Owner's manual

ManualsBrandsVelleman ManualsToysKNS1

KNS1 - 1 - VELLEMAN

KNS1 – TYRANNOMECH

1. Introduction & Characteristics

Dispose of this product in accordance with local and national disposal regulations.

Thank you for buying the KNS1! Read this manual carefully before bringing the KNS1 into use.

• Easy to build, no glue or soldering required.

• Dislodge pre-cut pieces when you need them ; not before! Sand any jagged edges before use (sandpaper included)

• The kit is powered by 2 AA-batteries (not included).

The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a

battery holder and all necessary parts.

2. Parts List

Part n° Quant.

Description Part n°

Quant. Description

1 1 gearbox 16 1 battery holder

2 1 motor 3Vdc 17 1 slide switch with wire

3 1 pinion gear 8T 18 2 wire (7cm)

4 1 gear 40T/0T (white) 19 2 nut M2

5 1 gear 40T/10T (red) 20 28 self-tapping screw (2 x 4mm)

6 1 gear 40T/10T (green) 21 4 self-tapping screw

7 1 face gear 36T/10T (white) 22 2 screw

8 1 metal shaft (3 x 52mm) 23 6 washer

9 1 metal shaft (2 x 40mm) 24 2 spring

10 2 nylon post (small) 25 3 PVC tube (15mm)

11 2 nylon pad 26 2 metal foot (U-shaped)

12 4 nylon post (large) 27 6 fixing plate (large)

13 6 nylon pad (Ø8mm) 28 2 fixing plate (small)

14 1 wire with terminal (yellow) 29 2 nylon connector

15 1 wire with terminal (green)

Fig.1

Summary of content (9 pages)

PAGE 1
KNS1 – TYRANNOMECH 1. Introduction & Characteristics Dispose of this product in accordance with local and national disposal regulations. Thank you for buying the KNS1! Read this manual carefully before bringing the KNS1 into use. • Easy to build, no glue or soldering required. • Dislodge pre-cut pieces when you need them ; not before! Sand any jagged edges before use (sandpaper included) • The kit is powered by 2 AA-batteries (not included).
PAGE 2
3. Prepunched Boards Fig.2 4. Assembly Fig.3 The gears (P4-7) should be placed to the left of the pinion gear. One N-shaped nylon connector (P29) should point downward and the other one upward. Insert the motor as shown in the drawing. Note that the protruding side should point towards the metal case. Fig.4 Screw 2 fixing plates (P27/28) to board edges A1 & A2 and screw them to board X BEFORE fitting the gearbox. Fig.
PAGE 3
Fig.6 Use an “L”-fixing plate (P27) to connect boards R and X. Fig.7 Slide board S onto board X and screw switch P17 onto board S. Use 1 fixing plate P27 to fix boards S and X. Insert one wire in the PVC tube (P25), twist the two wires and cover the joint with the PVC tube. Make sure the wiring is correct !!! 1. green 2. red 3. yellow 4. red 5. black Fig.8 Fig.9 Screw a fixing plate P27 to boards Y and Z first and then attach them to boards B and C.
PAGE 4
Fig.10 Mount the right (T) and left (U) arms to the Y/Z assembly. Fig.11 Mount the arms to board S and use the wire (n°18) to connect Tyrannomech’s arms and legs. Fig.12 Fix all remaining boards in their indicated positions. The specifications and contents of this manual can be subject to change without prior notice. KNS1 – TYRANNOMECH 1. Inleiding en Kenmerken Ontdoe u van dit product volgens de plaatselijke en nationale regelgeving inzake verwijdering.
PAGE 5
2. Lijst van Onderdelen Nr. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Hoev. 1 1 1 1 1 1 1 1 1 2 2 4 6 1 1 Beschrijving tandwielkast motor 3Vdc rondsel 8T tandwiel 40T/0T (wit) tandwiel 40T/10T (rood) tandwiel 40T/10T (groen) tandwiel 36T/10T (wit) metalen as (3 x 52mm) metalen as (2 x 40mm) nylon ring (klein) nylon kraagring nylon ring (groot) nylon kraagring (Ø8mm) draad met connector (geel) draad met connector (groen) Nr. 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Hoev.
PAGE 6
KNS1 – TYRANNOMECH 1. Introduction et Caractéristiques Débarrassez-vous de ce produit en respectant la législation d'élimination locale et nationale. Nous vous remercions de votre achat ! Lisez la notice présente attentivement avant la mise en service du KNS1. • Facile à assembler, sans colle ou soudage. • Ne détachez les pièces prédécoupées qu’au moment où vous en avez besoin.
PAGE 7
Fig. 7: Mettez panneau S sur panneau X et vissez commutateur P17 sur panneau S. Fixez panneaux S et X avec 1 crochet de fixation P27. Fig. 8: Insérez 1 fil dans le tube en PVC (P25), tressez les deux fils et recouvrez le joint à l’aide du tube. Veillez à ce que le câblage soit correctement connecté!!! 1. vert - 2. rouge - 3. jaune - 4. rouge - 5. noir Fig. 9: Vissez d’abord un crochet de fixation (P27) aux panneaux Y et Z et vissez-les sur les panneaux B et C. Fig.
PAGE 8
3. Piezas precortadas (véase fig.2 en la p.2) 4. Montaje (véase p.2-4 para las figuras) Fig. 3: Coloque los piñones (P4-7) a la izquierda del satélite. Apunte el primer conector ”N” de nylon (P29) hacia abajo y el otro hacia arriba. Instale el motor según la figura. Preste atención a que el saliente apunte hacia la caja metálica. Fig. 4: Atornille 2 ganchos de fijación (P27/28) en los paneles A1 y A2 y fíjelos a los paneles X ANTES de montar la caja de engranajes. Fig.
PAGE 9
2. Stückliste Nr. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 St. 1 1 1 1 1 1 1 1 1 2 2 4 6 1 1 Beschreibung Getriebe Motor 3Vdc Ritzel 8T Zahnrad 40T/0T (weiß) Zahnrad 40T/10T (rot) Zahnrad 40T/10T (grün) Zahnrad 36T/10T (weiß) Metallachse (3 x 52mm) Metallachse (2 x 40mm) Nylonring (klein) Nylonanschluss Nylonring (groß) Nylonanschluss (Ø8mm) Draht mit Anschluss (gelb) Draht mit Anschluss (grün) Nr. 16 17 18 19 20 21 22 23 24 25 26 27 28 29 St.