CTB - 275 Ecowatt IDEO Installation Manual
Before manipulating this device, disconnect the electricity supply. During normal operation, never stop the ventilation system.
General Information High-performance heat recovery dwelling unit 1 Introduction This manual is destined for use with the IDEO 275 Ecowatt high high-performance performance heat recovery unit and its peripheral fittings (conduits, inlets, regulators…). Its aim is to provide the maximum information and safety during installation, set-up and use. As our products are in constant evolution, Soler & Palau reserves the right to modify this manual without prior notification. 1.
2 Technical information 2.1 General definition The IDEO 275 Ecowatt provides optimum ventilation for a room with a minimum loss of energy. It extracts air from spaces such as (Bathroom/s, (Bathroom/s WC, WC kitchen and washroom/s or shower room/s room/s, and supplies fresh air into the main rooms (Living rooms, bedroom/s, office, …). The fresh and extracted airflows are separated and filtered. Only the energy from the extracted air is transferred to the new fresh air introduced.
New fresh air inlet: The conduit from the outside is connected here. To avoid condensation, it is recommended to use insulated conduits. The new fresh air inlet should be fitted sufficiently far from any source of strong contamination (Trees, combustion fumes, roads …). Supply fresh air into the building: The conduit blowing fresh reheated air into the building is connected here. To avoid thermal losses losses, it is recommended to use insulated tubes for moving the warmed air.
2.
2.4 Placement On a vertical wall: On the floor: Wall bracket It is recommended to locate IDEO in heated house space. Otherwise it will be necessary to insulate the condensate drain pipework..
On the floor: An specific kit option Support It is recommended to locate IDEO in heated house space. Otherwise it will be necessary to insulate the condensate drain pipework pipework.
DIAGRAM OF STANDARD ASSEMBLY TYPE “DELIVERY” Outlet roof caps CT 150 Kitchen BDOP 125 BDOP 80 Toilets Air intake plenum Or PAP Air intake D150 Or Living/sitting Li i / itti room & Bedrooms PAF 150 Circular Air intake wall hoods Or PAST Air intake roof D150 10 spigots distributor
DIAGRAM OF STANDARD ASSEMBLY TYPE “DISTRIBUTION” Outlet roof caps Living/ sitting room CT 150 Kitchen BDOP 125 BDOP 125 + BDOP D80 + RD80 Bedrooms Toilets BAR + Or PAP Air intake D150mm Or PAF 150 Circular Air intake D150mm Or PAST Air intake roof hoods D150mm BDOP D80 + RD80
2.5 Characteristics and electrical connections Connect the supplied cable to the mains, using a hermetic connection box. H05VV-F-5G1 type cable Length 1.2 m Connection box Electrical panel Power supply: Single phase 230VAC-50Hz Electrical protection: 3A Maximum power: 190 Watts Max. ambient temperature: 50º C Max.
.2.3 Controlling the IDEO 275 Ecowatt The IDEO 275 Ecowatt can be controlled from: • A button that enables the boost flow for the kitchen to be timed in ½-hour steps. Service life with normal usage (average 3 times a day) is estimated to be about 4 and a half years. For each operation, a red signal will light up for a few seconds to indicate battery life. The button uses one CR2032 type battery. • The programming module is located on the front of the machine machine.
2.2.a .
2.2.b . Functions of the programming module: (1) • Adjustment using the clock: Navigate with keys 19 or 20 to pictogram 1 showing a clock. Select with key 18 18. The pictogram will flash flash. Validate with key 18 18. Adjust the desired hour using keys 19 and 20. Validate with key 18. Pictogram 3 (day) will flash. Validate with key 18. Adjust the day, knowing that the succession can be destined from 1 to 7 on any day.
- Auto 2: Working week with three meals per day and the weekend, starting breakfast two hours later.
• Conditions for the filter icon to be displayed (12): This icon will be displayed when one or several filters are soiled and it is necessary to clean or replace them. 9 F1 = Blowing filters 9 F 2= Extraction filters The time it takes for the filter to become soiled can be highly variable according to the conditions of use and where the house is located (level of outdoor pollution depending on whether it is an industrial area, near roads or motorways, forest or agricultural areas).
