Operating Instructions VEGAPULS 42, 44 and 45 4 … 20 mA; HART® compact sensor
Contents Contents Safety information ........................................................................ 3 Note Ex area ................................................................................ 3 1 Product description .................................................................. 4 1.1 Function ................................................................................. 4 1.2 Application features ............................................................. 6 1.3 Adjustment ..........
Contents 7 Technical data .......................................................................... 53 7.1 Technical data ..................................................................... 53 7.2 Approvals ........................................................................... 58 7.3 Dimensions ......................................................................... 59 Supplement ..................................................................................... 62 Safety Manual ...............
Product description 1 Product description VEGAPULS series 40 sensors are a newly developed generation of extremely compact, small radar sensors for accurate, high-resolution measurement. They are characterised by very good focussing properties for applications in narrow spaces. With very modest space requirements, they were developed for measuring distances of 0 … 4 m/10 m/ 20 m and are the right choice for standard applications such as storage vessels, reservoirs and buffer tanks as well as process tanks.
Product description VEGAPULS can achieve this through a special time transformation procedure which spreads out the more than 3.6 million echo images per second in a slow-motion picture, then freezes and processes them. % 50 40 % 40 30 25 % 20 10 5% 5 0 2 0 t t Time transformation Hence, it is possible for the radar sensors to process the slow-motion pictures of the sensor environment precisely and in detail in cycles of 0.5 to 1 second without using timeconsuming frequency analysis (e.g.
Product description 1.2 Application features 1.3 Adjustment Applications • level measurement of any liquid • measurement also in vacuum • all slightly conductive materials and all substances with a dielectric constant > 2.0 can be measured • measuring range 0 … 10 m (type 42). measuring range 0 … 20 m (type 44). measuring range 0 … 4 m (type 45). Every measurement set-up is unique. For that reason, every radar sensor needs some basic information on the application and the environment, e.g.
Product description The PC can be connected at any measuring site in the system or directly to the signal cable. It is connected by means of the twowire PC interface converter VEGACONNECT 3 to the sensor or the signal cable. The adjustment and parameter data can be saved with the adjustment software on the PC and can be protected by passwords. On request, the adjustments can be quickly transferred to other sensors. Adjustment with the adjustment module MINICOM With the small (3.2 cm x 6.
Product description, types and versions Adjustment with the HART® handheld 2 Types and versions Series 40 sensors with 4 … 20 mA output signal can also be adjusted with the HART ® handheld. A special DDD (Data Device Description) is not necessary - the sensors can be adjusted with the HART® standard menus of the handheld. 2.1 Survey HART Communicator VEGAPULS 42 sensors are distinguished by a G 1½ A or 1½“ NPT threaded mounting boss as process connection.
Types and versions Survey General features • Application preferably for liquids in storage tanks and process vessels with increased accuracy requirement. • Measuring range 0 … 4 m, 0 … 10 m or 0 … 20 m. • Ex approved in Zone 1 (IEC) or Zone 1 (ATEX) classification mark EEx ia [ia] IIC T6. • Integrated measured value display.
Types and versions 2.2 Antennas The antenna is the eye of the radar sensor. The shape of the antenna, however, doesn’t give a casual observer the slightest clue on how carefully the antenna geometry must be adapted to the physical properties of electromagnetic waves. The geometrical form determines focal properties and sensitivity - the same way it determines the sensitivity of a unidirectional microphone.
Types and versions Pipe antennas Pipe antennas consisting of horn antenna and standpipe or bypass tube Only in conjunction with a measuring tube, i.e. with a surge or bypass tube (which can also be curved), do horn antennas form a complete antenna system. The measuring tube acts as a conductor for the radar signals. The running time of the radar signals changes in the tube and depends on the tube diameter.
Mounting and installation 3 Mounting and installation 3.1 General installation instructions Measuring range The reference plane for the measuring range of the sensor is the lower edge of the flange or the seal shoulder of the thread. For measurements in surge or bypass tubes with VEGAPULS 45 the max. distance depends on the tube length.
Mounting and installation Emission cone and false echoes The radar signals are focused by the antenna system. The signals leave the antenna in a conical path similar to the beam pattern of a spotlight. This emission cone depends on the antenna used. Any object in this beam cone will reflect the radar signals. Within the first few meters of the beam cone, tubes, struts or other installations can interfere with the measurement.
Mounting and installation 3.2 Measurement of liquids Flange antennas Horn antenna on DIN socket piece Radar sensors are usually mounted on short DIN socket pieces. The lower side of the instrument flange is the reference plane for the measuring range. The antenna must always protrude out of the flange pipe. If the DIN socket piece is longer, please make sure that the horn antenna still protrudes out of the socket.
Mounting and installation Screwed antenna The screwed antenna is used mainly on very small vessels. The antenna fits into even the smallest vessel connection openings (11 /2 “ socket). The socket must not be longer than 135 mm (when used with a longer antenna, not longer than 250 mm). Reference plane ≤ 135 mm Screwed antenna on 1½“ mounting boss 3.3 Measurement in standpipe (surge or bypass tube) General instructions Measurement in a standpipe is preferred in vessels which contain many installations, e.
Mounting and installation Make sure the required upper vent hole in the surge pipe is aligned with the sensor type label. As an alternative to a surge pipe in the vessel, a pipe antenna system outside the vessel in a bypass tube is also possible. The surge and bypass tubes must generally be made of metal. For plastic tubes, a closed, conductive jacket is always required. When using a metal tube with plastic inner coating, make sure that the thickness of the coating is minimal (approx. 2 … 4 mm).
Mounting and installation If enough liquid (300 … 800 mm) remains in the blind lower end of the tube, the portion of the signal that penetrates the liquid and reflects from the tube bottom is sufficiently damped - the sensor can then easily distinguish it from the echo of the liquid surface. In cases where there is not enough liquid at the bottom of the tube, a deflector situated there will carry out the same function. It deflects signals that reach the tube bottom into the standard connection opening.
Mounting and installation Seals on tube connections and tube extensions Guide tube Microwaves are very sensitive to gaps in flange connections. If connections are made without proper care, distinct false echoes as well as increased signal noise can result. Observe the following points: • The applied seal should correspond to the tube inner diameter. • If possible, conductive seals such as conductive PTFE or graphite should be used. • There should be as few seal positions as possible in the guide tube.
Mounting and installation VEGAPULS 45 with integrated measuring tube VEGAPULS 45 sensor version was especially developed for measuring tube applications and is supplied complete with a 27 mm measuring tube. With a measuring tube length up to 4 m, this sensor version can be used, e.g. in existing standpipes.
Mounting and installation If you want to measure inhomogeneous or stratified products in a surge pipe, it must have holes, elongated holes or slots. These openings ensure that the liquid is mixed and corresponds to the liquid in the vessel. Surge pipe with ball valve If a ball valve is mounted in the surge pipe, maintenance and servicing can be carried out without opening the vessel (e.g. if it contains liquid gas or toxic products).
Mounting and installation Guidelines for standpipe construction VEGAPULS 44 Radar sensors for measurement on surge or bypass tubes are used with G 1½ A screwon antenna or in the flange sizes DN 50, DN 80, DN 100 and DN 150. The radar sensors with a DN 50 flange only form a functioning measuring system in conjunction with a measuring tube. Avoid welding through the pipe wall. The pipe must remain smooth inside.
Mounting and installation In products with lower dielectric values (< 4), a part of the radar signal penetrates the medium. If the vessel is nearly empty, echoes are generated by both the product and the vessel bottom. The echo from the vessel bottom can in some cases be stronger than the echo from the product surface. If a deflector is installed below the open end of the measuring tube, the radar signals are scattered and prevented from reaching the vessel bottom.
Mounting and installation Vessel installations Inflowing material Vessel installations, such as e.g. ladders, often cause false echoes. Make sure when planning your measuring location that the radar signals have free access to the measured product. Do not mount the instrument in or above the filling stream. Ensure that you detect the product surface and not the inflowing material.
Mounting and installation Strong product movements 3.5 Common installation mistakes Strong turbulence in the vessel, e.g. caused by powerful stirrers or strong chemical reactions, can seriously interfere with the measurement. A surge or bypass tube (see illustration) of sufficient size always enables reliable and problem-free measurement even if strong turbulence occurs in the vessel, provided there is no product buildup in the tube.
Mounting and installation Parabolic effects on dished or arched vessel tops Round or parabolic tank tops act on the radar signals like a parabolic mirror. If the radar sensor is placed at the focal point of such a parabolic tank top, the sensor receives amplified false echoes. The optimum mounting location is generally in the range of half the vessel radius from the centre. Wrong orientation to the product Weak measuring signals are generated if the sensor is not directly pointed at the product surface.
Mounting and installation Foam generation Standpipe installation mistakes Conductive foam is penetrated to different depths by the radar signals and generates a number of individual (bubble) echoes. At the same time, the signals are damped in foam, similar to the way heat radiation is damped by Styrofoam. Thick, dense, creamy and conductive foam can cause incorrect measurements.
Electrical connection 4 Electrical connection 4.1 Connection and connection cable Safety information As a rule, do all connecting work in the complete absence of line voltage. Always switch off the power supply before you carry out connecting work on the radar sensors. Protect yourself and the instruments, especially when using sensors which do not operate with low voltage.
Electrical connection Earthing the screen only on one end is not always effective, see the following table. The table gives a simple overview of the effectiveness of the different protective measures against electromagnetic pollution. In practice, earthing of both sides is often useful. This allows the option of earthing only one end later by simply disconnecting the other earth contact points of the screen. Why? Actual interference only appears in the operating environment.
Electrical connection Ex protection If an instrument is used in hazardous areas, the respective regulations, conformity certificates and type approvals for systems in Ex areas must be noted (e.g. DIN 0165). Intrinsically safe circuits with more than one active instrument (instrument delivering electrical energy) are not allowed. Special installation regulations (DIN 0165) must be noted. Note! Due to the possibility of potential transfer, earthing on both ends is prohibited in Ex applications.
Electrical connection Version with plastic housing Power supply Power supply 4 … 20 mA (passive) 1) + + - 4 … 20 mA (active) 2) - + - To the indicating instrument in the sensor lid or to the external indicating instrument VEGADIS 50 To the display in the lid or the external indicating instrument Cable entry M20 x 1.5 +3 1 2 24-20mA 5 Communication 6 Display 7 8 (+) L1 2.23272 +1 Sockets for connection of the HART ® handheld or the VEGACONNECT Tank 1 m (d) 12.
Electrical connection Version with aluminium housing Two-wire technology (loop powered) Four-wire technology 4 … 20 mA active 2) + 4 … 20 mA passive 1) To the indicating instrument in the + sensor lid or to the external indicating instrument VEGADIS 50 M20 x 1.5 (diameter of the connection cable 5…9 mm) 1 2 C 3 4 5 6 7 8 1 2 C 3 4 5 6 7 8 (+) (-) L1 N Communication - +4...
Electrical connection Version with aluminium housing and pressure-tight encapsulated terminal compartment Two-wire EEx d terminal compartment (opening in Ex atmosphere not allowed) Exd safe connection to the Exd terminal compartment Power supply -+ Locking of the cover ser.no ******** R ATEX Two-wire adjustment module terminal compartment (opening in Ex area permitted) Exd terminal compartment FM APPROVED Supply: 20...36V DC/4...
Electrical connection 4.3 Connection of the external indicating instrument VEGADIS 50 Loosen the four screws of the housing lid on VEGADIS 50. The connection procedure can be facilitated by fixing the housing cover during connection work with one or two screws on the right of the housing. VEGADIS 50 Adjustment module + - Tank 1 m (d) 12.
Electrical connection 4.4 Configuration of measuring systems A measuring system consists of a sensor with 4 … 20 mA signal output and a unit that evaluates and further processes the levelproportional current signal. On the following pages, you will see a number of instrument configurations, designated as "measuring systems“, some of which are shown with signal processing units.
Electrical connection Measuring system with VEGAPULS 42 or 44 on active PLC • • • • Two-wire technology, power supply from active PLC. Output signal 4 … 20 mA (passive). Measured value display integrated in the sensor. Optional external indicating instrument (can be mounted up to 25 m away from the sensor in Ex area). • Adjustment with PC, HART® handheld or the adjustment module MINICOM (can be plugged into the sensor or into the external indication instrument).
Electrical connection Measuring system with VEGAPULS 42 or 44 in four-wire technology • Four-wire technology, power supply and output signal via two separate two-wire cables. • Output signal 4 … 20 mA active. • Optional external indicating instrument with analogue and digital indication (can be mounted up to 25 m away from the sensor). • Adjustment with PC, HART® handheld or adjustment module MINICOM (can be plugged into the sensor or into the indicating instrument VEGADIS 50). • max.
Electrical connection Measuring system with VEGAPULS 42 or 44 via separator in Ex areas on active PLC (Ex ia) • Two-wire technology (loop powered), power supply via the signal line of the PLC; output signal 4 … 20 mA (passive). • Separator transfers the non intrinsically safe PLC circuit to the intrinsically safe circuit, so that the sensor can be used in Ex zone 1 or Ex zone 0. • Optional external indicating instrument with analogue and digital display (can be mounted up to 25 m away from the sensor).
Electrical connection Measuring system with VEGAPULS 42 or 44 via separator (Smart-Transmitter) on passive PLC (Ex ia) • Two-wire technology (loop powered), intrinsically safe ia supply via the signal cable of the separator for operation of the sensor in Ex zone 1 or Ex zone 0. • Output signal sensor 4 … 20 mA passive. • Output signal separator 4 … 20 mA active • Optional external indicating instrument with analogue and digital display (can be mounted up to 25 m away from the sensor).
Electrical connection Measuring system with VEGAPULS 42 or 44 on VEGADIS 371 Ex indicating instrument with current and relay output (Ex ia) • Two-wire technology (loop powered), intrinsically safe ia supply via the signal cable of the VEGADIS 371 Ex indicating instrument for operation of the sensor in Ex zone 1 or Ex zone 0. • Optional external indicating instrument with analogue and digital display (can be mounted up to 25 m away from the sensor).
Electrical connection VEGAPULS 42 Ex or 44 Ex (loop powered) with pressure-tight encapsulated connection compartment on active PLC (Ex d) • Two-wire technology, supply via the cable from active PLC to Exd connection housing for operation in Ex-Zone 1 (VEGAPULS …Ex) or Ex-Zone 0 (VEGAPULS …Ex0). • Output signal 4 … 20 mA (passive). • Measured value display integrated in the sensor.
Electrical connection VEGAPULS 42 Ex or 44 Ex with pressure-tight encapsulated connection compartment in four-wire technology (Ex d) • Four-wire technology, supply and output signal via two separate two-wire cables for operation in Ex-Zone 1 (VEGAPULS …Ex) or Ex-Zone 0 (VEGAPULS …Ex0). • Output signal 4 … 20 mA (active). • Optional external indicating instrument with analogue and digital display (can be mounted up to 25 m away from the sensor in Ex area).
Set-up 5 Set-up 5.1 Adjustment media 5.2 Adjustment with PC Radar sensors can be adjusted with the - PC (adjustment software PACTwareTM) - detachable adjustment module MINICOM - HART ® handheld. The adjustment must be carried out with only one adjustment device. If, for example, you attempt to adjust the parameters with the MINICOM and the HART ® handheld at the same time, the adjustment will not work.
Set-up + PLC Ri ≥ 250 Ω + 250 Ω PLC Ri < 250 Ω Rx VEGAMET/VEGALOG VEGAPULS 42, 44 and 45 – 4 … 20 mA 43
Set-up 5.3 Adjustment with adjustment module MINICOM Much like with the PC, you can set up and operate the sensor with the small, detachable adjustment module MINICOM. The adjustment module is simply plugged into the sensor or into the external indicating instrument (optional). Tank 1 m (d) 12.
Set-up Adjustment without medium (adjustment independent of the level) 2. Operating range Without special adjustment, the operating range corresponds to the measuring range. Generally, it is useful to choose a slightly wider range (approx. 5 %) for the operating range than for the measuring range. Key adjustment Sensor m(d) 4.700 Example: Min./max. adjustment: 1.270 … 5.850 m; adjust operating range to approx. 1.000 … 6.000 m. OK 3. Adjustment OK Max. 100 % (1.
Set-up + or OK – With the "+“ or " –“ key you can assign a level distance (example 5.85 m) to the previously adjusted percentage value. If you do not know the distance, you have to do a sounding. The adjusted product distance is written in the sensor and the display stops flashing. You thereby adjusted the lower product distance as well as the percentage filling value corresponding to the lower product distance.
Set-up • Confirm with "OK “. 7. Useful level, noise level If necessary, choose a decimal point. However, note that only max. 4 digits can be displayed. In the menu "prop. to“ you choose the physical quantity (mass, volume, distance…) and in the menu " Unit“ the physical unit (kg, l, ft3 , gal, m3 …). In the menu Linearisation: Adjust ment Signal condit ioning you get important information on the signal quality of the product echo.
Set-up Menu schematic for the adjustment module MINICOM Sensor PULS 54 K 2.00 m(d) 4.700 Parameter Multidrop operation (HART ® sensor address): • Sensor address zero: The sensor outputs beside the 4…20 mA signal also a digital (HART ®) level signal. • Sensor address 1…15: the sensor delivers only a digital (HART® ) level signal. The sensor current is frozen to 4 mA (power supply). After switching on, the sensor type and the software version are displayed for a few seconds.
Set-up With these keys you move in the menu field to the left, right, top and bottom ESC OK Add’l functions Info 6. 7. False echo memory act. dist. m (d) 4.700 Ampl.: XX dB S-N: XX dB Create new Update Delete Meas. dist. m (d) X.XX Meas. dist. m (d) X.XX Delete Now! OK? Create new OK?? Update Now! OK? Deleting! Learning! Learning! Reset to de fault Language English Reset Now! OK? Reset ing! Sensor Tag Sensor Sensor Serial type no. PULS54 1094 K 0213 Softw. Vers. 2.00 max. range.
Set-up 5.4 Adjustment with HART® handheld With any HART ® handheld you can set up the VEGAPULS series 40K radar sensors like all other HART® compatible sensors. A special DDD (Data Device Description) is not necessary. Just connect the HART® handheld to the signal cable, after having connected the sensor to power supply. + Ri ≥ 250 Ω Note: If the resistance of the power supply is less than 250 Ohm, a resistor must be connected into the signal/connection loop during adjustment.
Set-up Rx VEGAMET VEGAPULS 42, 44 and 45 – 4 … 20 mA VEGALOG 51
Diagnostics 6 Diagnostics 6.1 Simulation To simulate a certain filling level, you can call up the function “Simulation” in the adjustment module MINICOM, in the adjustment software PACTwareTM or in the HART® handheld. You simulate a vessel filling and thereby a certain sensor current. Please note that connected instruments, such as e.g. a PLC, react according to their adjustments and will probably activate alarms or system functions.
Technical data 7 Technical data 7.1 Technical data Power supply Power supply - four-wire sensor (non-Ex and Ex d ia) 24 V DC (20 … 72 V DC) 230 V AC (20 … 253 V AC), 50/60 Hz fuse 0.
Technical data Parameter and measuring range 1) Parameter VEGAPULS 42 - standard ø 40 mm horn - optional ø 48 mm horn ø 75, 95 mm horn VEGAPULS 44 - DN 50, ANSI 2“ - DN 80, 100, ANSI 3“, 4“, 6“ VEGAPULS 45 distance between product surface and process fitting (e.g.
Technical data Accuracy 1) (typical values under reference conditions, all statements relate to the nominal measuring range) Characteristics linear Resolution, general max. 1 mm Resolution of the output signal 1.6 µA or 0.01 % Accuracy see diagram 10 mm 3 mm -3 mm 0,5 m 30 m -10 mm Measurement characteristics 1) (typical values under reference conditions, all statements relate to the nominal measuring range) Min.
Technical data Ambient conditions Vessel pressure Ambient temperature on the housing - 4 … 20 mA two-wire sensor - 4 … 20 mA four-wire sensor - 4 … 20 mA four-wire sensor Ex d ia Process temperature (flange temp.
Technical data Weights Weights dependent on housing materials and Ex concepts. VEGAPULS 42 2.0 … 3.1 kg VEGAPULS 44 - DN 50 4.2 … 5.0 kg - DN 80 6.8 … 7.6 kg - DN 100 8.0 … 9.1 kg - DN 150 13.2 … 14.3 kg - ANSI 2“ 5.2 … 5.7 kg - ANSI 3“ 6.9 … 7.5 kg - ANSI 4“ 10.5 … 11.1 kg - ANSI 6“ 14.6 … 15.4 kg VEGAPULS 45 (plus meas. pipe weights) - G 1½ A or 1½“ NPT 2.0 … 3.8 kg - DN 50 4.2 … 6.0 kg - DN 80 5.9 … 7.7 kg - DN 100 7.0 … 8.8 kg - DN 150 11.8 … 13.7 kg - ANSI 2“ 3.7 … 5.6 kg - ANSI 3“ 6.2 … 8.
Technical data 7.2 Approvals Intrinsically safe in Ex environment When radar sensors are used in Ex areas or on ships, the instruments must be suitable and approved for the explosion zones and applications. The suitability is checked by the approval authorities and is certified in approval documents. Series 40 sensors in EEx ia (intrinsically safe) version require for use in Ex areas special separators or safety barriers. The separators or safety barriers provide intrinsically safe (ia) circuits.
Technical data 7.3 Dimensions External indicating instrument VEGADIS 50 85 82 38 85 118 108 135 10 48 ø5 Note: The diameter of the connection cable should be min. 5 mm and max. 9 mm. Otherwise the seal effect of the cable entry would not be ensured. Pg 13,5 Mounting on carrier rail 35 x 7.5 acc. to EN 50 022 or flat screwed Flange dimensions acc. to ANSI (RF) D = outer flange diameter d2 flange thickness diameter of hole circle seal ledge diameter seal ledge thickness 1 / 16" = approx. 1.
Technical data Sensor dimensions PBT Aluminium Aluminium with Exd terminal compartment 201 165 215 215 185 116 25 25 205 370 205 322 182 116 185 370 101 10˚ M20x1,5 M20x1,5 135 125 ½" NPT 20 19 139 ø 40 319 253 219 307 199 ø 40 ø 40 100 145 ø 40 18 22 PBT: 53 Al: 78 G½A 1½NPT 20 SW 60 ø 48 ø 75 G1½ A 1½" NPT G1½ A 1½" NPT ø 95 ø18 ø18 45 ˚ 45 8 ø1 ˚ VEGAPULS 42 ø 125 ø 160 ø 180 ø 165 ø 200 ø 220 DN 50 PN 40 (C) ANSI 2" (RF) DN 80 PN 40 (C) ANSI 3" (R
Technical data Recommended max. socket length depending on the antenna version: Socket length Socket length with antenna extension VEGAPULS 42 VEGAPULS 44 Standard DN50/ANSI 2“ DN 80/ANSI 3“ DN 100/ANSI 4“ DN 150/ANSI 6“ 135 mm 135 mm 210 mm 310 mm 310 mm 250 mm 245 mm 325 mm 425 mm 425 mm 125 22 319 29 125 18…22 ø 40 108 65 65 Version 20 Sensor type ø 165…285 ø 27 ø 27 ø22 L max. 4000 L max.
Supplement Supplement Safety Manual Functional safety acc. to IEC 61508 / IEC 61511 VEGAPULS series 40 radar sensors; 4 … 20 mA/HART® compact sensor 1 1.1 General Validity This safety manual applies to VEGAPULS series 40 radar sensors in two-wire version 4 … 20 mA/HART ®, called “measuring system”. 1.
Supplement 1.4 Determination of safety-related characteristics The failure limit values for a safety function, depending on the SIL class. Safety integrity level Low demand mode High demand or continuous mode SIL PFDavg PFH 4 >10-5 up to <10-4 >10-9 up to <10-8 3 2 >10-4 up to <10-3 >10 -3 up to <10-2 >10-8 up to <10-7 >10-7 up to <10-6 1 >10-2 up to <10-1 >10-6 up to <10-5 (from IEC 61508, part 1/7.6.
Supplement 2 2.1 Planning Low demand mode If the demand rate is only once a year, then the measuring system can be used as safetyrelevant subsystem in „low demand mode“ (see IEC 61508-4, 3.5.12). Corresponding characteristics : PFDavg (average probability of dangerous failure on demand). It is dependent on the test interval T Proof between the function tests of the protective function. 2.
Supplement 3 3.1 Set-up Mounting and installation The prevailing plant conditions influence the safety of the measuring system. Therefore note the mounting and installation instructions of the appropriate operating instructions manual. 3.2 Adjustment instructions and parameter adjustment Adjustment instructions The activation of the measuring system as safety-relevant subsystem is only possible via PC adjustment programs.
Supplement 4 Reaction during operation and in case of failure In case of modifications during operation, you have to take note of the safety functions. It must be ensured that the safety-relevant parameter adjustments remain activated. Occurring fault signals are described in the appropriate operating instructions manual. In case of detected failures or fault signals, the entire measuring system must be switched out of service and the process held in a safe condition by means of other measures.
Supplement 6 Safety-related characteristics The failure rate of the electronics and the antenna system was determined by an FMEDA (Failure Mode, Effects and Diagnostics Analysis) acc. to IEC 61508. The number values are based on an output current tolerance of max. 2 %. Architecture 1oo1D VEGAPULS VEGAPULS VEGAPULS VEGAPULS VEGAPULS SIL 2 41 42 43 44 45 Overfill protection Dry run protection Individual level Max Min HFT 0 SFF > 88% PFDavg 1) PFH [1/h] < 0.10 •10 -2 < 0.
Supplement SIL declaration of conformity Füllstand - Grenzstand - Druck SIL d e c l a r a t i o n of c o n f o r m i t y Functional safety according to IEC 61508 / IEC 61511 VEGA Grieshaber KG, Am Hohenstein 113, D-77761 Schiltach declares as manufacturer, that for the radar sensors of the product families VEGAPULS series 40 and 50 ( 4 ... 20 mA HART® ) the reliability (“proven in use”) was verified according to IEC 61508 / IEC 61511.
Supplement CE declaration of conformity VEGAPULS 42, 44 and 45 – 4 … 20 mA 69
Supplement 70 VEGAPULS 42, 44 and 45 – 4 … 20 mA
Supplement VEGAPULS 42, 44 and 45 – 4 … 20 mA 71
VEGA Grieshaber KG Am Hohenstein 113 77761 Schiltach Germany Phone (07836) 50-0 Fax (07836) 50-201 E-Mail info@de.vega.com www.vega.com ISO 9001 All statements concerning scope of delivery, application, practical use and operating conditions of the sensors and processing systems correspond to the information available at the time of printing.