F -0.02 % 0.03 % 0.25 % 0.53 % 1.
11 Supplement Ambient conditions Ambient, storage and transport temperature -40 … +80 °C (-40 … +176 °F) Process conditions For the process conditions, you also have to note the specifications on the type label. Always the lowest value is applicable.
11 Supplement Data on rinsing air connection Pressure max. 6 bar (87.02 psig) Air quantity without reflux valve - 0.2 bar (2.9 psig) 2.0 m3/h - 0.5 bar (7.25 psig) 3.5 m3/h - 1 bar (14.5 psig) 4.5 m3/h - 1.5 bar (21.76 psig) 5 m3/h - 2 bar (29.0 psig) 5.
11 Supplement l 1 x closing cap ½ NPT, 1 x blind stopper ½ NPT, 1 x blind stopper M16 x 1.5 or optionally7)1 x plug M12 x 1 for external indicating and adjustment unit or: l Spring-loaded terminals for wire cross-section - Massive wire, cord - 1 x plug (depending on the version), 1 x blind stopper M20 x 1.5; 1 x blind stopper M16 x 1.5 or optionally8)1 x plug M12 x 1 for external indicating and adjustment unit 0.2 … 2.5 mm² (AWG 24 … 14) 0.2 … 1.
11 Supplement - Housing ABS - Inspection window Polyester foil Integrated clock Date format Day.Month.Year Time format 12 h/24 h Time zone Ex factory CET Electronics temperature measurement Resolution 1 °C (1.8 °F) Accuracy ±1 °C (1.8 °F) Voltage supply Operating voltage - Non-Ex instrument 9.6 … 36 V DC - Ex-ia instrument 9.
11 Supplement Ω 1200 927 750 3 500 2 1 250 4 9,6 12 14 15,1 16 18 20 22 24 26 28 30 32 34 36 V Fig. 32: Voltage diagram 1 2 3 4 HART load Voltage limit Ex-ia instrument Voltage limit non-Ex/Ex-d instrument Operating voltage Electrical protective measures Protection, depending on housing version - Plastic housing IP 66/IP 67 - Aluminium housing, stainless steel housing - investment casting, stainless steel housing - electro-polished IP 66/IP 68 (0.
11 Supplement 11.2 Dimensions The following dimensional drawings represent only an extract of the possible versions. Detailed dimensional drawings can be downloaded on www.vega.com under "Downloads" and "Drawings". Housing plastic ~ 69 mm (2.72") ø 79 mm (3.03") ~ 84 mm (3.31") ø 79 mm (3.31") 112 mm (4.41") 112 mm (4.41") M16x1,5 M20x1,5/ ½ NPT M20x1,5/ ½ NPT 1 1 2 2 Single chamber version Double chamber version Aluminium housing ~ 87 mm (3.43") ~ 116 mm (4.57") ø 86 mm (3.39") ø 86 mm (3.
11 Supplement Aluminium housing in protection rating IP 66/IP 68 (1 bar) ~ 105 mm (4.13") ~ 150 mm (5.91") ø 84 mm (3.31") ø 84 mm (3.31") M20x1,5 120 mm (4.72") 116 mm (4.57") M16x1,5 M20x1,5 M20x1,5/ ½ NPT 1 1 2 2 Single chamber version Double chamber version Stainless steel housing ~ 69 mm (2.72") ø 79 mm (3.11") ~ 59 mm (2.32") ø 80 mm (3.15") ~ 87 mm (3.43") ø 86 mm (3.
11 Supplement Stainless steel housing in protection rating IP 66/IP 68, 1 bar ~ 93 mm (3.66") ~ 103 mm (4.06") ~ 105 mm (4.13") ø 84 mm (3.31") ø 80 mm (3.15") ø 77 mm (3.03") 120 mm (4.72") 112 mm (4.41") M20x1,5 M20x1,5/ ½ NPT 1 1 2 2 117 mm (4.
11 Supplement 144 mm (5.67") 2 y G1½A / 1½ NPT mm y x 1½" 100 ø40 2" 120 ø48 3" 216 ø75 4" 430 ø95 22 mm (0.87") 38 mm (1.50") 1 SW 46 mm (1.81") 22 mm (0.87") VEGAPULS 62 - horn antenna in threaded version x y 1½" 3.94" 4.72" 8.50" 16.93" 2" 3" 4" x ø1.58" ø1.89" ø2.95" ø3.74" y inch x Fig.
11 Supplement VEGAPULS 62 - horn antenna in flange version 2 165 mm (6.5") 260 mm (10.24") y 60 mm (2.36") 1 x mm y x inch y 1½" 100 ø40 1½" 2" 120 ø48 2" 3" 216 ø75 3" 4" 430 ø95 4" 3.94" 4.72" 8.50" 16.93" x ø1.58" ø1.89" ø2.95" ø3.74" Fig.
11 Supplement VEGAPULS 62 - horn antenna and swivelling holder max. 15 ° (0.59") 1 x 146 m mm y x 1½" 100 ø 40 2" 120 ø 48 3" 216 ø 75 4" 430 ø 95 inch y x 1½" 2" 3" 3.94" 4.72" 8.50" 16.93" ø 1.58" ø 1.89" ø 2.95" ø 3.74" y 4" 20 m m (0.79 ") y 20 m m (0.79 ") m (5.7 5") 40 m m (1.58 ") 2 x Fig.
11 Supplement VEGAPULS 62 - parabolic antenna and swivelling holder max. 15 ° (0.59") 1 130 m m (5.1 2") 120 m m (4.7 2") 40 m m (1.58 ") 2 ø 243 mm (9 .57") Fig.
11 Supplement 11.3 Industrial property rights VEGA product lines are global protected by industrial property rights. Further information see http://www.vega.com. Only in U.S.A.: Further information see patent label at the sensor housing. VEGA Produktfamilien sind weltweit geschützt durch gewerbliche Schutzrechte. Nähere Informationen unter http://www.vega.com. Les lignes de produits VEGA sont globalement protégées par des droits de propriété intellectuelle.
Index INDEX A Accessory - External indicating and adjustment unit 910 - External radio unit 10 - Indicating and adjustment module 9 - Interface adapter 9 - Protective cover 10 Adjustment 36 - Max. adjustment 37 - Min.
Index - Electronics module 10 Reset 39 S Serial number 7 Service hotline 51 Shielding 26 Socket mounting 15 Status messages 47 T Type label 7 V 36503-EN-100607 Vessel form 35 Vessel height 35 Vessel installations 17 Vessel insulation 22 Voltage supply 25 VEGAPULS 62 • 4 … 20 mA/HART two-wire 73
Index 36503-EN-100607 74 VEGAPULS 62 • 4 … 20 mA/HART two-wire
36503-EN-100607 Index VEGAPULS 62 • 4 … 20 mA/HART two-wire 75
Printing date: VEGA Grieshaber KG Am Hohenstein 113 77761 Schiltach Germany Phone +49 7836 50-0 Fax +49 7836 50-201 E-mail: info@de.vega.com www.vega.com ISO 9001 All statements concerning scope of delivery, application, practical use and operating conditions of the sensors and processing systems correspond to the information available at the time of printing.
