Total solder points: 63 Difficulty level: beginner 1 2 3 4 5 advanced 2 CHANNEL RF CODELOCK TRANSMITTER K8059 /VM109 h K8057 iver it w e s u ce For el RF re 2 Chann ILLUSTRATED ASSEMBLY MANUAL H8059IP-1 1
Features & Specifications Features: For use with the K8057/VM109 2-channel RF receivers. Generates unique 32-bit code. More than 1,000,000,000 unique codes. Code can easily be changed for safety purposes. Choose continuous or 'burst' transmission. LED indicator. Limited compatibility with K6706 - K6706A - K6706B/G Specifications: Power supply: 12V battery V23GA, GP23GA,... (not incl.) 433MHz operation Open field range of up to 30m possible Dimensions: 63 x 40 x 16mm (2.5" x 1.6" x 0.
Assembly hints 1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools: • A good quality soldering iron (25-40W) with a small tip. • Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will protect the tip, and enables you to make good connections.
Assembly hints 1.3 Soldering Hints : 1- Mount the component against the PCB surface and carefully solder the leads 2- Make sure the solder joints are cone-shaped and shiny 3- Trim excess leads as close as possible to the solder joint REMOVE THEM FROM THE TAPE ONE AT A TIME ! AXIAL COMPONENTS ARE TAPED IN THE CORRECT MOUNTING SEQUENCE ! You will find the colour code for the resistances and the LEDs in the HALG (general manual) and on our website: http://www.velleman.be/common/service.
Construction 1. Diodes. Watch the polarity! 3. 1/8W Resistors 5. Push buttons R... CATHODE D... D1 : BAT85 D2 : BAT85 2. Zenerdiode. Watch the polarity! R1 R2 R3 R4 R5 R6 : : : : : : 33K 33K 33K 47 220 2K7 (3 - 3 - 3 - B) (3 - 3 - 3 - B) (3 - 3 - 3 - B) (4 - 7 - 0 - B) (2 - 2 - 1 - B) (2 - 7 - 2 - B) SW1 : KRS0611 SW2 : KRS0611 SW3 : KRS0611 6. IC socket. Pay attention to the position of the notch! 4. SAW resonator CATHODE ZD... X1 : SAW433 X...
Construction 7. Battery contacts + - 9. Capacitors 11. IC. Pay attention to the notch ! + IC1 : VK8059 C1 : 1pF (red 1) C2 : 4p7 (black, 4.7) C3 : 100pF (101) Bend C3 away from the IR-LED Check for good attachment of the solder to the contacts C4 : 100pF C5 : 100pF C6 : 100nF (101) (101) (104) 10. Transistor 8. LED VK8059=(Programmed PIC12F629) Pay attention to the position of the notch! 12. Sticker Affix the supplied sticker to the back of the housing. Velleman COLOR= 2...
Use 13. Use The transmitter comes with a factory set default code. However, for security reasons, it might be wise not to use the default code. 1. To program your unique code : Hold SW1(*) (left button). Briefly press the 'program'-button (SW3) 3 times. The LED will flash 3 times. Release SW1. Your unique 32-bit code has been generated and stored.
3.
Schematic diagram 14. Schematic diagram. R6 2K7-1/8W R4 47-1/8W R3 33K-1/8W LD1 LED3RL 6 5 L C3 C1 MPSH10 T1 100p 1p 12V 4p7 R2 R1 33K-1/8W X1 C2 BAT1 4 33K-1/8W R5 220-1/8W 3 2 SW3 C4 J1 GP0/CIN+/ICSPDAT GP1/CIN-/ICSPCLK GP2/T0CKl/INT/COUT GP4/T1G/OSC2/CLKOUT GP5/T1CKI/OSC1/CLKIN J2 Vss 8 SAW433 SW KRS0611 D2 BAT85 D1 BAT85 C5 SW1 SW2 100p SW KRS0611 10 SW KRS0611 C6 ZD1 100n 5V1/0.
PCB 15.
VELLEMAN Components NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com Modifications and typographical errors reserved © Velleman Components nv.