Datasheet

ManualsBrandsVELLEMAN ManualsArduinoI/O SHIELD FOR ARDUINO®

ILLUSTRATED ASSEMBLY MANUAL HKA05P’1

STR

STRA

STR

STRA

STR

STRA

TED

ASS

ASSE

ASS

SSE

MBLY

BLY

MBLY

MAN

UAL

HKA0

HKA

HKA0

5P’1

KA05

IN/OUT shield

for Arduino

General purpose INPUT - OUTPUT shield for Arduino

Features

• For use with Arduino Due™, Arduino 8QR™, Arduino 0ega™

• 6 analog inputs

• 6 digital input

• 6 relay contact outputs

• Indicator leds for relay outputs and digital inputs

Speci¿ cations

• Analog inputs: 0..+5VDC

• Digital inputs: dry contact or open collector

• Relays: 12V

• Relay contacts: NO/NC 24VDC/1A max.

• Dimensions: 68 x 53mm / 2.67 x 2.08”

Summary of content (12 pages)

PAGE 1
IN/OUT shield for Arduino® ILLUSTRATED LUSTR ST STRATED STRA T TE TE TED ED D ASS AS ASSE ASSEMBLY SSEMBLY SS SSEMBLY SSE MBLY BL MAN M MANUAL ANU ANUAL UAL UA A HKA0 HKA HKA05 HKA05P’1 KA 5P’1 5P KA05 Speci¿cations • Analog inputs: 0..+5VDC • Digital inputs: dry contact or open collector • Relays: 12V • Relay contacts: NO/NC 24VDC/1A max. • Dimensions: 68 x 53mm / 2.67 x 2.
PAGE 2
Participate our Velleman Projects Forum Forum Subscribing our newsletter?, visit www.vellemanprojects.
PAGE 3
Velleman N.V.
PAGE 4
1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 3. Trim excess leads as close as possible to the solder joint 2. Make sure the solder joints are cone-shaped and shiny -4- 1. Mount the component against the PCB surface and carefully solder the leads 1.3 Soldering Hints : * Typographical inaccuracies excluded.
PAGE 5
DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE.
PAGE 6
D1 : 1N4148 D2 : 1N4148 D3 : 1N4148 D4 : 1N4148 2 Diodes D5 : 1N4148 D6 : 1N4148 D7 : 1N4148 D8 : 1N4148 D9 : 1N4148 D10: 1N4148 D11: 1N4148 D12: 1N4148 Watch the polarity! C2: 100nF (104) c... 1 Ceramic capacitor I CONSTRUCTION Construction . c..
PAGE 7
R13: R14: R15: R16: R17: R18: R19: R20: R21: R22: R23: R24: R25: R26: R27: R28: R29: R30: 4K7 10K 4K7 10K 4K7 10K 470 470 470 470 470 470 4K7 4K7 4K7 4K7 4K7 4K7 (4 - 7 - 2 - B) (1 - 0 - 3 - B) (4 - 7 - 2 - B) (1 - 0 - 3 - B) (4 - 7 - 2 - B) (1 - 0 - 3 - B) (4 - 7 - 1 - B) (4 - 7 - 1 - B) (4 - 7 - 1 - B) (4 - 7 - 1 - B) (4 - 7 - 1 - B) (4 - 7 - 1 - B) (4 - 7 - 2 - B) (4 - 7 - 2 - B) (4 - 7 - 2 - B) (4 - 7 - 2 - B) (4 - 7 - 2 - B) (4 - 7 - 2 - B) 6 x 2p (OUTPUTS) 8 x 2p (INPUTS) 7 Terminal blocks
PAGE 8
MAX. 24VDC / 1A 1 OUTPUT ANALOG 3 ANALOG INPUTS 0 ... 5V ... 101011101011001... 2 DIGITAL INPUTS -8- DOWNLOAD SAMPLE CODE FROM KA05 PAGE ON WWW.VELLEMAN.BE 6 RELAY OUTPUTS (Max.
PAGE 9
8 4K7 R9 4K7 R7 8 9 10 11 12 13 AREF 0 1 2 3 4 5 6 7 R8 10K R10 10K LD2 LED3RL GND R2 1K 1 2 3 4 5 6 SK3 T2 BC547 D8 1N4148 GND Vin GND T1 BC547 D7 1N4148 GND Vin - 1 2 3 4 5 6 ARDUINO UNO SK4 LD1 LED3RL GND R1 1K 1 2 3 4 5 6 7 8 SK2 1 2 3 4 5 6 7 8 SK1 GND C2 100n GND RY2 RELAY TSC112D3H RY1 RELAY TSC112D3H 5V 3V3 RST Vin A5 A4 A3 A2 A1 A0 Vin 3 2 1 SK6 3 2 1 SK5 11 10 DI6 DI5 DI4 DI3 DI2 DI1 C1 100/16-25V 4K7 R13 4K7 R11 1N4148 1N4148 D6 1N4
PAGE 10
PCB - 10 -
PAGE 11
= 1460 ohm = series resistance (ohms) 0.005A 9V - (3 x1.7V) required current (A) = series resistance (ohms) = 780 ohm Supply voltage (V) - (number of leds x led voltage (V)) Example: 3 x red led (1.7V) on 9V battery Required led current for full brightness: 5mA (this can be found in the datasheet of the led) LEDs in series: (9V - 1.7V) x 0.005A = 0.036W Required resistor power handling= voltage over resistor x current passed trough resistor 0.005A 9V - 1.
PAGE 12
Modi¿cations and typographical errors reserved - © Velleman nv. HKA05’IP Velleman NV, Legen Heirweg 33 - 9890 Gavere. The new Velleman Projects catalogue is now available. Download your copy here: www.vellemanprojects.