User's Manual
Table Of Contents
- VX 675
- Contents
- Preface
- Terminal Overview
- Terminal Setup
- Selecting Terminal Location
- Unpacking the Shipping Carton
- Examining Terminal Features
- Examining Connection Ports
- Installing the Paper Roll
- Installing the SIM Card
- Installing the SD Card
- Using the Battery
- Battery Behavior (No Power Pack)
- Connecting the Terminal Power Pack
- Charging the Battery
- Using the VX 675 Base Stations
- Powering Up the Base
- Docking the Terminal on the Base
- Undocking the Terminal from the Base
- Conducting Wireless Transactions
- Conducting Smart Card Transactions
- Using the Magnetic Card Reader
- Connecting to USB Host
- VX 675 ECR (Fiscal Module) Support
- VX 675 3G and GPS Support
- Using the Terminal Keys
- Verix Terminal Manager
- File Authentication
- Performing Downloads
- Downloads and Uploads
- Download Methods
- Download Tools
- Download Content
- Full and Partial Downloads
- Support for Multiple Applications
- Use of I: drive and F: drive
- File Authentication Requirements
- Required Certificates and Signature Files
- The File Authentication Process During an Application Download
- File Group Permissions
- Download an Operating System Update Provided by VeriFone
- File Authentication for Back-to-Back Application Downloads
- Timing Considerations Due to the Authentication Process
- Support for File Compression
- Effect of Downloads on Existing Files and Data
- Direct Operating System Downloads
- Back-to-Back Application Downloads
- Specifications
- Maintenance
- VeriFone Service and Support
- System Messages
- Troubleshooting Guidelines
- Port Pinouts
- ASCII Table
- VX 675 Battery Information
- Glossary
- Application ID
- Application program
- Application prompt
- ASCII
- Back-to-back application download
- Baud
- Bit
- Block
- Boot loader
- Buffer
- Byte
- Calendar/clock chip
- Card reader
- Carrier
- Certificate
- Character
- CONFIG.SYS file
- CPU
- Data
- Data entry
- Data packet
- Default
- Delete
- Diagnostics
- Direct download
- Display
- Download
- File authentication
- Firmware
- Fixed prompt
- Flash memory
- Host computer
- Input
- Interface
- Keyed file character set
- Keyed file editor
- Keyed file record
- Keypad
- Local functions
- Manual transaction
- Memory
- Messages
- Non-volatile memory
- Normal Mode
- Packet
- Packet-switched networks
- Parameter
- Password
- PC
- Peripheral terminal
- Port
- POS terminal
- Power pack
- Prompt
- Protocol
- PTID
- RAM
- Remote host computer
- Scroll
- Search key
- Serial port
- Signature file
- mDRAM
- Subroutine
- Swipe
- Verix Terminal Manager
- Verix Terminal Manager password
- Terminal
- Terminal ID
- Terminal-to-terminal application upload
- Track 1, 2, or 3 data
- Transaction
- Variable
- Volatile memory
- Index
- Contact VeriFone
PERFORMING DOWNLOADS
Back-to-Back Application Downloads
VX 675 R
EFERENCE GUIDE 135
The procedure in Table 16 walks you through a back-to-back application
download from a sending VX 675 terminal (Gold) to a receiving VX 675 terminal
(Target).
Back-to-back downloads require that one terminal, the Gold terminal, be loaded
with the required applications. The receiving terminal is the Target terminal. The
procedure in Table 16 assumes the following:
• The Target terminal has no applications loaded.
• There is enough memory in the Target terminal to complete the download.
• You are performing a full download.
NOTE
The Target terminal does not display an error message if there is not enough
memory to complete the download. However, the Gold terminal displays
DOWNLOAD INCOMPLETE before returning to SYS MODE MENU 2.
Table 16 Back-to-Back Application Download Procedure
Step Gold Terminal Target Terminal
1 Connect a MOD10 cable (P/N 05651-XX) between the RS-232 ports of the
terminals using a UART Dongle connected to each terminal.
Allow each terminal to boot up. After boot up, the Target terminal displays
DOWNLOAD NEEDED.
2 Press ENTER+7 to enter Verix Terminal Manager.
3 Enter the Verix Terminal Manager password (factory default is “1 6 6 8 3 1”
and press
ENTER.
4 Press the * (asterisk) key, then press
ENTER. You are prompted to reenter
the Verix Terminal Manager
password.
UPLOADING NOW is displayed.
Press 3, DOWNLOAD, to enter
download mode.
5 Press ENTER at the next VERIX
TERMINAL MGR DOWNLOAD
screen
to select
FILE GROUP_1 (default
displayed) as the target file group.
6 For a single application download,
select
Single-app. For multiple
application download, select
Multi-app
in the next VERIX TERMINAL MGR
DOWNLOAD screen.