SET UP U S E R ’ S M A N U A L EQ-Max Remote Controlled Home Theater Subwoofers EQ-Max8 EQ-Max10 EQ-Max12 EQ-Max15
Enjoy. We here at Velodyne want to thank you for selecting our product. Get ready to experience the highest quality and amazing low-distortion bass that Velodyne is world famous for. Relax as you enhance your home entertainment experience with our easy setup instructions. Welcome . . .
1 Safety Notice 3 Congratulations 4 Installation 6 Front Panel 7 Rear Panel Connections 10 Crossovers 13 Interconnect Cables 13 Usage 16 M A I N TA I N 16 Restoring Defaults 16 Clean 16 Service 17 Troubleshoot 17 Protection Circuitry 19 Specifications 20 Warranty
SAFETY NOTICE EQ-Max User’s Manual SAFETY NOTICE Caution: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. the lightning flash with arrowhead symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
SAFETY NOTICE EQ-Max User’s Manual 12. PoWeR-CoRD PRoTeCTIoN — Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point at which they exit from the product. 13. CleANING — The product should be cleaned only as recommended by the manufacturer. 14.
CONGRATULATIONS EQ-Max User’s Manual Congratulations on your purchase of a Velodyne eq-Max subwoofer. This system represents the state-of-the-art in low frequency reproduction. Read and follow the instructions below to ensure safe and proper system operation. Note: Do not leave unit in direct sunlight or use in high humidity environments!!! Warning! To prevent fire or shock hazard, do not expose this product to rain or moisture.
INSTALLATION EQ-Max User’s Manual PrePare for installation your new Velodyne subwoofer provides for a number of installation options. Read all of the installation information below in order to determine which installation option is best for your system. Remember to perform all installation procedures with system power turned off to prevent possible damage. Placement The first step in installing your new eq-Max sub is to determine where it will be placed in the room.
INSTALLATION EQ-Max User’s Manual Inputs your new subwoofer is equipped with speaker-level and line-level inputs. Use the lINe leVel jacks when connecting your subwoofer to a pre-amp, signal processor (such as lFe out or sub out), line-level crossover, or receiver with pre-amp level outputs. When using the line level jacks, some receivers may not provide enough signal to have the unit’s auto-on feature operate properly.
FRONT PANEL EQ-Max User’s Manual 1 Remote Control Sensor 2 3 Mic Jack LED Readout MIC figure 1. eQ-Max front Panel. Following are brief descriptions of the controls and connections described in Figure 1. (1) remote Control sensor IR sensor window receives a signal from the included remote control. (2) led readout 2.5 digit, seven segment leD readout displays volume, phase and Auto-eq status. (3) miC JaCK Connector for the supplied microphone to use during the Auto-eq process.
REAR PANEL CONNECTIONS EQ-Max User’s Manual 7 6 5 4 3 1 figure 2. eQ-Max8, eQ-Max10 and eQ-Max12 rear Panel Connections.
REAR PANEL CONNECTIONS — DETAILED EXPLANATION EQ-Max User’s Manual 7 6 5 4 3 2 figure 3. eQ-MaX15 rear Panel Connections.
REAR PANEL CONNECTIONS EQ-Max User’s Manual Following are brief descriptions of the controls and connections described in Figures 3, 4 and 5. More detail of these connections can be found below: (1) speaKer leVel input terminals Connect these input terminals to the speaker output terminals of your amplifier or receiver. If you use this method of connection, when you go to the receiver speaker set up menu, make sure you select the large speaker option.
CROSSSOVERS EQ-Max User’s Manual rear Panel ConneCtions — DetaileD eXPlanation your new subwoofer is equipped with both speaker-level and line-level inputs. Use the RCA/Phono type “INPUT” jacks when connecting your subwoofer to a pre-amp, signal processor, or line-level crossover. The “SPeAKeR leVel INPUT” jacks connect directly to the speaker outputs of an integrated amplifier or receiver.
CROSSOVERS EQ-Max User’s Manual FRONT SUBWOOFER OUTPUT JACK AMPLIFIER REAR figure 4. line-level subwoofer Connection Diagram.
CROSSOVERS FRONT RIGHT SPEAKER FRONT LEFT SPEAKER FRONT REAR SUBWOOFER OUTPUT JA CK AMPLIFIER EQ-Max User’s Manual figure 5. speaker-level subwoofer Connection Diagram. Note: Connecting main speakers to the rear panel of the sub is optional.
INTERCONNECT CAbLES EQ-Max User’s Manual When installing your new Velodyne subwoofer using the line-level connections, you should always use shielded phono cables. There are many high quality cables available today. It is recommended that you keep the length of cable as short as possible to avoid any potential noise problems. When using speaker-level connections, use a high quality speaker cable that mates well with the connectors.
USAGE EQ-Max User’s Manual • Volume Control — This control allows you to balance the output from the subwoofer to the main speakers in your system. This control should be set to achieve similar volume level of both the main speakers and subwoofer. When pressing volume up or down, the volume level is shown on the numeric leD on the front panel. WARNING: Some manufacturers preset their receivers with the Sub-Out channel signal at a minimum level.
USAGE EQ-Max User’s Manual The following table indicates musical style and which preset is recommended for it.
MAINTAIN EQ-Max User’s Manual Restoring Defaults There is a feature that allows you to restore default settings for your eq-Max subwoofer. by pressing presets in eXACTly the following order on the remote, the unit will restore its default settings.
MAINTAIN EQ-Max User’s Manual • The subwoofer does not operate normally or exhibits a marked change in performance • The cabinet has been dropped or is damaged • The subwoofer driver’s cone and/or suspension is physically damaged Troubleshoot before seeking service for your amplifier or subwoofer, please re-check all systems. Following is a simple troubleshooting guide to assist you. 1. Verify that the unit is plugged in and power outlet used is active. 2. Is the power switch on? 3.
MAINTAIN EQ-Max User’s Manual If the subwoofer should shut down, reduce the volume setting and shut the subwoofer off until it cools down. The time the subwoofer takes to cool down depends on the ambient room temperature, but typically at least 10 minutes are required for the subwoofer to cool down and recover from the thermal shutdown. Also, plug the unit into a different wall socket.
SPECIFICATIONS model EQ-Max User’s Manual eQ-max8 eQ-max10 eQ-max12 eQ-max15 Woofer 8” (20.3 cm) forward firing (6.3” piston diameter) 10” (24.5 cm) forward firing (8.2” piston diameter) 12” (30.5 cm) forward firing (9.7” piston diameter) 15” (38 cm) forward firing (12.
WARRANTY EQ-Max User’s Manual FOR YOUR RECORDS. . . Date Purchased _____________________________________________________________________________________ Dealer ______________________________________________________________________________________________ Serial # ____________________________________________________________________________________________ Please register your product online. If you don’t have internet access call Velodyne customer service at 408-465-2800 (U.S. or Canada only).
Velodyne Acoustics, Inc. 345 Digital Drive Morgan Hill, CA 95037 408.465.2800 voice 408.779.9227 fax 408.779.9208 service fax www.velodyne.com Service e-mail: service@velodyne.com General e-mail: help@velodyne.