HQWS10001 USER MANUAL HANDLEIDING MODE D'EMPLOI MANUAL DEL USUARIO BEDIENUNGSANLEITUNG INSTRUKCJA OBSŁUGI MANUAL DO UTILIZADOR 3 14 25 36 47 58 69
HQWS10001 V.
HQWS10001 USER MANUAL 1. Introduction To all residents of the European Union Important environmental information about this product This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service.
HQWS10001 3. General Guidelines • Refer to the Velleman® Service and Quality Warranty on the last pages of this manual. • All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty. Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty. • 4.
HQWS10001 The digit on the right indicates the amount of available frequencies. Once the scan completed, the radio will tune itself to the first alphabetically listed station available in DAB mode. Press the on-off button again to put the appliance in standby mode. Switching Off Press and hold the on-off button until the appliance switches off, or just press the button briefly to cancel the standby mode. 5.
HQWS10001 The radio will scan through the available channels. All the channels will be shown in alphabetical order. Manual DAB Tuning Select [Manual Tune] to manually tune the radio. Use the tuning/enter dial to tune the radio in and press the same dial to keep the current tuning. Save as a preset if required. This helps in getting a clearer signal in areas where signal is poor.
HQWS10001 Manually Tune FM Use the tuning/enter dial to manually tune the radio in FM mode. Save as a preset if required. This helps in getting a clearer signal in areas where signal is poor. FM Menu Options Press and hold the info/menu button until [Scan Setting] is displayed. Use the tuning/enter dial to cycle through the options.
HQWS10001 AUX Menu Option Press and hold the info/menu button until [System] is displayed. Press the tuning/enter dial to select the [System] option. 5.6 System Options System Menu Options Press and hold the info/menu button until [Scan Setting] is displayed in either DAB or FM mode, or [System] is displayed in AUX mode. Turn the tuning/enter dial to cycle to the [System] option and press the same dial to select.
HQWS10001 Time/Date This option allows you to manually set the time and date. Once selected from the [Time] submenu, you will see the hours flashing. Turn the tuning/enter dial to cycle through the hours and press the same dial to select the required hour value. Once the hours have been set, the minutes are flashing. Repeat the process above and set the minutes. Once selected, you will move on to the next screen for setting the date.
HQWS10001 Dim This option lets you set the inactive display light level. Choose from the options by turning the tuning/enter dial and press the same dial to select: High → Med → Low The asterisk in the top right corner indicates the current selection. Inactive Standby (Step) You can set the auto standby time with this feature. Choose from the options by turning the tuning/enter dial and press the same dial to select: Off → 2 → 4 → 5 → 6 hours Each value is a period of minutes.
HQWS10001 5.8 DAB/FM Information Information Details When listening in DAB or FM mode, press the info button to cycle through the available information from the broadcasting service and the radio.
HQWS10001 Setting the Alarm Cycle to the option by using the tuning/enter dial and press the same dial to select it. Once an option has been selected it will move on to the next value to set until the process is complete.
HQWS10001 7. Technical Specifications power supply adapter ............................................................................................. 5 VDC, 1 A batteries ....................................................................... 4 x 1.5 V C cell (not incl.) speaker output ........................................................................................ 2 x 2.5 W IP rate ...........................................................................................................
HQWS10001 HANDLEIDING 1. Inleiding Aan alle ingezetenen van de Europese Unie Belangrijke milieu-informatie betreffende dit product Dit symbool op het toestel of de verpakking geeft aan dat, als het na zijn levenscyclus wordt weggeworpen, dit toestel schade kan toebrengen aan het milieu. Gooi dit toestel (en eventuele batterijen) niet bij het gewone huishoudelijke afval; het moet bij een gespecialiseerd bedrijf terechtkomen voor recyclage.
HQWS10001 het toestel alleen aan op een voedingsbron die wordt aangegeven op de achterkant van het toestel. Om gevaar voor brand en elektrische schokken te voorkomen, laat het onderhoud steeds uitvoeren door een vakman. 3. 4. Algemene richtlijnen • • Raadpleeg de Velleman® service- en kwaliteitsgarantie achteraan deze handleiding. • Gebruik het toestel enkel waarvoor het gemaakt is. De garantie vervalt automatisch bij ongeoorloofd gebruik.
HQWS10001 De teller rechts geeft het aantal gevonden zenders weer. Na het scannen geeft de radio de gevonden zenders in alfanumerieke volgorde weer. Druk nogmaals op de aan/uit-knop om het toestel in stand-bymodus te zetten. Uitschakelen Houd de aan/uit-knop ingedrukt totdat het toestel is uitgeschakeld of druk kort op de knop om de stand-bymodus te deactiveren. 5.2 Bedieningen De knoppen gebruiken In deze handleiding wordt van een “korte druk” uitgegaan, tenzij anders aangegeven.
HQWS10001 De radio doorloopt de beschikbare kanalen. Alle kanalen worden in alfabetische volgorde weergegeven. DAB-zenders handmatig afstemmen Selecteer [Manual Tune] om handmatig op een radiozender af te stemmen. Gebruik de draaiknop 'Tuning/Enter' om de radio af te stemmen en druk op dezelfde knop om op de geselecteerde zender af te stemmen. Sla deze zender op als voorinstelling. Dit is ideaal in situaties waar het signaal van een zender zwak is.
HQWS10001 Handmatig afstemmen op FM-radiozenders Gebruik de draaiknop 'Tuning/Enter' om de radio handmatig af te stemmen in FMmodus. Sla deze zender op als voorinstelling. Dit is ideaal in situaties waar het signaal van een zender zwak is. FM-menuopties Houd de knop 'Info/Menu' ingedrukt totdat [Scan Setting] wordt weergegeven. Gebruik de draaiknop 'Tuning/Enter' om door de opties te scrollen.
HQWS10001 AUX-menuoptie Houd de knop 'Info/Menu' ingedrukt totdat [System] wordt weergeven. Druk op de knop 'Tuning/Enter' om de optie [System] te selecteren. 5.6 Systeemopties Systeemmenu-opties Houd de info/menu-knop ingedrukt totdat [Scan Setting] wordt weergeven in DAB- of FM-modus of [System] in AUX-modus. Draai aan de knop 'Tuning/Enter' om door de opties te scrollen en druk op dezelfde knop om te selecteren. Gebruik dezelfde knop om door de opties te scrollen en om de gewenste optie te selecteren.
HQWS10001 Time/Date (tijd/datum) Met deze optie kunt u de datum en tijd handmatig instellen. Selecteer Time/Date in het submenu [Time]. De uurweergave begint te knipperen. Draai aan de knop 'Tuning/Enter' om door de uren te scrollen en druk op dezelfde knop om de gewenste waarde te selecteren. Na het instellen van de uren, knippert de minutenweergave. Herhaal de bovenstaande stappen en stel de minuten in. Ga naar het volgende scherm om de datum in te stellen.
HQWS10001 Dimmen Met deze optie kunt u de achtergrondverlichting van een inactief scherm instellen. Draai aan de knop 'Tuning/Enter' om door de opties te scrollen en druk op dezelfde knop om een optie te selecteren: High → Med → Low Het sterretje rechtsboven geeft de huidige selectie weer. Inactieve Standby (sleep) Met deze functie kunt u de automatische stand-bytijd instellen.
HQWS10001 Voorinstelling oproepen Om een voorinstelling van 1-5 op te roepen, druk op één van de voorkeuzenummers om een opgeslagen station op te roepen. Om een voorinstelling van 6-10 op te roepen, druk op 'shift' gevolgd door één van de voorkeuzenummers om een opgeslagen station op te roepen. Opmerking: Wanneer de radio wordt losgekoppeld van de stroombron of als de batterijen worden verwijderd, worden alle opgeslagen instellingen gewist. 5.
HQWS10001 Het alarm instellen Gebruik de draaiknop 'Tuning/Enter' om door de beschikbare opties te scrollen en druk op deze knop om een optie te selecteren. Zodra een optie is geselecteerd, wordt de volgende waarde geactiveerd totdat het proces is voltooid.
HQWS10001 7. Technische specificaties voeding adapter ............................................................................................. 5 VDC, 1 A batterijen ....................................................... 4 x 1.5 V C-batterij (niet meegelev.) luidsprekeruitgang ................................................................................... 2 x 2.5 W IP-norm .........................................................................................................IPX3 frequentie FM .
HQWS10001 MODE D'EMPLOI 1. Introduction Aux résidents de l'Union européenne Informations environnementales importantes concernant ce produit Ce symbole sur l'appareil ou l'emballage indique que l’élimination d’un appareil en fin de vie peut polluer l'environnement. Ne pas jeter un appareil électrique ou électronique (et des piles éventuelles) parmi les déchets municipaux non-sujets au tri sélectif ; une déchetterie traitera l’appareil en question.
HQWS10001 électrique, confier toute réparation à du personnel qualifié ou équivalent. 3. Directives générales • Se référer à la garantie de service et de qualité Velleman ® en fin de ce mode d'emploi. • Toute modification est interdite pour des raisons de sécurité. Les dommages occasionnés par des modifications par le client ne tombent pas sous la garantie. N’utiliser l'appareil qu’à sa fonction prévue. Un usage impropre annule d'office la garantie. • 4.
HQWS10001 Le numéro à la droite de l’affichage indique le nombre de stations trouvées. Une fois la recherche terminée, les stations sont classées par ordre numérique, puis alphabétique. Appuyer à nouveau sur le bouton pour mettre la radio en mode veille. Éteindre Maintenir enfoncé le bouton on/off jusqu‘à ce que l'appareil s‘éteigne ou appuyer brièvement pour désactiver le mode veille. 5.
HQWS10001 La radio recherche à travers toutes les stations disponibles. Toutes les stations trouvées sont affichées par ordre alphabétique. Régler manuellement DAB Pour régler manuellement la radio, sélectionner [Manual Tune] dans les options du menu. Utiliser le bouton « Tuning/Enter » pour régler la radio et appuyer sur le même bouton pour maintenir le réglage actuel. Enregistrer comme préréglage si nécessaire. Cela permet d'obtenir un signal plus fort dans les endroits où le signal est faible.
HQWS10001 La recherche s'arrête toujours au prochain signal reçu. Enregistrer comme préréglage si nécessaire. Réglage manuel FM Régler manuellement le mode FM à l'aide du bouton « Réglage/Enter ». Enregistrer comme préréglage si nécessaire. Cela permet d'obtenir un signal plus fort dans les endroits où le signal est faible. Options du menu FM Maintenir le bouton « lnfo/Menu » jusqu’à ce que [Scan Setting] s’affiche. Utiliser le bouton « Tuning/Enter » pour naviguer à travers les options.
HQWS10001 Option du menu AUX Maintenir enfoncé le bouton « lnfo/Menu » jusqu’à ce que « Système » s'affiche. Appuyer sur le bouton « Tuning/Enter » pour sélectionner l'option [System]. 5.6 Options du système Options du menu du système Maintenir enfoncé le bouton « lnfo/Menu » jusqu’à ce que [Scan Setting] s’affiche en mode DAB ou FM et [System] en mode AUX. Tourner le bouton « Tuning/Enter » pour naviguer à l'option [System] et appuyer sur le même bouton pour sélectionner le système.
HQWS10001 Heure/Date Cette option vous permet de régler manuellement l’heure et la date. Une fois sélectionné à partir du sous-menu [Time], l'affichage des heures clignote. Tourner le bouton « Tuning/Enter » pour naviguer à travers les heures et appuyer sur le même bouton pour sélectionner la valeur de l’heure souhaitée. Une fois les heures réglées, l'affichage des minutes à clignote. Répéter le processus cidessus et régler les minutes.
HQWS10001 Dim Cette option vous permet de régler le niveau du rétroéclairage de l'écran inactif. Faire défiler les options en tournant le bouton « Tuning/Enter » et appuyer sur le même bouton pour sélectionner : High → Med → Low L’astérisque en haut à droite indique la sélection actuelle. Veille inactive (sommeil) Cette fonction permet de mettre la radio en veille après une période d'inactivité.
HQWS10001 Rappeler un préréglage Pour rappeler un préréglage sur 1-5, appuyer l’un des numéros préréglés pour rappeler la station enregistrée. Pour rappeler un préréglage de 6-10, appuyer sur le bouton « shift » suivi par le numéro préréglé pour rappeler la station enregistrée. Noter que tous les paramètres programmés seront perdus lorsque la radio sera déconnectée du réseau ou lorsque les piles seront retirées. 5.
HQWS10001 Régler l'alarme Utiliser le bouton « Tuning/Enter » pour naviguer à travers les options disponibles et appuyer dessus pour sélectionner une option. Après avoir sélectionné l'option, la valeur suivante à définir est déplacée vers la suivante, et ainsi de suite jusqu'à ce que le processus soit terminé.
HQWS10001 7. Spécifications techniques alimentation adaptateur ......................................................................................... 5 VCC, 1 A piles .................................................................4 x pile type C de 1.5 V (non incl.) sortie de haut-parleur .............................................................................. 2 x 2.5 W indice IP .........................................................................................................
HQWS10001 MANUAL DEL USUARIO 1. Introducción A los ciudadanos de la Unión Europea Importantes informaciones sobre el medio ambiente concerniente a este producto Este símbolo en este aparato o el embalaje indica que, si tira las muestras inservibles, podrían dañar el medio ambiente. No tire este aparato (ni las pilas, si las hubiera) en la basura doméstica; debe ir a una empresa especializada en reciclaje. Devuelva este aparato a su distribuidor o a la unidad de reciclaje local.
HQWS10001 panel trasero del aparato. Para reducir el riesgo de incendios o descargas eléctricas, confíe las reparaciones solo a un servicio técnico cualificado. 3. 4. Normas generales • Véase la Garantía de servicio y calidad Velleman® al final de este manual del usuario. • Por razones de seguridad, las modificaciones no autorizadas del aparato están prohibidas. Los daños causados por modificaciones no autorizadas, no están cubiertos por la garantía.
HQWS10001 El dígito del lado derecho indicará el número de emisoras disponibles. Después de haber terminado la búsqueda, la radio sintonizará la primera emisora alfabéticamente disponible en el modo DAB. Vuelva a pulsar el botón de encendido/apagado para activar el modo de espera (standby). Desactivar el aparato Mantenga pulsado el botón de encendido/apagado hasta que el aparato se apague o pulse el botón brevemente para desactivar el modo de espera (standby). 5.
HQWS10001 Full Scan Seleccione [Full Scan] en las opciones del menú borrar completamente todas las emisoras DAB disponibles y resintonizar nuevas. La radio buscará por todos los canales disponibles. Los canales encontrados se visualizarán en orden alfabético. Sintonizar DAB de forma manual Seleccione [Manual Tune] para sintonizar la radio de forma manual. Gire el botón giratorio 'Tuning/Enter' para sintonizar la radio y púlselo luego para guardar el ajuste actual.
HQWS10001 El escaneo se para siempre en cuanto recibe la siguiente señal. Si fuera necesario, puede memorizarlo como preajuste. Sintonizar FM manualmente Gire el botón giratorio 'Tuning/Enter' para sintonizar manualmente la radio. Si fuera necesario, puede memorizarlo como preajuste. De esa manera, obtendrá una señal clara en regiones con una señal débil. Opciones del menú FM Mantenga pulsado el botón 'Info/Menu' hasta que se visualice [Scan Setting].
HQWS10001 que el volumen del aparato conectado esté en la posición máxima para que la radio pueda reproducir el sonido. Utilice el ajuste de volumen para regular el volumen. Opciones de menú AUX Mantenga pulsado el botón 'Info/Menu' hasta que se visualice [System] en la pantalla. Gire el botón giratorio 'Tuning/Enter' para seleccionar [System]. 5.
HQWS10001 Las opciones son: Time/Date → Auto Update → Set 12/24 → Date Format Hora/Fecha Con esta opción puede ajustar manualmente la hora y la fecha. Después de haber seleccionado el submenú [Time], las horas parpadearán. Gire el botón giratorio 'Tuning/Enter' para desplazarse por las horas y púlselo luego para seleccionar la hora deseada. Después de haber ajustado la hora, los minutos empezarán a parpadear. Repito los pasos mencionados arriba para ajustar los minutos.
HQWS10001 On Level Con esta opción puede ajustar el nivel de luminosidad de la pantalla activa. Gire el botón giratorio 'Tuning/Enter' para desplazarse por las opciones y púlselo luego para seleccionar uno de los siguientes valores: High → Med → Low El asterisco en la esquina superior derecha indica la selección actual. Dim Con esta opción puede ajustar el nivel de luminosidad de la pantalla inactiva.
HQWS10001 Memorizar el preajuste 1-6 Sintonice una emisora en DAB o FM y asegúrese de que está reproduciendo. Pulse el botón 'shift' y mantenga pulsado uno de los preajustes (1/6, 2/7, 3/8, 4/9 ó 5/10). Esto se refiere al segundo número mostrado. En caso de una memorización lograda, aparece el mensaje que el preajuste está memorizado. Recordar un preajuste Para recordar un preajuste de 1-5 pulse uno de los números de los preajustes para recordar la emisora memorizada.
HQWS10001 Ajustar la alarma Mantenga pulsado el botón 'Info/Menu' hasta que la pantalla cambie. Gire el botón giratorio 'Tuning/Enter' para desplazarse por el menú [System] y pulse este botón para seleccionar. Gire el botón giratorio 'Tuning/Enter' para desplazarse por el menú [Alarm] y pulse este botón para seleccionar. Advertencia: Es posible solo ajustar la alarma, si la Radio está encendida pero no está en el modo de espera.
HQWS10001 Mantenimiento • Cualquier reparación debe ser realizada por un técnico cualificado. Nunca abra el aparato. El usuario no habrá de efectuar el mantenimiento de ninguna pieza. No intente abrir ni reparar el aparato, ya que esto puede anular la garantía y/o podría causar daños al producto o lesiones personales. Almacenamiento • 7. Almacene el aparato y los accesorios en un lugar limpio y seco. Especificaciones alimentación adaptador de red ......................................................
HQWS10001 BEDIENUNGSANLEITUNG 1. Einführung An alle Einwohner der Europäischen Union Wichtige Umweltinformationen über dieses Produkt Dieses Symbol auf dem Produkt oder der Verpackung zeigt an, dass die Entsorgung dieses Produktes nach seinem Lebenszyklus der Umwelt Schaden zufügen kann. Entsorgen Sie die Einheit (oder verwendeten Batterien) nicht als unsortierter Hausmüll; die Einheit oder die verwendeten Batterien müssen von einer spezialisierten Firma zwecks Recycling entsorgt werden.
HQWS10001 • 3. 4. Manchmal müssen Netzkabel und/oder Anschlussstecker des Geräts ausgetauscht werden. Dies hängt von der bei der Installation verfügbaren Stromquelle ab. Verbinden Sie das Gerät nur mit Spannungsquellen, die auf der Geräterückseite angegeben sind. Um das Risiko von Feuer oder Stromschlag zu verringern, überlassen Sie die Wartung qualifiziertem Fachpersonal. Allgemeine Richtlinien • Siehe Velleman® Service- und Qualitätsgarantie am Ende dieser Bedienungsanleitung.
HQWS10001 Das Datum und die Uhrzeit werden automatisch über das DAB-Signal eingestellt. Das Radio sucht die verfügbaren Sender. Die Nummer auf der rechten Seite zeigt die Anzahl der verfügbaren Sender. Nach der Beendigung des Scans stellt das Radio den ersten alphabetisch gelisteten Sender, der im DAB-Modus verfügbar ist, ein. Drücken Sie den EIN/AUS-Schalter erneut, um den Standby-Modus einzuschalten.
HQWS10001 Drehen Sie den Drehknopf 'Einstellen/Eingabe', um durch die Optionen zu scrollen und drücken Sie ihn, um eine Option auszuwählen. Verfügbare Optionen: Full Scan → Manual Tune → DRC → Prune → System Full Scan (vollständiger Scan) Wählen Sie [Full Scan] in den Menüoptionen, um alle verfügbaren DAB-Sender vollständig zu löschen und neue neu einzustellen. Das Radio scannt durch alle verfügbaren Kanäle. Alle gefundenen Kanäle werden in alphabetischer Reihenfolge angezeigt.
HQWS10001 5.4 FM-Modus FM-Modus auswählen Drücken Sie die Taste 'Modus', um zwischen DAB und FM-Radio zu wechseln. FM automatisch einstellen Drücken Sie die Taste 'Scan' ein Mal, um den nächsten verfügbaren Radiosender einzustellen. Der Scan stoppt immer am nächsten empfangenen Signal. Bei Bedarf können Sie können dies als Voreinstellung speichern. FM manuell einstellen Drehen Sie den Drehknopf 'Einstellen/Eingabe', um das Radio manuell im FM-Modus einzustellen.
HQWS10001 5.5 AUX-Modus AUX-Modus wählen Um den AUX-Modus zu wählen, drücken Sie die Taste Modus bis [AUX] auf dem Display erscheint. AUX-Modus verwenden Schließen Sie ein Gerät (z.B. Smartphone, MP3-Spieler, Tablet usw.) mit einem Kabel mit 3.5-mm-Klinkenstecker an den AUX-Eingang auf der Rückseite des Radios an. Vergewissern Sie sich davon, dass die Lautstärke des angeschlossenen Gerätes auf das Maximum steht, damit der Ton durch das Radio abgespielt werden kann.
HQWS10001 * Sie können den EQ im Untermenü unter [My EQ] individualisieren: Loudness Treble Bass Y/N +/- 7 +/- 7 Drehen Sie den Drehknopf 'Einstellen/Eingabe', um durch die Optionen zu scrollen und drücken Sie ihn, um eine Option auszuwählen. Uhrzeit Alle Zeit- und Datumsfunktionen und Präferenzen können Sie hier ändern. Drehen Sie den Drehknopf 'Einstellen/Eingabe', um durch die Optionen zu scrollen und drücken Sie ihn, um eine Option auszuwählen.
HQWS10001 Drehen Sie den Drehknopf 'Einstellen/Eingabe', um durch die Optionen zu scrollen und drücken Sie ihn, um eine Option auszuwählen: Time Out → On Level → Dim Zeit aus Hier wird die Dauer eingestellt, bevor das Display erlischt. Drehen Sie den Drehknopf 'Einstellen/Eingabe', um durch die Optionen zu scrollen und drücken Sie ihn, um einen der folgenden Werte auszuwählen: On → 10 → 20 → 30 → 45 → 60 → 90 → 120 → 180 seconds Das Sternchen rechts oben zeigt die aktuelle Auswahl an.
HQWS10001 SW Ver. Hier wird die aktuelle Softwareversion angezeigt. 5.7 DAB/FM-Voreinstellung Das Radio ermöglicht es Ihnen, 10 DAB- und FM-Sender voreinzustellen. Voreinstellung 1-5 speichern Stellen Sie einen Sender entweder in DAB oder FM ein und stellen Sie sicher, dass er aktuell spielt. Halten Sie eine der Voreinstellungen (1/6, 2/7, 3/8, 4/9 oder 5/10) gedrückt. Dies bezieht sich auf die erste angezeigte Zahl.
HQWS10001 FM • • • • • • • Now Playing • • • Power Type Station Name Music Genre Mono/Stereo Power Type Time Date AUX 5.9 Time Date Alarm Alarm/Snooze deaktivieren Drücken Sie die Taste EIN/AUS, um den Alarm zu stoppen oder drücken Sie die Taste 'Snooze', um einen 5-Minuten Countdown zu starten, bevor der Alarm erneut ertönt. Alarm einstellen Halten Sie die Taste 'lnfo/Menü' gedrückt, bis sich der Bildschirm ändert.
HQWS10001 Den Alarm ein-/ausschalten Scrollen Sie durch den Prozess zur Alarmeinstellung und stellen Sie die Option 'Alarm' auf [On] oder [Off]. 6. Pflege und Wartung Reinigung • Schalten Sie das Gerät vor Beginn der Reinigungs- oder Wartungsarbeiten spannungsfrei und lassen Sie es abkühlen. • Reinigen Sie die Außenseite des Gerätes mit einem leicht mit Wasser und Seife angefeuchteten, sanften Tuch mit ein bisschen Seife und Wasser.
HQWS10001 INSTRUKCJA OBSŁUGI 1. Wstęp Dotyczy mieszkańców Unii Europejskiej. Ważne informacje dotyczące środowiska. Niniejszy symbol umieszczony na urządzeniu bądź opakowaniu wskazuje, że utylizacja produktu może być szkodliwa dla środowiska. Nie należy wyrzucać urządzenia (lub baterii) do zbiorczego pojemnika na odpady komunalne, należy je przekazać specjalistycznej firmie zajmującej się recyklingiem. Niniejsze urządzenie należy zwrócić dystrybutorowi lub lokalnej firmie świadczącej usługi recyklingu.
HQWS10001 • 3. Urządzenie może wymagać użycia innego przewodu zasilającego, wtyczki lub obu, w zależności od dostępnego źródła zasilania podczas montażu. Urządzenie należy podłączać wyłącznie do źródła zasilania wskazanego na tylnym panelu urządzenia. Aby ograniczyć ryzyko pożaru lub porażenia prądem elektrycznym, należy zlecić serwisowanie uprawnionemu personelowi serwisowemu lub o równorzędnych kwalifikacjach.
HQWS10001 Sygnał DAB ustawi automatycznie datę i godzinę. Radio rozpocznie skanowanie w celu znalezienia dostępnych częstotliwości. Cyfra po prawej stronie wskazuje liczbę dostępnych częstotliwości. Po zakończeniu skanowania radio dostroi się do pierwszej stacji z alfabetycznej listy dostępnej w trybie DAB. Nacisnąć ponownie przycisk on-off, aby przełączyć urządzenie w tryb czuwania.
HQWS10001 Obrócić pokrętło Tuning/Enter, aby przejrzeć dostępne opcje i nacisnąć pokrętło, aby wybrać. Dostępne opcje: Full Scan → Manual Tune → DRC → Prune → System Pełny skan [Full Scan] Wybierz [Full Scan] w menu opcji, aby całkowicie usunąć i na nowo dostroić wszystkie dostępne stacje DAB. Radio rozpocznie skanowanie dostępnych kanałów. Wszystkie kanały będą wyświetlane w kolejności alfabetycznej. Ręczne strojenie DAB [Manual Tune] Wybrać [Manual Tune], żeby ręcznie nastroić radio.
HQWS10001 5.4 Tryb FM Wybór trybu FM Nacisnąć przycisk trybu, aby zmienić DAB na radio FM. Automatyczne strojenie FM Aby automatycznie wybrać kolejną dostępną stację, wystarczy nacisnąć raz przycisk Scan. Skanowanie zatrzyma się po wykryciu kolejnego dostępnego sygnału. W razie potrzeby zachować jako zaprogramowane ustawienie. Ręczne strojenie FM Nastroić ręcznie radio w trybie FM pokrętłem Tuning/Enter. W razie potrzeby zachować jako zaprogramowane ustawienie.
HQWS10001 5.5 Tryb Aux Wybór trybu AUX Aby wybrać tryb AUX, należy naciskać przycisk Mode aż do wyświetlenia się napisu [AUX]. Używanie trybu AUX Przy użyciu kabla jack 3,5 połączyć urządzenie (telefon, odtwarzacz MP3, tablet...) z portem AUX z tyłu radia. Upewnić się, że podłączone urządzenie ma ustawiony maksymalny poziom głośności, aby móc odtwarzać dźwięk przez radio. Za pomocą regulatora głośności można ustawiać poziom głośności.
HQWS10001 * EQ można regulować według własnych potrzeb, korzystając z podmenu w zakładce [My EQ]: Głośność Tony wysokie Tony niskie Y/N +/- 7 +/- 7 Pokrętłem Tuning/Enter przejrzeć dostępne opcje i nacisnąć, aby wybrać. Czas W tym miejscu można zmienić wszelkie funkcje i preferencje godziny i daty. Obrócić pokrętło Tuning/Enter, aby przejrzeć dostępne opcje i nacisnąć pokrętło, aby wybrać.
HQWS10001 Obrócić pokrętło Tuning/Enter, aby przejrzeć dostępne opcje i nacisnąć to samo pokrętło, aby wybrać jedną z opcji: Time Out → On Level → Dim Time Out Opcja ta umożliwia ustalenie czasu przed wygaszeniem wyświetlacza. Przejrzeć opcje, obracając pokrętło Tuning/Enter i nacisnąć to samo pokrętło, aby wybrać. On → 10 → 20 → 30 → 45 → 60 → 90 → 120 → 180 sekund Gwiazdka w prawym górnym rogu oznacza aktualny wybór. On Level Opcja ta umożliwia ustawienie poziomu podświetlenia aktywnego wyświetlacza.
HQWS10001 5.7 DAB/FM Preset Radio ma 10 zaprogramowanych przycisków dla DAB i FM. Zapisywanie ustawień 1-5 Wybrać stację DAB lub FM i upewnić się, że jest aktualnie odtwarzana. Nacisnąć i przytrzymać jeden z przycisków ustawień oznaczony 1/6, 2/7, 3/8, 4/9 lub 5/10. Dotyczy to pierwszego wyświetlonego numeru. Po pomyślnym zakończeniu operacji na wyświetlaczu pojawi się komunikat o zapisaniu ustawienia. Zapisywanie ustawień 1-6 Wybrać stację DAB lub FM i upewnić się, że jest aktualnie odtwarzana.
HQWS10001 FM • • • • • • • Teraz odtwarzane • • • Rodzaj zasilania Nazwa stacji Gatunek muzyczny Mono/Stereo Rodzaj zasilania Czas Data (DATE) AUX 5.9 Czas Data (DATE) Alarm Wyłączenie alarmu/Drzemka Nacisnąć przycisk On-Off, aby wyłączyć alarm lub nacisnąć przycisk drzemki Snooze, aby rozpocząć 5-minutowe odliczanie przed ponownym włączeniem alarmu. Ustawianie alarmu Nacisnąć i przytrzymać przycisk Info/Menu aż do zmian na wyświetlaczu.
HQWS10001 Włączanie/wyłączanie alarmu Ustawić alarm zgodnie z instrukcją i zmienić opcję [Alarm] na [On] lub [Off]. 6. Utrzymanie i konserwacja Czyszczące • Przed rozpoczęciem jakichkolwiek prac związanych z czyszczeniem lub konserwacją odłączyć urządzenie od źródła zasilania i pozostawić do schłodzenia. • Przetrzeć powierzchnie zewnętrzne urządzenia miękką szmatką zwilżoną mydłem i roztworem wodnym. Nie zanurzać urządzenia w wodzie ani innej cieczy.
HQWS10001 MANUAL DO UTILIZADOR 1. Introdução Aos cidadãos da União Europeia Importantes informações sobre o meio ambiente no que respeita a este produto Este símbolo no aparelho ou na embalagem indica que, enquanto desperdícios, poderão causar danos no meio ambiente. Não coloque a unidade (ou as pilhas) no depósito de lixo municipal; deve dirigir-se a uma empresa especializada em reciclagem. Devolva o aparelho ao seu distribuidor ou ao posto de reciclagem local.
HQWS10001 este aparelho apenas à fonte de alimentação indicada no painel traseiro do aparelho. Para reduzir o risco de incêndio ou choque elétrico, recorra sempre à assistência técnica, a pessoal devidamente qualificado ou equivalente. 3. 4. Normas gerais • Consulte a Garantia de Serviço e Qualidade Velleman ® na parte final deste manual do utilizador. • Por razões de segurança, estão proibidas quaisquer modificações do aparelho desde que não autorizadas.
HQWS10001 O dígito à direita indica a quantidade de frequências disponíveis. Assim que a busca estiver concluída, o rádio ficará sintonizado na primeira estação, listada alfabeticamente, e disponível no modo DAB. Pressione o botão de ligar-desligar novamente para colocar o aparelho no modo de espera (standby). Desligar Mantenha o botão de ligar-desligar pressionado até que o aparelho desligue, ou pressione o botão brevemente para cancelar o modo de espera. 5.
HQWS10001 O rádio fará a busca através de todos os canais disponíveis. Todos os canais serão exibidos por ordem alfabética. Sintonização DAB Manual Selecione [Manual Tune] para sintonizar o rádio manualmente. Use o seletor "tuning/enter" para sintonizar o rádio e pressione o mesmo para guardar a sintonização. Salvar como uma predefinição, se necessário. Isto ajuda a obter um sinal mais nítido em áreas em que o sinal é mais fraco.
HQWS10001 Sintonização FM Manual Use o seletor "tuning/enter" para sintonizar manualmente o rádio no modo FM. Salvar como uma predefinição, se necessário. Isto ajuda a obter um sinal mais nítido em áreas em que o sinal é mais fraco. Opções do Menu FM Mantenha o botão info/menu pressionado até aparecer [Scan Setting]. Use o seletor "tuning/enter" para visualizar as opções. Depois, pressione o seletor para selecionar uma determinada opção.
HQWS10001 Opção de Menu AUX Mantenha o botão info/menu pressionado até aparecer [System]. Pressione o seletor "tuning/enter" para selecionar a opção [System] 5.6 Opções de Sistema Opções do Menu Sistema Mantenha o botão info/menu pressionado até aparecer [Scan Setting], tanto no modo DAB como FM, ou [System] no modo AUX. Rode o seletor "tuning/enter" para selecionar a opção [System] e pressione o seletor para confirmar.
HQWS10001 Hora/Data Esta opção permite-lhe acertar a hora e data manualmente. Feita a seleção através do submenu [Time], verá as horas ficarem intermitentes. Rode o seletor "tuning/enter" para se deslocar pelas horas e pressione o mesmo seletor para selecionar a hora correta. Assim que acertar a hora, os minutos ficam intermitentes. Repita o processo acima e acerte os minutos. Após seleção, continuará para o ecrã seguinte para acertar a data.
HQWS10001 Dim Esta opção permite definir o nível de luz do visor quando inativo. Escolha uma das opções rodando o seletor "tuning/enter" e pressione o mesmo seletor para selecionar uma opção: High → Med → Low O asterísco no canto superior direito indica a opção selecionada atualmente. Inactive Standby (Step) Pode definir o tempo de espera automática através desta função.
HQWS10001 Recuperar uma Predefinição Para recuperar uma predefinição de 1 a 5, pressione um dos números predefinidos para aceder à estação guardada. Para recuperar uma predefinição de 6 a 10, pressione o botão de mudança seguido de um dos números predefinidos para aceder à estação guardada. Tenha em conta que todas as predefinições serão perdidas assim que o rádio for desligado da rede elétrica ou se as pilhas forem removidas. 5.
HQWS10001 Configurar o Alarme Aceda à opção usando o seletor "tuning/enter" e pressione o seletor para o selecionar o menu. Depois de uma opção ser selecionada, passa-se para o próximo valor a ser definido até que todo o processo esteja concluído.
HQWS10001 7. Especificações alimentação adaptador .......................................................................................... 5 VDC, 1 A pilhas ....................................................................... 4 x 1.5 V C botão (não incl.) saída para alto-falante ............................................................................. 2 x 2.5 W classificação IP ................................................................................................IPX3 frequência FM .....
Velleman® Service and Quality Warranty Since its foundation in 1972, Velleman® acquired extensive experience in the electronics world and currently distributes its products in over 85 countries. All our products fulfil strict quality requirements and legal stipulations in the EU. In order to ensure the quality, our products regularly go through an extra quality check, both by an internal quality department and by specialized external organisations.
- tout dommage à cause d’une utilisation commerciale, professionnelle ou collective de l’appareil (la période de garantie sera réduite à 6 mois lors d’une utilisation professionnelle) ; - tout dommage à l’appareil qui résulte d’une utilisation incorrecte ou différente que celle pour laquelle il a été initialement prévu comme décrit dans la notice ; - tout dommage engendré par un retour de l’appareil emballé dans un conditionnement non ou insuffisamment protégé.
Velleman ® usługi i gwarancja jakości Od czasu założenia w 1972, Velleman® zdobył bogate doświadczenie w dziedzinie światowej elektroniki. Obecnie firma dystrybuuje swoje produkty w ponad 85 krajach. Wszystkie nasze produkty spełniają surowe wymagania jakościowe oraz wypełniają normy i dyrektywy obowiązujące w krajach UE.