Instructions / Assembly

ManualsBrandsVeranda ManualsFencingPro Series 4 ft. W x 6 ft. H White Vinyl Woodbridge Baluster Top Privacy Fence Gate

68956 U.S. Hwy 131, White Pigeon, MI 49099 1-855-556-1852 10410_1/19

www.ufpi.com

Dig post holes 18" to 24" in diameter and 36" to 48" deep

(depending on local ordinance or expected frost depth in winter).

Backﬁ ll the holes with 6" of gravel. See ﬁ g. 1.

The gate can be set up left swing or right swing. Consider swing

direction when determining which post will be your hinge post.

Mix concrete in the hole for the hinge post per the instructions

on the bag. Install the post into the hole and tap the post to the

proper depth. We recommend inserting a piece of 4x4 to support

the gate hinge post. Using a level, ensure post is plumb. Brace

the post with temporary supports as the concrete sets (per the

instructions).

Repeat with second hole.

Check local ordinances and regulations before building your

fence. Before construction, contact your local utility companies

to mark any underground cables and pipelines. In addition, it is

a good idea to discuss plans with any neighbors along your

proposed fence line.

Step 3Preparation

Digging post holes

Items you may need

• Drill driver with 1/8" and

1/4" Drill bits

• 7/16" wrench

• Tape measure

• Pencil

• Safety glasses

• 4x4 treated wood post

• Blocks or clamp

• 2 – Gate Jambs with covers

Kit contents

• 2 – Top/Bottom rails

• 1 – Mid rail

• 2 – Gate jambs with covers

• 7 – Picket panels

• 9 or 11 – Top pickets

• Hardware kit

PRO SERIES PICKET TOP PRIVACY GATE – ASSEMBLY INSTRUCTIONS

36" to 48"

In-Ground

18" to 24" Dia. Hole

Filled with Concrete

4x4 Wood

Insert

Hinge Post

Latch Post

47-3/4" Gate

Opening

ﬁ g . 1

Open Top

Picket Gate

Closed Top

Picket Gate

46½" W 46½" W

69½" H

Summary of content (4 pages)

PAGE 1
PRO SERIES PICKET TOP PRIVACY GATE – ASSEMBLY INSTRUCTIONS Kit contents • 2 – Gate Jambs with covers • 2 – Top/Bottom rails • 7 – Picket panels • 1 – Mid rail • 9 or 11 – Top pickets • 2 – Gate jambs with covers • Hardware kit Open Top Picket Gate Closed Top Picket Gate • Pencil • 7/16" wrench • 4x4 treated wood post • Tape measure • Blocks or clamp • Safety glasses 46½" W 69½" H • Drill driver with 1/8" and 1/4" Drill bits 69½" H Items you may need 46½" W Preparation Step 3 Check local
PAGE 2
PRO SERIES PICKET TOP PRIVACY GATE – ASSEMBLY INSTRUCTIONS Assembling and Hanging the Gate STEP 1 Assemble gate components on a flat, clean surface. Insert the picket panels between the top and mid rails (fig. 2a). Slide the top pickets in the routed holes in the mid rail. Place the top rail on top of the pickets (fig. 2b). STEP 4 Align the rails on the gate with the rails on the existing fence. There must be at least a 2" gap from ground to bottom rail for the gate to function properly.
PAGE 3
PUERTA DE PRIVACIDAD CON TABLONES SUPERIORES PRO SERIES – INSTRUCCIONES DE ENSAMBLADO Un kit incluye • 2 – Gate Jambs with covers • 2 – Rieles superior/inferior • 7 – Tableros de tablones • 1 – Riel intermedio • 9 u 11 – Tablones superiores • 2 – Jambas con cubiertas • Juego de herrajes Puerta de tablones con parte superior abierta • Lentes de seguridad • Llave de 1.1 cm (7/16 pulg.) • Bloques de soporte o abrazadera • Cinta métrica • Poste de madera tratada de 10.2 x 10.2 cm (4 x 4 pulg.) 176.
PAGE 4
PUERTA DE PRIVACIDAD CON TABLONES SUPERIORES PRO SERIES – INSTRUCCIONES DE ENSAMBLADO Ensamblado y colocación de la puerta PASO 1 Coloque los componentes de la puerta en una superficie plana y limpia. Inserte los tableros entre el barandal superior y el intermedio (fig. 2a). Deslice los tablones superiores en los agujeros del riel intermedio. Coloque el riel superior sobre los tablones (fig. 2b). PASO 4 Alinee los rieles de la puerta con los rieles de la cerca existente.