VERBATIM CSP243/CSP247 COPYSMARTPLUS CD Duplication Tower User Manual CSP247 CSP243 – V1.
Chapter 1 Introduction 1.1 Overview Users who want to backup their CDs normally have go through many steps by turning on their computer, launching the software, setting up various parameters, and tiding up their computer. Sometimes it can take up to an hour to get only a few CD backups. A standalone CopySmartPlus will easily resolve this inconvenience. CopySmartPlus is a CD-to-CD standalone duplicator and does not need to connect to a computer.
Chapter 2 Installation and Operation Procedure Unpack the duplicator. Check the entire unit to see if there is any mal-function or damage found. Make sure that the voltage setting is correct. Connect power cable. Switch on the CopySmartPlus with the front power button. 2.1 Key Functions and Operating Instructions LCD Display Panel: Displays main functions and all messages. Scroll up through menus or functions. Scroll down through menus or functions. Executes the function which you select.
2.2 Quick Start • Place master disc in CD-ROM. • Switch to Copy function by pressing arrow button. • Place a blank CD-R or CDRW disc into each the CD writer. • Press “ENT” button to start copying once all writers detect the CD discs (front panel lights stop flashing). • When Copy is completed on all CD writers, the passed CD disc will be ejected (Default setting: discs passed will be ejected. This can be changed according to your need).
Chapter 3 Function 3.1 Copy When running the coping process, the data will really burn into the blank CD-R/RW discs. Before starting the coping process, please make sure the master CD is put in the CD-ROM drive before coping. 1. Copy Place blank CD-R/CD-RW discs into the CD writers. When all writers detect the CDs, press “ENT” button, duplicator will start copying. Copying-24X 0% 650.0MB 74:00 1.Copy OK: 03 LCD will show the process of copying the disc.
3.3 Test & Copy 3.Test & Copy Press “ENT” button to do the disc testing then really write the data on the disc or press “ESC” to exit. Testing-24X 0% 650.0MB 74:00 Copying-24X 0% 650.0MB 74:00 3.Test & Copy OK: 03 Before starting the copying process, the writers will simulate the data writing process. When testing process is completed, duplicator will start writing data onto the CD-R/ RW disc. The CD-R/RW discs will contain data.
Compare OK: 3 Fail: 0 Diff: 0 Src: 01 CD-ROM Total: 650.0MB Src: 02 CD-RW Identical Compare OK: 2 Fail: 1 Diff: 0 Src: 01 CD-ROM Total: 0 Bytes Src: 02 CD-RW TOC not match When the process is finished, the LCD will show the result of the “Compare” process. The CD discs will be ejected by CD writer. Press “ENT” button to see the results of “Compare” If the compare result is identical, the LCD will show the message as left.
3.7 Disc Info This function will show the total amount information on the master disc. 7.Disc Info Press “ENT” button to show the disc information or press “ESC” to exit. Total 02 Sessions Total 10 Tracks Total: 74:00 Total: 650 MB Session 01 Track 01 – 09 Track 01 AUDIO 03:54 The LCD will show the total sessions and tracks on the master disc. Press “ENT” button again, the LCD will show the total time and capacity on the master disc.
3.10 Edit Track This is a track-selecting function that can combine tracks on different CD discs into one single CD disc. For example, you can make a collection of favorite songs from different music CDs and store them into one CD disc. 10. Edit Track Press “ENT” button and arrow button to select or press “ESC” to exit. 3.10.1 CD to CD Edit Select “CD to CD Edit” to choose the CD track on the CD-ROM, then you can copy directly from CD to CD. 10-01.
Select Track: End 2Trk07:50 End edit disc and burn?Yes Copying- 24X Edit 1/10 - > 2/2 Burn Complete! OK: 03 Continue edit next Disc?No Close all disc’s session? Yes Closing Session Please wait--- Finally, when the track of selection is made. Please use arrow button to move to the “End” menu. Press “ENT” button to finish the disc editing, using arrow buttons to make “Yes” or “No” selection. LCD will show the process of “CD Edit” copying process.
3.10.4 Close Session Selecting “Close Session” will make the disc close and you cannot write any additional data to it. This function is required to allow the disc to be read on normal player. 10-04. Edit Track Close Session Close all disc’s session? Yes Closing Session Please wait--Closing Complete OK :3 Fail :0 Press “ENT” button to close session; “ESC” button to bring you to next setting. System will ask a confirmation to close the disc’s session.
3.11.3 Read Speed Sets the reading speed of the target source CD-ROM. 11-03. Setup Read Speed Read Speed 32X Press “ENT” to enter the setting and “ESC” to exit. Use arrow buttons to change the reading speed then press “ENT”. (Depends on the CDROM maximum speed support) 3.11.4 Auto Start Drive Use this setting to auto start copy or test when the blank discs are inserted into the CD/RW drives. Default setting is “Off”. 11-04.
3.11.7 Auto Compare This setting controls auto compare of the data between master and target discs after discs copy. Default setting is “Off”. 11-07. Setup Auto Compare Auto Compare Off Press “ENT” button to enter “Auto Compare” and “ESC” to exit. Use arrow buttons to change “On” or “Off” setting then press “ENT” or press “ESC” to go back. 3.11.8 Auto Prescan This setting controls the auto prescan of the master of the disc and tests the reading speed. Default setting is “OFF”. 11-08.
3.11.10 Burn on The Fly This setting controls the writing methods of the CD writers. When the setting is “On”, the data will direct copy from source drive to the target drives. 11-10. Setup Burn On The Fly Burn On The Fly On Press “ENT” button to enter “Burn On The Fly” and “ESC” to exit Using arrow button to change “On” or “Off” setting then press “ENT” or press “ESC” to go back. There is no HDD ! The CopySmartPlus has no hard drive, the LCD will show the message as left. 3.11.
MODEL FIRMWARE 01 IDE1 Master CD- RW：BRAND MODEL FIRMWARE 02 IDE2 Master CD-RW：BRAND MODEL FIRMWARE 03 IDE3 Master CD-RW：BRAND MODEL FIRMWARE Press “ENT” button to see the device information and “ESC” to go BACK. Using arrow button to select another device or press “ESC” to go back. Press “ENT” button to see the device information and “ESC” to go back. Using arrow button to select another device or press “ESC” to go back. Press “ENT” button to see the device information and “ESC” to go back.
3.11.15 Quick Erase This function will quick erase the data on the CD-RW discs. It will only take a short time to do it. 11-15. Setup Quick Erase All data will be lost, erase?Yes Erasing disc 00:24 (Quick) Quick Erase OK:01 Fail:00 Press “ENT” button to enter the “Quick Erase” and “ESC” to exit. Use arrow buttons to change “Yes” or “No” setting then press “ENT” or press “ESC” to go back. LCD will show the process of the erasing disc. When erasing disc is finished, the LCD will show the message as left.
Chapter 4 Trouble Shooting 1. No display on LCD or the unit does not operate when power on. Please check the connection of power cable and the environment of power outlet is normal. 2. LCD shows the Error message. During operations like Copy, Test, Compare and Verify, you may press ESC button to abort the operation. An Error message will be shown on the LCD. With some CD writers the abort will cause the duplicator to hang up and you have to re-start the power to return to normal operation.
Appendix 1 Directory Structure 1. Copy 2. Test 3. Test&Copy 4. Verify 5. Compare 6. Prescan 7. Disc Info 8. Select Source 9. Image 10. Edit Track(For AUDIO disc only) 10.01 CD to CD Edit 10.02 CD to HDD Edit 10.03 Play Audio Track 10.04 Close Session 11. Setup 12. Adv Setup 11.01 Language 11.02 Burn Speed 11.03 Read Speed 11.04 Auto Start Drive 11.05 Startup Menu 11.06 Auto Verify 11.07 Auto Compare 11.08 Auto Prescan 11.09 Eject Disc 11.10 Burn On The Fly 11.11 Burn Mode 11.12 Button Sound 11.
Appendix 2 LCD Message List Normal LCD Message List： Message Description Initialize SDRAM Detect Drives User Abort! Analyzing.... Source Drive Not Ready Target Drive Not Ready Source Disc Not Ready Target Disc Not Ready Erasing disc Fail to get Drive Info! Fail to get Src Disc Info! Save new config Fail! Load Default Config? Src&Tgt can't in the same channel Preparing...... Check Target Please Wait......
Audio Edit Messages： Message Description Lost selected Tracks? End edit disc and burn? Continue edit next Disc? Target Overflow Re-Select Close all disc’s session? Can’t edit HDD No AUDIO track in this disc Insert next disc Sessions were closed already ! Burn or Move to partition? Tgt overflow, del last trk? Ins empty disc Continue? Abort the tracks selected and delete it Finish the music disc edit and start to record the CD Asking to continue editing next music disc or not The CD disc space is not enough
