Specifications

ManualsBrandsVelleman ManualsToysKNS2

KNS2 – STEGOMECH

1. Introduction & Characteristics

Dispose of this product in accordance with Local and national disposal regulations.

Thank you for buying the KNS2! Read this manual carefully before bringing the device into use.

• Easy to build, no glue or soldering required.

• Dislodge pre-cut pieces when you need them, not before. Sand any jagged edges before use (sandpaper included)

• The kit is powered by 2 AA-batteries (not included).

The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a

battery holder and all necessary parts.

2. Parts List

Part n° Quant. Description Part n° Quant. Description

1 1 gearbox 15 1 wire with terminal (yellow)

2 1 motor 3Vdc 16 1 wire with terminal (green)

3 1 pinion gear 8T 17 1 battery holder

4 1 gear 40T/0T (white) 18 1 slide switch with wire

5 1 gear 40T/10T (red) 19 20 self-tapping screw (2 x 4mm)

6 1 gear 40T/10T (green) 20 4 self-tapping screw (2 x 6mm)

7 1 face gear 36T/10T (white) 21 2 rivet (17.5mm)

8 1 metal shaft (3 x 52mm) 22 2 rivet (20mm)

9 1 metal shaft (2 x 40mm) 23 2 rivet (23mm)

10 2 nylon post (small) 24 6 washer

11 2 nylon pad 25 3 PVC tube (15mm)

12 2 nylon connector 26 4 fixing plate (large)

13 12 nylon pad (Ø8mm) 27 2 fixing plate (small)

14 6 nylon cap

KNS2 - 1 - VELLEMAN

Summary of content (9 pages)

PAGE 1
KNS2 – STEGOMECH 1. Introduction & Characteristics Dispose of this product in accordance with Local and national disposal regulations. Thank you for buying the KNS2! Read this manual carefully before bringing the device into use. • Easy to build, no glue or soldering required. • Dislodge pre-cut pieces when you need them, not before. Sand any jagged edges before use (sandpaper included) • The kit is powered by 2 AA-batteries (not included).
PAGE 2
3. Prepunched Boards Fig.2 4. Assembly Fig.3 The gears (P4-7) should be placed to the left of the pinion gear (P3). Put one N-shaped nylon connector (P12) downward and the other one upward. Insert the motor according to the drawing’s direction. Note that the protruding edge should point towards the metal case. Fig.4 Mount switch P18 to side board W28. Screw fixing plates P26 and P27 to side boards W28 & W29, then fix them to board W27. Mount the gearbox on top of board W27.
PAGE 3
Fig.5 Mount the left (W30/32/34) and right (W31/33/35) legs to the sides of board W27 as in the figure. Fig.6 Mount boards W36 and W37 to board W27 and attach boards W36 & W37 by means of fixation board W38 and 2 screws P20. Fig.7 Attach boards W36 and W37 to the bottom of board W37 by means of mounting plates P26 and screws P19. Attach the battery holder (P17) to the bottom of board W27. Connect the wiring according to this diagram.
PAGE 4
Fig.9 Fig.10 Fig. 9-12: Mount the remaining pieces according to the drawings. Fig.11 Fig.12 The specifications and contents of this manual can be subject to change without prior notice. KNS2 – STEGOMECH 1.Inleiding & kenmerken Ontdoe u van dit product volgens de plaatselijke en nationale regelgeving inzake verwijdering. Dank u voor uw aankoop! Lees deze handleiding aandachtig voor u het toestel in gebruik neemt. • Makkelijk te bouwen, zonder lijm of solderen.
PAGE 5
2. Lijst van onderdelen (zie fig.1 blz.1) Nr. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Hoev. 1 1 1 1 1 1 1 1 1 2 2 2 12 6 Beschrijving tandwielkast motor 3Vdc rondsel 8T tandwiel 40T/0T (wit) tandwiel 40T/10T (rood) tandwiel 40T/10T (groen) tandwiel 36T/10T (wit) metalen as (3 x 52mm) metalen as (2 x 40mm) nylon ring (klein) nylon kraagring nylon connector nylon kraagring (Ø8mm) nylon hoedje Nr. 15 16 17 18 19 20 21 22 23 24 25 26 27 Hoev.
PAGE 6
KNS2 – STEGOMECH 1. Introduction et Caractéristiques Débarrassez-vous de ce produit en respectant la législation d'élimination locale et nationale. Nous vous remercions de votre achat ! Lisez la notice présente attentivement avant la mise en service du KNS2. • Facile à assembler, sans colle ou soudage. • Ne détachez les pièces prédécoupées qu’au moment où vous en avez besoin.
PAGE 7
Fig. 7: Connectez les panneaux W36 et W37 au fond du panneau W27 au moyen de panneaux de fixation P26 et de vis P19. Vissez le porte-piles (P17) au fond du panneau W27. Fig. 8: Connectez le câblage selon la figure. Insérez 1 fil dans le tube en PVC (P25), tressez les deux fils et recouvrez le joint à l’aide du tube. Veillez à ce que le câblage soit correctement connecté!!! 1. vert - 2. rouge - 3. jaune - 4. rouge - 5. noir Fig. 9-12: Montez les pièces restantes selon les figures à la p. 4.
PAGE 8
4. Montaje (véase fig.3-12 p.2-4) Fig. 3: Coloque los piñones (P4-7) a la izquierda del satélite (P3). Apunte el primer conector ”N” de nylon (P12) hacia abajo y el otro hacia arriba. Instale el motor según la figura. Preste atención a que el saliente apunte hacia la caja metálica. Fig. 4: Monte el interruptor P18 en el panel lateral W28. Atornille de los paneles de fijación P26 y P27 en los paneles laterales W28 & W29 y fíjelos al panel W27. Monte la caja de engranajes en el panel W27. Fig.
PAGE 9
2. Stückliste (siehe Abb. 1 Seite 1) Nr. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 St. 1 1 1 1 1 1 1 1 1 2 2 2 12 6 Beschreibung Getriebe Motor 3Vdc Ritzel 8T Zahnrad 40T/0T (weiß) Zahnrad 40T/10T (rot Zahnrad 40T/10T (grün) Zahnrad 36T/10T (weiß) Metallachse (3 x 52mm) Metallachse (2 x 40mm) Nylonring (klein) Nylonbuchse Nylonanschluss Nylonbuchse (Ø8mm) Nylonkappe Nr. 15 16 17 18 19 20 21 22 23 24 25 26 27 St.