COMM’S DOM HEADSET PS3 VX Comm's Freedom Headset_User guide_VA:Layout 1 9/8/10 TM www.venomuk.com Venom Ltd. Solution House, Sandon Road, Therfield, Hertfordshire SG8 9RE Venom is a trademark of Venom Ltd. sales@venomuk.
PS3 VX Comm's Freedom Headset_User guide_VA:Layout 1 9/8/10 User guide contents 3. Basic use 3.1 Adjust the earphone volume 1. Introduction 1.1 Bluetooth wireless technology 4. Battery information 2. Getting started 2.1 Overview 2.2 Chargers and batteries 2.3 Switching the headset on and off 2.4 Pair the headset with a compatible device (PS3TM) 2.5 Disconnect the headset from the device 2.6 Reconnect the paired headset to your device 2.7 Troubleshooting 5.
PS3 VX Comm's Freedom Headset_User guide_VA:Layout 1 1. Introduction 1.1 Bluetooth wireless technology Thank you for purchasing the VX Comm’s Freedom Headset. Bluetooth wireless technology makes it possible to connect compatible communication devices without using cables. A Bluetooth connection does not require that the device and the headset be in line of sight, but both devices should be within 10 metres (30 feet) of each other.
PS3 VX Comm's Freedom Headset_User guide_VA:Layout 1 Fig: 1 1 2 3 4 5 9/8/10 Key to figure 1 1. Indicator light 2. Volume up button 3. Power and synchronise button 4. Volume down button 5. Mini USB port 2.2 Chargers and batteries The VX Comm’s Freedom Headset is intended for use with the mini USB charge cable provided. This device has an internal, rechargeable battery. Connect the charge cable to the headset.
PS3 VX Comm's Freedom Headset_User guide_VA:Layout 1 1. Connect the mini USB charge cable to your PS3TM. The red indicator light is displayed during charging. If charging does not start, disconnect the charger, plug in again and retry. Charging the battery fully may take up to 2 hours. 2. When the battery is fully charged, the red indicator light will turn blue. Disconnect the charger from the mini USB outlet and the headset.
PS3 VX Comm's Freedom Headset_User guide_VA:Layout 1 for 8 seconds until the blue and red light flash alternately. 3. On your PS3™ systems home menu, go to (Settings), then (Accessory Settings) and select (Manage Bluetooth Devices). 4. Select (Yes) to pair (Register) the headset with the PS3™ System. 5. Select (Start Scanning) The PS3™ System will then scan for all Bluetooth devices and then the devices will be displayed. 6. Select the headset (Venom) when prompted for the passcode enter 0000. 7.
PS3 VX Comm's Freedom Headset_User guide_VA:Layout 1 2.6 Reconnect the paired headset to your device To connect the headset to your device, switch on the headset. 2.7 Troubleshooting If you cannot connect the headset to your device, do as follows: • Ensure that the headset is charged, switched on, paired with and connected to your device. • Ensure that the Bluetooth feature is activated on your device.
PS3 VX Comm's Freedom Headset_User guide_VA:Layout 1 complete charge and discharge cycles. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Recharge your battery only with compatible chargers designated for this device. Unplug the charge cable from your PS3TM when not in use. Do not leave a fully charged battery connected to a charger, since overcharging may shorten its lifetime. If left unused, a fully charged battery will lose its charge over time.
PS3 VX Comm's Freedom Headset_User guide_VA:Layout 1 • Keep all accessories and enhancements out of the reach of small children. • Keep the device dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, allow it to dry completely. • Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged. • Do not store the device in hot areas.
PS3 VX Comm's Freedom Headset_User guide_VA:Layout 1 9/8/10 16:44 Page 19
