CAMSET5A --- VERSION II OWNER'S MANUAL CAR REAR VIEW SYSTEM
CAR REAR VIEW SYSTEM The camera included is designed for use with the monitor supplied and is not suitable for connection to any other monitor. The monitor can be hooked up to two cameras. For optional camera, contact your local dealer. Please read before installing this system. KITS CONTENTS 1. 2. 3. 4. 5. 6. 7. 5" black and white car rear view monitor Water proofed camera with built-in microphone and 1.8m (female plug) 20m cable with male/male plug. Sun shield plastic.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lighting flash with arrowhead symbol, within and equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
7. Damage Requiring Service - The unit should be serviced by qualified service personnel when : - The power cord or the plug has been damaged. - Objects have fallen or liquid has been spilled into the unit. - The unit has been exposed to rain. - The unit does not appear to operated normally or exhibits a marked change in performance. - The unit has been dropped or the enclosure is damaged. 8. Replacement Parts - Use only manufacturer specified parts.
CAMERA INSTALLATION CAMERA (CAM13) 1.8m, 6 PIN CABLE WITH MINI DIN PLUG (FEMALE) WASHER SPRING WASHER SCREW 20m, 6 PIN CABLE WITH MINI DIN PLUG (MALE) BRACKET (CAMERA) 1. At camera mounting position, fit the camera mounting bracket ! to this position using the screws to the centre hole and slide hole. 2. Turn the bracket left and right to a correct direction and then tighten the screws. 3. Fit the camera to the bracket using the supplied washers ", spring washers # and screws $. 4.
MONITOR INSTALLATION 1. At the monitor mounting position, placing the monitor mounting bracket # and screw into the centre hole and slid holes. Adjusting the bracket by turning it left and right to let the monitor face to you directly. Then tightening the bracket. 2. Mounting the monitor onto the bracket by using the screws ". Moving the monitor up and down to a proper position and fixing the screws. 3. If necessary sticking the Sun shield % onto the top side of the monitor.
CONNECTION TO MONITOR IMPORTANT : Do not connect any camera to the monitor while monitor is switched on. 1. Plug the camera into the camera input DIN sockets marked A and B at the back of the monitor. Ensure that the arrow on the camera plug is at the top before inserting the plug into the input sockets. 2. Clipping the cables using the applied cable clip and screw the cable clip into the holes just beside the DIN sockets GND on the back of the monitor. (Black) 3.
FUNCTION DESCRIPTION % Power-on switch Push this button you can view the picture. Normally leave it unpushed when the monitor is used in backing a truck or a car. When you shift the gear in reverse, the unit will automatically display the picture of camera A no matter the power is on or off. " Contrast control Normally, it is not necessary to touch this control. When needed, turn it clockwise to increase the contrast and vice versa.
( Normal image / Mirror image Select Switch Please note that this switch has been set to mirror (Rev. Image) position by manufacturer. When you want to view from behind while you are backing a truck car, be sure to set this select switch to the (Rev. Image) position. In this case, check to see if the image appearing on the display is reversed right to left, just as it appears on a rear-view mirror. Rear view of monitor showing input/output connections.
SPECIFICATIONS MONITOR CAMSET5A Scanning frequency Video input Size of display Scanning size Resolution at centre Shock Vibration Input voltage Case Operating temperature Dimensions CAMERA CAM13 Pick-up device Scanning system Number of pixels Fixed focus lens Horizontal 15625Hz -CCIRVertical 50Hz -CCIR1Vpp / 75Ω 5" CRT 86% min. (horizontal) 500 lines 6.8G 0 to 2000Hz DC 12-24V ABS plastic 0 to +40°C 143 x 190 x 136mm 1/3" CCD 625 lines -CCIR512 x 582 pixels F3.6mm , F2.
