Operating Instructions Electronics module VEGAPULS series 60 Document ID: 36801 Radar
Contents Contents 1 About this document 1.1 1.2 1.3 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General instructions . . . . . . . . . . . . . . . . . . . . . . . . . Mounting preparations . . . . . . . . . . . . . . . . . . . . . . . Mounting steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 7 8 Setup preparations . . . . . . . . . . . . . . . . . . . . . . . . . . Setup steps . . . . . . . . .
1 About this document 1 About this document 1.1 Function This operating instructions manual provides all the information you need for mounting, connection and setup as well as important instructions for maintenance and fault rectification. Please read this information before putting the instrument into operation and keep this manual accessible in the immediate vicinity of the device. 1.2 Target group This operating instructions manual is directed to trained qualified personnel.
2 For your safety 2 For your safety 2.1 Authorised personnel All operations described in this operating instructions manual must be carried out only by trained specialist personnel authorised by the plant operator. During work on and with the device the required personal protective equipment must always be worn. 2.2 Appropriate use Oscillator, emitting electronics, housing or process components are replacement components for existing sensors. 2.
3 Product description 3 Product description 3.1 Configuration Scope of the operating instructions manual This operating instructions manual applies to electronics modules with the following hardware and software versions: l l Scope of delivery Hardware from 2.0.0 Software from 4.0.
3 Product description Storage and transport temperature l l l l Dry and dust free Not exposed to corrosive media Protected against solar radiation Avoiding mechanical shock and vibration l Storage and transport temperature see chapter "Supplement Technical data - Ambient conditions" Relative humidity 20 … 85 % l 36801-EN-101008 6 Electronics module • VEGAPULS series 60
4 Mounting 4 Mounting 4.1 General instructions Sensor serial number The new electronics module must be loaded with the order and factory data of the sensor. These are the options: l l At the factory by VEGA Or on site by the user Information: When loading on site, first of all the order data must be downloaded from the Internet (see "Setup"). In both cases, the sensor serial number is necessary. The serial numbers are stated on the type label of the instrument, inside the housing or on the delivery note.
4 Mounting l l l l l PS60EE.60KE for version 4 … 20 mA/HART four-wire with increased sensitivity PS60EE.60KP for version Profibus PA PS60EE.60KK for version Profibus PA with increased sensitivity PS60EE.60KF for version Foundation Fieldbus PS60EE.60KL for version Foundation Fieldbus with increased sensitivity VEGAPULS 65, 66 l PS60EE.60CH for version 4 … 20 mA/HART l PS60EE.60CV for version 4 … 20 mA/HART four-wire l PS60EE.60CP for version Profibus PA l PS60EE.
4 Mounting Proceed as follows: 1 Switch off power supply 2 Unscrew housing cover of the electronics compartment 3 Remove the terminal blocks according to the operating instructions manual of the respective sensor 4 Loosen the two holding screws with a screwdriver (Torx size T 10 or Phillips size 4) 1 (+)1 2(-) 5 6 7 8 2 Fig. 3: Loosening the holding screws 1 2 Electronics module Screws (2 pcs.) 5 Pull the previous electronics out by using the pull-out tool.
5 Setup 5 Setup 5.1 Setup preparations With sensor serial number If you have ordered the electronics module by stating the sensor serial number, it is ready for the setup procedure after installation and connection to power supply. Without sensor serial number If you have ordered the electronics module without stating the sensor serial number or you are using a suitable electronics module from stock, you first have to load the sensor data after installation. Move via www.vega.
6 Maintain 6 Maintain 6.1 How to proceed in case of repair If a repair is necessary, please proceed as follows: You can download a return form (23 KB) from our Internet homepage www.vega.com under: "Downloads - Forms and certificates - Repair form". By doing this you help us carry out the repair quickly and without having to call back for needed information.
7 Dismounting 7 Dismounting 7.1 Dismounting steps Warning: Before dismounting, be aware of dangerous process conditions such as e.g. pressure in the vessel, high temperatures, corrosive or toxic products etc. Take note of chapters "Mounting" and "Connecting to power supply" and carry out the listed steps in reverse order. 7.2 Disposal The instrument consists of materials which can be recycled by specialised recycling companies.
8 Supplement 8 Supplement 8.1 Technical data Technical data 36801-EN-101008 are stated in the operating instructions manual of the appropriate sensor.
8 Supplement 36801-EN-101008 14 Electronics module • VEGAPULS series 60
36801-EN-101008 8 Supplement Electronics module • VEGAPULS series 60 15
Printing date: VEGA Grieshaber KG Am Hohenstein 113 77761 Schiltach Germany Phone +49 7836 50-0 Fax +49 7836 50-201 E-mail: info@de.vega.com www.vega.com ISO 9001 All statements concerning scope of delivery, application, practical use and operating conditions of the sensors and processing systems correspond to the information available at the time of printing.
