9” LCD TV PLV76198E OWNER’S MANUAL PLV76198S23E10 IB ENG.
Safety Precautions SAFETY INFORMATION caution • When connecting or disconnecting the AC power cord, grip the plug and not the cord itself. Pulling the cord may damage it and create a hazard. • When you are not going to use the unit for a long period of time, disconnect the AC power cord.
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (Including amplifiers) that produce heat.
Table of Contents Safety Precautions.............. 2 INSTALLATION............................ 11 INSTALLING / REMOVING THE BASE STAND..........................................................11 IMPORTANT SAFETY INSTRUCTIONS............................ 3 MOUNTING ON THE WALL.........................11 Table of Contents................. 4 TV SETUP.............................. 12-13 QUICK INSTALLATION................. 5 PICTURE MENU...........................................12 AUDIO MENU...............
QUICK INSTALLATION When you turn on your television set for the first time, be sure to place it on a solid stable surface. To avoid danger, do not expose the TV to water, or a heat source (e.g. lamp, candle, radiator). Do not obstruct the ventilation grid at the rear and be sure to leave sufficient gaps around the unit as shown. 2 3/8” 7 7/8” 2 3/8” 1. Connect an antenna or Cable TV COAX cable to the TV's antenna input jack. 2. Connect the power cord. 3. Press the / ON button to turn on the unit. 4.
ACCESSORIES Please check and identify the supplied accessories. Remote control (with batteries)............................................................................................................................. x 1 GETTING STARTED USING THE REMOTE CONTROL • Point the remote control at the remote sensor located on the unit. • When there is a strong ambient light source, the performance of the infrared remote sensor may be degraded, causing unreliable operation.
CONTROL REFERENCE GUIDE Remote control 1) MUTE Button Press to turn off the sound. 2) MENU Button Press to display the on-screen menu or switch back to the previous menu screen. 3) CURSOR ( , , , ) Buttons Use to highlight selections on a menu screen and adjust certain settings. ENTER Button Confirm selection on a menu screen. 4) DISPLAY Button 5) VOL + / VOL - Button 6) LAST CH Press to display information on the current channel. Press to increase/decrease the volume.
CONTROL REFERENCE GUIDE tv 1 4 7 2 3 5 6 8 9 1. 2. AUDIO IN (Left/Right) / VIDEO IN jacks 10 / ON button Turns the unit on and off. 3. MENU button Enters the on-screen TV menu. 4. 11 12 FUNCTION button Selects TV / AV. 5. CH / CH buttons Press to confirm selections on the TV menu screen and 6. / to change TV channels. VOL + / VOL - controls Adjusts the volume level and highlights selections (Left & Right) on the TV menu screen. 7. 8.
CONNECTIONS CONNECTING A TV ANTENNA To view television channels correctly, a signal must be received from one of the following sources: - An indoor or outdoor aerial antenna - A cable system - A satellite system NOTE For optimal reception of over-the-air TV broadcasts, we recommend that you use an external fixed antenna. If using an indoor antenna, please ensure that you purchase an antenna with sufficient ability to receive signals in your home.
CONNECtions connect the Power cord • Connect the AC power cord into a wall outlet. • Press the / I button on the unit or remote control to turn on the unit. NOTE • Be sure the AC power cord is disconnected and all functions are off before making connections. • Make sure that all the components are connected correctly. • To prevent electrical shock, match wide blade of plug to wide slot of wall outlet, then fully insert.
INSTALLATION INSTALLING / REMOVING THE BASE STAND WARNING: The LCD Display is very fragile, and must be protected at all times when removing the base stand. Be sure that no hard or sharp object, or anything that could scratch or damage the LCD display, comes into contact with it. Do NOT exert pressure on the front of the unit at any time because the screen could crack. 1. Disconnect all cables or cords connected to the unit. 2. Lay the unit down on a flat surface with the back side facing up.
TV SETUP PICTURE MENU 1. Press the MENU button. 2. Press ENTER or button to highlight Picture Mode. 3. Use the or button to select other options (Contrast, Brightness, Sharpness, Color, Tint, Aspect Ratio & Color Temperature). 4. Use the ENTER or button to make adjustment. The screen will adjust to your selected setting immediately. 5. Repeat steps 3 to 4 to adjust other options. 6. Press button to return to the previous menu. 7.
TV SETUP TV MENU 1. Press the MENU button. 2. Use the or button to select TV setting. 3. Press ENTER or button to highlight Antenna, then use the or button to select other options (DTV Signal, Auto Scan, Auto Scan Add CH, Channel Skip & Channel Labels). 4. Use the ENTER or button to make adjustment. The screen will adjust to your selected setting immediately. 5. Repeat steps 3 to 4 to adjust other options. 6. Press button to return to the previous menu. 7.
TROUBLESHOOTING GUIDE SYMPTOM CAUSE (AND REMEDY) No power. • Check that the AC power cord is connected. • The unit is not turned on. The remote does not function. • • • • Remove any obstacles between the remote and the unit. Use the remote near the unit. Point the remote at the remote sensor on the unit. Replace the batteries in the remote with new ones. TV Bad Picture (snow, multipe images, distortion, blurry) • Check the location of the antenna and adjust it if necessary.
LIMITED WARRANTY VENTURER ELECTRONICS (“VENTURER”) makes the following limited warranty. This limited warranty extends to the original consumer purchaser and is limited to non-commercial use of the product. Ninety (90) Day Parts & Labor Warranty VENTURER products purchased in the United States are warranted to be free from defects in materials or workmanship for a period of ninety (90) days from the date of their original retail purchase.
LIMITED WARRANTY All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are expressly limited to the duration of the limited warranties set forth above. With the exception of any warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair or replacement of any parts.
