User's Manual
Table Of Contents
- VX 675
- Contents
- Preface
- Terminal Overview
- Terminal Setup
- Selecting Terminal Location
- Unpacking the Shipping Carton
- Examining Terminal Features
- Examining Connection Ports
- Installing the Paper Roll
- Installing the SIM Card
- Installing the SD Card
- Using the Battery
- Battery Behavior (No Power Pack)
- Connecting the Terminal Power Pack
- Charging the Battery
- Using the VX 675 Base Stations
- Powering Up the Base
- Docking the Terminal on the Base
- Undocking the Terminal from the Base
- Conducting Wireless Transactions
- Conducting Smart Card Transactions
- Using the Magnetic Card Reader
- Connecting to USB Host
- VX 675 ECR (Fiscal Module) Support
- VX 675 3G and GPS Support
- Using the Terminal Keys
- Verix Terminal Manager
- File Authentication
- Performing Downloads
- Downloads and Uploads
- Download Methods
- Download Tools
- Download Content
- Full and Partial Downloads
- Support for Multiple Applications
- Use of I: drive and F: drive
- File Authentication Requirements
- Required Certificates and Signature Files
- The File Authentication Process During an Application Download
- File Group Permissions
- Download an Operating System Update Provided by VeriFone
- File Authentication for Back-to-Back Application Downloads
- Timing Considerations Due to the Authentication Process
- Support for File Compression
- Effect of Downloads on Existing Files and Data
- Direct Operating System Downloads
- Back-to-Back Application Downloads
- Specifications
- Maintenance
- VeriFone Service and Support
- System Messages
- Troubleshooting Guidelines
- Port Pinouts
- ASCII Table
- VX 675 Battery Information
- Glossary
- Application ID
- Application program
- Application prompt
- ASCII
- Back-to-back application download
- Baud
- Bit
- Block
- Boot loader
- Buffer
- Byte
- Calendar/clock chip
- Card reader
- Carrier
- Certificate
- Character
- CONFIG.SYS file
- CPU
- Data
- Data entry
- Data packet
- Default
- Delete
- Diagnostics
- Direct download
- Display
- Download
- File authentication
- Firmware
- Fixed prompt
- Flash memory
- Host computer
- Input
- Interface
- Keyed file character set
- Keyed file editor
- Keyed file record
- Keypad
- Local functions
- Manual transaction
- Memory
- Messages
- Non-volatile memory
- Normal Mode
- Packet
- Packet-switched networks
- Parameter
- Password
- PC
- Peripheral terminal
- Port
- POS terminal
- Power pack
- Prompt
- Protocol
- PTID
- RAM
- Remote host computer
- Scroll
- Search key
- Serial port
- Signature file
- mDRAM
- Subroutine
- Swipe
- Verix Terminal Manager
- Verix Terminal Manager password
- Terminal
- Terminal ID
- Terminal-to-terminal application upload
- Track 1, 2, or 3 data
- Transaction
- Variable
- Volatile memory
- Index
- Contact VeriFone
TERMINAL SETUP
Installing the SIM Card
22 VX 675 REFERENCE GUIDE
Installing the
SIM Card
The VX 675 terminal for GPRS modems supports the installation of a GSM SIM
(Subscriber Identity Module). Use the following procedure to install a SIM card.
To install or replace
the card
1 Turn off the terminal.
2 Place the terminal upside down on a soft, clean surface to protect the lens
from scratches.
3 Unscrew and remove the back compartment cover.
4 Lift the battery pack.
Figure 9 Removing the Back Compartment Cover
5 Insert the SIM card into the cardholder.
Figure 10 Inserting the SIM Card
%
$
NOTE
There is only one SIM slot (VX 675 3G has dual SIM support). Before inserting
the SIM card, position it as shown in in the illustration below, with the card’s gold
contacts facing the compartment. The cardholder connector base has a set of
contacts and a notch to ensure the SIM/R-UIM card is positioned correctly. The
SIM card has a notch on one corner to ensure that it fits into the connector base in
only one way.
'&
0,
6
0
,6
$
%