RANGE HOOD INSTALLATION INSTRUCTIONS - USE AND CARE HB0062 MODELS ESB10, ESN10, ESV10, QDE, AND ESC270 ! INTENDED FOR DOMESTIC COOKING ONLY ! READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: CLEANING AND OPERATION INFORMATION ON PAGES 9 AND 10. REGISTER YOUR PRODUCT ON LINE AT: www.venmar.ca SV06727 rev.
! WARNING ! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 1. 2.
ABOUT THIS MANUAL Please take note this manual uses the following symbols to emphasize particular information: ! WARNING Identifies an instruction which, if not followed, might cause serious personal injuries including possibility of death. CAUTION Denotes an instruction which, if not followed, may severely damage the unit and/or its components. NOTE: Indicates supplementary information needed to fully complete an instruction.
1. INSTALL DUCTWORK Plan where and how the ductwork will be installed. Install proper-sized ductwork, elbow(s) and roof or wall cap for the type of blower you are installing. If using 6’’ (150 mm) round ducts, use a transition. Use 2’’ (50 mm) duct tape to seal duct joints. Roof cap Roof cap 6” round duct 3¼” x 10” duct 3¼” x 10” to 6” round transition Wall cap Wall cap Hood Hood HH0014A HH0011A 2. MEASURE THE INSTALLATION Dimensions for the most common installations are shown below.
3. PREPARE THE INSTALLATION Make sure the following items are included: - Hood Filters (2) Adapter/damper assembly 3¼’’ x 10’’ (located inside the hood, under the bottom panel) Compact fluorescent lamps (120 V, 13 W, PLC13, 2700 K with G24q-1 base) (packed behind the light diffuser) Bag of parts (located inside the hood, under the bottom panel) including: (1) wire clamp, (5) no. 8 x 1/2’’ double thread screws, (2) wire connectors and (6) no.
4. PREPARE THE HOOD (CONT’D) Punch out the appropriate electrical knock-out hole. Using a long nose pliers, remove the knock-out for the chosen opening (vertical on top or horizontal at the back of the hood). See figures below. VERTICAL DISCHARGE: HORIZONTAL DISCHARGE: 1 2 3 HD0153 5. INSTALL THE ADAPTER/DAMPER NOTE: If this hood replaces another one, please note that the location of the air exhaust can vary from one manufacturer to another.
5. INSTALL THE ADAPTER/DAMPER (CONT’D) VERTICAL DISCHARGE For a vertical discharge installation only, leave the foldable flange (C) of the adapter/damper as is. This flange must be located towards the front of the hood. See beside. C HO0057 ALL INSTALLATIONS Using two 1/2” screws, secure the adapter/damper to the top or back of the hood. Tape the adapter/damper to the hood using duct tape to seal it. HO0058 NOTES: 1.
. REINSTALL BOTTOM PANEL AND FILTERS Reinstall the bottom panel, using the retaining screw previously removed in step 4 plus 4 others from parts bag. Refer to illustration beside. Then, reinstall filters. HO0092 9. FLUORESCENT LAMPS ! WARNING This hood has fluorescent lamps containing mercury. Dispose of appropriately, according to local laws and requirements. This range hood must use compact fluorescent lamps (120 V, 13 W, PLC13, 2700 K with G24q-1 base) (included).
10. CLEANING The grease filters, bottom panel, intake ring (A) and blower wheel (B) should be cleaned frequently. Use a warm detergent solution. The grease filters, intake ring and blower wheel are dishwasher safe. Clean all-metal filters in the diswasher using a non-phosphate detergent. Discoloration of the filter may occur if using phosphate detergents, or as a result of local water conditions — but this will not affect filter performance. This discoloration is not covered by the warranty.
11. OPERATION Always turn on the hood before beginning cooking in order to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after turning off the range. ROCKER SWITCH CONTROL A HC0031 B A. ON/OFF BLOWER AND SPEED CONTROL SWITCH: This 3-position rocker switch controls the blower speed. Pressing on left side (1) will result in low speed operation, while pressing on right side (2) will turn on the blower to high speed.
12. SERVICE PARTS MODELS ESB10, ESN10 AND ESV10 1 KEY PART No. No. 2 3 4 1 2 3 4 5 6 * 13296 03623 01752 01988 01757 14131 SV06727 * 04281 DESCRIPTION ADAPTER/DAMPER FLUORESCENT LAMP LIGHT DIFFUSER BLOWER WHEEL INLET RING MICROMESH FILTER (THE PAIR) INSTALLATION & USER MANUAL HARDWARE BAG: (1) WIRE CLAMP, (2) WIRE CONNECTORS, (6) NO. 6 X 1/2” SCREWS, (5) NO. 8 X 1/2” DOUBLE THREAD SCREWS QTY. 1 2 1 1 1 1 1 1 * Item not shown 6 5 HL0092 MODEL ESC270 1 2 3 4 KEY PART No. No.
. SERVICE PARTS MODEL QDE 1 2 3 4 12 5 11 6 10 7 9 8 HL0095 KEY PART No. No. DESCRIPTION QTY. 1 1 SV13296 ADAPTER/DAMPER 1 2 SV15434 ROCKER SWITCH WHITE (PAIR) + OVERLAY WHITE 1 SV15433 ROCKER SWITCH BLACK (PAIR) + OVERLAY BLACK 2 3 SV03623 FLUORESCENT LAMP 1 4 SV01752 LIGHT DIFFUSER 1 5 SV01765 MOTOR 1 6 SV01988 BLOWER WHEEL 1 7 SV16119 BOTTOM PAN WHITE 1 SV16117 BOTTOM PAN BLACK 8 SV01757 INLET RING 1 1 9 SV14131 MICROMESH FILTER (THE PAIR) 1 10 SV02104 SECONDARY CAPACITOR 7.