Installation Guide

Supplied by:
Door Frame Set
7181
1-1/4" x 4-9/16"
Brick Mould Set
7137
1-1/4" x 2"
Brick Mould
2448
1-1/4" x 2"
Door Frame System
Brick Mould
2448
1-1/4" x 2"
Florida Brick Mould
7252
11/16" x 1-5/8"
Brick Mould
7371
1-1/4" x 2"
Window and Door Trim
Fluted Casing
7209
1" x 3-1/2"
Trimplank 5/4x4
7482
1" x 3-1/2"
Trimplank 5/4x6
7483
1" x 5-1/2"
RB3 Casing
2369
1" x 3-1/2"
Drip Cap
2449
11/16" x 1-5/8"
Sill
7117
1-1/4" x 5-1/4"
Sill Nose
7118
1-5/16" x 1-3/8"
Bed Mould
2598
9/16" x 1-9/16"
Shingle Mould
2599
11/16" x 1-5/8"
Decorative Exterior Mouldings
Colonial Stop
7788
3/8" x 1-1/4"
Outside Corner
7719
1-1/8" x 1-1/8"
Base Cap
2450
11/16" x 1-1/8"
Lattice
2018
1/4" x 1-35/64"
Parting Bead
2851
7/32" x 1-1/4"
Stop
2046
5/16" x 3/4"
Quarter Round
2689
3/4" x 3/4"
Quarter Round
2024
1/2" x 1/2"
Colonial Casing
2355
11/16" x 2-1/4"
Colonial Base
7527
9/16" x 3-1/4"
Stop
2363
3/4" x 1"
Blind Stop
2330
5/8" x 5/8"
Trimplank 2x2
2542
1-1/2" x 1-1/2"
Trimplank 1x2
2150
5/8" x 1-1/2"
Trimplank 1x4
7318
3/4" x 3-1/2"
Trimplank 1x6
7311
3/4" x 5-1/2"
Trimplank
®
PVC Boards
Trimplank 1x8
7312
3/4" x 7-1/4"
Trimplank 1x10
7440
3/4" x 9-1/4"
Trimplank 1x12
7439
3/4" x 11-1/4"
Trimplank 5/4x4
7482
1" x 3-1/2"
Trimplank 5/4x6
7483
1" x 5-1/2"
Flat Utility Trim
2709
5/16" x 5-13/16"
Exterior Planking
2352
3/8" x 5-1/2"
Quarter Round
2689
3/4" x 3/4"
Scotia/Cove
2021
3/4" x 3/4"
Exterior Bead
2258
1/2" x 13/32"
Ceiling and Wall Solutions
Sawing/Cutting:
• Use standard woodworking
equipment for most applications
• If using a power miter saw, a
carbide-toothed blade with 80
teeth or more is recommended
Nailing:
• Use 6d and 8d galvanized nails
• Place nails 12" on center,
approximately ¾" from each edge
• Pre-drilling is required at
temperatures of 40˚ F or below
• Veranda moulding can also be installed
using a pneumatic nailer, with stainless
steel or painted head screws or with
construction grade adhesives
Gluing:
• To reduce or eliminate open
joints, pipe glue or PVC pipe
cement is recommended
• Temperature variations will cause PVC
moulding to expand and contract
Painting:
• Veranda moulding with factory-applied
Readi-Finish
®
requires no painting
• Oil based or latex paints can be
used to achieve custom finishes
• For darker custom colors (colors
that fall within the lightness (L) value
of 56 to 0, with 100 being white
and 0 being black), the use of heat-
reflective paint is recommended
Cleaning:
• Veranda moulding can be cleaned
using any of the recommended
household cleaners listed below;
however, glass cleaner has been shown
to be best at keeping the finish intact
• Recommended cleaners: Windex, 409
Glass and Surface Cleaner, Spic &
Span Cinch, Fantastik All Purpose, etc.
• Apply the cleaning solution and
immediately wipe dry for best results
• Avoid harsh cleaners with glycol ethers,
ethanol type solvents and/or isopropyl
alcohol as they can soften the PVC
finish if left on for several minutes
INSTALLATION TIPS
VINYL MOULDING & TRIM
nLifetime No Rot
®
material constructed from 100% Cellular Vinyl PVC
®
nMoisture and termite proof
nLow maintenance, easy to clean
nPrefinished, no painting required
n10 year factory finish warranty
Garage Door Stop
2149
7/16" x 2"
Brick Mould
2448
1-1/4" x 2"
Jamb
2497
11/16" x 5-13/16"
Flat Utility Trim
2709
5/16" x 5-13/16"
Garage Door Trim System
BASIC & DECORATIVE SOLUTIONS
VINYL MOULDING & TRIM
V000000