GARDEN SHED 8x12 ASSEMBLY MANUAL
STOP MISSING A PART? CALL US BEFORE GOING BACK TO THE STORE The store where you made your purchase Does not stock parts for this item. If you have assembly questions or you are missing or have damaged parts,please call 1-858-324-1911 (Mon - Fri, 10:00 am to 7:00 pm EST) you can also e-mail customerservice@veikous.com or visit www.veikous.com Please prefer email contact. Due to busy lines, there may be a wait for calls to be answered.
TOOlS Required Electric drill Gloves Tape Measure Ladder Pencil Safety Glasses Hammer Paint Tools Optional Nail Gun Hand Saw ORIENT LUMBER AND TRIM FOR BEST APPEARANCE Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way negatively affect the strength or integrity of our product.(See Fig A.B.C).
CONCRETE FOUNDATION If you choose to install your kit on a concrete slab refer to the diagram below. Caulk between sill plate and concrete. Concrete 4”(10.2cm) B C A Concrete Foundation Size 141.7”X95”(360 X 241.2cm) A B C 141.7”(360cm) 86.9”(221cm) 95”(241.2cm) Foundation material (Not Included) : X2 2x4x11.8’(5.1x10.2x360cm) X2 2x4x7.24’(5.1x10.2x221cm) X1 Caulk Note:Must be treated lumber. • A treated 2 x 4 (5.1 x 10.2 cm) sill plate is required when installing your shed on concrete.
BUILD YOUR OWN WOOD FLOOR OPTION (Materials not included.) C B A Wood Floor Size A B C 141.7”X95”(360 X 241.2cm) 141.7”(360cm) 86.9”(221cm) 95”(241.2cm) Foundation material (Not Included) : X2 2x4x11.8’(5.1x10.2x360cm) X8 2x4x7.24’(5.1x10.2x221cm) X2 4x4x11.8’(10.2x10.2x360cm) X3 X64 Note:Must be treated lumber. 5/8”x48”x96”(1.6x121.9x243.8cm) 3" (7.
ADDITIONAL MATERIALS (Not Included) After building your shed,you will need the following materials to make your shed waterproof and decorative. PAINT FOR SIDING --------------------------------------------(3 Gallons) Use 100% acrylic latex exterior paint. (2) coats recommended. PAINT FOR TRIM ----------------------------------------------(2 Quarts) Use 100% acrylic latex exterior paint.
PARTS IDENTIFICATION Part identification letters are stamped on certain parts. 1 1 Check these locations for part stamp. PARTS LIST AND SIZES √INVENTORY YOUR PARTS before you begin. X4 1 X23 3 X4 4 X1 6 X1 7 X6 8 X2 9 X4 10 X4 11 X4 12 X2 13 X4 14 X4 15 X2 16 X3 17 X1 18 2.36x1.57x24in (6x4x61 CM) 2.36x1.57x75.6in (6x4x192 CM) 2.36x1.57x70.5in (6x4x179 CM) 2.36x1.57x77.4in (6x4x196.6 CM) 2.36x1.57x58.7in (6x4x149 CM) 2.36x1.57x68in (6x4x172.8 CM) 2.36x1.57x30.
X8 19 X1 20 X4 21 X1 2.36x1.57x70.4in (6x4x178.8CM) 2.36x1.57x23.6in (6x4x60 CM) 1.97x1.97x76.9in (5x5x195.4 CM) 3.31x1.77x0.94in (8.4x4.5x2.4 CM) 22 25 X2 4.72x23.6x1in (12x60x2.5 CM) X2 23 2.36x2.36x57.7in (6x6x146.5 CM) X2 24 2.36x2.36x57.7in (6x6x146.5 CM) PANEL PARTS LIST Wall panels are 0.47in(1.2 cm) thick.
Ix1 DOOR Jx1 DOOR Hx1 WINDOW METAL ROOFING PE4x14 PE5x2 PE6x2 PE7x2 M11Ax4 M11Bx2 M13Ax2 M13Bx1
DOOR HARDWARE x1 x2 Lock with Screws x2 Door Latch Long Hinge HARDWARE ACCESSORIES F1x260 F2x44 F3x400 F4x60 F5x190 Vx260 NOTE: If a nail gun is used, nails may be used at the screws locations shown to speed up assembly. Nails must be the same length as the screws.
WALL INDEX Create your own style of shed. Choose your door location.Use this guide to find the corresponding wall construction and installlation pages. 8' x 12' Door on eave wall GABLE WALL 01 FRONT EAVE WALL 03 8' x 12' Door on gable wall BACK EAVE WALL 02 GABLE WALL 01 GABLE WALL 01 BACK EAVE WALL 02 FRONT EAVE WALL 04 GABLE WALL 05 BACK EAVE WALL 02 GABLE WALL 01 GABLE WALL 01 GABLE WALL 05 OPTION FRONT EAVE WALL 03 FRONT EAVE WALL 04 OPTION NOTE: Your door location may vary.
GABLE WALL 01 PARTS REQUIRED: 1 X2 X2 2.36x1.57x24in(6x4x61 CM) 2.36x1.57x70.5in(6x4x179 CM) 3 X5 4 F5x24 2.36x1.57x75.6in(6x4x192 CM) Arrange the parts edge to edge on the floor as shown. Measure and mark from the end of the boards.Secure with (2) F5 Screws at each connection and (4) F5 Screws at the seams. 47.2in (120cm) 70.5in (179cm) 94.5in (240cm) 24in (61cm) Flush Seam 4 1 Flush F5 1.57in (4cm) 75.
GABLE WALL 01 PARTS REQUIRED: X2 F3x50 C Flush Install wall panels with primer side up as shown. Secure wall panels with F3 Screws spaced 11.4 in (29 cm) horizontally and 12.8 in (32.6 cm) vertically. Flush 11.4in (29cm) 12.8in (32.
BACK EAVE WALL 02 PARTS REQUIRED: X7 3 X4 8 2.36x1.57x68in(6x4x172.8 CM) 2.36x1.57x75.6in(6x4x192 CM) F5x32 Arrange the parts edge to edge on the floor as shown. Measure and mark from the end of the boards.Secure with (2) F5 Screws at each connection and (4) F5 Screws at the seams. 136.1in (345.6cm) 113.5in (288.2cm) 91.7in (232.8cm) 68in (172.8cm) 44.4in (112.8cm) 22.6in Seam (57.4cm) Flush 75.6in (192cm) Flush 1.
BACK EAVE WALL 02 PARTS REQUIRED: X3 C F3x75 Flush Mark the wall board with a pencil as shown 2.83in (72MM) Install wall panels with primer side up as shown. Flush Secure wall panels with F3 Screws spaced 11.4 in (29 cm) 11.4in horizontally and 12.8 in (29CM) (32.6 cm) vertically. Flush Flush 2.83in (72MM) 2.83in (72MM) 12.8in (32.
FRONT EAVE WALL 03 PARTS REQUIRED: X6 3 8 X2 2.36x1.57x68in(6x4x172.8 CM) 2.36x1.57x75.6in(6x4x192 CM) X1 6 X3 2.36x1.57x77.4in(6x4x196.6 CM) X1 7 2.36x1.57x4.33in(6x4x11 CM) 18 X1 2.36x1.57x64.4in(6x4x163.6 CM) 2.36x1.57x58.7in(6x4x149 CM) X2 17 20 X1 9 2.36x1.57x23.6in(6x4x60 CM) F5x56 2.36x1.57x30.7in(6x4x78 CM) Arrange the parts edge to edge on the floor as shown. Measure and mark from the end of the boards.
FRONT EAVE WALL 03 PARTS REQUIRED: B1 A X1 X1 X1 B2 F3x75 Flush Mark the wall panels with a pencil before screwing in the screws as shown. 2.83in (72MM) A Flush 2.83in (72MM) B2 A Flush Flush Flush B1 2.
FRONT EAVE WALL 04 OPTION PARTS REQUIRED: 3 X7 2.36x1.57x68in(6x4x172.8 CM) 2.36x1.57x75.6in(6x4x192 CM) 6 X1 20 X1 2.36x1.57x77.4in(6x4x196.6 CM) 2.36x1.57x23.6in(6x4x60 CM) 7 X1 8 X2 F5x44 2.36x1.57x58.7in(6x4x149 CM) 9 X2 2.36x1.57x30.7in(6x4x78 CM) Arrange the parts edge to edge on the floor as shown. Measure and mark from the end of the boards.Secure with (2) F5 Screws at each connection and (4) F5 Screws at the seams. 136in (345.6cm) 115.3in (292.8cm) 91.7in (232.8cm) 68in (172.
FRONT EAVE WALL 04 OPTION PARTS REQUIRED: A X1 C X2 F3x83 Flush Mark the wall panels with a pencil before screwing in the screws as shown. 2.83in (72MM) A Flush Flush 2.83in (72MM) 2.
GABLE WALL 05 OPTION PARTS REQUIRED: X2 1 4 X2 2.36x1.57x24in(6x4x61 CM) X4 2.36x1.57x70.5in(6x4x179 CM) 3 X3 2.36x1.57x75.6in(6x4x192 CM) X1 18 17 2.36x1.57x4.3in(6x4x11 CM) F5x36 2.36x1.57x64.4in(6x4x163.6 CM) Arrange the parts edge to edge on the floor as shown. Measure and mark from the end of the boards.Secure with (2) F5 Screws at each connection and (4) F5 Screws at the seams. 240094.5in 80.2in 2038 70.5in 1790 (179cm) 24in 610 (203.8cm) 47.
GABLE WALL 05 OPTION PARTS REQUIRED: B1 X1 F3x42 X1 B2 Mark the wall panels with a pencil before screwing in the screws as shown.
GABLE UNITS PARTS REQUIRED: 10 X4 1.57x1.18x47.7in(4x3x121.2 CM) E1 X2 12 X4 2.36x1.57x52.6in(6x4x133.7 CM) 13 X2 2.36x1.57x19.6in(6x4x49.9 CM) 14 X4 X2 3x1x54.8in(7.6x2.5x139.2 CM) E2 15 X4 3x1x46.4in(7.6x2.5x117.
GABLE UNITS F3x22 E1 Mark the wall panels with a pencil before screwing in the screws as shown. Flush E1 Flush Flush Flush E1 E2 Flush Flush F3x14 Flush Flush 14 E2 E1 Mark the wall panels with a pencil before screwing in the screws as shown.
BACK / GABLE WALL INSTALLATION F3x8 BACK EAVE WALL F3 GABLE WALL
BACK / GABLE WALL INSTALLATION F3x8 F5x10 GABLE WALL F5 BACK EAVE WALL F5 GABLE WALL OPTIONAL: DOOR LOCATED ON 8'GABLE WALL F3
FRONT EAVE WALL INSTALLATION F3x16 GABLE WALL BACK EAVE WALL F3 GABLE WALL F3 FRONT EAVE WALL STANDARD: DOOR LOCATED ON 12'EAVE WALL OPTIONAL: DOOR LOCATED ON 8'GABLE WALL
FRONT EAVE WALL INSTALLATION F5x10 FRONT EAVE WALL F5 F5 BACK EAVE WALL
GABLE UNITS INSTALLATION F4x24 F4 F4 F4 F4
EAVE INSTALLATION 11 x4 F4x12 11 F4 F4 11 Flush 11
RAFTER INSTALLATION 16 x2 F3x20 F5x4 25 x2 F3 25 F3 F3 25 16 F3 16 F5 F5 F5 Flush 16 Center
ROOF BEAM INSTALLATION 19 x8 F4x16 F4 19 F4 19 F4 19 F4
METAL ROOFING INSTALLATION F1 V F1x108 Vx108 PE6 PE4 PE4 PE4 PE4 PE4 PE4 PE4 PE7 PE5
METAL ROOFING INSTALLATION F1 V F1x108 Vx108 PE5 PE4 PE4 PE4 PE4 PE4 PE4 PE4 PE7 PE6
FASCIA TRIM INSTALLATION 23 x2 24 24 x2 F3x24 F3 23 F3 23 24 F3 F3
RIDGE CAP INSTALLATION F1 V F1x16 M13A Vx16 M13B M13A M13A M13B F1 V M11A M11B M11A M11A M11B M11A M11A M11B
WINDOW INSTALLATION H H Use silicone sealant to seal the window Seal the window by applying a high quality exterior-grade caulk to the back of the frame near the edge before installation.
LEFT DOOR F2x9 When assembling the long hinge, please install the F2 Screws one hole apart as shown in the picture. F2 I I F2 I F2 RIGHT DOOR F2x9 When assembling the long hinge, please install the F2 Screws one hole apart as shown in the picture.
DOOR INSTALLATION F2x18 I F2 The long hinge is attached to the door frame as shown in the picture with the holes staggered on the other side.
DOOR HARDWARE INSTALLATION Door Latch X2 22 F3 Lock with Screws X1 F2x8 F3x2 Top door beam F2 Mark the location of the top and bottom door beams with a pencil, then punch holes with a suitable drill bit.
CORNER TRIM INSTALLATION 21 x4 F3x32 F3 F3 21 21 F3 21
ENJOY YOUR PRODUCT ! ENJOY YOUR PRODUCT !