Total solder points: 202 Difficulty level: beginner 1 2 3 4 5 advanced PIC® programmer board K8076 ge a wide ran m ra g ro p can controllers This board IC™ micro P ® ip h c of Micro ILLUSTRATED ASSEMBLY MANUAL H8076IP-1
This device complies with Part 15 of the FCC Rules provided the enclosed instructions are followed to the letter. Use of the device is subject to the following conditions: (1) this device must not cause harmful interference and (2) the operation of this device should not be influenced by unwanted interference. More information about FCC can be look at http://www.fcc.
Features & Specifications Features: onboard configurable 40 pin. ZIF socket Microcontroller selection using patch jumper easy to use programming PICprog2006TM software included SUBD connector set included Specifications: power supply: 15V DC, min. 300mA adapter (Ex. PS1508) serial port connector: 9 p. SUBD dimensions: 132x65x20mm / 5,23 x 2,57 x 0,79" currently supported controllers (rev. 2.0.0.
Assembly hints 1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools: • A good quality soldering iron (25-40W) with a small tip. • Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’and will protect the tip, and enables you to make good connections.
Assembly hints 1.
Construction 1. Diodes. Watch the polarity! D1 D2 D3 D4 : : : : 1N4007 1N4148 1N4148 1N4148 CATHODE 3. Metal film resistors R... D... R10 : 47 R11 : 220 2. Resistors (4 - 7 - 0 - B - 9) (2 - 2 - 1 - B - 9) 4. Voltage regulator R... R1 R2 R3 R4 R5 R6 R7 R8 R9 : : : : : : : : : 1K5 3K3 3K3 3K3 3K3 100K 100K 100K 10K (1 - 5 - 2 - B) (3 - 3 - 2 - B) (3 - 3 - 2 - B) (3 - 3 - 2 - B) (3 - 3 - 2 - B) (1 - 0 - 4 - B) (1 - 0 - 4 - B) (1 - 0 - 4 - B) (1 - 0 - 3 - B) 5.
Construction 7. Transistors. 10. Headers 12. Board to wire connector T1 : BC547 T2 : BC557 8. Voltage regulator SK3 : 5 poles SK4 : 5 poles VR2 : UA78L05 SK5 : 20P SK6 : 20P VR... 11. DC - Jack 9. LEDs. Watch the polarity ! LD1: 3mm LD2: 3mm LD3: 3mm LD4: 3mm 8 COLO R= 2...5 Green Yellow Yellow Red CATHODE LD ... SK1 : 15VDC (Power) 13. Electrolytic Capacitor. Watch the polarity ! C4 C5 C6 C7 C8 C9 C10 : 10µ F : 10µ F : 1µ F : 1µ F : 1µ F : 1µ F : 220µ F C...
Construction 14. Sub D - connector 16. IC’s. Watch the position of the notch! SK2 : RS232 (9p female) 15. ZIF socket IC1 : MAX232 IC2 : CD4049 17. Rubber feet Mount the rubber feet on the solder side of the PCB, see fig 1.0. SK5 : 40p FIG 1.
Construction 18. Serial cable 5 4 9 3 8 2 7 SK1 SUBD 9-POLE MALE 6 1 1 2 6 3 7 4 8 9 5 Mount a SUBD connector on both sides of a shielded 6-core cable. Refer to fig. 2.0 below. SK2 SUBD 9-POLE FEMALE FIG 2.0 . 10 If you do not assemble cables with the included SUBD connectors, pay attention to the following: all conductors must be connected “PIN to PIN”.
Construction Now, mount a enclosure over each SUBD connector according to fig. 3.0 FIG 3.0 .
Software 19. PIC - selection cable Cut off a piece of each wire of the female 'board-to-wire' connector so there is 6cm of wire left on the connector. See fig. 4.0 Cut off 5 pieces of shrinkable tube with a lenght equal to 1cm. Slide the shrinkable tube over the wires of the female 'board to wire'-connector (fig. 5.
Software installation 20. Software installation • Place the Velleman® software CD in your CD-ROM player. • Select ‘Browse through this CD for other Velleman software’(this message will not be displayed on your screen if ‘AUTORUN’is not activated). • Select the ‘K8076’folder. • Run the ‘SETUP.EXE’program in the 'C:\K8076\’folder. • Follow the indications on the screen until all files are installed. For connecting, testing and using this kit please refer to the programme help file on the included CD.
Schematic diagram 21. Schematic diagram.
PCB 22.
VELLEMAN Components NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com Modifications and typographical errors reserved © Velleman Components nv.
