Assembly instructions Manual

ManualsBrandsVelleman projects ManualsHardwareK5600R

Total solder points: 1400

Difficulty level:

beginner 1o 2o 3o 4þ 5o advanced

PARTLIST H5600P-ED1

K5600

ADVERTISEMENT LED DISPLAY

þ Create your own message for personal advertisements.

þ Can be used for home, shop, car or truck…

þ 12 self definable characters.

þ 150 bright LED’s supplied with the kit.

þ Many spectacular light effects on the message, (scrolling, blinking,

rolling, panning…).

þ Adjustable effect speed.

þ Vertical or horizontal position possible

þ Fixed displaying is possible (no effects).

þ Different displays can be synchronised, to create longer messages,

or to create giant advertisements.

þ Special housing available order nr: B5600

þ Extra LED’s available, order nr: K/LEDHR (red) and K/LEDHG

(green)

Specifications

• 12 character positions

• 5 x 7 LED matrix for each character

• Bright LED’s, 60 to 80mcd

• Microprocessor technology

• Oscillator output for synchronisation with other display(s) (master /

slave configuration)

• Power supply: 12 to 28VDC (adapter type PS1208 for Europe)

• Reverse polarity protected

• Consumption: 760mA

• Dimensions: 80mm x 473mm

modifications reserved

Summary of content (14 pages)

PAGE 1
Total solder points: 1400 Difficulty level: beginner 1o 2o 3o 4þ 5o advanced K5600 ADVERTISEMENT LED DISPLAY þ Create your own message for personal advertisements. þ Can be used for home, shop, car or truck… þ 12 self definable characters. þ 150 bright LED’s supplied with the kit. þ Many spectacular light effects on the message, (scrolling, blinking, rolling, panning…). þ Adjustable effect speed. þ Vertical or horizontal position possible þ Fixed displaying is possible (no effects).
PAGE 2
5% 1% 4K7= ( 4 - 7 - 2 - B ) I P C CODICE CODIGO O COLORE DE D CORES E 0 1 2 3 4 5 6 7 8 9 A B Nero Marrone Rosso Aranciato Giallo Verde Blu Viola Grigio Bianco Argento Oro Preto Castanho Encarnado Laranja Amarelo Verde Azul Violeta Cinzento Branco Prateado Dourado COLOR= 2… 5 4K7= ( 4 - 7 - 0 - 1 - 1 ) E CODIGO DE COLORES Negro Marrón Rojo Naranjado Amarillo Verde Azul Morado Gris Blanco Plata Oro SF VÄRI KOODI Musta Ruskea Punainen Oranssi Keltainen Vihreä Sininen Purppura Harmaa Valkoinen Hopea
PAGE 3
__________________________________________________________________________________________________________________________________________________________ ASSEMBLY STEPS Required tools to assemble the kit: Use a small soldering iron of max. 40W. Use thin (1mm) solder, do not use any flux. Use a small cutter to trim the excess wires. 1. 2. 3. 4. Mount the components against the PCB surface and carefully solder the leads in place.
PAGE 4
_______________________________________________________________________________________________________________________________________________________ DIAGRAM R1 T2 T3 T4 T5 T6 T7 LD2 LD3 LD4 L-53ID LD5 CHARACTER1 LD9 L-53ID LD1 LD8 L-53ID +V T78 T79 T80 T81 T82 T83 T84 CHARACTER12 L-53ID L-53ID L-53ID 68 R94 68 R95 68 R96 L-53ID L-53ID L-53ID Vcontrol C2 10n L-53ID L-53ID L-53ID L-53ID L-53ID +V1 8 7 RST Vcc 4 GND 1 L-53ID L-53ID L-53ID L-53ID L-5
PAGE 5
__________________________________________________________________________________________________________________________________________________________ 5
PAGE 6
_______________________________________________________________________________________________________________________________________________________ 1. JUMPERS 4. IC SOCKET (Check the position of the notch!) 1 IC... q J1 2. DIODES (Check the polarity!) q IC1: 18P q IC2: 8P 5. TRANSISTORS D... CATHODE q D1… D24: 1N4148 q D25: 1N4000…. 4007 T... 3. ¼W RESISTORS MAX 8mm ! R...
PAGE 7
__________________________________________________________________________________________________________________________________________________________ 6. CAPACITORS 9. RESISTOR TRIMMERS C... RV... q q q q q C1: 3n3 (3300, 333) C2: 10n (10000, 103) C3: 100n (µ1, .1, 104) C4: 100n (µ1, .1, 104) C5: 100n (µ1, .1, 104) 7. ELECTROLYTIC CAPACITOR q RV1: 47K (50K) 10. INSERT THE IC * (Check the position of the notch!) (Check the polarity!) 1 C... PIN 1 IC... + q C6: 1µF q C7: 100µF 8.
PAGE 8
_______________________________________________________________________________________________________________________________________________________ 12. LEDs (Check the polarity!) LD... CATHODE q LD1… LDxx type L-53ID or L-53SGD The position of the LED’s will determine each character. The following list is only a guideline, other characters can be made, limited only by your imagination. Bold characters can be made by using two positions to create one character.
PAGE 9
__________________________________________________________________________________________________________________________________________________________ 9
PAGE 10
_______________________________________________________________________________________________________________________________________________________ 10
PAGE 11
__________________________________________________________________________________________________________________________________________________________ MORE INTERNATIONAL CHARTACTERS 11
PAGE 12
_______________________________________________________________________________________________________________________________________________________ 13.CONNECTION AND USE A- Power supply: Connect the unit to a DC supply voltage from minimum 12V to maximum 28V. A standard 12V / 800mA adapter (our type PS1208) can also be used, the inside of the connector must be connected to the positive terminal. Standard wires can also be used and soldered at the + and - connection. - + SW 12...
PAGE 13
__________________________________________________________________________________________________________________________________________________________ CONNECTION AND USE (continued from page 11) C- Use as a fixed display: If no effects are wanted, and only a fixed message is needed, mount a jumpwire at position JC, next to IC1. shunt IC1 JC 1 FIG 3 D- Speed adjustment: The speed of the effects can be adjusted by means of RV1.
PAGE 14
_______________________________________________________________________________________________________________________________________________________ 14.MOUNTING INTO THE OPTIONAL HOUSING A special housing can be ordered, type: B5600 • Disassemble the housing by removing the front and side panels. • Drill a pass through hole into the housing where supply wire is desired (side, back, top, bottom…).