Owner manual

ManualsBrandsVelleman ManualsToysKNS3

KNS3 - 1 - VELLEMAN

KNS3 – ROBOMECH

1. Introduction & Characteristics

Dispose of this product in accordance with Local and National Disposal Regulations.

Thank you for buying the KNS3 ! Read this manual carefully before bringing the device into use.

• Easy to build, no glue or soldering required.

• Dislodge pre-cut pieces when you need them, not before. Sand any jagged edges before use (sandpaper included).

• The kit is powered by 2 AA-batteries (not included).

The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a

battery holder and all necessary parts.

2. Parts List

Part n° Quant.

Description Part n°

Quant. Description

1 1 gearbox 16 18 self-tapping screw (2 x 4mm)

2 1 motor 3Vdc 17 2 self-tapping screw (3 x 16mm)

3 1 pinion gear 8T 18 2 screw

4 1 gear 40T/0T (white) 19 2 rivet

5 1 gear 40T/10T (red) 20 2 nylon cap

6 1 gear 40T/10T (green) 21 2 LED with wires

7 1 face gear 36T/10T (white) 22 1 wire with terminal (yellow)

8 1 metal shaft (3 x 52mm) 23 1 wire with terminal (green)

9 1 metal shaft (2 x 40mm) 24 1 battery holder

10 2 nylon pad 25 1 slide switch with wire

11 2 nylon post (H : 3mm) 26 1 PVC tube (small)

12 2 nylon connector 27 2 PVC tube (large)

13 8 nylon pad Ø8mm 28 2 metal foot (U-shaped)

14 6 washer 29 2 fixing plate (large)

15 2 nut M2 30 1 fixing plate (small)

Fig.1

Summary of content (9 pages)

PAGE 1
KNS3 – ROBOMECH 1. Introduction & Characteristics Dispose of this product in accordance with Local and National Disposal Regulations. Thank you for buying the KNS3 ! Read this manual carefully before bringing the device into use. • Easy to build, no glue or soldering required. • Dislodge pre-cut pieces when you need them, not before. Sand any jagged edges before use (sandpaper included). • The kit is powered by 2 AA-batteries (not included).
PAGE 2
3. Prepunched Boards Fig.2 4. Assembly Fig.3 The gears (P4-7) should be placed to the left of the pinion gear (P3). Put one N-shaped nylon connector (P12) downward and another one upward. Note that the protruding edge should point towards the metal case. Fig.4 Screw a fixing plate P29 to boards B and C and fix them to board A. Then screw the gearbox onto board A.
PAGE 3
Fig.5 Assemble the right arm (G) and leg (E) and the left arm (F) and leg (D) and fix them to the gearbox assembly. Mount the switch P25 onto board A. Fig.6 Mount the head (boards H – I – J – K – L – M), insert the 2 LEDs (P21) and fix the head to the body with a P30 fixing plate and P16 screws. Fig.7 Screw the battery holder (P24) to the back of the robot. Fig.8 Fig.9 Connect the wires as in the diagram. Insert one wire in the PVC tube (P26), twist the two wires and cover the joint with the PVC tube.
PAGE 4
Fig.10 Mount the metal feet (P28) to the right and left legs with P16 screws. 5. Troubleshooting • Keep the pins of the LED well clear of each other to avoid a short circuit. • The robot may keel over sometimes. Bend the hinge of the metal feet toward the ground if this happens. Verify whether the feet are 100% horizontal. The specifications and contents of this manual can be subject to change without prior notice. KNS3 – ROBOMECH 1.
PAGE 5
3. Voorgesneden vormen (zie fig.2 blz.2) 4. Montage (zie fig.3-10 blz.2-4) Fig. 3: Plaats de tandwielen (P4-7) links van het rondsel (P3). Richt de ene N-vormige nylon connector (P12) naar beneden en de andere naar boven. Breng de motor aan volgens de tekening. Merk op dat de uitstekende rand naar de metalen behuizing moet worden gericht. Fig. 4: Schroef een bevestigingsplaatje P29 op platen B en C en zet deze vast op plaat A. Schroef dan de tandwielkast op plaat A. Fig.
PAGE 6
2. Liste des pièces (voir fig.1 p.1) Pièce 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Quant. Description 1 boîte d’engrenages 1 moteur 3Vcc 1 satellite 8T 1 pignon 40T/0T (blanc) 1 pignon 40T/10T (rouge) 1 pignon 40T/10T (vert) 1 engrenage roue plate 36T/10T (blanc) 1 axe métallique (3 x 52mm) 1 axe métallique (2 x 40mm) 2 canon en nylon 2 embout en nylon (H : 3mm) 2 connecteur en nylon 8 canon en nylon Ø8mm 6 rondelle de serrage 2 écrou M2 Pièce 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Quant.
PAGE 7
KNS3 – ROBOMECH 1. Introducción y Características Tire las muestras inservibles en los correspondientes depósitos de eliminación de residuos según las leyes locales y nacionales. ¡Gracias por haber comprado el KNS3! Lea cuidadosamente las instrucciones del manual antes de montarlo. • Fácil construcción, sin cola ni soldadura. • Separe las piezas precortadas sólo si las necesita. Lije los bordes dentados antes de usar la pieza (papel de lija incluido). • El kit funciona con 2 pilas AA (no incluidas).
PAGE 8
Fig. 6: Monte el interruptor P25 en el panel A. Fig. 7: Monte la cabeza. Fig. 8: Fije la cabeza al panel y consulte la descripción del cableado (véase figura 9). Fig. 9: Introduzca 1 hilo en el tubo de PVC (n°26), trence los dos hilos y cubre la junta con el tubo de PVC. Fig. 10: Fije los pies metálicos (P28) con los tornillos P28 a la patas izquierdas y derechas. 5. Solución de problemas • Evite cualquier contacto entre los polos del LED para protegerlo contra los cortocircuitos.
PAGE 9
3. Vorgeschnittene Teile (siehe Abb. 2 Seite 2) 4. Zusammenbau (siehe Abb. 3-10 Seite 2-4) Abb. 3: Stellen Sie die Zahnräder (Nr. 4-7) links vom Ritzel (Nr. 3). Richten Sie den einen N-förmigen Nylonanschluss (Nr. 12) nach unten und den anderen nach oben. Montieren Sie den Motor gemäß Abbildung. Beachten Sie, dass der herausragende Rand auf das Metallgehäuse gerichtet sein muss. Abb. 4: Schrauben Sie eine Befestigungsplatte (Nr. 29) auf Platten B und C fixieren Sie diese auf Platte A.