FREEWAVE FLASH TRIGGER LR USER MANUAL
INTRODUCTION Thank you for choosing Vello. The Vello FreeWave Flash Trigger LR is an 8-channel, extended range wireless flash trigger with digital circuitry. This device uses a powerful 2.4 GHz radio signal, maximizing your photographic potential by extending the signal strength. With an extended range of up to 600 ft. (183 meters), you can use the Vello FreeWave Flash Trigger LR confidently in nearly all photography settings.
BOX CONTENTS RFW-LR RFW-LR-R • Transmitter • Receiver • Receiver • 2x AA batteries • 4x AA batteries • 3.5 to 3.5 mm sync cable • 3.5 to 3.5 mm sync cable • 3.5 mm to 1/4" monoplug adapter 3.
FEATURES Extended Range: Up to 600 feet (183 m) Powerful 2.4 GHz signal: Reduced interference and improved wireless signal strength 8 digital channels: Avoids interference from other wireless remote controls All trigger mode: Can fire all channels at once Low-profile construction: Tilting joint reduces transmitter’s on-camera presence 4 Hot shoe and studio flash use: Compatible with most flashes Internal antenna: Embedded antenna reduces unit size Compatible with the Vello Captain TTL transmitter Ch.
COMPATIBLE DEVICES The Vello FreeWave Flash Trigger LR transmitter and receiver is compatible with most hot-shoe and lights, studio lights. The Vello FreeWave Flash Trigger LR does not transmit through-the-lens (TTL) settings; therefore, we recommend using a fully manually controlled hot-shoe flash with this device. The power output must always be set manually. Most flashes that can be operated manually are compatible, except Pentax, Sony/Minolta, and Sony MultiInterface flashes.
PRECAUTIONS • Please read and follow these instructions and keep this manual in a safe place. • There are no user-serviceable parts inside the devices. Do not attempt to disassemble or perform any unauthorized modification. • Do not operate the transmitter or receiver in the presence of flammable gas or vapors. • Do not handle with wet hands or immerse in or expose to water or rain. Failure to observe this precaution could result in fire or electric shock. 6 • Keep out of reach of children.
• Handle the units with care. • Make sure the item is intact and that there are no missing parts. • Do not use or leave the devices in conditions of extreme heat, severe cold, or high humidity. • All photos are for illustrative purposes only. • Turn off the power of the camera and studio flash before inserting or removing the remote. • Dispose of used batteries, packaging, and old devices in accordance to appropriate local environmental regulations. • Clean the unit with a soft, dry cloth.
OVERVIEW LED confirmation light Lanyard loop Channel indicator panel Channel down selector button All-channel selector button Transmitter Internal antenna Battery compartment (on back) Channel up selector button On/Off switch Test button Low-profile tilt joint Tightening ring Hot-shoe foot 8
Receiver LED confirmation light Battery compartment Channel down selector button Channel indicator panel On/Off switch Channel up selector button 3.
INSTALLING THE BATTERIES & TURNING ON THE DEVICE The Vello FreeWave Flash Trigger LR transmitter and receiver each take two AA batteries. To install the batteries, simply remove the battery compartment door on the back of each unit. With the door removed, insert the batteries using the correct polarity as displayed within the compartment. Once secured, reinstall the battery compartment doors.
SETTING THE CHANNELS The Vello FreeWave Flash Trigger LR transmitter and receiver can communicate via your choice of eight different channels. To change the channel on the transmitter or receiver, turn on the device and press the up or down channel selector button until the desired channel appears on the channel indicator panel. The transmitter can be set to trigger all of the units connected to Vello FreeWave Flash Trigger LR receivers regardless of the receivers' channel selection.
MOUNTING THE TRANSMITTER To wirelessly trigger your flash device using the Vello FreeWave Flash Trigger LR, with the camera and Flash Trigger LR powered off, mount the transmitter on the camera’s hot shoe by sliding the transmitter’s hotshoe foot into the camera’s hot-shoe mount. Turn the transmitter’s tightening ring to secure the device to the camera. Tilt the transmitter to achieve a low profile mounting. Select the desired channel on the Transmitter using the channel selector buttons.
MOUNTING THE RECEIVER Note: Make sure your flash and Flash Trigger LR are turned off before mounting. Mount the receiver to your tripod or stand via one of the two provided mounting options: 1. Threaded socket for a standard 1/4" screw mount 2. Accessory shoe (cold shoe) foot. Mounting a Hot-Shoe Flash To mount your hot-shoe flash to the receiver, slide the foot of the hot-shoe flash into the receiver’s hot-shoe mount. Secure the flash to the hot-shoe mount.
CONNECTING THE RECEIVER TO A HOT-SHOE FLASH 1. With your hot-shoe flash unit turned off, switch the flash’s locking switch to the unlock position. 6. Confirm that your camera, transmitter, receiver, and hot-shoe flash are all powered on. 2. Insert the hot-shoe flash’s hot-shoe foot into the receiver’s hot-shoe mount. 7. Fully press the shutter button on your camera to capture an image. All lights connected to receivers in the currently selected channel will fire simultaneously.
Note: We recommend using a fully manual controlled flash with this device. Since the FreeWave Flash Trigger LR does not transmit TTL settings, you will need to set the power output of your flash manually. Note: Your flash unit may enter sleep mode after a period of non-use. To turn off your flash’s sleep mode, refer to the device’s manual. Note: The FreeWave Flash Trigger LR receiver can be used with the Vello Captain TTL system when using Channel 1-4.
CONNECTING THE RECEIVER TO A STUDIO FLASH 1. Turn off the Studio light and the FreeWave Flash Trigger LR. 4. Confirm that your camera, transmitter, receiver, and studio flash are all powered on. 2. Using the included 3.5 mm sync cable, attach one end to the receiver’s flash socket and the other end to your studio flash. For flashes with a 1/4" monoplug socket, use the included 3.5 mm to 1/4" monoplug adapter. 5. Fully press the shutter release button on your camera.
SPECIFICATIONS Sync Speed 1/250s Frequency 2.4 GHz Range Channels 600 feet (183 meters) approx. 8 channels Transmitter Dimensions 1.3" × 1.9" × 4"(3.4 × 4.9 × 10.2 cm) Receiver Dimensions 1.5" × 1.9" × 3.4" (3.9 × 4.9 × 8.7 cm) Transmitter Weight 2.4 oz. (68 g) Receiver Weight 2.3 oz. (65.2 g) FCC COMPLIANCE This device complies with Part 15 of the FCC Rules.
TROUBLESHOOTING Check that channels on all communicating devices are identical. When turning on the unit, it is important to review and, if necessary, reset the channel selection. If first choice of channel does not work, try a different channel until you find one that works. If you encounter any signal interference, try changing the channel. Ensure that all connections are attached firmly and all cables are installed correctly.
ONE-YEAR LIMITED WARRANTY This Vello product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
www.vellogear.
