Instructions / Assembly

ManualsBrandsVeranda ManualsFencingPro Series 4 ft. W x 6 ft. H White Vinyl Woodbridge Baluster Top Privacy Fence Gate

To complete your project, you will also need:

 •Drilldriverwith1/4”and1/8”drillbits

 •7/16”wrench

 •Tapemeasure,pencil/markerandsafetyglasses

 •treatedwoodpost

Planning

 •Priortoconstruction,checkwithyourlocalregulatoryagency

  forspecialcoderequirementsinyourarea.

 •Contactyourutilitysuppliertolocateandmark

  undergroundlines.

 •Carefulplanningandmeasuringofyourfenceprojectis

  essential,asmovingpostsaftertheconcretesetsis

  extremelydifcult.

Digging Post Holes

 •Digpostholeforthehingepost18”to24”indiameterand

  36”to42”deep(dependingonlocalordinanceorexpected

  frostdepthinwinter).Werecommendthatyouinsertapieceof4x4treatedlumbertosupportthegatehingepost.

  SeeFig.1.

 •Actualgatesizewillvary.Theinsidepost–to-postdimensionwillbethewidthofthegateplus1-1/4”.

Double-check all measurements!

Assembling and Installating the Gate

 •Measuretobesureyoucaninstallthegatetothepostwithapproximatelya2”gapfromthegroundtothebottomof

  thegate.Aligntherailsonthegatetotherailsonthefencepanels.

 •Layallgatecomponentsoutonaat,cleansurface.

 •Placegatejambsonbothsidesoftherailsandplacethehingesinthecenterofthefencerail.Usingthehingeasa

  guide,drillthefour(4)necessary¼”holesforthehingebolts.Ensuretherailsarefullyinsertedinthejambbefore

  drilling.Theboltsneedtogothroughthejambandrailtofunctionproperly.SeeFig.2.

 •Slidethehingedbracketandbracketonthetopandbottomofthegatejambs.Attachhingestojambswiththe

  suppliedthroughbolts.Connectboltswiththesuppliedcapnuts.Ensurethegateissquarebeforeallboltsaretight.

  Whensquare,tightenallboltswith7/16”wrench.SeeFig.2.

 •Hangthegatebetweentheposts.Usea5/8”spacerbetweenthegateandtheposts.SeeFig.3.Secureinplacewith

  shimsunderthegateorclampthejambonthegatetothepost.Makesurethegateislevelandsquare.Attachhinge

  bracketstothegatepostwiththeprovidedscrews.SeeFig.4.

 •Removeanyclampsandshims.Attachlatchusingscrews

  provided.SeeFig.5.

 •InstallapostcaponeachpostusingPVCcementoran

  exterioradhesive.

Pro Series Privacy Gate

For use with product codes: 118677, 144714, 144710, 118677, 118678, 144715,

144718, 144719, 144716

Installation Tips

ﬁg. 2

5/8

Fig.4 DoverGateSpacer.ai

ﬁg. 3

Summary of content (4 pages)

PAGE 1
Pro Series Privacy Gate For use with product codes: 118677, 144714, 144710, 118677, 118678, 144715, 144718, 144719, 144716 Installation Tips To complete your project, you will also need: • • • • Drill driver with 1/4” and 1/8” drill bits 7/16” wrench Tape measure, pencil/marker and safety glasses treated wood post Planning • Prior to construction, check with your local regulatory agency for special code requirements in your area. • Contact your utility supplier to locate and mark underground lines.
PAGE 2
Note: The gate latch is designed to be used on the left or right hand side of the gate, depending on customer preference or design. The latch is assembled, ready to be installed on the right hand side of the gate. If you desire to switch the latch follow these simple steps: • • • • Remove the 2 shoulder bolts and spring. Change orientation of the clicker Re-attach spring and insert shoulder bolts. Shoulder bolts must be fully tightened. Thread locking adhesive is recommended. fig. 4 Striker Latch fig.
PAGE 3
Puerta de privacidad de la serie Pro Para uso con productos código: 118677, 144714, 144710, 118677, 118678, 144715, 144718, 144719, 144716 Consejos de instalación Para completar su proyecto, usted necesitará: • • • • Destornillador taladro con broca de taladros de 1/4 plg y 1/8 plg Llave inglesa de 7/16 de pulgada Cinta métrica, lápiz/marcador y lentes de seguridad Poste de madera Planificación • Antes de la construcción, consulte con su agencia regulatoria local para ver si hay requisitos de un código
PAGE 4
Nota: El pestillo de puerta Dover está diseñado para ser utilizado en el lado izquierdo o derecho de la puerta, dependiendo de la preferencia del cliente o del diseño. El pestillo está montado, listo para ser instalado en el lado derecho de la puerta. Si desea cambiar el pestillo siga estos sencillos pasos: • • • • Quite los 2 pernos de ajuste y el resorte. Cambie la orientación del clicker. Vuelva a colocar el resorte e inserte los pernos de ajuste. Los pernos de ajuste deben estar bien apretados.