GARDEN SHED 8x12 ASSEMBLY MANUAL Minimum of 4 people is required for a safe assembly of the product. You will receive a box and a wooden pallet for this product to be fully assembled. Please make sure all boxes arrived in good condition before assembling. It happens sometimes when boxes arrive separately due to postponed carrier's shipping, and your patience is really appreciated! You can also reach out to us at any time at customerservice @veikous.
STOP MISSING A PART? CALL US BEFORE GOING BACK TO THE STORE The store where you made your purchase Does not stock parts for this item. If you have assembly questions or you are missing or have damaged parts,please call 1-858-324-1911 (Mon - Fri, 10:00 am to 7:00 pm EST) you can also e-mail customerservice@veikous.com or visit www.veikous.com Please prefer email contact. Due to busy lines, there may be a wait for calls to be answered.
TOOlS Required Electric drill Gloves Tape Measure Ladder Pencil Safety Glasses Hammer Paint Tools Optional Nail Gun Hand Saw ORIENT LUMBER AND TRIM FOR BEST APPEARANCE Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way negatively affect the strength or integrity of our product.（See Fig A.B.C).
ADDITIONAL MATERIALS (Not Included) After building your shed you will need the following materials to make your shed waterproof and decorative. PAINT FOR SIDING --------------------------------------------(3 Gallons) Use 100% acrylic latex exterior paint. (2) coats recommended. PAINT FOR TRIM ----------------------------------------------(2 Quarts) Use 100% acrylic latex exterior paint.
PARTS IDENTIFICATION Part identification letters are stamped on some parts. 1 1 Check these locations for part stamp. PARTS LIST AND SIZES √INVENTORY YOUR PARTS before you begin. X4 1 X23 3 X4 4 X1 6 X1 7 X6 8 X2 9 X4 10 X4 11 X4 12 X2 13 X4 14 X4 15 X2 16 X3 17 X1 18 2.36x1.57x24in (6x4x61 CM) 2.36x1.57x75.6in (6x4x192 CM) 2.36x1.57x70.5in (6x4x179 CM) 2.36x1.57x77.4in (6x4x196.6 CM) 2.36x1.57x58.7in (6x4x149 CM) 2.36x1.57x68in (6x4x172.8 CM) 2.36x1.57x30.
X8 19 X1 20 X4 21 X1 2.36x1.57x70.4in (6x4x178.8CM) 2.36x1.57x23.6in (6x4x60 CM) 1.97x1.97x76.9in (5x5x195.4 CM) 3.31x1.77x0.94in (8.4x4.5x2.4 CM) 22 25 X2 4.72x23.6x1in (12x60x2.5 CM) X2 23 2.36x2.36x57.7in (6x6x146.5 CM) X2 24 2.36x2.36x57.7in (6x6x146.5 CM) PANEL PARTS LIST Wall panels are 0.47in(1,2 cm) thick.
Ix1 DOOR Jx1 DOOR Hx1 WINDOW METAL ROOFING PE4x14 PE5x2 PE6x2 PE7x2 M11x4 M11Ax2 M13x2 M13Ax1
DOOR HARDWARE x1 x2 Lock with Screws x2 Door Latch Long Hinge HARDWARE ACCESSORIES F1x260 F2x80 F3x400 F4x60 F5x190 Vx260 NOTE: If you are using a nail gun, nails may be used where screws are shown for quicker assembly. Length of nail must match screw length.
WALL INDEX Create your own style of shed. Choose your door location.Use this guide to find the corresponding wall construction and installlation pages. 8' x 12' Door on eave wall GABLE WALL 01 FRONT EAVE WALL 03 8' x 12' Door on gable wall BACK EAVE WALL 02 GABLE WALL 01 GABLE WALL 01 BACK EAVE WALL 02 FRONT EAVE WALL 04 GABLE WALL 05 BACK EAVE WALL 02 GABLE WALL 01 GABLE WALL 01 GABLE WALL 05 OPTION FRONT EAVE WALL 03 FRONT EAVE WALL 04 OPTION NOTE: Your door location may vary.
GABLE WALL 01 PARTS REQUIRED: 1 X2 X2 2.36x1.57x24in(6x4x61 CM) 2.36x1.57x70.5in(6x4x179 CM) 3 X5 4 F5x24 2.36x1.57x75.6in(6x4x192 CM) Arrange parts on edge on floor as shown. Measure and mark from end of boards. Secure with (2) F5 Screws at each connection and (4) F5 Screws at seams. 47.2in (120cm) 70.5in (179cm) 94.5in (240cm) 24in (61cm) Flush Seam 4 1 Flush F5 1.57in (4cm) 75.
GABLE WALL 01 PARTS REQUIRED: X2 F3x50 C Flush Install wall panels with primed side up as shown. Secure panel with F3 Screws spaced 11.4in(29cm)laterally and spaced 12.8in(32.6cm) longitudinal. Flush 11.4in (29cm) 12.8in (32.
BACK EAVE WALL 02 PARTS REQUIRED: 3 X7 X4 8 2.36x1.57x68in(6x4x172.8 CM) 2.36x1.57x75.6in(6x4x192 CM) F5x32 Arrange parts on edge on floor as shown. Measure and mark from end of boards. Secure with (2) F5 Screws at each connection and (4) F5 Screws at seams. 136.1in (345.6cm) 113.5in (288.2cm) 91.7in (232.8cm) 68in (172.8cm) 44.4in (112.8cm) 22.6in Seam (57.4cm) Flush 75.6in (192cm) Flush 1.
BACK EAVE WALL 02 PARTS REQUIRED: X3 C F3x75 Flush Mark the wall board with a pencil as shown 2.83in (72MM) Install wall panels with primed side up as shown.Secure panel with F3 Screws spaced 11.4in(29cm) laterally and spaced 12.8in(32.6cm) longitudinal. Flush 11.4in (29CM) Flush Flush 2.83in (72MM) 2.83in (72MM) 12.8in (32.
FRONT EAVE WALL 03 PARTS REQUIRED: X6 3 8 X2 2.36x1.57x68in(6x4x172.8 CM) 2.36x1.57x75.6in(6x4x192 CM) X1 6 X3 2.36x1.57x77.4in(6x4x196.6 CM) X1 7 2.36x1.57x4.33in(6x4x11 CM) 18 X1 2.36x1.57x64.4in(6x4x163.6 CM) 2.36x1.57x58.7in(6x4x149 CM) X2 17 20 X1 9 2.36x1.57x23.6in(6x4x60 CM) F5x56 2.36x1.57x30.7in(6x4x78 CM) Arrange parts on edge on floor as shown. Measure and mark from end of boards. Secure with (2) F5 Screws at each connection and (4) F5 Screws at seams. 136in (345.
FRONT EAVE WALL 03 PARTS REQUIRED: B1 A X1 X1 X1 B2 F3x75 Flush 2.83in (72MM) A Mark the wall panel with a pencil before making screws as shown. Flush 2.83in (72MM) B2 A Flush Flush Flush B1 2.
FRONT EAVE WALL 04 OPTION PARTS REQUIRED: 3 X7 2.36x1.57x68in(6x4x172.8 CM) 2.36x1.57x75.6in(6x4x192 CM) 6 X1 20 X1 2.36x1.57x77.4in(6x4x196.6 CM) 2.36x1.57x23.6in(6x4x60 CM) 7 X1 8 X2 F5x44 2.36x1.57x58.7in(6x4x149 CM) 9 X2 2.36x1.57x30.7in(6x4x78 CM) Arrange parts on edge on floor as shown. Measure and mark from end of boards. Secure with (2) F5 Screws at each connection and (4) F5 Screws at seams. 136in (345.6cm) 115.3in (292.8cm) 91.7in (232.8cm) 68in (172.8cm) 44.4in (112.
FRONT EAVE WALL 04 OPTION PARTS REQUIRED: A X1 C X2 F3x83 Flush 2.83in (72MM) A Mark the wall panel with a pencil before making screws as shown. Flush Flush 2.83in (72MM) 2.
GABLE WALL 05 OPTION PARTS REQUIRED: X2 1 4 X2 2.36x1.57x24in(6x4x61 CM) X4 2.36x1.57x70.5in(6x4x179 CM) 3 X3 2.36x1.57x75.6in(6x4x192 CM) 18 2.36x1.57x4.3in(6x4x11 CM) F5x36 2.36x1.57x64.4in(6x4x163.6 CM) Arrange parts on edge on floor as shown. Measure and mark from end of boards. Secure with (2) F5 Screws at each connection and (4) F5 Screws at seams. 240094.5in 80.2in 2038 70.5in 1790 (179cm) 24in 610 14.3in 362 (36.2cm) (240cm) (203.8cm) 47.
GABLE WALL 05 OPTION PARTS REQUIRED: B1 X1 F3x42 X1 B2 Mark the wall panel with a pencil before making screws as shown.
GABLE UNITS PARTS REQUIRED: 10 X4 1.57x1.18x47.7in(4x3x121.2 CM) E1 X2 12 X4 2.36x1.57x52.6in(6x4x133.7 CM) 13 X2 2.36x1.57x19.6in(6x4x49.9 CM) 14 X4 X2 3x1x54.8in(7.6x2.5x139.2 CM) E2 15 X4 3x1x46.4in(7.6x2.5x117.
GABLE UNITS F3x22 E1 Mark the wall panel with a pencil before making screws as shown. Flush E1 Flush Flush Flush E1 E2 Flush Flush F3x14 Flush Flush 14 E2 E1 15 Mark the wall panel with a pencil before making screws as shown.
BACK / GABLE WALL INSTALLATION F3x8 BACK EAVE WALL F3 GABLE WALL
BACK / GABLE WALL INSTALLATION F3x8 F5x10 GABLE WALL F5 BACK EAVE WALL F5 GABLE WALL OPTIONAL: DOOR LOCATED ON 8'GABLE WALL F3
FRONT EAVE WALL INSTALLATION F3x16 GABLE WALL BACK EAVE WALL F3 GABLE WALL F3 FRONT EAVE WALL STANDARD: DOOR LOCATED ON 12'EAVE WALL OPTIONAL: DOOR LOCATED ON 8'GABLE WALL
FRONT EAVE WALL INSTALLATION F5x10 FRONT EAVE WALL F5 F5 BACK EAVE WALL
GABLE UNITS INSTALLATION F4x24 F4 F4 F4 F4
EAVE INSTALLTION 11 x4 F4x12 11 F4 F4 11 Flush 11
RAFTER INSTALLTION 16 x2 F3x20 F5x4 25 x2 F3 25 F3 F3 25 16 F3 16 F5 F5 F5 Flush 16 Center
ROOF BEAM INSTALLTION 19 x8 F4x16 F4 19 F4 19 F4 19 F4
METAL ROOFING INSTALLTION F1 V F1x108 Vx108 PE6 PE4 PE4 PE4 PE4 PE4 PE4 PE4 PE7 PE5
METAL ROOFING INSTALLTION F1 V F1x108 Vx108 PE5 PE4 PE4 PE4 PE4 PE4 PE4 PE4 PE7 PE6
FASCIA TRIM INSTALLTION 23 x2 24 24 x2 F3x24 F3 23 F3 23 24 F3 F3
RIDGE CAP INSTALLTION F1 V F1x16 M13 Vx16 M13A M13 M13 M13A F1 V M11 M11A M11 M11 M11A M11 M11 M11A
WINDOW INSTALLTION H H Using silicone sealant to seal the window Apply high quality exterior-grade caulk behind frame near edge before installing to seal window.
LEFT DOOR F2x17 F2 I RIGHT DOOR F2x17 F2 J
DOOR INSTALLTION F2x34 I F2 J F2
DOOR HARDWARE INSTALLTION Door Latch X2 22 F3 Lock with Screws X1 F2x8 F3x2 Top door beam Use a pencil to mark the position of the top and bottom door beams and punch holes with a suitable drill bit.
CORNER TRIM INSTALLATION 21 x4 F3x32 F3 F3 21 21 F3 21 CORNER TRIM INSTALLATION
ENJOY YOUR PRODUCT ！ ENJOY YOUR PRODUCT ！
