Installation Guide

ManualsBrandsVeranda ManualsOther5 in. x 5 in. New England Vinyl Post Cap with Glue

Owner's Manual

Version

4.0

Elite Rail

Assembly and Installation Instructions

PLEASE READ OWNER'S MANUAL COMPLETELY

BEFORE ASSEMBLING YOUR RAIL.

ALL STATED SIZES ARE NOMINAL DIMENSIONS.

34106625BOM V4 6/13

73013042 / 73013043 / 73013044 / 73013048

73013049 / 73013050 / 73013051 / 73013052

73013053 / 73013054 / 73013055 / 73013056

73013069 / 73013071 / 73013073 / 73013079

73013080 / 73013081 / 73013085 / 73013086

73013087 / 73013088 / 73013095 / 73013096

73013282 / 73013306 / 73013307 / 73013308

73013314 / 73013315 / 73013316 / 73013317

73013318 / 73013319 / 73013320 / 73013321

73013335 / 73013345 / 73013346 / 73013347

73013348 / 73013349 / 73013841 / 73013842

73013843 / 73013844 / 73013845 / 73013846

73013847 / 73013848 / 73013849 / 73013850

73013851 / 73013852 / 73013853 / 73013854

73013855

Summary of content (8 pages)

PAGE 1
Elite Rail Assembly and Installation Instructions PLEASE READ OWNER'S MANUAL COMPLETELY BEFORE ASSEMBLING YOUR RAIL. ALL STATED SIZES ARE NOMINAL DIMENSIONS.
PAGE 2
Thank you for choosing the Barrette Outdoor Living Railing. Please read the instructions completely before assembling your rail. Retain manual and your dated sales slip for future reference and warranty claims. Before You Begin… Make sure your project meets local building codes before beginning installation.
PAGE 3
TIP: Precision cuts required to ensure optimum tight installation and fit. Use chopsaw with thin carbide tip blade to ensure smooth cuts. Pay particularly close attention to angle cuts to ensure tight fit. 1 Install Post Sleeves and Base Trim 1.1: Closely follow post install kit instructions (or sleeve existing wood 4x4) - Instructions included in Post Install Kit (sold separately). 1.2: Trim Post sleeve to desired length. (39" is recommended for a 36" finished rail height.
PAGE 4
3 Prepare the Bottom Rail 3.1: Install lower rail brackets. Position the provided bracket install template on the top of the installed post base trim. Use template to align the bottom brackets to the center of the post sleeve, making sure "THIS SIDE UP" on bracket faces up. Pre-drill bracket holes with 1/8" drill bit and attach bracket with #10 x 2-1/2" supplied screws. 3.2: Install Center Support Brace A.
PAGE 5
5 Prepare the Top Rail 5.1: Plug in top brackets to chassis with "This Side Up" facing up to the top. 5.2: Attach the bracket to the chassis with a supplied #8 x 5/8" self tapping screw in groove in chassis. Repeat on opposite side. (NOTE: For 10' rail kits, chassis will be made of aluminum and should be pre-drilled with 1/8" drill bit.) 5.3: Turn chassis upside down and lay baluster spacer on top of chassis.
PAGE 6
6 7 Installing the balusters 6.1: Slide top rail over the top of the assembled “chassis” fitting snug to posts. 6.2: Through the holes in the top rail baluster spacer made in Step 5.7, screw the provided #10 x 2" screws through the baluster spacer and chassis into the top rail to connect the assembly. Installing Elite Railing on Angles 7.1: Use wood 2x4 as a template prior to cutting Elite railing on angles. 7.2: Place 2x4 on top of posts in which angle cut is needed.
PAGE 7
8 Installing the Deck Board in “Over the Top” Format Note: Make sure posts are at same height as rail installation (with a good, tight installation, post and post sleeve to be cut to 35 13/16" high) 8.1: Follow instructions from Steps 2-3-4-5. 8.2: Place deck board (sold separately) over the top rail. Attach with board manufacturer recommended 2" screws into center of rail, through board, ensuring screws engage chassis.
PAGE 8
Transferable Limited Lifetime Warranty What is covered: Barrette Outdoor Living warrants vinyl and aluminum products to include; vinyl and aluminum fence, vinyl and aluminum railing and plastic lattice against defects or workmanship for as long as you own your home. Barrette Outdoor Living will at its option replace the product in question with new product of the same or equivalent value at no charge.