Instructions for Installation And Operation Attention: Do not remove the bindings holding the two extension arms until fully assembled. These are spring-loaded and can cause serious injury if allowed to spring free. Attention: Read this instruction manual carefully and completely before mounting and usage. Keep this manual for future reference. Dear Customer: Congratulations and thank you for buying an awning from us.
List of the parts 1|1PC 2|1PC 3|1PC 4|ST4.8x19|4PCS 5|2PCS 6|M12x45|4PCS 7|φ12|4PCS 8|2PCS 9|M10X80|4PCS 10|4PCS 11|2PCS 12|M10|2PCS 13-1|1PC 13-2|1PC 13-3|1PCS 14-1|2PCS 14-2|1PCS 15-1|1PC 15-2|1PC 15-3|1PCS 16|1PC 17|1PC 18|ST3.
1 4 19 25 26 13-1 25 16 9 24 14-1 8 15-2 21 14-2 13-3 15-3 18 13-2 20 14-1 15-1 10 3 22 5 2 7 6 17 23 12 11 Explosive drawing of Awning 33
Important Safety Instructions Warning: For your own and the safety of other persons it is important to follow below instructions and obey warnings. Symbol explanation This warning triangle calls attention to hazards that it can lead to death or to severe injuries or which is important for the functioning of the awning. This sign identifies important notes. Safety instructions To install this awning technical knowledge is necessary.
In case of rain retract the awning if tilt angle is less than 14°. Nobody is allowed to climb onto the awning. Hanging anything on the awning is forbidden. Sheeting was used to protect the paint. This must be removed afterwards. When extended, various forces, including wind and rain, will affect an awning. These sometimes substantial forces must be absorbed by the awning and transferred to the assembled structure via its mounting brackets.
Step 2: Roller assembly Keep the rollers aligned, assemble the roller with the connectors and secure it with the corresponding bolts as figure below : 13-3 13-1 18 13-2 Step 3: Torsion bar and arm assembly: keep the four face aligned , connect the torsion bar with the connectors and secure it with the corresponding bolts as figure below: 18 14-1 14-2 Then assembly the arm to the torsion bar as figure below.
Step4: Front bar assembly Connect the front bar with connectors and secure it with the corresponding bolts as figure below: . (please keep the front bar aligned). 15-1 18 15-2 Step 5: Front bar wrist support assembly: Slide the front bar feet into the front bar without tightening. As shown in the figure below: 11 15 11 11 11 15 15 11 Step 6: Arms with front bar assembly: Put front bar feet bolt through the hole of small arm, then position the front bar.
Step 7: Link the self-locking nut Link the self-locking nut into screw which at the bottom of the screw in front bar feet by a wrench, stop when the thread leakage 1 ~ 2 laps. As shown in the figure below: 12 ATTENTION: BEFORE BLOCKING THE NUT, ENSURE THAT THE ARMS ARE PROPERLY ALIGNED. Step8: Left roller support with gear box assembly: Hammer the left roller support with gear box into the left end of torsion bar by wood hammer, then tighten the left hexagon bolt by 5mm Hexagon wrench.
Step 9: Fabric and valance assembly: Open the fabric bag, Spread out both fabric 14A and valance 14B and use the cloth guiding wire to line through the fabric. As shown in the figure below: 22 24 23 24 24 Step 10: Roll inthe fabric on the roller Roll in the fabric on the roller, pay attention to the fabric direction needed, as shown in the figure below: Please face up the fabric when assembling. Keep the same spacing X at both ends. Spread the fabric slowly in case of damage.
Step 11: One end of fabric through the groove of front bar, well-distributed the fabric after pull in all fabric, then insert shaft of roller into the square hole of gear case. As shown in the figure below, A B A B If the part of front bar is a little deformed, please adjust it with tools by yourself.
Step 12: Right roller support assembly: Insert the shaft of roller into roll tube plug, meanwhile insert the torsion bar into the right roller supports with hitting. Then tighten the right hexagon bolt by 5mm Hexagon wrench. As shown in the figure below: Step 13: Assemble to make a whole awning Make the valance through groove of front bar, pay attention to the direction and make sure the left and right sides on average, then hitting the cover of front bar into end of front bar.
Installation procedure： Step 1: Draw lines on the wall Choose the position,then draw up the position of bolt holt hole by pencil as blow picture,please make sure hole the of each group on the same horizontally or vertically. Attention：figure in“ L ”is product’ s length ，the blow picture is mean the distance for brackets holes is L-14cm(For example: the product actual length of 3.6 m，the distance =3600mm-140mm=3460mm） ； longitudinal distance for holes is 10 cm.
Step 2. Installing the brackets Drill the hole according to the line which was draw up in step 1 by 14mm( or 5/8 inch) wall drill, please pay attention to the deep of hole that should not be less than 9cm. Making the expansion bolt through the bracket(keep the barbed side up), hitting the expansion bolt into the hole with tighten by wrench. As shown in the figure below: Or 5/8inch Step 3: Installing the awning: Install the awning into the brackets, and fasten the bolts of the brackets.
loose the bolts 14
Note: The awning is already delivered with an optimally adjusted tilt angle. However, users can adjust the screen angle within a range of 5° to 40° As shown in the figure: Step 6: The right way of the awning using The awning can be operated normally when finish adjusting the horizontal of the front bar. Please use the awning in right way.
Maintenance Regular maintenance will not only help to keep a long durability but it is also important for your own and the safety of other people. Examine regularly whether wall brackets are tight, if not, fasten them. Examine the gear box once half a year. If you find any damages, stop using until gear box has been repaired or renewed. Examine the bolts and nuts once half a year, fasten them if loose or lax. Stop using the awning immediately if it is has been damaged or it is not tighten properly.
